Engineering Commons^™

Conceptual Design Of Fuel Dumping System In Aircraft, Naveen M. Kumar Mr., Ravi A. Kannan Be., Magesh L Be., Praveen T. Kumar Be., Vijay K. Babu Me., Prashanth Radhakrishnan Be.

International Journal of Aviation, Aeronautics, and Aerospace

Airlines release the unburned jet fuel into the atmosphere to reduce the weight of aircraft before landing. Sometimes, aircraft reach a weight more than takeoff weight while departing from the airport. Therefore, the pilot follows the ATC comment to dump fuel into the atmosphere to reduce the aircraft's weight to avoid accidents. Due to fuel dumping, an airline faces fuel consumption, loss, and several diseases affect environmental pollutants, and living things. The total fuel consumption of commercial airlines worldwide in 2021 is 57 billion gallons. If jet fuel routinely hit the ground, it would pollute water and land and damage …

Space Harpoon Projectile Analysis For Space Debris Capture, Miraj D. Lathia, Sam M. Dakka Dr

International Journal of Aviation, Aeronautics, and Aerospace

Space debris will become a more prevalent issue in this decade as technological advancements and greater dependencies on communications require more satellites in orbit, with some companies already hosting mega-constellations. Mitigating the debris using a space-tether is the most viable method to construct a space debris capture regime with current technology levels. Harpoon heads for the tethers are key design interests as these will penetrate through the satellites and/or debris. The focus of this paper is the analysis of an aluminium 6082, flat and conical head design, used to perforate aluminium 1050A plates using a gas gun laboratory. The aim …

Accuracy Of Commercially-Available Speech Recognition Systems In Identifying Pirep Terminology, Deborah Carstens, Ph.D., Michael S. Harwin, J.D., M.S., Tianhua Li, Ph.D., Michael Splitt, M.S., Ridwan Olabanji, M.S.

International Journal of Aviation, Aeronautics, and Aerospace

Pilot Reports (PIREPs) are an important source of information that aids, other pilots, air traffic control, and operational aviation meteorologists in terms of forecasting and updating weather advisories such as SIGMETs. Pilots rely upon PIREPs so they can avoid hazardous weather and fly their aircraft in the safest manner possible. However, many PIREPs are not successfully submitted or transmitted to the many end users which impedes their ability to be used to keep the NAS safe. The National Transportation Safety Board (NTSB) made several recommendations for increasing the effectiveness and distribution of PIREPs, including receiving PIREPs from pilots directly and …

The Five Hazardous Attitudes, A Subset Of Complacency, Peter S. Neff

International Journal of Aviation, Aeronautics, and Aerospace

Abstract

The article discusses complacency and the five hazardous attitudes in the context that the five hazardous attitudes are a subset of complacency. On the list of 12 most common contributors to aircraft accidents, the FAA lists complacency as the second most often contributor. Complacency implies that there is a level of satisfaction with the present circumstances without any consideration of future unseen potential dangers. Attitude embodies the concept that a person has a predisposed response to certain stimuli. Complacency manifests itself in the form of the five hazardous attitudes: (a) anti-authority, (b) impulsivity, (c) invulnerability, (d) macho, and (e) …

Heat Generation Of Aircraft Tires At Landing, Yu Li, Dr. Weiji Wang

International Journal of Aviation, Aeronautics, and Aerospace

When the aircraft lands on a runway, the great speed difference between tires and runway causes non-negligible friction and speeds up wheels. The generated heat rapidly raises tire temperature and causes material decomposition, which leads to replacement cost and flight safety issues; the chemical substances in the air can also cause emission problems. Many studies on aircraft tire temperature are based on software simulation or experiments. The simulation result may be affected by unnecessary variables due to cumbersome modelling, and the observation result may be inaccurate due to a particularly dynamic friction process. On the other side, there are few …

Classifıcation Of Survivor/Non-Survivor Passengers In Fatal Aviation Accidents: A Machine Learning Approach, Tüzün Tolga İnan Dr.

International Journal of Aviation, Aeronautics, and Aerospace

The safety concept primarily examines the most fatal (resulting in dead passengers) accidents of aviation history in this study. The primary causes of most fatal accidents are; human, technical, and sabotage/terrorism factors. Although the aviation industry started with the first engine flight in 1903, the safety concept has been examined since the 1950s. The safety concept firstly examined the technical factors, and in the late 1970s, human factors started to analyze. Despite these primary causes, there have different factors that affect accidents. So, the study aims to determine the affecting factors of the most fatal accidents to classify the survivor/non-survivor …

Uas For Public Safety: Active Threat Recognition, Joseph Cerreta, Tray Denney, Scott S. Burgess, Anthony Galante, David Thirtyacre, Gloria A. Wilson, Patrick Sherman

International Journal of Aviation, Aeronautics, and Aerospace

The Center for Homeland Defense and Security identified an increase of active threat events, such as mass shootings, annually since 1999. Literature suggests that 90% of shootings were over before law enforcement arrived at the scene and the first responder response was limited to “surround and contain” until Special Weapons and Tactics Teams (SWAT) arrived on the scene. Using Unmanned Aircraft Systems (UAS) to detect which individual was the threat and type of weapon used can provide useful information to increase the speed of the response for first-on-scene rather than waiting for SWAT if the type of weapon was known. …

3d Printing Technology In Aerospace Industry – A Review, Mohammad Suhel Karkun, Sathish Dharmalingam

International Journal of Aviation, Aeronautics, and Aerospace

In the modern era, several new technologies are being developed for the most convenient and easy usage of materials. Due to its effortless and quick usage properties, 3D printing technology has a vast application range nowadays in different fields. The application of 3D printing technology in the aerospace industry has been developed in the past few decades, but now it has been enhanced to a new level. 3D printing technology now has several applications in the aeronautical and space sectors. Soon, 3D printing technology will be used for building habitations on other planets and for the printing of spacecraft and …

Aviation Organization Strategy Development In National Airspace Modernization, Allan Will, Samuel M. Vance

International Journal of Aviation, Aeronautics, and Aerospace

The purpose of this qualitative study was to determine how small sub-directorates within larger organizations develop strategy to accomplish expansive legacy infrastructure re-engineering. There is significant, historical academic inquiry on Technological Transitions (TT)s with respect to infrastructure modernization; the conversion of the National Airspace System from ground-based to space-based navigation is an example of a TT. There are also studies on how to re-engineer legacy software systems to continue supporting organizational needs. This study is intended to explore a case of re-engineering the expansive legacy ground-based navigation system in the United States by efficiently reducing the size of the network …

The Persistence Of Safety Silence: How Flight Deck Microcultures Influence The Efficacy Of Crew Resource Management, Kimberly Perkins, Sourojit Ghosh, Julie Vera, Cecilia Aragon, Adam Hyland

International Journal of Aviation, Aeronautics, and Aerospace

The majority of First Officers and Captains feel that Captains establish the tone of the flight deck microculture. However, the majority of these pilots also report that as First Officers, they have hesitated to share safety-pertinent data and/or experience being silenced after sharing safety data due to a psychologically unsafe flight deck. Utilizing direct feedback from industry pilots, we explore ways that Captains can create a more inclusive microculture that elicits safety voice. The safety system designed to enhance crew collaboration, Crew Resource Management, fails to adequately establish tools for designing a psychologically safe flight deck. We conclude that Crew …

Air Passenger Demand Forecast Through The Use Of Artificial Neural Network Algorithms, Juan Gerardo Muros Anguita, Oscar Díaz Olariaga

International Journal of Aviation, Aeronautics, and Aerospace

Airport planning depends to a large extent on the levels of activity that are anticipated. To plan the facilities and infrastructures of an airport system and to be able to satisfy future needs, it is essential to predict the level and distribution of demand. This document presents a short- and medium-term forecast of the demand for air passengers carried out through a specific case study (Colombia), in which the impact of the pandemic period due to COVID-19 on air traffic was taken into account. To make the forecast, an algorithm that implements techniques based on Artificial Neural Networks (ANN) (Machine …

Integrated Risk Assessment In Ramp Handling Operations: Risk Mapping For Turkish Airports, Ebru Yazgan, Vildan Durmaz, Ayşe Küçük Yılmaz, Konstantinos N. Malagas

International Journal of Aviation, Aeronautics, and Aerospace

Ramp handling acts a vital role in sustainable airport operations. The ramp related services provided to aircraft and their passengers at the airports are related to the landing, take-off, unloading and loading of the aircraft. Human resource is a key component in ramp handling operation and errors by employees cause significant accidents or incidents. The main purpose of the current study is to prioritize critical risk factors in ramp handling operations by using an integrated risk management approach and optimizing human performance while minimizing both failures and errors by employees. In this study, an integrated qualitative and quantitative risk assessment …

Remote Pilot Situational Awareness With Augmented Reality Glasses: An Observational Field Study, Jeffery Coleman, David Thirtyacre

International Journal of Aviation, Aeronautics, and Aerospace

With the use of small unmanned aerial systems (sUAS) proliferating throughout industry and public safety, it is imperative to ensure safety of flight. The Federal Aviation Administration (FAA) published regulations for commercial use of sUAS in 2016 and included the requirement to maintain visual line-of-sight with the aircraft at all times. However, due to the nature of the sUAS ground control stations (GCS), remote pilots time-share between observing the aircraft and interacting with the display on the GCS. Time-sharing between the aircraft and GCS can be seen as similar to the cross-check a pilot uses when flying a manned aircraft. …

Emotional Intelligence And Safety Citizenship Among Army Aviators, Zachary T. Dugger, Bernadette Mccrory

International Journal of Aviation, Aeronautics, and Aerospace

The purpose of this study was to develop an understanding of the relationship between trait emotional intelligence and safety citizenship among United States Army aviators. The study includes analysis of survey responses from 29 individual aviators. Regression analysis was performed to evaluate the relationship between safety citizenship, emotional intelligence, and 15 emotional intelligence facets. Results indicate a significant association (F(1,28) = 15.45; p = 0.001) between safety citizenship and emotional intelligence, and between safety citizenship and 3 emotional intelligence facets: Adaptability (F(1,25) = 23.91; p < 0.001), Self Esteem (F(1,25) = 10.75; p = 0.003), and Optimism (F(1,25) = 8.71; p = …

Comparative Study On The Prediction Of Aerodynamic Characteristics Of Mini - Unmanned Aerial Vehicle With Turbulence Models, Somashekar V, Immanuel Selwyn Raj A

International Journal of Aviation, Aeronautics, and Aerospace

When dealing with CFD simulations the turbulent nature is seen on most of the engineering flows and these flows need to be solved. Reliable and applicable CFD outputs can be obtained from the accurate modelling of the turbulence as it is one of the most vital elements of CFD modelling. The RANS equations are extensively employed to analyse the complex flows over aircraft and for this purpose, a turbulence model is needed for turbulent flow analyses. Compatible turbulence must be chosen for the exact predictions of aircraft aerodynamic characteristics. In this report, numerical analyses of Mini-UAV are done to compare …

Pilot Visual Detection Of Small Unmanned Aircraft On Final Approach During Nighttime Conditions, Jon M. Loffi, Ryan J. Wallace, Samuel M. Vance, Jamey Jacob, Jared C. Dunlap, Taylor A. Mitchell, Dane C. Johnson

International Journal of Aviation, Aeronautics, and Aerospace

In December 2020, the Federal Aviation Administration (FAA) announced the release of a new final rule, permitting operators of small unmanned aircraft systems (sUAS) to perform routine night operations. Public comments to the Notice of Proposed Rulemaking indicated potential safety concerns regarding a pilot’s ability to spot a low-altitude sUAS during nighttime conditions. Leveraging data from the FAA’s UAS Sighting Report Database, the research team evaluated the significance of aircraft encounters with UAS at night. Researchers conducted an inflight experiment in which 10 pilots performed an instrument approach to airport during nighttime conditions in which a multi-rotor sUAS presented a …

Identification Of Wind-Induced Hazard Zones Impacting Uas Bridge Inspection, Jack J. Green, John Mott

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned Aerial Systems (UAS) continue to grow in both popularity and utility within the national airspace system. The use of commercial UAS for civil inspection, specifically that of bridge structures, is becoming commonplace among practitioners and academics alike. The development of an integrated bridge-inspection hazard model provides a way for UAS operators to prepare for and respond to changing environmental conditions that could otherwise prevent a successful UAS flight. The interaction of wind-induced airflow with bridge surfaces creates an aerodynamic wake that can result in hazardous conditions for a UAS platform operating in close proximity. An analysis of this airflow …

Aviation Culture: A ‘Glass Sky’ For Women Pilots - Literature Review, Ivana Gorlin, Donna Bridges

International Journal of Aviation, Aeronautics, and Aerospace

This paper reports on a review of literature covering gender issues in aviation. It considers the impacts of aviation culture on women pilots. The focus of the review was on empirical studies over a 25-year period (1996-2020). Two research questions underpin the review; firstly, we investigated how aviation culture impacts women pilots’ experiences, secondly, we considered its effect on women as pilots. Using a hermeneutic methodological framework, we found that cultural attitudes towards women pilots in the aviation industry are biased and discriminatory. The studies in the review overwhelming concur that the hegemonic masculine culture that dominates aviation significantly diminishes …

A Mathematical Analysis Of The Wind Triangle Problem And An Inquiry Of True Airspeed Calculations In Supersonic Flight, Leonard T. Huang, Lisa I. Cummings

International Journal of Aviation, Aeronautics, and Aerospace

In the first half of this paper, we present a fresh perspective toward the Wind Triangle Problem in aerial navigation by deriving necessary and sufficient conditions, which we call "go/no-go conditions", for the existence/non-existence of a solution of the problem. Although our derivation is based on simple trigonometry and basic properties of quadratic functions, it is mathematically rigorous. We also offer examples to demonstrate how easy it is to check these conditions graphically. In the second half of this paper, we use function theory to re-examine another problem in aerial navigation, namely, that of computing true airspeed — even in …

Folding Methodology For Flexible Aircraft Interiors, Aditya Venkatesh, Fengfeng (Jeff) Xi, Joon Chung

International Journal of Aviation, Aeronautics, and Aerospace

This paper establishes a general furniture folding methodology that is aimed at flexible aircraft cabin interiors. This methodology will allow users to modify existing furniture pieces to their liking and thereby customizing their overall travel experience. The folding methodology also includes a process to quantify the transformation of the furniture pieces. This paper also introduces two design concepts called Open-on-Demand and Reconfiguration to allow passengers to modify an otherwise rigid cabin. The advantages of the multi-functional space saving furniture pieces are also illustrated in this paper. While the general folding methodology was developed for aircraft interiors, it can be adapted …

Quantum Safety Metrics Framework For Commercial Unmanned Aircraft Operators, Tracy L. Lamb, Nathan A. Phillips, Trong Van Nguyen

International Journal of Aviation, Aeronautics, and Aerospace

Commercial unmanned aircraft systems continue to increase in applications and diversity; however, mishaps and accidents erode safety, investment return, and efficiency. Most unmanned aircraft accidents are preceded by leading indicators; the ability to forecast and quantify these may provide increased safety and profitability. This mixed-method research study used a non-experimental parallel convergence approach with multiple instruments, multiple-case study n = 22, and one exemplar case design to develop a quantum safety metric program. This study used a combination of previously validated methods as development instruments, including; the HFACS, STAMP, 'Sierra Scale,' and Accident Prevention Effort equations. The study extended the …

Support To Design For Air Traffic Management: An Approach With Agent-Based Modelling And Evolutionary Search, Gabriella Gigante, Roberto Palumbo, Domenico Pascarella, Alessandro Pellegrini, Gabriella Duca, Miquel Angel Piera, Juan José Ramos

International Journal of Aviation, Aeronautics, and Aerospace

This paper presents a methodology to manage the support to design in ATM operations. We propose a workflow for the design of ATM solutions in a performance-based setting. The methodology includes the evaluation of the impact on human behaviour and exploits a combination of different paradigms, such as Agent-Based Modelling and Simulation, and Agent-Based Evolutionary Search. We prove the soundness of the methodology by carrying out a real case study, which is the transition from Direct Routing to Free Routing in the Italian airspace. The validation results exhibit limited errors for the assessment of the performance metrics under evaluation. Furthermore, …

Predictability Improvement Of Scheduled Flights Departure Time Variation Using Supervised Machine Learning, Deepudev Sahadevan, Palanisamy Ponnusamy Dr, Manjunath K. Nelli Mr, Varun P. Gopi Dr

International Journal of Aviation, Aeronautics, and Aerospace

The departure time uncertainty exacerbates the inaccuracy of arrival time estimation and demand for arrival slots, particularly for movements to capacity constrained airports. The Estimated Take-Off Time (ETOT) or Estimated Departure Time(ETD) for each individual flight is currently derived from Air Traffic Flow Management System (ATFMS), which are solely determined based on individual flight plan Estimated Off Block Time(EOBT) or subsequent delays updated by Airline. Even if normal weather conditions prevail, aircraft departure times will differ from ETOTs determined by the ATFMS due to a number of factors such as congestion, early/delayed inbound flight (linked flights), reactionary delays and air …

Numerical Analysis Of Aerospike Engine Nozzle Performance At Various Truncation Lengths, Sam Dakka Dr, Oliver Dennison

International Journal of Aviation, Aeronautics, and Aerospace

The aerospike engine was first devised in the early 1960s where it provided new means of reaching orbit in a single stage. The paper aimes to demonstrate the viability of the technology by showcasing the increased nozzle thrust efficiency over the conventional bell nozzle. Various truncations were applied to the nozzle and each was subjected to two conditions, an over-expansion and near optimum condition. The nozzle contour was developed using the simple approximation method and was chosen to replicate that of the XRS-2200. This anchored the data, thereby validating the computational fluid dynamics (CFD) simulation. Simulations were completed for at …

Performance Of The Egnos System In Algeria For Single And Dual Frequency, Lahouaria Tabti, Salem Kahlouche, Belkacem Benadda

International Journal of Aviation, Aeronautics, and Aerospace

EGNOS (European Geostationary Navigation Overlay Service) transmits data for more accurate real time positioning with an integrity message for GNSS navigation satellites, which are in view by RIMS station (Ranging and Integrity Monitoring Stations) extended over a continent.

The purpose of this paper is to analyses the performances of EGNOS V2 single frequency L1 and EGNOS V3 dual frequency L1/L5 without RIMS station in Algeria. During this work, four procedures of flight (APV I, LPV 200, APV II and CAT I) were analyses to determine the optimal performances of the EGNOS system in terms of availability and continuity.

We have …

Measuring Safety Culture: Qualitative And Quantitative Means Of Measuring Safety Culture For Safety Management System Optimization, David R. Zubowski

International Journal of Aviation, Aeronautics, and Aerospace

The Department of Transportation Office of the Inspector General (2020) investigated the Federal Aviation Administration oversight of Southwest Airlines Safety Management System and noted concerns and gaps in the oversight, specifically with the lack of guidance provided to inspectors in evaluating organizational safety culture. Using the published report as a case study, this work researched different peer-reviewed articles using qualitative and quantitative means to investigate the benefits, limitations, and assumptions of measuring an organizational safety culture. While different methods were used, academia seems to have settled on definitions for safety culture and safety climate with the majority of researchers using …

Aircraft Exhaust Gas Temperature Value Mining With Rough Set Method, Mustagime Tülin Yıldırım Asst. Prof., Mehtap Taşcı

International Journal of Aviation, Aeronautics, and Aerospace

Aircrafts are one of the most important means of transportation today. For aircrafts to be able to serve safely, their maintenance must be done in a timely and complete manner. In addition to regular maintenance, it may appear suddenly; there is also irregular maintenance performed in cases such as lightning strikes, bird strikes, and hard landings. Engine failures and maintenance has great importance in aircraft maintenance. Using the data recorded during the flight by flight data recorder, the engine health condition is monitored and the necessary maintenance procedures are carried out. In this study, the exhaust gas temperature was estimated …

Notes On Rules Of Thumb For Pilots, Yuzo Inokuchi

International Journal of Aviation, Aeronautics, and Aerospace

The rules of thumb can be found in several flight instructions or pilot's handbooks. Thus far, available rules have been presented without proof or a valid range, such as altitude or velocity ranges wherein these rules can be applied. This paper presents the background theory for a few selected rules; then, the rule is compared with a first-order approximation of the background theory. A valid range is presented by analyzing the prediction accuracy of the rule, which is defined as the relative error of the rule to the background theory. These rules of thumb provide a good approximation of the …

Comparative Study On Performance Accuracy Of Three Probe And Five Probe Flow Analysers For Wind Tunnel Testing, Akhila Rupesh Ms, J V Muruga Lal Jeyan Dr

International Journal of Aviation, Aeronautics, and Aerospace

In the field of inviscid fluid flow studies, the theoretical concept has to be developed even more. In order to make it possible, it is very important to supplement the concepts with strong experimental results. While performing experimentation, various accepts of design can be determined with factors influencing the and also required modification can be recommended in a more systematic and economic manner. Also, the aim objective of the experiment is to extend the underlying theory and to produce new designs with improvements that can be great support to the advancement in technology. In experimental analysis, wind tunnels are used …

Methodology For Convergence Of The Training Program With The Professional Activities Of Aviation Specialists, Zair Ziyaevich Shamsiev

International Journal of Aviation, Aeronautics, and Aerospace

The method of developing curricula for training aviation specialists for civil aviation of the Republic of Uzbekistan is analyzed. It is substantiated that it does not sufficiently take into account the labor market requirements for the composition and content of academic disciplines. An overview of foreign experience in bridging the gap between educational programs and the workplace is given. A method based on a statistical analysis of civil aviation regulations is recommended.