Chemical Engineering Commons^™

Garver Industrial Design Project: Designing A Full-Scale Reverse Osmosis Water Treatment Facility For The City Of Lawton, Oklahoma, Kayliana Warden, Marlando Collins, Sandrina Depaz, Reid Eakin, Reed Leasure, Vera Rodriguez

Chemical Engineering Undergraduate Honors Theses

A groundwater treatment facility was designed for Lawton, Oklahoma to address potential water scarcity due to drought conditions in southwest Oklahoma. The facility will produce five million gallons per day (MGD) of treated water. The plant will have the capacity of treating 4,085 gallons per minute of influent water at an 86% recovery. The water to be treated will come from the Arbuckle-Timbered Hills Aquifer. Studies have been conducted around the aquifer to identify the best well site locations.

A centralized treatment facility using reverse osmosis filtration as the main treatment technology has been designed. To prevent reverse osmosis membrane …

Predicting Henry's Law Constants Of Volatile Organic Compounds Present In Bourbon Using Molecular Simulations., Christopher A Abney

Electronic Theses and Dissertations

Henry’s Law describes the partitioning of molecules into liquid and gas phases at low concentrations. Henry’s Law, which is based upon a species-dependent constant and the gas phase partial pressure, is useful for predicting phase behavior of dilute solutes. However, Henry’s Law constants are difficult to measure experimentally or to predict using structure-property or thermodynamic models. Herein, molecular simulations were used to calculate Henry’s Law constants for 18 volatile organic compounds (VOCs) present in bourbon. The novel simulations analyzed solvation thermodynamics of small organic molecules in 120 proof ethanol. A fast-growth non-equilibrium free energy method was used in which the …

Detecting The Leakage In The Pipeline System Through Flow Parameter Analysis, Hao Fu

Theses and Dissertations

The pipeline is an efficient way to transport oil and gas over long distances. However, leakage can occur when the pipes have been running for a long time. The leak of energy resources will cause economic loss in millions of dollars, pollute the local environment, and result in safety problems. Therefore, the technology of pipeline leak detection is very crucial during the energy transport process.

The goals of the research are to develop mathematical models based on experimental data and CFD simulation to detect single and multiple leaks in a pipeline and/or pipeline system. The new methods use daily recorded …

Analysis Of Fluid Flow In Redox Flow Batteries, Erfan Asadipour

McKelvey School of Engineering Graduate Student Theses & Dissertations

Redox flow batteries (RFB) hold great potential for large-scale stationary energy storage. However, their low energy density compared to other energy storage systems must improve for feasibility. Electrolyte flow distribution affects current density distribution and providing a uniform current density distribution is one way to improve RFB performance. Additionally, reducing the power consumption of the electrolytes’ pump as a source of energy loss in RFB systems increases their efficiency. Investigating both subjects requires analysis of the fluid dynamics in RFB cells.

In this thesis, a novel, computationally cost-effective hydraulic-electrical analogous model (HEAM) was developed to study fluid dynamics by implementing …

Degradation Of Antibiotics In Aqueous Phase Using Pms Catalytic Decomposition With Zero-Valent Iron Nanoparticles Immobilized In Sba-15, Ahdee Bluma Zeidman

UNLV Theses, Dissertations, Professional Papers, and Capstones

Zero-valent iron nanoparticles (nZVI) have been studied as an option for soil remediation and water treatment for many years. The capability of nZVI to produce oxidation/reduction processes, depending on the reaction conditions, has attracted great interest with their major drawback being reactivity loss through agglomeration. The loss in nZVI surface area has been reported to be prevented through immobilization onto a porous media (e.g., SBA-15, MCM-41, or zeolites). In this work, a mesoporous silica structure (SBA-15) is used as an nZVI supporting material to enhance its reactivity and promote peroxymonosulfate (PMS) catalytic decomposition for the degradation of antibiotics in aqueous …

Image Analysis Of Charged Bimodal Colloidal Systems In Microgravity., Adam J. Cecil

Electronic Theses and Dissertations

Colloids are suspensions of two or more phases and have been topics of research for advanced, tunable materials for decades. Stabilization of colloids is typically attributed to thermodynamic mechanisms; however, recent studies have identified transport or entropic mechanisms that can potentially stabilize a thermodynamically unstable colloidal system. In this study, suspensions of silsesquioxane microparticles and zirconia nanoparticles were dispersed in a nitric acid solution and allowed to aggregate for 8-12 days in microgravity aboard the International Space Station. The suspensions were subsequently imaged periodically at 2.5x magnification. Due to the inadequacy of existing image analysis programs, the python package “Colloidspy” …

Annealing Of Encapsulated Heavy Metals From Brine Water Utilizing Microwave Enabled Sol-Gel Process, Adam Michael Flynn

Electronic Theses and Dissertations

Various waste encapsulation strategies have been investigated to solidify and stabilize heavy metal wastewater for proper long-term storage. This work aims to enhance a method of novel sol-gel encapsulation of heavy metals from mock brine waters using tetramethyl orthosilicate with the addition of an annealing step at various temperatures in order to reduce leaching of metals from the silica monoliths when exposed to water. The metals tested for encapsulation and leaching were mercury (II) chloride, potassium dichromate, sodium selenite, boric acid, cadmium chloride, and copper (II) acetate. The annealing of the silica monoliths led to an increased degree of for …

Heavy Oil And Vapex Process: A Brief Review, Vijitha Mohan, Parthasakha Neogi, Baojun Bai

Chemical and Biochemical Engineering Faculty Research & Creative Works

Heavy oil recovery requires either heat or solvent assistance to reduce its high viscosity first and then the less viscous oil can be recovered. Processes that use vapor assisted petroleum extraction (VAPEX) utilize vaporized solvent. Solvent vapors are introduced through a top injection well to induce viscosity reduction and the less viscous oil is collected at the bottom production well. It is noteworthy, that the solvent itself when recovered, can be seen as an integral part of oil. Exact molecular weight and chemistry of heavy oil is uncertain making analysis of thermodynamic properties difficult, however this is overcome by making …

In Vivo Analysis Of A Proprietary Glass-Based Adhesive For Sternal Fixation And Stabilization Using Rabbit And Sheep Models, Cina Mehrvar, Emily Deignan, Mark Hurtig, Gideon Cohen, Paul Zalzal, Oleg Safir, Adel Alhalawani, Marcello Papini, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Wire cerclage remains the standard method of care for sternal fixation, following median sternotomy, despite being beset with complications. An emerging treatment option has been to augment the wires with an adhesive. A patented ionomeric glass (mole fraction: SiO₂:0.48, ZnO:0.36, CaO:0.12, SrO:0.04) has been used to formulate GPC+, a glass polyalkenoate cement (GPC), by mixing it with poly(acrylic) acid (PAA) and de-ionized water. In a human cadaver study, this material, when applied with wire cerclage, was able to significantly reduce sternal instability. However, the material has yet to be tested in pertinent animal models. Here, after a series …

Peptoid-Based Microsphere Coatings For Biomaterial Applications, Jesse Leland Roberts

Graduate Theses and Dissertations

Peptoids are peptidomimetic oligomers that predominantly harness similarities to peptides for biomimetic functionality. The incorporation of chiral, aromatic side chains in the peptoid sequence allows for the formation of distinct secondary structures and self-assembly into supramolecular assemblies, including microspheres. Peptoid microspheres can be coated onto substrates for potential use in biosensor technologies, tissue engineering platforms, and drug-delivery systems. They have the potential for use in biomedical applications due to their resistance to proteolytic degradation and low immunogenicity. This dissertation focuses on the physical characteristics and robustness of the peptoid microsphere coatings in various physiological conditions, along with their ability to …

Surface Modified Polypropylene Membranes For Treating Hydraulic Fracturing Produced Waters By Membrane Distillation, Tharaka Hawpe Gamage

Graduate Theses and Dissertations

Membrane distillation is an emerging technology for treating hydraulic fracturing flowback and produced waters. Suppression of membrane fouling by inorganic and polar and non-polar organic compounds is a challenge. Here polyhydroxyethyl methacrylate, polyacrylic acid, polvinylallyl imidazolium bromide and polyvinylhexyl imidazolium bromide chains have been grafted from the membrane surface. Fouling is initially due to adsorption of organic compounds followed by scale formation. When challenged with produced water, membranes modified with polvinylallyl imidazolium bromide chains provided the greatest resistance to fouling. For EC pretreated produced water and synthetic produced water that contained mainly inorganic species, the flux decline was much less.

Investigative Study Of Microalgal And Electrochemical Wastewater Treatment Systems And Modeling Of The Wafer-Enhanced Electrodeionization Using Supervised Learning, Humeyra Betul Ulusoy Erol

Graduate Theses and Dissertations

Wastewater has a serious impact on environment and public health due to its high concentration of nutrients and toxic contaminants. Without proper treatment, excess nutrients discharged in wastewater can cause a damage to the ecosystem such as undesirable pH shifts, cyanotoxin production, and low dissolved oxygen concentrations.

Main objectives of this dissertation work were to investigate i) the biofuel potential of P. cruentum when grown in swine wastewater, ii) the influence of four most commonly used ion exchange resins on the system efficiency and selectivity for the removal of sodium, calcium, and magnesium ions, and iii) the modeling of wafer-enhanced …

Behavior Of Selective Oxygen Functional Groups Upon Hydrothermal Carbonization And Pyrolysis Of Biomass And Their Roles On Selective Applications, Nepu Saha

Theses and Dissertations

Hydrothermal carbonization (HTC) is a thermochemical process where biomass is treated in water under high temperature and corresponding vapor pressure. During HTC, biomass undergoes a series of reactions including hydrolysis, decarboxylation, dehydration, aromatization, and polymerization. As a result, a solid product is produced from biomass after HTC process, which is widely known as hydrochar. Depending on the HTC process conditions, a wide-variety of oxygen-containing groups formed on hydrochar surfaces. Many of these groups could play critical roles in applications such as adsorption, and energy and gas storage, etc. However, not all functional groups are exposed on the surface due to …

Comparison Of Tensile Properties Of Triaxial Braided Carbon Fiber Composites Made From Vacuum Assisted Resin Transfer Molding (Vartm) And Autoclave Molding, Donald A. Klosterman, Charles Browning

Chemical and Materials Engineering Faculty Publications

Triaxially braided fiber composites are increasingly being used in aerospace, ballistic, and sporting good applications due to their inherent damage tolerance, torsional stability, and cost compared to woven fabrics and unidirectional preforms. There have been numerous publications over the past 15-20 years on the mechanical properties and failure mechanisms of triaxial braided composites. However, most of these have involved panels made with autoclave curing. In the present study, braided carbon fiber composites were made using autoclave curing and vacuum assisted resin transfer molding (VARTM). The goal of the study was to compare the physical and tensile properties of quasi-isotropic panels …

Ceramic Tiles Production From Cullet And Agricultural Wastes Obtained From Wheat And Sugarcane Cultivation, Mai H. Roushdy

Chemical Engineering

Agricultural wastes are a big source for environmental pollution so it’s a good choice to recycle them so as to get an environmental and economic benefit. The purpose of this research is to determine the possibility of recycling two types of agriculture wastes obtained from wheat and sugarcane cultivation in addition to broken glass (cullet) as raw materials for ceramic wall tiles production. The used agriculture wastes are the agricultural residue obtained from wheat and sugarcane cultivation. The experimental work starts with performing XRF and sieve analysis for all raw materials. Ceramic wall tiles specimens were made with dimensions 110.4 …

Co2-Wettability Reversal Of Cap-Rock By Alumina Nanofluid: Implications For Co2 Geo-Storage, Muhammad Ali, Adnan Aftab, Faisal Ur Rahman Awan, Hamed Akhondzadeh, Alireza Keshavarz, Ali Saeedi, Stefan Iglauer, Mohammad Sarmadivaleh

Research outputs 2014 to 2021

The usage of nanofluids is vast in different applications of nano-energy. These minute nanoparticles can be used to alter the hydrophobicity into hydrophilicity for CO2-brine-mineral systems in the presence of organic acids. Nonetheless, the literature lacks the information for the behavior of nanoparticles and its associated concentrations in the presence of organic acids at the reservoir (high temperature and high pressure) conditions. In this study, we have investigated that how different alkyl chain organic acids impact the wettability of mica muscovite for different ageing times (7 days and one year) and how this impact can be reversed by nanofluid priming …

Design, Analysis, And Optimization Of A Process To Produce Dimethyl Ether From Methanol, Thomas Mathwig

Honors Theses

The company that the engineering team works for is facing a contract loss with one of its customers of methanol. To avoid economic losses, a process has been proposed for converting the unused methanol to dimethyl ether (DME) through a dehydration reaction. After a preliminary simulation of the base case and optimization of the distillation column, an Equivalent Annual Operating Cost (EAOC) of $140,000 was calculated for the column. The EAOC was the sum of the annualized capital investment and the annual operating cost. Determining the process to be worth pursuing, a Toller was brought in to provide rental equipment …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Student Research Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

Recovery Of Degraded Lithium Ion Cathode Particles, James Kirtley

Undergraduate Research Conference at Missouri S&T

This project focuses on recovering the cathode materials of lithium ion batteries through atomic layer deposition (ALD) thin film coating. In industry, when a cathode material for a lithium ion battery are stored, it reacts with CO2 and moisture in the air creating Li2CO3 and LiOH on the particle surface. The harmful substances on the surfaces have a negative impact on battery performance and battery life. In this study, we found that when Li2Ni0.8Mn0.1Co0.1 (Ni-Rich NMC) is exposed to a high amount of moisture it degrades and the performance is reduced. For example, the discharge capacity of Degraded Ni-Rich NMC …

Effects Of Sleep Deprivation On Learning In Fruit Flies, Natalie Gardner

Undergraduate Research Conference at Missouri S&T

The fruit fly Drosophila Melanogaster is an optimal research specimen when observing the effects of sleep deprivation on spatial learning. A fly's sleep can be tracked using locomotion while it is undisturbed and while it undergoes sleep deprivation. To measure a fly's visuospatial awareness, a region at a comfortable 24 degrees Celsius, among the rest of the arena yielding an uncomfortable temperature ranging from 36-37 degrees Celsius, is fit with a specific visual cue that the fly is able to identify. This region, along with it's visual cue, is rotated around the arena every 3 minutes, and the amount of …