Aerospace Engineering Commons^™

Nucleotide Detection Mechanism And Comparison Based On Low-Dimensional Materials: A Review, M. Mustafa Azeem, Muhammad Shafa, Muhammad Aamir, Muhammad Zubair, Basma Souayeh, Mir Waqas Alam

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The recent pandemic has led to the fabrication of new nucleic acid sensors that can detect infinitesimal limits immediately and effectively. Therefore, various techniques have been demonstrated using low-dimensional materials that exhibit ultrahigh detection and accuracy. Numerous detection approaches have been reported, and new methods for impulse sensing are being explored. All ongoing research converges at one unique point, that is, an impetus: the enhanced limit of detection of sensors. There are several reviews on the detection of viruses and other proteins related to disease control point of care; however, to the best of our knowledge, none summarizes the various …

Media Streaming In A High-Rate Delay Tolerant Network, Kyle Vernyi

Williams Honors College, Honors Research Projects

Audio and video streaming across delay tolerant networks are relatively new phenomena. During the Apollo 11 mission, video and audio were streamed directly back to Earth using fully analog radios. This streaming capability atrophied over time. The gradual conversion to digital electronics contributed greatly to this. Additionally, 21st century space systems face the new requirement of interconnectedness. Delay Tolerant Networking (DTN) attempts to solve this requirement by uniting traditional point to point links into a robust and dynamic network. However, DTN implementations present bottlenecks due to low performance. High-Rate Delay Tolerant Networking (HDTN) is a performance-optimized DTN implementation. This work …

Induced Drag Laboratory Curriculum With Variable Aspect Ratio Wing, Alexander Milligan, Elizabeth Plyler

Williams Honors College, Honors Research Projects

A laboratory curriculum for undergraduate students at The University of Akron enrolled in 4600:413 Introduction to Aerodynamics was created to allow students a hands-on opportunity to study the basic fundamentals of aerodynamically induced drag. To accomplish this, a 3D printed wing was created with variable aspect ratio. This wing is to be utilized in the laboratory experiment in The University of Akron subsonic wind tunnel to generate data on lift on drag at different airspeeds, angles of attack, and aspect ratios. The laboratory curriculum provides basic theory applicable to the wind tunnel experiments as well as question prompts and data …

Experimental Study For Improving The Productivity Of Laser Foil Printing, Tunay Turk, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This Study Aims to Improve the Productivity of Laser Foil Printing (LFP), Which is a Foil-Based Metal Additive Manufacturing (AM) Process. LFP Uses a Dual-Laser System to Fabricate a 3-Dimensional Part in a Layered Fashion by Performing Four Steps in Each Layer: Spot Welding, Pattern Welding, Contour Cutting, and Edge Polishing, All of Which Performed by Use of Lasers. We Experimentally Examined the Welding and Polishing Steps in This Study to Enhance LFP Productivity. the Jump Speed, Dwelling Duration, and Weld Path of Spot Welding and the Line Welding Speed and Wait Time between Weld Lines of Pattern Welding Are …

Mixed-Input Learning For Multi-Point Landing Guidance With Hazard Avoidance Part Ii: Learning-Based Guidance Algorithm, Sixiong You, Chaoying Pei, Vinay Kenny, Ran Dai, Jeremy R. Rea

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper investigates the three-dimensional (3D) multi-point landing guidance (MLG) problem with hazard avoidance by developing a mixed-input learning-based method to achieve precise and fuel-efficient planetary landing in future Mars missions. Specifically, we aim to find a safe, fuel-efficient landing point and generate a fuel-optimal trajectory simultaneously in real-time. First, by introducing binary variables, the MLG problem is formulated as an optimal control problem with quadratic constraints. Then, by formulating the Hamiltonian function, the necessary conditions of optimality for the MLG problem are obtained, where the critical parameters are identified to represent the complete optimal solution. After that, to find …

Artificial Intelligence-Enabled Exploratory Cyber-Physical Safety Analyzer Framework For Civilian Urban Air Mobility, Md. Shirajum Munir, Sumit Howlader Dipro, Kamrul Hasan, Tariqul Islam, Sachin Shetty

VMASC Publications

Urban air mobility (UAM) has become a potential candidate for civilization for serving smart citizens, such as through delivery, surveillance, and air taxis. However, safety concerns have grown since commercial UAM uses a publicly available communication infrastructure that enhances the risk of jamming and spoofing attacks to steal or crash crafts in UAM. To protect commercial UAM from cyberattacks and theft, this work proposes an artificial intelligence (AI)-enabled exploratory cyber-physical safety analyzer framework. The proposed framework devises supervised learning-based AI schemes such as decision tree, random forests, logistic regression, K-nearest neighbors (KNN), and long short-term memory (LSTM) for predicting and …

An Insight Into The Effect Of Sharp And Round Edges On The Flow Field-A Cfd Simulation, Abid Hussain, Gao Puzhen, M. Mustafa Azeem, Muhammad Zubair, Muhammad Aamir, Muhammad Irfan Khaleed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents a numerical investigation of pressure drop and distribution in a channel around a sharp edge and a disc that is connected to the base of a circular rod. We have employed computational fluid dynamics (CFD)-Fluent for the validation of our models. It was found that the edge sharpness of the disc influences the pressure drop., i.e. sharp edge has higher turbulence and pressure drop. We also observed that pressure drops in the case of the circular disc are less than that of the sharp edge. However, pressure drop has essentially the same values for both shapes after …

Assessing The Performance Of A Particle Swarm Optimization Mobility Algorithm In A Hybrid Wi-Fi/Lora Flying Ad Hoc Network, William David Paredes

UNF Graduate Theses and Dissertations

Research on Flying Ad-Hoc Networks (FANETs) has increased due to the availability of Unmanned Aerial Vehicles (UAVs) and the electronic components that control and connect them. Many applications, such as 3D mapping, construction inspection, or emergency response operations could benefit from an application and adaptation of swarm intelligence-based deployments of multiple UAVs. Such groups of cooperating UAVs, through the use of local rules, could be seen as network nodes establishing an ad-hoc network for communication purposes.

One FANET application is to provide communication coverage over an area where communication infrastructure is unavailable. A crucial part of a FANET implementation is …

Development Of A Mission Design Tool For Computing Libration Point Formations Using Differential Corrections Initialized With A Genetic Algorithm, Donna Jennings

Doctoral Dissertations

"The growing interest in deep space spacecraft missions and distributed spacecraft formations has established the need for state-of-the-art advancements in the areas of relative dynamics and mission design. The focus of this research is to develop methods for identifying natural (i.e. ballistic) relative formation trajectories in the vicinity of the collinear libration points. A natural formation decreases the station keeping costs, lowering the consumption of spacecraft resources and extending mission lifetime. This research adapts both numerical and machine learning approaches to the problem of mission design. A genetic algorithm was first used to identify a multi-agent spacecraft formation in the …

Design Of An Internal Osculating Waverider Intake, Mark E. Noftz, Andrew J. Shuck, Joseph S. Jewell, Jonathan Poggie, Andrew N. Bustard, Thomas J. Juliano, Nicholas J. Bisek

Publications

The design of an inward-turning, high-speed, three-dimensional streamline traced intake is presented from osculating axisymmetric theory. To satisfy the osculating intake design criteria, a stitched Busemann diffuser and Internal Conical Flow-A solution is used as the basic isentropic compressive streamline. This new contour provides efficient compression, high flow uniformity, and straight leading edge shocks of equal strength. Additionally, a novel method for constructing the inlet cowl is presented. The combined process leads to a new method of high-speed intake design. A generic shape-transitioned intake is constructed and named the Indiana Inlet for the Indiana universities that contributed to the project. …

Tailoring A System Engineering And Management Plan For A University Satellite Team, Jacob D. Anderson

Masters Theses

"A Systems Engineering and Management Plan (SEMP) helps enable a successful engineering project or team. All university teams working on satellite development encounter similar obstacles that are not commonly seen in industry. As a result, university teams must determine new approaches to solve these unique and difficult problems. A SEMP can mitigate risks, solve problems, and provide streamlined solutions. A modified SEMP is proposed along with guidance for implementing it into a new team and an existing team.

The adopted SEMP provides a road map for the technical execution and program management of a university team. The SEMP should be …

Topologically Optimized Electrodes For Electroosmotic Actuation, Jianwen Sun, Jianyu Zhang, Ce Guan, Teng Zhou, Shizhi Qian, Yongbo Deng

Mechanical & Aerospace Engineering Faculty Publications

Electroosmosis is one of the most used actuation mechanisms for the microfluidics in the current active lab-on-chip devices. It is generated on the induced charged microchannel walls in contact with an electrolyte solution. Electrode distribution plays the key role on providing the external electric field for electroosmosis, and determines the performance of electroosmotic microfluidics. Therefore, this paper proposes a topology optimization approach for the electrodes of electroosmotic microfluidics, where the electrode layout on the microchannel wall can be determined to achieve designer desired microfluidic performance. This topology optimization is carried out by implementing the interpolation of electric insulation and electric …

Comparison Of Dynamics Stability Testing Techniques With Magnetic Suspension Wind Tunnel Capabilities, Otoniel A. Ramirez, Mark Schoenenberger, David E. Cox, Colin P. Britcher

Mechanical & Aerospace Engineering Faculty Publications

Dynamic stability testing techniques currently utilized at NASA Langley Research Center (LaRC) are conducted in multiple facilities and consists of free flight, forced oscillation, and free-to-oscillate tests. The NASA/ODU Magnetic Suspension and Balance System (MSBS) has been recommissioned to explore its utility as an additional facility to expand the dynamic stability test capabilities currently available at NASA LaRC. Simulations were created to replicate each current test facility and method as closely as possible. Data collected from the simulated environments was corrupted with replicated noise sources of the different testing environments and then compared to real data collected during tests when …

Patch-Wise Training With Convolutional Neural Networks To Synthetically Upscale Cfd Simulations, John P. Romano, Alec C. Brodeur, Oktay Baysal

Mechanical & Aerospace Engineering Faculty Publications

This paper expands the authors’ prior work[1], which focuses on developing a convolutional neural network (CNN) model capable of mapping time-averaged, unsteady Reynold’s-averaged Navier-Stokes (URANS) simulations to higher resolution results informed by time-averaged detached eddy simulations (DES). The authors present improvements over the prior CNN autoencoder model that result from hyperparameter optimization, increased data set augmentation through the adoption of a patch-wise training approach, and the predictions of primitive variables rather than vorticity magnitude. The training of the CNN model developed in this study uses the same URANS and DES simulations of a transonic flow around several NACA 4-digit airfoils …

Model Based Systems Engineering With A Docs-As-Code Approach For The Sealion Cubesat Project, Kevin Chiu, Sean Marquez, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

The SeaLion mission architecture team sought to create a model-based systems engineering approach to assist improving CubeSat success rates as well as for the SeaLion CubeSat project to guide an implementation for the flight software. This is important because university CubeSat teams are growing in number but often have untrained students as their core personnel. This was done using a document-as-code, or docs-as-code, approach. With this the team created tools for the systems architecture with the Mach 30 Modeling Language to create an architecture that is easy to learn and use even for newly admitted team members with little to …

Exploring Additive Manufacturing In A Space Environment - A Capstone Design Project Experience, Zain Zafar Khan, Zachary Alan Sobelman, Sharanabasaweshwara Asundi

Mechanical & Aerospace Engineering Faculty Publications

The employment of additive manufacturing in the non-standard environments like space, ships, or submarines has the potential to be an advanced utility not only in the pre-flight production of aerospace components and structures, but also for the onboard manufacturing of components and tools necessary for future space missions. For example, the ability to produce tools and structural components on the International Space Station can provide the space community the opportunity to make repairs and upgrades to the space station without wasting time and resources transporting such materials through additional missions. Additive manufacturing would allow for space missions to use on …

Alternatives To Reducing Aviation Fuel-Burn With Technology: Fully Electric Autonomous Taxibot, Denzil Neo

Student Works

Aircraft taxiing operations in the aerodrome were identified to consume the most jet fuel apart from the cruise phase of the flight. This was also well supported by various research associating taxi operations at large, congested airports, with high jet fuel consumption, high carbon emissions, and noise pollution. Existing literature recognised the potential to address the environmental issues of aerodrome taxi operations by operating External or Onboard Aircraft Ground Propulsion Systems (AGPS). Designed to power aircraft with sources other than their main engines, external Aircraft Ground Power Systems (AGPS) have shown the potential to significantly cut jet fuel consumption and …

Noise Reduction Techniques In Commercial Aircraft Cabins, Hashem Hashem

Student Works

Main sources of noise heard inside an aircraft cabin:

• Engines
• Airframe & control surfaces
• Window vibrations
• Passenger announcements & activities.

Microstrip Antenna Design Using Cst Optimized By Neural Network Algorithm, Hadeer. A Shoeab, Mohamed A.Mohamed, Marzouk El Said A, Ahmed. A. Kabeel

Mansoura Engineering Journal

In this paper, a general design procedure is suggested for the microstrip antennas using artificial neural networks and this is demonstrated using the rectangular patch geometry. The model was analyzed for 1733 data sets of input output parameters. 1300 samples for training and 433 samples for testing and 1500 epoch, learning rate from (0.003 to 0.005). Python was used to create and implement the ANN algorithm model. The mean error in detection of resonance frequencies (return loss peaks) was 0.144GHz on train set, and 0.116GHz on test set. The outputs of the radial basis function are optimized by varying the …

Strategies Aircraft Manufacturing Organizational Leaders Use For Proper Material Pricing, Chin Kuei Jen

Walden Dissertations and Doctoral Studies

The lack of proper material pricing strategies can challenge manufacturers’ profitability and growth. Aircraft manufacturing leaders are concerned because understanding and developing material pricing strategies are essential to increasing profitability. Grounded in price theory, the purpose of this qualitative single case study was to explore strategies aircraft manufacturing organizational leaders use for proper material pricing estimates. The participants were four aircraft manufacturing organizational leaders from a successful aircraft manufacturing business located in the state of Georgia. Data were gathered from semistructured interviews and document reviews and analyzed using Yin’s five step approach. The four themes that emerged were the impact …