Application Of Thin Film Analysis Techniques And Controlled Reaction Environments To Model And Enhance Biomass Utilization By Cellulolytic Bacteria,
2012
University of Kentucky
Application Of Thin Film Analysis Techniques And Controlled Reaction Environments To Model And Enhance Biomass Utilization By Cellulolytic Bacteria, Hsin-Fen Li
Theses and Dissertations--Chemical and Materials Engineering
Cellulose from energy crops or agriculture residues can be utilized as a sustainable energy resource to produce biofuels such as ethanol. The process of converting cellulose into solvents and biofuels requires the saccharification of cellulose into soluble, fermentable sugars. However, challenges to cellulosic biofuel production include increasing the activity of cellulose-degrading enzymes (cellulases) and increasing solvent (ethanol) yield while minimizing the co-production of organic acids. This work applies novel surface analysis techniques and fermentation reactor perturbations to quantify, manipulate, and model enzymatic and metabolic processes critical to the efficient production of cellulosic biofuels.
Surface analysis techniques utilizing cellulose thin film …
Microemulsion Preparation And Electrochemical Characterization Of Pt/C, Ptir/C Electrocatalysts,
2011
Institute of Fuel Cell, Shanghai Jiao Tong University, Shanghai 200240, China
Microemulsion Preparation And Electrochemical Characterization Of Pt/C, Ptir/C Electrocatalysts, Ya-Ping Zeng, Sheng Sui
Journal of Electrochemistry
The Pt/C electrocatalysts were prepared by three different systems and the PtIr/C electrocatalysts were prepared with four different Ir contents. The samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), cyclic voltammetry (CV), potentiostatic and potentiodynamic polarizations measurements. The experimental results confirmed that the electrocatalyst particles prepared by the microemulsion method were well distributed on XC-72R supports with the active particle sizes of 5～10nm and good electrocatalysts activity. The Pt85Ir15/C electrocatalysts showed the highest overall electrochemical activity in unitized regenerative fuel cell.
Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2O2 On Gew11Co/P-Opd/Gc Electrode,
2011
Institute of Environmental and Analytical Sciences, College of Chemistry and Chemical Engineering, Henan liniversity, Kaifeng 475004, Henan, China
Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2O2 On Gew11Co/P-Opd/Gc Electrode, Li-Li Zhu, Jian-Ying Qu, Jue Wang, Hao-Yue Feng
Journal of Electrochemistry
The electrochemical properties of Co-substituted trimeric tungstogermanate containing Keggin fragments were studied. Cyclic voltammograms revealed two couples of reversible redox peaks on glassy carbon (GC) electrode in acid solutions. They corresponded to two-electron reductions accompanying by the additions of four protons and three protons, respectively, both were controlled by adsorption. The differences in the peak potentials of 2-electron-4-proton and 2-electron-3-proton reactions were 31 mV and 35 mV, respectively..Furthermore, the tungstogermanate (GeW11Co) modified GC electrode with functionalization by poly(o-phenylenediamine) (P-oPD) was prepared readily by electropolymerization. The GeW11Co/P-oPD/GC electrode could electrocatalyze the reduction of hydrogen peroxide, which showed good stability and quick …
Preparation And Characterization Of The Lani0.6Fe0.4O3-δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell,
2011
Institute of Fuel Cell, School of Mechanical Engineering, Shanghai jiaotong lniversity, Shanghai 200240,China
Preparation And Characterization Of The Lani0.6Fe0.4O3-δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell, Hang Liu, Bo Huang, Xin-Jian Zhu
Journal of Electrochemistry
The LaNi0.6Fe0.4O3-δ as cathode material for intermediate temperature solid oxide fuel cell was prepared using a combustion synthesis technique. The X-ray diffraction (XRD) pattern showed that the single-phase LaNi0.6Fe0.4O3-δ perovskite could be obtained after heat treatment at 600°C. The TEM and SEM images of the synthesized powders revealed that the grains were 50-100nm. According to the electrochemical impedance spectra (EIS), the polarization resistance of the symmetric cell LaNi0.6Fe0.4O3-δ/ScSZ/LaNi0.6Fe0.4O3-δ sintered at 1050°C was the smallest (0.70Ω·cm2, 0.27Ω·cm2 …
Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell,
2011
Chongqing Automobile college, Chongqing University of Technology,Chongqing, 400054,China;
Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell, Qiu-Hong Jia, Ming Han, Bin Deng, Cai-Zhi Zhang
Journal of Electrochemistry
In this paper, a dynamic model of PEMFC is developed to estimate the dynamic performance of PEMFC by analyzing in detail the influence factors of voltage of PEMFC including various losses. The partial pressure of hydrogen and oxygen is obtained using the differential form of the ideal-gas equation in this model. The steady-state model is obtained by setting reasonable parameter values. The simulation results and experimental results have good consistency, which shows that the simulation model is correct, reasonable and effective. It analyzed the dynamic response characteristics of the output voltage and the partial pressure of hydrogen in condition of …
Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System,
2011
Key Laboratory of Scienee & Technology of Eco-Textile, Ministry of Education, Donghua Unversity, Shanghai 201620, China
Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System, Qing-Zhi Wang, Wei Wang
Journal of Electrochemistry
The electrochemical behavior and possible reaction mechanism in Fe(Ⅲ)-oxalate-calcium gluconate system were studied by cyclic voltammetry. The results showed that Fe(Ⅱ)-gluconate was the final reductant. The reduction time, the working voltage and the cathode area influenced the current efficiency. The high current efficiency of 89% for the indirect electrochemical reduction of Vat Scarlet R could be achieved with reduction time of 10 min, working voltage of 4 V and cathode area of 40 cm2 in Fe(Ⅲ)-oxalate-calcium gluconate system.
Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure,
2011
College of Petrochemical Technology, Lanzhou University of Technology, Lanzhou 730050, China
Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure, Hui Xu, Zhen-Jun Peng, Dong-Hong Guo, Jun-Ling Li
Journal of Electrochemistry
The mesh-like structure of NiO electrode was obtained by first preparing the precursors via hydrothermal process using nickel sulfate and carbamide as reactants, sodium hexametaphosphate as a surfactant, and followed by calcination of the precursors at 400 ℃. The structure, morphology and capacitance characteristics of NiO electrode were characterized by XRD, SEM and constant current charge-discharge testing techniques. The effects of hydrothermal temperatures on the electrochemical properties of NiO electrode were investigated. The results showed that the better property of nickel oxide was obtained when the mole ratio of nickel to urea was 1:4 and the hydrothermal temperature was 140℃. …
Evaluation Of Cathode Materials For Low Temperature (500-700c) Solid Oxide Fuel Cells,
2011
University of Connecticut - Storrs
Evaluation Of Cathode Materials For Low Temperature (500-700c) Solid Oxide Fuel Cells, Alexander M. Lassman
Master's Theses
Solid oxide fuel cells (SOFC) have gained a great deal of interest, due to their potential for high efficiency power generation and ability to utilize hydrogen fuel, as well as various hydrocarbon-based fuels. A recent trend in SOFC development has been towards lower operating temperatures (500-700°C), which can substantially reduce the cost and complexity of the system. This thesis presents an investigation into state of the art Ba- and La- based cathode materials for use in low temperature (500-700°C) solid oxide fuel cells.
Synthesis of A-site deficient [A=0.97] Ba0.5Sr0.5Co0.8Fe0.2O3 (BSCF) was …
Electrochemical Performance Of Tin Dioxide/Carbon Xerogel Composites As Anode Materials For Lithium-Ion Batteries,
2011
State Key Laboratory of Physical Chemistry of Solid Surfaces, Department of Chemistry,College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005, Fujian, China;
Electrochemical Performance Of Tin Dioxide/Carbon Xerogel Composites As Anode Materials For Lithium-Ion Batteries, Xiao-Jing Liu, Lin-Lin Qin, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong
Journal of Electrochemistry
The tin dioxide/carbon xerogel composites were synthesized by using vacuum infiltration method. Structural characterization and morphology of the composites were investigated by using XRD, TEM and SEM techniques. BET test was performed to determine the pore size distributions of carbon xerogels and the composites. The results showed that the nano-sized SnO2 particles (5~10 nm) were encapsulated in the pores of carbon xerogels. During the electrochemical tests the SnO2 in the composites exhibited capacity retention of 61.9% after 100 cycles of charge-discharge tests at 100 mA/g.
Synthesis Of Limnpo4/C Used As Cathode Material For Lithium Ion Batteries,
2011
Dalian University of Technology School of Chemical Engineering School of Petrochemical Engineering, Dalian,116024;
Synthesis Of Limnpo4/C Used As Cathode Material For Lithium Ion Batteries, Xin Yang, Xue-Wu Liu, Gui-Chang Liu, Zhi-Cong Shi, Xin Li, Guo-Hua Chen
Journal of Electrochemistry
The LiMnPO4/C composites were prepared using a solid-state reaction with addition of the resorcinol formaldehyde resin as the carbon source. The effects of reaction temperature and time on the crystal structure, morphology and electrochemical properties of the LiMnPO4/C composites were investigated. The results show that the best performance was achieved with the LiMnPO4/C composites synthesized at 600 oC for 12 h which had the particle sizes about 100~200 nm. The initial discharge capacities were 121.6 mAh·g-1 at 0.02C, 110 mAh·g-1 at 0.1C and more than 60 mAh·g-1 at 1C. An …
Synthesis And Electrochemical Behaviors Of Li2Coxmn1-XSio4 As A Cathode Material For Lithium-Ion Batteries,
2011
State Key Laboratory of Physical Chemistry of Solid Surfaces , College ofChemistry and ChemicalEngineering,Xiamen University, Xiamen 361005,Fujian, China
Synthesis And Electrochemical Behaviors Of Li2Coxmn1-XSio4 As A Cathode Material For Lithium-Ion Batteries, Lin Wang, Dong-Ping Lv, Yong Yang
Journal of Electrochemistry
We have successfully synthesized Li2CoxMn1-xSiO4/C (x=0, 0.1, 0.3, 0.5, 1)/C composites using hydrothermal assisted sol-gel process and ball-milling method. The results of X-ray diffraction show that the solid solutions of Li2CoxMn1-xSiO4 can be achieved when x≤0.3. The initial capacities increase from 70 mAh·g-1 of Li2MnSiO4/C to 105 mAh·g-1 of Li2Co0.3Mn0.7SiO4/C. Cyclic Voltammetry (CV) curves show that the replacement of Mn with Co can reduce the electrochemical polarization, making the insertion-extraction reaction …
Applied Control Strategies At A Cogeneration Plant,
2011
University of Connecticut
Applied Control Strategies At A Cogeneration Plant, Joseph William Burns
Master's Theses
The purpose of this paper is to demonstrate the effectiveness of “classical strategies for dynamic control” on authentic cogeneration processes. These strategies are applied to several processes at the University of Connecticut’s cogeneration plant. Case studies of their applications are presented in this paper. Strategies that are applied include the following:
1) The classical SISO feedback structure
2) The First Order Plus Dead Time (FOPDT) process model
3) The Internal Model Control (IMC) correlations for PI controller tuning
4) Static feed forward with feedback trim
5) Cascade Control
Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals,
2011
1. Department of Chemistry, Xinzhou Teachers’ University, Shanxi Xinzhou 034000, China; 2.Department of Chemistry, Beijing Normal University, Beijing 100875, China;
Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan
Journal of Electrochemistry
A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H2O2 with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …
Preparation And Electrocatalytic Activity Of The Pt/Wc/Tio2 Composites,
2011
State Key Laboratory Breeding Base of Green Chemistry Synthesis Technology, College ofChemicalEngineering and Materials Seience, Zhejiang University of Technology, Hangzhou 310032, China
Preparation And Electrocatalytic Activity Of The Pt/Wc/Tio2 Composites, Chun-An Ma, Bin Yu, Mei-Qin Shi, Xiao-Ling Lang
Journal of Electrochemistry
TiO2 was used as the support for preparation of Pt/WC/TiO2 composite catalyst. The composites were characterized by XRD, SEM and TEM methods. The electrocatalytical activity of Pt/WC/TiO2 composite for oxidation of methanol was investigated by cyclic voltammetry. Pt/WC/TiO2 exhibited higher activity compared with that of Pt/TiO2 and Pt/WC composite catalysts. Based on this we discussed the effects of crystal phases of TiO2 on the electrocatalytical activity of Pt/WC/TiO2 composite catalyst.
Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces,
2011
2. College of Chemistry and Chemical Engineering, Hunan University of Arts and Science, Changde 415000 Hunan, China
Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces, Li-Hui Ou, Sheng-Li Chen
Journal of Electrochemistry
CO2 reduction on Cu(111) single crystal surfaces was studied using DFT calculations on the reaction energies and the minimum energy paths. The results indicated that the possible reaction paths for CO2 reduction on Cu(111) surface are CO2(g) + H* → COOH* → (CO +OH)*, (CO + H)* → CHO*, CHO + H → CH2O* → (CH2+O)*, CH2* + 2H* → CH4 or 2CH2* → C2H4. On Cu(111) surface, the reaction rate is controlled by steps of CH2O* → (CH2 …
Anode Electrodeposition Of Ti/Mno2 Electrode And Electrocatalytic Oxidization Properties Of Phenol Degradation,
2011
College of Materials Science and Chemical Engineering, Harbin Engineering University, Harbin150001, Heilongjiang, China
Anode Electrodeposition Of Ti/Mno2 Electrode And Electrocatalytic Oxidization Properties Of Phenol Degradation, Ye Chen, Wen-Li Zhao, Qing Wen
Journal of Electrochemistry
Ti-base manganese dioxide (Ti/MnO2) electrode was prepared by anodically electrodeposition technology in this paper. The structure of the electrode, the microstructure of the electrode surface and the element composition of the electrode were analyzed by XRD, SEM and EDS. The preparation process parameters of the electrode were studied in detail with the help of the V~logi curve and phenol degradation curve. The Ti/MnO2 electrode was anodically electrodeposited at current density 4mA•cm-2, the Mn2 + ions concentration 0.5mol•L-1 and temperature70℃. The V~logi curve and phenol degradation curve were used to evaluate electrocatalytic oxidization properties …
Electrochemical Capacitive Performance Of Mesoporous Carbon Based Co-Ni Oxides,
2011
1. State Key Laboratory of Gansu Advanced Non-ferrous Metal Materials, Lanzhou University of Technology, Lanzhou 730050, China;
Electrochemical Capacitive Performance Of Mesoporous Carbon Based Co-Ni Oxides, Zhen-Sheng Yang, Ling-Bin Kong, Li Deng, Yong-Chun Luo, Long Kang
Journal of Electrochemistry
By using defects on the surface of CMK-3 served as nucleation center, Co0.25Ni0.75 oxide/C composite was successfully prepared through a simple chemical co-precipitation method. Characterization was carried by using X-ray diffraction, BET and scanning electron microscopy. Results showed that a perfect mesoporous network of interconnected nanoflakes was obtained for Co0.25Ni0.75 oxide/C composite and, this material has a less crystallization, interconnected nanoflakes network structure and a narrow mesoporous distribution at about 3~4 nm. The highly dispersed and loosely packed Co0.25Ni0.75 oxide/C composite possessed good electrochemical accessibility and fast diffusion rate of OH …
Study On Direct Electro-Oxidation Of Anisaldehyde,
2011
College of Chemical Engineering and Materials Science of Zhejiang University of Technology, State Key Laboratory Breeding Base of Green Chemistry, Zhejiang University of Technology, Hangzhou 310032, Zhejiang,China;
Study On Direct Electro-Oxidation Of Anisaldehyde, Lin-Lin Wu, Ying-Hong Zhu, Shan-Shan Li, Hong-Yan Zeng, Chun-An Ma
Journal of Electrochemistry
The oxidation of anisole on Pt electrode was investigated by cyclic voltammery and constant potential electrolysis. The influence of scan rates, substrate concentration, supporting electrolytes and solvent were considered . The results show that the electro-oxidation process of anisole was irreversible. In this research the sulfuric acid was the best supporting electrolytes and acetone was the best solvent, and the process was controlled by diffusion . The product of constant potential electrolysis was charactered by GC-MS .The results show that the main products was anisaldehyde, and the selectivity was up to 66.5% when using acetone as solvent.
Comparison Of Catalytic Performance On Different Materials Supported Pd Catalysts For Formic Acid Oxidation,
2011
1. College of Material Science and Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, P.R.China
Comparison Of Catalytic Performance On Different Materials Supported Pd Catalysts For Formic Acid Oxidation, Su-Dong Yang, Yan-Yu Liang, Zhu-Liang Wen, Qi-Jun Song, Xiao-Gang Zhang
Journal of Electrochemistry
Graphite oxide (GO) was prepared from by Hummers method. Then the graphene nanosheets supporting Pd catalysts were prepared by a single-step chemical reduction method. The electrocatalytic performance for formic acid oxidation of the prepared Pd/graphene composite was studied as an electrode material in comparison with the composite catalysts based on the other carbons (MWCNTs, SWCNTs, and Vulcan XC-72 carbon black). X-ray diffraction (XRD) and transmission electron microscopy (TEM) measurements indicated that the Pd nanoparticles were well dispersed on the surface of the graphene nanosheets with a small particle size. The electrocatalytic oxidation of formic acid was studied by electrochemically active …
Synthesis Of Mesoporous Nickel Oxide For Supercapacitor Application,
2011
School of Chemistry and Chemical Engineering,Key Laboratory of Analytical Chemistry for Life Science(MOE),Nanjing University,Nanjing 210008,China;
Synthesis Of Mesoporous Nickel Oxide For Supercapacitor Application, Xuan-Xuan Chen, Zhen-Zhen Zhao, Deng-Chao Wang, Zhong-Jie Huang, Wen-Bin Ni, Li Yu, Jian-Wei Zhao
Journal of Electrochemistry
Mesoporous nickel oxide has been synthesized by calcining metal-organic coordination precursor.Transmission electron microscopy and BET test showed that the prepared NiO had a regular morphology and displayed a narrow size distribution.Electrochemical tests revealed that such mesoporous NiO had a specific capacity of 72 F·g-1 at the current of 2.0 A·g-1.Futhermore,the material showed excellent cycle-life stability.There was no degradation of capacitance after 1000 cycles.
