Chemical Engineering Commons^™

Capture And Recycle Of Industrial Co2 Emissions Using Mircoalgae, Michael H. Wilson, Daniel T. Mohler, John G. Groppo, Thomas E. Grubbs, Stephanie Kesner, E. Molly Frazar, Aubrey Shea, Czarena L. Crofcheck, Mark Crocker

Center for Applied Energy Research Faculty and Staff Publications

A novel cyclic flow photobioreactor (PBR) for the capture and recycle of CO₂ using microalgae was designed and deployed at a coal-fired power plant (Duke Energy’s East Bend Station). The PBR was operated continuously during the period May–September 2015, during which algae productivity of typically 0.1–0.2 g/(L day) was obtained. Maximum CO₂ capture efficiency was achieved during peak sunlight hours, the largest recorded CO₂ emission reduction corresponding to a value of 81 % (using a sparge time of 5 s/min). On average, CO₂ capture efficiency during daylight hours was 44 %. The PBR at East Bend …

Preparation And Microstructure Of Machinable Al2O3/Mica Composite By Ball Milling And Hot-Press Sintering, Qingbo Tian, Deyu Kong, Tongguang Zhai

Chemical and Materials Engineering Faculty Publications

A machinable α-Al₂O₃/mica composite was prepared by hot-press sintering. In this experiment, a mica-contained glass ceramic in the MgO-Al₂O₃-SiO₂-F glassy system was employed and the base glass powders were obtained by traditional melting-quenched method. Then, α-Al₂O₃ milling swarf was introduced by medium α-alumina milling ball to the glass powders. The test results indicate that the composites consist of mica crystal and mullite crystal, which are precipitated in the base glass. The α-Al₂O₃ shows an irregular polygon, which is inlayed in the base material. With …

Materials And Techniques Used In Cranioplasty Fixation: A Review, Basel A. Khader, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Cranioplasty is the surgical repair of a deficiency or deformity of the skull. The purpose of cranioplasty is to provide protection for the brain following cranial surgery, and to offer relief to psychological disadvantages while increasing social performance. There are several materials that had been used for cranioplasty, but an ideal product has yet to be developed, hence the ongoing research into biologic and non-biologic alternatives to the existing materials. This article critiques the products currently used for cranioplasty in order to facilitate the development of new materials, which can improve patient outcomes.

Conversion Of Glycerol To 1,3-Propanediol Under Haloalkaline Conditions, Melanie R. Mormile, Daniel William Roush, Dwayne A. Elias, Oliver C. Sitton

Biological Sciences Faculty Research & Creative Works

A method of producing 1,3-propanediol. The method comprises fermenting a haloalkaliphilic species of Halanaerobium with a source of glycerol into 1,3-propanediol, at a pH of greater than about 10 and at a salt concentration of greater than about 5% w/v. Furthermore, with supplementation of vitamin B₁₂, the yield of 1,3-propanediol to glycerol can be increased.

The Use Of A Fractional Factorial Design To Determine The Factors That Impact 1,3-Propanediol Production From Glycerol By Halanaerobium Hydrogeniformans, Shivani Kalia, Jordan Trager, Oliver C. Sitton, Melanie R. Mormile

Biological Sciences Faculty Research & Creative Works

In recent years, biodiesel, a substitute for fossil fuels, has led to the excessive production of crude glycerol. The resulting crude glycerol can possess a high concentration of salts and an alkaline pH. Moreover, current crude glycerol purification methods are expensive, rendering this former commodity a waste product. However, Halanaerobium hydrogeniformans, a haloalkaliphilic bacterium, possesses the metabolic capability to convert glycerol into 1,3-propanediol, a valuable commodity compound, without the need for salt dilution or adjusting pH when grown on this waste. Experiments were performed with different combinations of 24 medium components to determine their impact on the production of …

Processing Of Cds/Cdte Solar Cell And The Growth Model Of Cdte Thin Film, Guogen Liu

Dissertations

Cadmium telluride is the only thin film photovoltaic (PV) technology to surpass crystalline silicon PV in the cost. The most common CdTe solar cells consist of a simple p-n heterojunction structure containing a p-doped CdTe layer and n-doped cadmium sulfide (CdS) layer, which acts as a window layer. Cadmium Sulfide (CdS) thin films are often deposited on glass substrates coated with TCO layers by the close-spaced sublimation (CSS) or sputter techniques in industrial because of in-line production integration. It is seldom reported that CdS is deposited by the chemical bath deposition (CBD) batch process. The bottleneck of CBD for commercial …

Synthesis And Tribological Behavior Of Ultra High Molecular Weight Polyethylene (Uhmwpe)-Lignin Composites, Surojit Gupta, Mohammad F. Riyad, Yun Ji

Chemical Engineering Faculty Publications

In this paper, we report the synthesis and characterization of ultra-high molecular weight polyethylene (UHMWPE)-lignin composites. During this study four different compositions, namely UHMWPE, UHMWPE-13 wt. % lignin, UHMWPE-25 wt. % lignin and UHMWPE-42.5 wt. % lignin were fabricated by hot pressing. Detailed microstructural studies by scanning electron microscopy (SEM) showed that UHMWPE and UHMWPE-13 wt. % lignin had a uniform microstructure, whereas UHMWPE-25 wt. % lignin and UHMWPE-42.5 wt. % lignin samples were riddled with pores. UHMWPE and UHMWPE-13% lignin showed comparable flexural strengths of ~32.2 MPa and ~32.4 MPa, respectively. However, the flexural strength dropped drastically in UHMWPE-25 …

Hydrothermal One-Step Synthesis Of Layered Nickel/Cobalt Double Hydroxide With Using Shape-Directing Agent And Homogeneous Precipitating Agent, Li-Wei Zhu, Yun-Hai Yan, Hui Jia, Run-Fen Liang

Journal of Electrochemistry

Nickel/cobalt double hydroxide (Ni/Co-DH) has been prepared by facile hydrothermal one-step synthesis method using hexamethylene tetramine (HMT) as a homogeneous precipitating agent and cetyltrimethylammonium bromide (CTAB) as a shape-directing agent. With the hydrolysis of HMT and the use of CTAB, the Ni/Co-DH could be synthesized without additional alkali source, and in the meantime, the Ni/Co-DH exhibited a controlled mesopore size of 13.4 nm and a large BET surface area of 93.6 m² •g^-1 . The X-ray diffraction (XRD) pattern displays that the Ni/Co-DH existed as a mixture of α-Ni(OH)₂-β-Co(OH)₂. The scanning electron microscope (SEM) …

Computational Fluid Dynamics Modeling And Simulations Of Fluidized Bed Reactors For Chemical Looping Combustion, Subhodeep Banerjee

McKelvey School of Engineering Graduate Student Theses & Dissertations

Chemical looping combustion (CLC) is a next generation combustion technology that shows great promise as a solution for the need of high-efficiency low-cost carbon capture from fossil fueled power plants. To realize this technology on an industrial scale, the development of high-fidelity simulations is a necessary step to develop a thorough understanding of the CLC process. Although there have been a number of experimental studies on CLC in recent years, CFD simulations have been limited in the literature.

In this dissertation, reacting flow simulations of a CLC reactor are developed using the Eulerian approach based on a laboratory-scale experiment of …

Nanostructured Thin Film Synthesis By Aerosol Chemical Vapor Deposition For Energy Storage Applications, Tandeep Singh Chadha

McKelvey School of Engineering Graduate Student Theses & Dissertations

Renewable energy sources offer a viable solution to the growing energy demand while mitigating concerns for greenhouse gas emissions and climate change. This has led to a tremendous momentum towards solar and wind-based energy harvesting technologies driving efficiencies higher and costs lower. However, the intermittent nature of these energy sources necessitates energy storage technologies, which remain the Achilles heel in meeting the renewable energy goals. This dissertation focusses on two approaches for addressing the needs of energy storage: first, targeting direct solar to fuel conversion via photoelectrochemical water-splitting and second, improving the performance of current rechargeable batteries by developing new …

Nanoparticle Formation In The Flame Synthesis Of Multicomponent Nanostructured Materials For Clean Energy Applications, Jiaxi Fang

McKelvey School of Engineering Graduate Student Theses & Dissertations

This dissertation studies the initial stages of particle formation during the combustion synthesis of multicomponent nanomaterials. Combustion is commonly used for the production of nanomaterials at industrial scales and has advantages of high production rates, low waste generation, and scalability. However, there are limitations in being able to apply this synthesis approach to more advanced multicomponent systems. Gas to particle conversion in flames occurs through precursor decomposition, collisional growth, coagulation, condensation, and sintering. There is a fundamental gap in knowledge on the initial stages of particle formation in flames below 2nm due to measurement difficulties and instrumentation limitations. Using a …

Crumpled Graphene Oxide: Aerosol Synthesis And Environmental Applications, Yi Jiang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Environmental technologies, such as for water treatment, have advanced significantly due to the rapid expansion and application of nanoscale material science and engineering. In particular, two-dimensional graphene oxide (GO), has demonstrated considerable potential for advancing and even revolutionizing some of these technologies, such as engineered photocatalysts and membranes. To realize such potential, an industrially scalable process is needed to produce monomeric and aggregation-resistant GO nanostructures/composites, in addition to new knowledge of material properties, behavior, and performance within an environmental context.

Research presented in this thesis addresses both scientific and engineering gaps through the development of a simple, yet robust aerosol-based …

Application Of Voltammetry For Electroanalytical Measurement Of Concentrations In Lacl3-Mgcl2 Mixtures In Eutectic Licl-Kcl, Zhonghang Wang, Devin Rappleye, C S. Yang, Michael Simpson

Faculty Publications

For electroanalytical measurement of molten chloride salts, various voltammetry methods have been used on mixtures of MgCl₂ and LaCl₃ in eutectic LiCl-KCl. These salt mixtures are of primary interest to spent nuclear fuel electrorefining systems. MgCl₂ is used as a surrogate for PuCl₃, while LaCl₃ represents rare earth fission product salts. Cyclic voltammetry scans with these salt mixtures exhibited extra peaks, presumably due to underpotential deposition of La(III) ions onto Mg. Quantitatively, the current contribution from each peak was best determined using normal pulse voltammetry and fit to the Cottrell equation. This yielded linear …

Development And Characterization Of Oxygen Sensitive Microbial Biosensors, Jonathan Lee

Rose-Hulman Undergraduate Research Publications

Microbial biosensors are useful in detecting suboptimal conditions in a bioreactor. This detection can help in development of improved mixing methods to reduce the occurrence of these conditions. In this research, the activities of 3 promoters known to have activity under anaerobic conditions, the gadB promoter, an FNR protein activated promoter, and the pfl promoter, were tested for activity under anaerobic conditions by connecting them to a green fluorescent protein (GFP) gene. Using two types of media, Luria-Bertani (LB) and Wilms-Reuss media, the activity of these promoters under aerobic and anaerobic conditions were tested. Results indicate that while the FNR …

Amine-Thiol Solution Route Method For Fabricating Cdxzn1-Xs Thin Film Solar Cells, Preston D. Fernandez, Xianyi Hu, Carol Handwerker, Rakesh Agrawal

The Summer Undergraduate Research Fellowship (SURF) Symposium

Cadmium zinc sulfide, CdZnS, is a promising material for the buffer layer of thin film solar cells because the alloy is considerably more cost effective and more optimizable than pure cadmium sulfide, CdS, in terms of band gap. The current fabrication methods of the buffer layer often require expensive equipment or produce undesirable impurities in the alloy. This study investigates a cost effective and scalable solution route method to synthesize the CdZnS buffer layer. Molecular precursors of CdZnS were dissolved in varying molecular ratios of cadmium and zinc in a mixture of hexylamine and propanethiol. The resulting alloys produced were …

Hydrophobic Zeolites For Applications In Adsorption And Catalysis, Zige Huang, Michael Cordon, Rajamani Gounder

The Summer Undergraduate Research Fellowship (SURF) Symposium

Lewis acidic zeolites such as Sn-Beta are commonly studied for use as selective catalysts for glucose isomerization to fructose in liquid water. Glucose to fructose isomerization is a critical reaction for lignocellulosic biomass upgrading, which converts abundant and renewable feedstocks into commercially desirable fuels and chemicals.

Industrial applications require catalysts that maintain optimal reactivity over long time scales, yet at typical reaction temperatures, Lewis acidic Beta zeolites are known to deactivate in liquid water through poorly understood mechanisms. Recent work in our group has shown that interactions between water and Sn-Beta zeolites can cause leaching of active Sn sites from …

Exploring The Effects Of Aromatic Molecules In Chemical Enhanced Oil Recovery, Jacob M. Crain, Cliff Johnston, Rituraj Borgohain

The Summer Undergraduate Research Fellowship (SURF) Symposium

Chemical enhanced oil recovery (cEOR) methods are being used as a viable contributor to the world’s growing energy demands. Due to the complex chemical composition of crude oil, attempting to optimize the surfactant concentration and salinity of formulations is done empirically. This process can be very time intensive due to the wide variety of surfactant structures available for cEOR. Surfactant selection is typically done by matching the average chain length of the oil with that of the surfactant. In this study, we are trying to understand how aromatic structures present in Illinois Basin crude oil interact with surfactants. This will …

Continuous Ligand-Assisted Elution Chromatography Applied To Separation Of Rare Earth Elements, Jeremy A. Weinstock, David M. Harvey, N.-H. Linda Wang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Rare earth elements (REEs) are metals used to make many valuable products such as magnets and electronics. Following their extraction from larger materials, REEs are to be separated into their individual components as high purity is required for product manufacture. Purification is very difficult because most (15/17) of the REEs are lanthanides (Ln’s) and Ln ions have the same valence and similar atomic radii. The current industrial process for purifying REEs involves using toxic solvents to perform a series of liquid-liquid extractions. Ling and Wang (2015) proposed a ligand-assisted batch chromatography process to purify Ln’s. The latter approach is a …

Quantification And Characterization Of Aluminum Distributions In Commercial Beta And Mordenite Zeolites By Cobalt Exchange, Rebecca L. Reitzel, Claire T. Nimlos, Rajamani Gounder

The Summer Undergraduate Research Fellowship (SURF) Symposium

The aluminum distribution throughout the zeolite framework determines the structural, ion-exchange and catalytic properties of the zeolite. Several methods have been proposed to control the Al distribution, but in order to accurately assess these methods a procedure is needed to quantify Al distribution in various zeolite frameworks. Co²⁺ ions exchange onto the zeolite framework at Al pairs, and atomic absorbance spectroscopy (AAS) can be used to quantify the number of exchanged Co²⁺ ions and, in turn, the overall number of Al pairs. Each framework exhibits differences in pore size and channel configuration which affect the equilibrium conditions needed …

Production Of Porous Alginate Substrates Via Membrane Emulsification For Pharmaceutical Applications, Genesis D. Correa-Rivera, David A. Acevedo, Zoltan K. Nagy

The Summer Undergraduate Research Fellowship (SURF) Symposium

The Food and Drug Administration (FDA) released in 2013 a report that established the pharmaceuticals current good manufacturing practices for the 21^st century. This report encourages the creation of new technology in the pharmaceutical industry. Therefore, this research aims to develop a reliable method to produce porous polymers particles to be used in a novel continuous crystallization in porous substrate. The aim of the current work is to create porous polymer microspheres with uniform particle size distribution using a commercially available membrane emulsification system. In the present study, the emulsification was made using a dispersed phase composed of miglyol …