Response-Calibration Techniques For Antenna-Coupled Infrared Sensors,
2010
University of Central Florida
Response-Calibration Techniques For Antenna-Coupled Infrared Sensors, Peter Krenz
Electronic Theses and Dissertations
Infrared antennas are employed in sensing applications requiring specific spectral, polarization, and directional properties. Because of their inherently small dimensions, there is significant interaction, both thermal and electromagnetic, between the antenna, the antenna-coupled sensor, and the low-frequency readout structures necessary for signal extraction at the baseband modulation frequency. Validation of design models against measurements requires separation of these effects so that the response of the antenna-coupled sensor alone can be measured in a calibrated manner. Such validations will allow confident extension of design techniques to more complex infrared-antenna configurations. Two general techniques are explored to accomplish this goal. The extraneous …
Fast-Response Liquid Crystal Displays,
2010
University of Central Florida
Fast-Response Liquid Crystal Displays, Meizi Jiao
Electronic Theses and Dissertations
After about five decades of extensive material research and device development, followed by massive investment in manufacturing technology, thin-film-transistor liquid-crystaldisplay (TFT-LCD) has finally become the dominant flat panel display technology. Nowadays, LCD performances, such as viewing angle, contrast ratio, and resolution, have reached acceptable levels. The remaining major technical challenges are response time, light efficiency, and sunlight readability. Fast response time is desired to reduce motion blur and to enable field sequential color displays using red (R), green (G), and blue (B) LEDs (light emitting diodes) without noticeable color breakup. Sequential RGB colors would eliminate the commonly used spatial color …
Demonstration Of A Neutral Atom Controlled-Not Quantum Gate,
2010
College of Saint Benedict/Saint John's University
Demonstration Of A Neutral Atom Controlled-Not Quantum Gate, L. Isenhower, E. Urban, X. L. Zhang, A. T. Gill, T. Henage, Todd A. Johnson, T. G. Walker, M. Saffman
Physics Faculty Publications
We present the first demonstration of a CNOT gate between two individually addressed neutral atoms. Our implementation of the CNOT uses Rydberg blockade interactions between neutral atoms held in optical traps separated by >8 μm. Using two different gate protocols we measure CNOT fidelities of F=0.73 and 0.72 based on truth table probabilities. The gate was used to generate Bell states with fidelity F=0.48±0.06. After correcting for atom loss we obtain an a posteriori entanglement fidelity of F=0.58.
The Development Of Scalable Pump Techniques For Gg Iag Fiber Lasers And Passive Athermalization Techniques For Solid State Laser,
2010
University of Central Florida
The Development Of Scalable Pump Techniques For Gg Iag Fiber Lasers And Passive Athermalization Techniques For Solid State Laser, William Hageman
Electronic Theses and Dissertations
This dissertation consists of two parts: research pertaining to the development of scalable pump techniques for gain guided index-antiguided fiber lasers and research relating to the development of passive athermalization schemes for solid state lasers. The first section primarily details the development of a side pump scheme that allows for power scaling of gain-guided index anti-guided fibers. While these fibers have been demonstrated in past research, none have used a pump technology capable of pumping with the efficiencies, uniformity, and necessary length to allow for scaling of the fiber lasers to high output powers. The side pumped scheme developed in …
Long Cavity Quantum Dot Laser Diode And Monolithic Passively Mode-Locked Operation,
2010
University of Central Florida
Long Cavity Quantum Dot Laser Diode And Monolithic Passively Mode-Locked Operation, K Shavitranuruk
Electronic Theses and Dissertations
Advantage of the single QD active layer is its potential for very low threshold current density, which in turn can produce low internal optical loss. The low threshold current density and low internal loss thus enable a significant increase in laser diode cavity length. Because of the importance of the threshold current density in heatsinking, future technology of broad-area monolithic laser diodes can be implemented. The dissertation describes the development and the unique characteristics of single QD active layer laser with long cavity. The data are presented on single layer QD laser diodes that reach threshold current densities values of …
Nonlinear Fiber Lasers Using Bismuth Based Erbium Doped Fiber Amplifier.,
2010
Universiti Malaya
Nonlinear Fiber Lasers Using Bismuth Based Erbium Doped Fiber Amplifier., Sharifeh Shahi
Student Works (2010-2019)
A thorough study on Bismuth-based Erbium-doped fiber (Bi-EDF) is presented for wide-band amplifiers and multi-wavelength fiber laser applications. This fiber allows high Erbium ions concentration to be doped without a significant concentration quenching effect. The high refractive index characteristic in the Bi-EDF has broadened the emission spectrum of Erbium ions to achieve a broader gain spectrum up to extended L-band region compared to normal silica-based Erbium-doped fiber (EDF). The Bi-EDFA performances have been investigated in terms of power conversion efficiency (PCE), quantum conversion efficiency (QCE), gain and noise figure. The highest QCE and PCE for a 215 cm long of …
Fabrication Of Integrated Optofluidic Circuits In Chalcogenide Glass Using Femtosecond Laser Direct Writing,
2010
University of Central Florida
Fabrication Of Integrated Optofluidic Circuits In Chalcogenide Glass Using Femtosecond Laser Direct Writing, Troy P. Anderson
Electronic Theses and Dissertations
Femtosecond laser direct writing (FLDW) is a versatile process that uses focused femtosecond pulses to modify the physical structure of a material, which can result in a shift of optical properties such as the linear and nonlinear refractive index. If the photon energy of the femtosecond pulses lies below the material bandgap, nonlinear absorption rather than linear absorption becomes the dominant mechanism of energy transfer to the material. In this manner, a focused femtosecond pulse train can be used to fabricate functional features such as optical waveguides, diffractive optical elements, or micro-fluidic elements within the volume of a transparent medium. …
Nonlinear Absorption And Free Carrier Recombination In Direct Gap Semiconductors,
2010
University of Central Florida
Nonlinear Absorption And Free Carrier Recombination In Direct Gap Semiconductors, Peter D. Olszak
Electronic Theses and Dissertations
Nonlinear absorption of Indium Antimonide (InSb) has been studied for many years, yet due to the complexity of absorption mechanisms and experimental difficulties in the infrared, this is still a subject of research. Although measurements have been made in the past, a consistent model that worked for both picosecond and nanosecond pulse widths had not been demonstrated. In this project, temperature dependent two-photon (2PA) and free carrier absorption (FCA) spectra of InSb are measured using femtosecond, picosecond, and nanosecond IR sources. The 2PA spectrum is measured at room temperature with femtosecond pulses, and the temperature dependence of 2PA and FCA …
Super-Resolution Using Adaptive Wiener Filters,
2010
University of Dayton
Super-Resolution Using Adaptive Wiener Filters, Russell C. Hardie
Electrical and Computer Engineering Faculty Publications
The spatial sampling rate of an imaging system is determined by the spacing of the detectors in the focal plane array (FPA). The spatial frequencies present in the image on the focal plane are band-limited by the optics. This is due to diffraction through a finite aperture. To guarantee that there will be no aliasing during image acquisiton, the Nyquist criterion dictates that the sampling rate must be greater than twice the cut-off frequency of the optics. However, optical designs involve a number of trade-offs and typical imaging systems are designed with some level of aliasing. We will refer to …
Electron Beam Lithography Throughput And Resolution Enhancement With Innovative Blanker Design,
2010
University at Albany, State University of New York
Electron Beam Lithography Throughput And Resolution Enhancement With Innovative Blanker Design, Junru Ruan
Legacy Theses & Dissertations (2009 - 2024)
Electron Beam Lithography (EBL) is one of the most important and most widely used methods for nano-fabrication. The primary advantage of electron beam lithography is its high resolution, and its ability to expose nanometer features without a mask. On the other hand, one of the key limitations of electron beam lithography is throughput. Slow blanking speed is one of the major bottlenecks for the system speed. In this dissertation, I will first review the prior literature of high speed blanking. Thorough theoretical and experimental studies are done on the existing designs. Physical models are built and analytical ray tracing is …
Application Of X-Ray Diffraction To Material Analysis And Medical Imaging,
2010
University at Albany, State University of New York
Application Of X-Ray Diffraction To Material Analysis And Medical Imaging, Wei Zhou
Legacy Theses & Dissertations (2009 - 2024)
Powder diffraction is commonly used to determine the structures of both inorganic and organic materials. The angle and intensity of the diffraction (also called coherent scatter) peak depends on the nanostructure of the material. When no x-ray optic is used, the peak width broadens, and hence the resolution worsens, as the sample area is increased. However, a small sample area gives low diffracted signal intensity, particularly for thin films and for organic materials, which have low diffraction cross sections. X-ray optics can be used in x-ray powder diffraction to increase the diffraction intensity, thus decreasing exposure times. For a small …
Reflectivity Of A Cholesteric Liquid Crystal,
2010
California Polytechnic State University - San Luis Obispo
Reflectivity Of A Cholesteric Liquid Crystal, Justin Lawson
Physics
In this paper we investigate the light properties of a chiral liquid crystal or a crystal for which the director angle relative to some fixed axis changes as a function of the crystal depth. Sometimes a dopant can introduce a chirality or "twist" in a nematic liquid crystal. For such cases of non-linear depth dependence (where chirality is determined by a diffusion equation) we may use this research to work backwards from a crystal's light properties to intensity and duration of dopant exposure.
Development Of Optical Coherence Tomography For Tissue Diagnostics,
2010
University of Central Florida
Development Of Optical Coherence Tomography For Tissue Diagnostics, Panomsak Meemon
Electronic Theses and Dissertations
Microvasculature can be found in almost every part of the human body, including the internal organs. Importantly, abnormal changes in microvasculature are usually related to pathological development of the tissue cells. Monitoring of changes in blood flow properties in microvasculature, therefore, provides useful diagnostic information about pathological conditions in biological tissues as exemplified in glaucoma, diabetes, age related macular degeneration, port wine stains, burn-depth, and potentially skin cancer. However, the capillary network is typically only one cell in wall thickness with 5 to 10 microns in diameter and located in the dermis region of skin. Therefore, a non-invasive flow imaging …
Plasmon Enhanced Near-Field Interactions In Surface Coupled Nanoparticle Arrays For Integrated Nanophotonic Devices,
2010
University of Central Florida
Plasmon Enhanced Near-Field Interactions In Surface Coupled Nanoparticle Arrays For Integrated Nanophotonic Devices, Amitabh Ghoshal
Electronic Theses and Dissertations
The current thrust towards developing silicon compatible integrated nanophotonic devices is driven by need to overcome critical challenges in electronic circuit technology related to information bandwidth and thermal management. Surface plasmon nanophotonics represents a hybrid technology at the interface of optics and electronics that could address several of the existing challenges. Surface plasmons are electronic charge density waves that can occur at a metal-dielectric interface at optical and infrared frequencies. Numerous plasmon based integrated optical devices such as waveguides, splitters, resonators and multimode interference devices have been developed, however no standard integrated device for coupling light into nanoscale optical circuits …
New Laser Technologies Analysis Of Quantum Dot And Lithographic Laser Diodes,
2010
University of Central Florida
New Laser Technologies Analysis Of Quantum Dot And Lithographic Laser Diodes, Abdullah Demir
Electronic Theses and Dissertations
The first part of this dissertation presents a comprehensive study of quantum dot (QD) lasers threshold characteristics. The threshold temperature dependence of a QD laser diode is studied in different limits of p-doping, hole level spacing and inhomogeneous broadening. Theoretical analysis shows that the threshold current of a QD laser in the limit of uniform QDs is not temperature independent and actually more temperature sensitive than the quantum well laser. The results also explain the experimental trends of negative characteristic temperature observed in QD lasers and clarify how the carrier distribution mechanisms inside and among the QDs affect the threshold …
Application Of Antenna Synthesis And Digital Signal Processing Techniques For Active Millimeter-Wave Imaging Systems,
2010
University of Central Florida
Application Of Antenna Synthesis And Digital Signal Processing Techniques For Active Millimeter-Wave Imaging Systems, Wilson Ariel Caba
Electronic Theses and Dissertations
Millimeter-wave imaging has gathered attention in recent years for its ability to penetrate clothing, thin layers of soils, and certain construction materials. However, image quality remains a challenge that needs to be addressed. One way of improving image quality is by increasing the dimensions of the collecting aperture. A sparse array can be used to synthesize a larger aperture with a limited set of relatively small detectors. In this research we design, build, and test a test-bed having an active source at 94 GHz and an array of coherent detectors, mounted on arms that extend radially on a rotary table. …
Modeling And Design Of A Photonic Crystal Chip Hosting A Quantum Network Made Of Single Spins In Quantum Dots That Interact Via Single Photons,
2010
University of Central Florida
Modeling And Design Of A Photonic Crystal Chip Hosting A Quantum Network Made Of Single Spins In Quantum Dots That Interact Via Single Photons, Hubert P. Seigneur
Electronic Theses and Dissertations
In this dissertation, the prospect of a quantum technology based on a photonic crystal chip hosting a quantum network made of quantum dot spins interacting via single photons is investigated. The mathematical procedure to deal with the Liouville-Von Neumann equation, which describes the time-evolution of the density matrix, was derived for an arbitrary system, giving general equations. Using this theoretical groundwork, a numerical model was then developed to study the spatiotemporal dynamics of entanglement between various qubits produced in a controlled way over the entire quantum network. As a result, an efficient quantum interface was engineered allowing for storage qubits …
Morphological, Structural, And Optical Studies Of Undoped And Doped-Zno Nanostructure.,
2010
Universiti Malaya
Morphological, Structural, And Optical Studies Of Undoped And Doped-Zno Nanostructure., Ramin Yousefi
Student Works (2010-2019)
Research concerning one-dimensional nanomaterials has grown tremendously ever since carbon nanotubes were discovered by Iijima (1991), silicon nanowires were grown by Lieber's group (1998), and ZnO nanowires and nanobelts were found by Wang's group from Georgia Tech (Pan et al., 2001). Such researches on one-dimensional structures have been one of the most important branches of science during recent decades. We can now observe the impact of these studies on the technology of one-dimensional materials and also the advanced prospect of developing new technologies. Based on this motivation, this thesis attempts to investigate some unknown properties of ZnO nanostructures as …
Automated Waveguide Alignment And Direct Uv Writing Systems For Integrated Optical Devices Fabrication And Characterization.,
2010
Universiti Malaya
Automated Waveguide Alignment And Direct Uv Writing Systems For Integrated Optical Devices Fabrication And Characterization., Tan Chin Chong
Student Works (2010-2019)
This dissertation reports the studies on the development of waveguide alignment techniques as well as the UV writing coding structures for optical circuitries through a programming platform, LabVIEW. In the first part of the work, 1-by-4 silica splitter was pigtailed with a single mode fiber which placed on a stepper motorized stage. The developed alignment techniques are image analysis for waveguide alignment, initial light seeking from interference fringes, manual alignment of launch fiber for waveguide’s input, and peak power detection. These waveguide alignment techniques covered from the search of input channel within waveguide to the performance test. While, in the …
Design And Simulation Of Silica-On-Silicon Pump/Signal Multiplexer For Hybrid Passive-Active Optical Devices.,
2010
Universiti Malaya
Design And Simulation Of Silica-On-Silicon Pump/Signal Multiplexer For Hybrid Passive-Active Optical Devices., Alvin Law Wen Pin
Student Works (2010-2019)
This dissertation describes the design and simulation of silica-on-silicon pump/signal multiplexer for hybrid passive-active optical devices. Uniform symmetric directional couplers and planar Bragg gratings were utilized in this work, forming the essential building blocks in a waveguide amplifier. Several designs in relation to the multiplexers are presented in this work, with the simplest application for the directional coupler as a pump/signal multiplexer. A 980/1550 nm and an 800/1310 nm pump/signal multiplexers for erbium doped and bismuth doped waveguide amplifier, respectively were modeled. These couplers were designed and simulated in Rsoft BeamPROP environment, utilizing 3D Finite Difference Beam Propagation Method (FD-BPM) …
