Controls and Control Theory Commons^™

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Use Of The Igbt Module In The Active Region To Design A High Current Active Filter, Jorge F. Galarraga

Graduate Theses and Dissertations

Particle accelerators require high-precision magnetic fields on the order or 100ppm or less. This implies that the precision of the associated electrical current in the electromagnet that generates these fields should be smaller than 100ppm. However, conventional switching power supplies cannot offer this precision due to the frequency limitation of the switches. This research considers the use of power electronics devices operating in a linear as an alternative solution to meet the requirements of particle accelerator electromagnets.

This thesis presents the study of an insulated-gate bipolar transistor (IGBT) driver using a new control method that linearizes the IGBT’s collector-emitter voltage …

Models And Fuzzy Microclimate Control System In The Storage Of Archival Documents, Avaz Marakhimov Scd, Prof, Abdushukur Abdullaev

Chemical Technology, Control and Management

In this article, the main object of research is the creation of appropriate microclimatic conditions to ensure reliable and high-quality storage of archival documents, as well as automatic control of the optimal values of the main parameters of the external and internal environment that directly affect the quality of storage. To control the microclimate, three categories of models for automatic control of these parameters are considered separately in the archives: the “white box”, “black box” and “gray box " models. The results of the analysis of the advantages and disadvantages of the considered models are presented. The generalized structure …

Developing Algorithms For Automating The Processes Of Forming The Optimal Structural Composition Of Production - Technological Modules, Alisher Mamajanov, Sarvar Botir Ugli Nabiyev

Chemical Technology, Control and Management

In this research, we developed appropriate algorithms for the formation of the optimal structural composition of production - technological modules (PTM) based on the automation of the processes of determining and ensuring the functional-parametric compatibility (FPC) of their components. These algorithms are based on the developed mathematical models on the basis of the use of analytical methods for implementing the interconnection between the main components of the PTM.

A Study On Dynamic Characteristics Of A New Remote Transformer Current Converter Without Compensating Capacitor, Sulton Faizullaevich Amirov, Nargisa Kamilovna Babanazarova, Nurullo Rahmatullaevich Yuldashev

Chemical Technology, Control and Management

In this research paper, analytical equations of the transient characteristics of a new remote transformer current converter without a compensating capacitor have been obtained when a stepwise, linearly increasing, sinusoidal and sinusoidal with a damped amplitude of effects was applied to their input. It has been shown that the developed current converter can be represented in the structural schemes of monitoring and control systems in the form of a series-connected real differentiating link without statism and inertial (aperiodic) link of the first order, and in the case of neglecting active losses in the magnetic circuit and when the converter is …

Problem Solving Methods For Synthesis Of Physical Principles Of Mechatronic Module Operations In Intelligent Robotic Systems, Nazarov Khayriddin Nuritdinovich

Chemical Technology, Control and Management

The scientific paper investigates the methods for solving problems of synthesis of physical principles of operation of mechatronic modules of intelligent robotic systems are considered.

In addition, it deals with the specifics of the process of synthesis of the physical principles of the operation of mechatronic modules using predicate models, list models and information matrices of physical and technical effects.

It shows the interpretation of the components of the model of the system for the synthesis of the physical principles of operation of mechatronic modules of intelligent robotic systems and automatic control and the features of the synthesis algorithm for …

Issues In Functioning Efficiency Of Security Monitoring Systems In Infocommunication Systems, Majid Karimov Malikovich, Sevara Khamdamova Mirazizovna

Chemical Technology, Control and Management

The security monitoring system (SMS) receives information from the means of protection, detecting attacks, systems for monitoring the functioning of information communication systems (ICS) and performs adaptive security management of ICS, providing a flexible response of the security system to the actions of the intruder. In this case, the result of the functioning of the SMB are recommendations for modifying the ICS security system, in accordance with the specified restrictions, in order to minimize the possible damage from the implementation of threats. A complex of security systems is used in modern ICS. Typically, different systems are not linked and are …

Identification Of Key Persons In The Information Security Incident Management Process And Distribution Of Roles Between Them, Fayzullajon Bakhtiyorovich Botirov, Sharifjon Rakhimovich Gafurov, Azam Anvorovich Gafurov

Chemical Technology, Control and Management

This research paper is devoted to the process of information security incident management and the distribution of the roles of key persons in this process. The skills required for members of the information security incident response team are considered, positions and responsibilities are given - typical positions that exist in each organization, testing and improvement procedures are given, the role of the information security incident response team members and employee positions is shown. The quality of the group leader is reflected; responsible for personnel management, scoping and reporting on the state of the organization at a higher level of the …

Results Of X-Ray Phase And Ir-Spectral Analysis Of Azosuperphosphates Obtained On The Basis Of Phosphorites Of Central Kizilkum, Elyor Atashev, Maksud Jabbievich Jumaniyazov, Sayfitdin Mukhitdinovich Tadjiev

Chemical Technology, Control and Management

This article is devoted to the use of ammonium sulfate in the production of nitrogen-phosphorus fertilizers, which are widely used in agriculture today. In the research work, the possibilities of obtaining azo superphosphate are described in detail by the use of intensive technology based on low-grade phospharites of the Central KyzylKum. X-ray and IR-spectroscopic analyzes of a new type of NP-complex fertilizers obtained using a solution of ammonium sulfate in sulfuric acid are described in detail. The X-ray analysis of the obtained sample on the X-ray diffraction pattern of the azo-superphosphate fertilizer revealed the appearance of peaks in the interplanar …

Enterprise Engineering And Intellectual Technologies For Lifecycle Management Of Industrial Production, Nodirbek Rustambekovich Yusupbekov, Valery Borisovich Tarasov, Shukhrat Manapovich Gulyamov, Fahritdin Raupovich Abdurasulov

Chemical Technology, Control and Management

The fundamental scientific problem of the development of the mathematical foundations of engineering for industrial enterprises and the development of mathematical methods of production management, as well as the creation of intelligent systems for coordinated management of the life cycles of products and production in the network of enterprises are discussed. The issues in demand in the development of a vast interdisciplinary field of enterprise engineering and the development of modern network enterprises and intelligent production using mathematical modeling methods are discussed.

Autonomous Navigation Of The Surface Autonomous Vehicle For Emergency Rescue (Saver), Andrew Skow

ENGS 88 Honors Thesis (AB Students)

Once dropped into the ocean, SAVER will autonomously navigate towards the Advanced Next-Generation Emergency Locator beacon, worn by every NASA astronaut, that emits a 121.5 MHz distress signal. Using a rotating directional loop antenna SAVER is able to detect and identify the direction of the distress beacon and navigate itself towards the signal source. The autonomous navigation system is dependent on several electrical, and mechanical systems to function properly and presents a novel systems engineering problem. Given testing limitations, NASA requires that SAVER is designed to operate indoors and with an umbilical power supply. The radio direction finding (RDF) system …

Solar Pv Emulator, Tristan Studer, Cody Kremer

Electrical Engineering

The implementation of a solar PV emulator. Creating a controllable testing environment which sufficiently recreates realistic conditions a photovoltaic cell would experience in real world use. The project aims to accurately show the efficiency and reliability of a solar PV cell, opposed to an ideal model which creates unrealistic expectations. The PV emulator implements conditions such as: irradiance, soiling and temperate changes. It gives feedback on a displayed IV curve and/or PV curve so the user may graphically analyze the output their PV cell produces given various conditions. It allows the user selectable conditions the solar cell may experience this …

A Study Of Hygrometer Based On The Method Of Intracavity Laser Absorption, Abdulaziz Muminovich Nazarov Prof, Mirkomil Mirhidoyat Ogli Xasanov

Chemical Technology, Control and Management

The article presents the results of experimental studies of a fiber-optic humidity sensor, the principle of operation of which is based on the method of intracavity laser absorption. A method of intracavity laser absorption is described, which makes it possible to dramatically increase the sensitivity of the fiber humidity sensor by switching to it. A schematic diagram of a fiber optical humidity sensor using a differential detection scheme and a design of an active ring laser fiber consisting of a diode pump laser, a fiber pump beam splitter, two directional couplers, a measuring ring laser, a ring comparison laser, two …

Application Of The Ultrasonic Generator In The Extractor And Determination Of Its Energy Consumption, Shaxnoza Abduvaxitovna Sultanova, Jasur Esirgapovich Safarov, Azamat Usenov, Doston Ishmuhammat Ogli Samandarov

Chemical Technology, Control and Management

An ultrasonic generator was used in the Soxhlet extractor. To evaluate the process, the solvent flow was examined. The influence of the flow time in the Soxhlet on the process was analyzed. The formula for the residence time of streaming particles in the apparatus is given. A standardized volume curve V was formed. The time required for the solvent to remain in the apparatus is important during the extraction process. The description of the structure of flows of mass metabolic processes also means that it allows you to determine the movement and distribution of substances in these flows. Therefore, we …

Main Stages Of Automated System Of Processes For Determining And Ensuring Functional And Parametric Compatibility Of Production And Technological Systems, Sarvar Botir Ugli Nabiyev

Chemical Technology, Control and Management

This article presents the main stages of the development of an automated system of processes for determining and ensuring functional and parametric compatibility (FPC) of components of production and technological systems (PTS), in particular production and technological modules (PTM) of machine-building production, respectively, based on the analysis and systematization of technological zones of loading of the main technological equipment (MTE) and the construction of coating surfaces, the main parameters of industrial robots and storage systems (SS), determination and mathematical formalization of coating surfaces and guiding planes of MTE loading zones, formation of types of analytical dependences of FPC PTM functions, …

Errors Of Universal Contactless Converters Of Monitoring And Control Systems From External Magnetic Fields, A.M Plakhtiev, Gayratjon Gaziev, Yahyojon Meliboyev, Odil Doniyorov

Chemical Technology, Control and Management

In communication and communication devices, power equipment, relay protection and automation terminals, in the electric power industry of "smart" cities and homes, in industry, in railway transport, microprocessor-based relay protection and automation devices, distributed generation installations, including renewable energy sources, and electricity storage, as well as "intelligent" automated information and measurement systems are beginning to be used. Contactless converters of direct and alternating currents of control and control systems are widely used in them. Their disadvantages are a narrow range of controlled currents, large dimensions and weight. Therefore, it is important to eliminate them. The paper discusses the general principles …

Development And Implementation Of Two-Dimensional Fault-Tolerant Programmable Logical Controllers, Azizbek Nodirbekovich Yusupbekov, Nodirjon Turgunboy Ugli Tulaganov, Khurshid Salim Ugli Turaev

Chemical Technology, Control and Management

It has been revealed that a significant part of industrial control systems designed for technological facilities with more than one input and one output and the most widespread are objects with two inputs and two outputs.The article describes the programming environment for fault-tolerant two-dimensional control systems using PID controller, which software is implemented in an environment for programmable logic controllers (PLC).An experimental testing system has been implemented and software settings and regulator settings have been considered. Real-time PID controllers and filters have been implemented. It has been implemented a variation of the control system software with object imitation.

Production Of Lime-Ammonium Nitrate Based On Chalk, Nitrate And Ammonium Sulfate, O.X. Rasulov, Abdurasul Mamataliyev, M.X. Dadaxodjaeva, Sh.S. Namazov, B.M. Beglov

Chemical Technology, Control and Management

The article studies the process of obtaining carbonate-ammonium nitrate (CAN) based on the mixing of melt ammonium nitrate (NH₄NO₃) with chalk (СаСО₃) and ammonium sulfate (NH₄)₂SO₄). For the granulation of nitrate-sulfate-carbonate melt the prilling method is applied using a granulation tower. Determined the composition and properties of new types of fertilizers. It is shown that with the ratio NH₄NO₃ : СаСО₃ : (NH₄)₂SO₄ = 100 : 24 : 1 the product contains 28,03% N, SO₃ – 0,50%, 10% …

Selection Of Mineral Raw Material Fields For Glauconite Sorption Materials, Diyor Xadjibayev, Furkat Ilyasovich Erkabaev

Chemical Technology, Control and Management

Natural minerals, such as bentonite, kaolinite, biotite, vermiculite, and glauconite, which have sufficiently high performance properties in the softening of industrial and waste water, softening and cleaning of heavy metals, are promising. To study the physical and chemical properties of glauconites from various deposits of the country, samples of glauconite mineral were brought from the Parkent, Bukhara, and Karakalpak mountain reserves, their physical and chemical properties were studied, compared with each other, and the optimal reserve was selected. The reserves of these deposits are sufficient and have the potential for industrial development. The purpose of this study is to compare …

Mathematic Simulation Of Glass Melting Process In Glass Production, Shuhrat Manapovich Gulyamov, Azamat Toirovich Rajabov, Utkir Uktam Ugli Kholmanov

Chemical Technology, Control and Management

A systematic analysis of the technological process of glass melting as an object of automatic control and management has been carried out. As an object of automatic control with distributed parameters, the mathematical description of the glassmaking furnace operation has been developed (considering the main phenomenological features of the technological mode of glassmaking).In this paper, a mathematical description of charge melting process, additional heating by electric current, bubbling, thermal conductivity and heat fluxes during the processing of molten glass have been generated. Initial conditions and simplifying assumptions have been derived. The model is based on the equations of continuity, momentum …