Polymer Science Commons^™

Research Of New Fireproof Supplied Polymer Composites Based On Epoxy Resin For Metal Structures, Kuvondiq Murtazaev, F.N. Nurkulov, D.N. Mukhiddinov, M.T. Аbdirova

Technical science and innovation

In the article proposes new compositions based on fire retardant expanded polymer composites of epoxy resin ED-20 and phosphorus-containing oligomers, catalysts, aluminum hydroxide and nitrogen-containing compounds.

The obtained sample of fire retardant expanded polymer composites based on epoxy resin, as well as the initial substances, were investigated by IR spectroscopy (Nicolet 5700), thermogravimetric analysis (TG) (SDT Q600) of physical and chemical properties and determination of fire retardant efficiency according to GOST R 53295-2009.

Infrared spectroscopy has been used to determine the bends and epoxy groups that characterize composites, as well as to determine the frequencies of phosphorus, nitrogen, and metal-containing …

Development Of Polymeric Cxcr4 Targeting Carriers For Sirna Delivery To Treat Acute Kidney Injury, Weimin Tang

Theses & Dissertations

Acute kidney injury (AKI) is a major kidney disease that is characterized by a sudden loss of renal function which manifests by a decrease in urine output and an increase in serum creatinine. AKI is a global healthcare burden associated with high morbidity, mortality, and increasing cost. Currently there are no effective pharmacological treatments available. Apoptosis induced by p53 has been demonstrated as an important pathological mechanism for the development of AKI. Meanwhile, CXCR4/SDF-1 axis has been associated with the inflammation during AKI, and CXCR4 is overexpressed on injured tubules. This dissertation hypothesized that polycations with CXCR4 targeting ability could …

Polymeric Nanofibers Supported Metal Oxides For Electrochemical Energy Storage Devices, Rutul Patel

Electronic Theses & Dissertations

With increasing demand for energy, there is an increased need to find effective ways to store the available energy to sustain current and future generations. Thus, the research investigates whether polymetric nanofibers support metal oxide are a good solution to store energy. The materials used for synthesis includes N-dimethylformamide, nickel nitrate, cobalt nitrate and polyacrylonitrile.

These fibers are developed three phases. First, a homogenous mixture is prepared, followed by electrospinning of the mixture. Next, calcination of the prepared nanofibers was done to generate the 1D nanofibers embedded with metal oxides. The samples are primarily tested for supercapacitor applications, hydrogen evolution …

Water Recovery From Bioreactor Mixed Liquors Using Forward Osmosis With Polyelectrolyte Draw Solutions, Calen Raulerson

All Theses

The objective of this research was to test the feasibility of using forward osmosis (FO) with polyelectrolyte draw solutions to recover water from bioreactor mixed liquors. When combined with an Anaerobic Osmotic Membrane Bioreactor (AnOMBR), such a system could process fecal and food waste from astronauts aboard the International Space Station (ISS) and reclaim important nutrients and water. This project focused on measuring the obtainable water recovery rates from bioreactor effluent, and the identifying challenges associated with the operation.

AnOMBRs feature several advantages over aerobic bioreactors, and non-osmotic anaerobic membrane bioreactors (AnMBR). Anaerobic bioreactors avoid the significant energy costs of …

Extraction Methodologies And Physicochemical Characterizations Of Nanocellulose Isolated From Kudzu For Potential Sustainable Packaging Applications, Elliott Love

All Theses

Flexible packaging is an integral part of the food supply chain due to its unique thermal, mechanical, and barrier properties. The many advantages (e.g., lightweight, product protection, reduction in food waste, communication medium, etc.) come with certain drawbacks (low recyclability rate, pollution of ecosystems, etc.). Still, the heavy reliance of the food industry on these products, many of them being non-sustainable polyolefins, is unlikely to diminish in the foreseeable future. Thus, more sustainable alternatives that do not sacrifice performance (machinability, shelf-life, etc.) are needed before pollution becomes irreversible and public outcry insurmountable. Nanocellulose, especially in the form of cellulose nanocrystals …

Approaching Disorder-Tolerant Semiconducting Polymers, Xinwen Yan, Miao Xiong, Xin Yu Deng, Kai Kai Liu, Jia Tong Li, Xue Qing Wang, Song Zhang, Nathaniel Prine, Zhuoqiong Zhang, Wanying Huang, Yishan Wang, Jie Yu Wang, Xiaodan Gu, Shu Kong So, Jia Zhu, Ting Lei

Faculty Publications

Doping has been widely used to control the charge carrier concentration in organic semiconductors. However, in conjugated polymers, n-doping is often limited by the tradeoff between doping efficiency and charge carrier mobilities, since dopants often randomly distribute within polymers, leading to significant structural and energetic disorder. Here, we screen a large number of polymer building block combinations and explore the possibility of designing n-type conjugated polymers with good tolerance to dopant-induced disorder. We show that a carefully designed conjugated polymer with a single dominant planar backbone conformation, high torsional barrier at each dihedral angle, and zigzag backbone curvature is highly …

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Emergence Of Non-Hexagonal Crystal Packing Of Deswollen And Deformed Ultra-Soft Microgels Under Osmotic Pressure Control, Molla R. Islam, Rachel Nguyen, L. Andrew Lyon

Biology, Chemistry, and Environmental Sciences Faculty Articles and Research

Highly solvent swollen poly(N-isopropylacrylamide-co-acrylic acid) microgels are synthesized without exogenous crosslinker, making them extremely soft and deformable. These ultralow crosslinked microgels (ULC) are incubated under controlled osmotic pressure to provide a slow (and presumably thermodynamically controlled) approach to higher packing densities. It is found that ULC microgels show stable colloidal packing over a very wide range of osmotic pressures and thus packing densities. Surprising observation of co-existence between hexagonal and square lattices is also made over the lower range of studied osmotic pressures, with microgels apparently changing shape from spheres to cubes in defects or grain boundaries. It is proposed …

Tools And Strategies For The Patterning Of Bioactive Molecules And Macromolecules, Daniel J. Valles

Dissertations, Theses, and Capstone Projects

Hypersurface Photolithography (HP) is a printing method for fabricating structures and patterns composed of soft materials bound to solid surfaces and with ~1 micrometer resolution in the x, y, and z dimensions. This platform leverages benign, low intensity light to perform photochemical surface reactions with spatial and temporal control of irradiation, and, as a result, is particularly useful for patterning delicate organic and biological material. In particular, surface- initiated controlled radical polymerizations can be leveraged to create arbitrary polymer and block- copolymer brush patterns. Chapter 1 will review the advances in instrumentation architectures from our group that have made these …

Gum Arabic-Capped Silver Nanoparticles For Electrochemical Amplification Sensing Of Methylene Blue In River Water, Ziad Khalifa, Moustafa Zahran, Magdy Zahran, Magdi Abdelazzem

Chemical Engineering

Herein, a novel electrochemical amplification sensor is developed for detecting methylene blue (MB) us- ing gum Arabic-capped silver nanoparticles (AgNPs) for the first time. Gum Arabic-AgNPs were fabricated via a direct chemical reduction technique using silver nitrate as an AgNPs precursor and gum Arabic as a reducing and capping agent. They were characterized using ultraviolet-visible (UV–Vis) spectrophotom- etry, square wave voltammetry (SWV), and transmission electron microscopy (TEM). UV–Vis and SWV results show the characteristic absorption and electrochemical oxidation peaks of the AgNPs at 431 nm and 0.18 V, respectively. Additionally, TEM images of the AgNPs show that they are spherical …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Epoxy Curing: Paramount Or Trivial? A Cure Path Dependent Inquiry, Jared Bates

Dissertations

The presented research delves into epoxy network formation corroborating reactant concentration profiles and physical property development throughout cure, providing an experimental basis for burgeoning molecular dynamics and coarse-grained simulation methodologies. Herein, three primary subjects were investigated: the first two examine neat and toughened epoxide/amine network formation with respect to various cure profiles aimed at altering reaction pathways, the final chapter intends to augment traditionally utilized activation energy (E_a) methodologies.

Neat and toughened epoxide/amine slurries were monitored in-situ throughout cure via near infrared (NIR) spectroscopy and rheological techniques. Functional group conversion and moduli development were related with specific attention …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Mechanisms Of Spontaneous Curvature Inversion In Compressed Graphene Ripples For Energy Harvesting Applications Via Molecular Dynamics Simulations, James M. Mangum, Ferdinand Harerimana, Millicent N. Gikunda, Paul M. Thibado

Physics Faculty Publications and Presentations

Electrically conductive, highly flexible graphene membranes hold great promise for harvesting energy from ambient vibrations. For this study, we built numerous three-dimensional graphene ripples, with each featuring a different amount of compression, and performed molecular dynamics simulations at elevated temperatures. These ripples have a convex cosine shape, then spontaneously invert their curvature to concave. The average time between inversion events increases with compression. We use this to determine how the energy barrier height depends on strain. A typical convex-to-concave curvature inversion process begins when the ripple’s maximum shifts sideways from the normal central position toward the fixed outer edge. The …

Investigation Of Membrane Based Processes For Biomedical Applications, Efecan Pakkaner

Graduate Theses and Dissertations

As substantial developments were achieved in nanotechnology and polymer engineering, especially in the last few decades, the use of membranes and membrane-based procedures was found to be expanding into more and more research and development areas; including biological engineering, life sciences and biomedical engineering. Not only have they been the main focus of meaningful research, but they have also been the main pieces of the solutions to very thorny problems encountered within a wide range of applications from microfluidics to water treatment, thanks to their versatility, cost-effectiveness and biocompatibility, when compared to conventional separation techniques. To celebrate and embrace these …

High Performance Mixed-Matrix Electrospun Membranes For Ammonium Removal From Wastewaters, Shu-Ting Chen, Sumith Ranil Wickramasinghe, Xianghong Qian

Chemical Engineering Faculty Publications and Presentations

Mixed-matrix electrospun membranes were developed to investigate ammonium removal from low ammonium concentration wastewaters for the first time. Particles derived from the inexpensive zeolite 13X were successfully incorporated into polyethersulfone (PES) matrices. The fabricated mixed-matrix electrospun membranes demonstrate high ammonium removal capacity reaching over 55 mg/g_zeolite, more than 2.5 times higher than the previously fabricated mixed-matrix membranes via non-solvent induced phase inversion. Moreover, the membranes fabricated exhibit high permeability and ease of regeneration. Over 90% of total ammonium nitrogen (TAN) can be removed from low TAN wastewaters such as aquaculture wastewaters. In addition to zeolite 13X, other zeolite …

Promotion Of Human Schwann Cell Proliferation Using Heparin/Collagen Coated Nerve Conduits, John Magness

Chemical Engineering Undergraduate Honors Theses

Often in the aftermath of an injury or surgery, the sense of touch and muscle control is lost in the affected area as nerves are damaged or severed and fail to grow back completely. The regeneration of the nerve cells can be promoted by treating the nerves with nerve conduits. Nerve conduits are hollow cylinders of bio-compatible materials that can be surgically implanted to the disconnected nerve to promote and direct the growth of nerves. The objectives of this research are to investigate the ability of nerve conduits treated with layer-by-layer coatings to promote the growth of Schwann cells, to …

Peptoid-Based Microsphere Coatings For Biomaterial Applications, Jesse Leland Roberts

Graduate Theses and Dissertations

Peptoids are peptidomimetic oligomers that predominantly harness similarities to peptides for biomimetic functionality. The incorporation of chiral, aromatic side chains in the peptoid sequence allows for the formation of distinct secondary structures and self-assembly into supramolecular assemblies, including microspheres. Peptoid microspheres can be coated onto substrates for potential use in biosensor technologies, tissue engineering platforms, and drug-delivery systems. They have the potential for use in biomedical applications due to their resistance to proteolytic degradation and low immunogenicity. This dissertation focuses on the physical characteristics and robustness of the peptoid microsphere coatings in various physiological conditions, along with their ability to …

Biopolymeric Materials For Tissue Regeneration, Cell Manufacturing, And Drug Delivery, David Alfonso Castilla-Casadiego

Graduate Theses and Dissertations

The development of materials for tissue regeneration, cell manufacturing, and drug delivery is possible by the manipulation of polymer properties and the use of three different techniques including layer-by-layer, electrospinning, and molding technique.

By applying the layer-by-layer technique over biomaterials, it is possible to develop polymeric multilayers that promote a more favorable environment for cellular functionality, increasing the possibility of improving their acceptance in the area of implantation. IRVASE demonstrated being a powerful technique that allows for a reliable characterization of the physical-chemical and thermal properties of the fabricated surfaces. This opens the possibility to monitor the design of surfaces …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …