Engineering Commons^™

Oxygen Diffusion Characterization Of Frp Composites Used In Concrete Repair And Rehabilitation, Chandra K. Khoe

USF Tampa Graduate Theses and Dissertations

Many independent studies have conclusively demonstrated that fiber reinforced polymers (FRP) slow down chloride-induced corrosion of steel in concrete. The mechanism for this slow down is not well understood but it has been hypothesized that FRP serves as a barrier to the ingress of chloride, moisture, and oxygen that sustain electrochemical corrosion of steel.

This dissertation presents results from an experimental study that determined the oxygen permeation rates of materials used in infrastructure repair. In the study, the oxygen permeation constants for epoxy, carbon and glass fiber laminates, concrete, epoxy-concrete and FRP-concrete systems were determined and a method developed to …

Structure-Property-Performance Ofnnanocomposite Cr-Si-N Films Synthesized By A Duplex Surface Treatment Technique, Daohui Lai, Jiang Xu, Zong-Han Xie, Paul R. Munroe

Research outputs 2011

Nanocomposite Cr–Si–N films were prepared on to Ti–6Al–4V substrates by a novel duplex surface treatment technique. Coatings consisting of a Cr3Si surface layer were deposited using a double cathode glow plasma and subsequent surface plasma nitriding. The surface topography, chemical composition, and microstructure of these treated alloys were analyzed by a variety of surface characterization techniques. The resulting Cr–Si–N films consisted of nanocrystallite CrN grains embedded in amorphous SiNx phase. Nanoindentation tests showed that with increasing nitrogen partial pressure the hardness of the Cr–Si–N films increased and the elastic modulus decreased. Wear experiments showed that the Cr–Si–N films produced at …

Corrosion Electrochemical Behavior Of Am60 Magnesium Alloys In Automobile Engine Coolants, Ling-Jie Li, Sha Wang, Yin Xiao, Jun Lan, Jing-Lei Lei, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

The polarization measurements and electrochemical impedance spectroscopy(EIS) were used to study the corrosion electrochemical behavior of AM60 magnesium alloys in three kinds of commercial coolants for automobile engine.Results show that the tested commercial coolants are slightly corrosive to AM60 magnesium alloys and their corrosivity varies from coolant to coolant.The coolant C is the least corrosive among the studied commercial coolants and the coolant A is more corrosive than the coolant B and C.The coolant C appears to be the most promising coolant for automobile engine made by magnesium alloys.The coolant resistivity plays an important role in the corrosion of AM60 …

Effect Of Cldh On Rebar Corrosion Behavior In Chloride Contaminated Neutral Pore Solutions, Yu-Ming Tang, Le Niu, Yu Zuo

Journal of Electrochemistry

he effect of calcined LDH-MgAl-CO₃ on rebar corrosion behavior in chloride ion contaminated neutral concrete pore solutions was investigated in this paper.Corrosion potentials of rebars in pore solutions after treatment with CLDH were higher than before treatment.According to polarization tests,passivated region of rebars in pore solutions after treatment with CLDH was found apparently instead of activation.EIS tests showed that CLDH made the impedance of specimens increase.The measurements of pH and chloride ion concentration after treatment indicated that / of pore solutions decreased by 4～5 magnitude orders.

Tribological Comparison Of Traditional And Advanced Firearm Coatings, Greg Boban

Master's Theses

The objective of this project is to find which type of coating has the best performance characteristics for finishing firearms. This is accomplished by measuring and comparing several performance characteristics, such as: adhesion, hardness, wear resistance, friction control, and corrosion resistance. Appearance is not a factor since any exterior coating that is flashy can be subdued or camouflaged with special purpose paints, which have proven durable enough for such purposes. Cost will not be a limiting factor for this experiment, but will be discussed in the conclusion as a secondary concern. This data will be used to identify the best …

Elimination Of Deck Joints Using A Corrosion Resistant Frp Approach, Ashok Reddy Aleti

Doctoral Dissertations

The research presented herein describes the development of durable link slabs for jointless bridge decks based on using FRP grid for reinforcement. Specifically, the ductility of the FRP material was utilized to accommodate bridge deck deformations imposed by girder deflection, temperature variations, and concrete shrinkage. It would also provide a solution to a number of deterioration problems associated with bridge deck joints.

The design concept of the link slabs was then examined to form the basis of design for FRP grid link slabs. Improved design of FRP grid link slab/concrete deck slab interface was confirmed in the numerical analysis. The …

Mitigation Of Chloride And Sulfate Based Corrosion In Reinforced Concrete Via Electrokinetic Nanoparticle Treatment, Kunal Kupwade-Patil

Doctoral Dissertations

Concrete is a porous material which is susceptible to the migration of highly deleterious species such as chlorides and sulfates. Various external sources, including sea salt spray, direct seawater wetting, deicing salts and chlorides can contaminate reinforced concrete. Chlorides diffuse into the capillary pores of concrete and come into contact with the reinforcement. When chloride concentration at the reinforcement exceeds a threshold level it breaks down the passive oxide layer, leading to chloride induced corrosion. The application of electrokinetics using positively charged nanoparticles for corrosion protection in reinforced concrete structures is an emerging technology. This technique involves the principle of …

Corrosion-Related Gas Measurements And Analysis For A Suite Of Coals In Staged Pulverized Coal Combustion, Todd A. Reeder

Theses and Dissertations

Eleven gas species, including CO, CO2, H2, H2O, H2S, HCl, NOX, O2, SO2, COS and SO3, were measured in a 150 kWth, staged, pulverized coal, down-fired combustor using a Fourier transform infrared (FTIR) spectrometer, gas chromatograph (GC), and a Horiba PG-250 5-gas analyzer. Additional gases such as HCN, NH3, CH4, and other hydrocarbons were also measured. Seven coals of varying rank and composition were investigated. Measurements were obtained in reducing (S.R. = 0.85) and oxidizing (S.R. = 1.15) conditions. In particular, sulfur- and chlorine-containing species including H2S, SO2, COS, SO3, and HCl are discussed. In the reducing zone, all four …

Studied Corrosion Behaviors Of Reinforcing Steel In Concrete By A Single-Dimensional Array Electrode, Lan-Qiang Li, Shi-Gang Dong, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

A single-dimensional array electrode was developed as a new electrochemical technique to image corrosion potential,galvanic current and polarization curves of reinforcing steel in concrete during corrosion process.Combining with the polarization behavior for each micro-electrode,the interactions between corrosion macrocell and corrosion microcell of the steel in concrete were evaluated.It was noticed that the corrosion macrocell and microcell occurred independently in difference regions at the initial stage of corrosion.The corrosion macrocell current can be in situ followed by corrosion potential imaging.The corrosion propagation of steel in concrete is closely related to the interactions between corrosion macrocell and corrosion microcell.

Characterization Of Explanted Endovascular Stents: A Study Of In-Vivo Corrosion And The Role Of Vascular Calcification In Stent Fracture, Dina Halwani

All ETDs from UAB

The electrochemical and mechanical stability of endovascular stents in-vivo is essential for their biocompatibility. Limited information is available regarding the condition of stents following interaction with vascular tissue, as a result, twenty seven stented vessels containing 45 stents (33 bare metal and 12 drug eluting) were retrieved during autopsy and vascular surgery. The stent/tissue components were carefully separated using a rigorous tissue dissolution protocol. Stent surfaces were characterized using 3D digital optical and scanning electron microscopy. Transferred metallic elements in dissolved tissue were measured using mass spectroscopy. Histopathologic assessment of stented tissue, when available, was also performed. Fifteen out of …

Electrical Impedance Imaging Of Corrosion On A Partially Accessible 2-Dimensional Region, Court Hoang, Katherine Osenbach

Mathematical Sciences Technical Reports (MSTR)

In this paper we examine the inverse problem of determining the amount of corrosion on an inaccessible surface of a two-dimensional region. Using numerical methods, we develop an algorithm for approximating corrosion profile using measurements of electrical potential along the accessible portion of the region. We also evaluate the effect of error on the problem, address the issue of ill-posedness, and develop a method of regularization to correct for this error. An examination of solution uniqueness is also presented.

Service Life Prediction Of Pier For The Existing Reinforced Concete Bridges In Chloride-Laden Environment, Ming-Te Liang, Ran Huang, Shen-An Feng, Chi-Jang Yeh

Journal of Marine Science and Technology–Taiwan

The prediction method of service life for bridge structures is played an important role of bridge management system. In this paper, the mathematical modeling was to study the servise life prediction of pier for existing reinforced concrete (RC) bridge exposed to chloride environment. The corrosion process has three stages, the initiation time (tc), the depassivation time (tp), and the corrosion (propagation) time (tcorr). The total service life of pier for the existing RC bridge can be expressed as t = tc + tp + tcorr. Many mathematical models were applied to predicting each value of the tc, tp, and tcorr. …

Synergism Of Complex Additives Of Dtab+Ktl For Zinc Corrosion Inhibition In Koh Solutions, Sheng-Zhou Lin, Zeng-Xin Cai, Gui-Sheng Wang, He-Bing Zhou, Wei-Shan Li

Journal of Electrochemistry

The electrochemical behaviors of Zn in 3mol/L KOH solution containing several kinds of inhibitors were investigated by weight-loss,electrochemical methods and SEM. The results showed that both the single ad-ditive and the mixed additives can suppress the corrosion of zinc in 3 mol/LKOH solution. And the inhibition ef-feciency of the mixed additives is higher than that of any single additive because of the synergistic effect between KTL and DTAB. The adsorption of DTAB on the surface of zinc has been enhanced in the presence of KTL.

Applications Of Electricity In The Rehabilitation And Health Monitoring Of Concrete Structures, Saiprasad Vaidya

Doctoral Dissertations

The dissertation research work presented herein consists of two separate findings: one investigates a potential new coating technique that could be used to rehabilitate deteriorated concrete sewer pipes, and the other researches inducing electrical conductivity into geopolymer concrete to serve as smart material by being able to sense stress changes. Both applications utilize electricity to enhance the performance and/or functionality of hardened cementitious materials.

Microbiologically induced corrosion (MIC) in concrete wastewater conveyance systems is a leading deterioration mechanism in such structures. This work focuses on breaking the MIC cycle by preventing colonization of the bacteria responsible for converting hydrogen sulfide …

The Effect Of Particle Surface Area To Volume Ratio On Ion Release From Cocr Spheres, Darin J. Grandfield

Master's Theses

In 2005, over 200,000 Americans underwent a hip arthroplasty, the replacement of a hip joint with an artificial prosthesis. Of these arthroplasties, metal-on-metal type implants represent an increasing usage percentage. Metal-on-metal implants are selected largely for their low volumetric wear rate, durability, and resistance to corrosion. In spite of these advantages, little is known concerning the long-term consequences of heavy metal alloy use in the body, although early research indicates potentially carcinogenic results. This thesis is a preliminary investigation into these long term effects and their root causes.

An improved comprehension of the corrosion kinetics and the rate of ion …

Electrodeposition Of Al On Magnesium Alloy In Ionic Liquid, Wen-Ta Tsai, Shu-You Chen, Mu-Huan Zhuang, Jeng-Kuei Chang, Yi-Wen Sun

Journal of Electrochemistry

Electrodeposition of a metallic aluminum on a magnesium alloy in acidic aluminum chloride-1-ethyl-3-methylimidazolium chloride ionic liquids(AlCl₃-EMIC) was investigated.The effects of current density and AlCl₃ content in the ionic liquid on the electrodeposition behavior were studied.The results showed that aluminum could be successfully electrodeposited on the AZ91D substrate.At-0.2 V,the ionic liquid containing 60 m/o AlCl₃ was optimum for Al electrodeposition.The current efficiency was higher if electrodeposition was performed at a lower applied current density.The existence of Al coating could caused a substantial increase in open circuit potential,reducing the susceptibility of Mg alloy to corrosion.The results of electrochemical …

Developments Of Scanning Electrochemical Probes And Their Applications In Studying Of Localized Corrosions, Chang-Jian Lin, Yan Li, Bin Lin, Rong-Gang Hu, Min Zhang, Xiang-Dong Zhuo, Rong-Gui Du

Journal of Electrochemistry

The electrochemical inhomogeneities always exist at the interface of metal/solution,and play an important and often controlling role in localized corrosion of metals in a given environment.It is necessary to develop in situ imaging techniques for further studying the electrochemical and environmental inhomogeneities at the interface of metal/solution for the localized corrosion system.In this paper,various techniques with spatial resolution,such as scanning micro reference electrode(SMET),scanning electrochemical microscope(SECM),atomic force microscope(AFM),and scanning Kelvin probe(SKP),and their applications in corrosion studies were briefly reviewed.The chemical probes and array electrode have been developed.It was concentrated to describe our newly developed techniques of the scanning electrochemical probes,including SMET …

Simulation And Behavior Of Corrosion Deteriorated Reinforced Concrete Members, M. A. Shayanfar, Amir Safiey

Publications

Several reinforced concrete (RC) infrastructures are now crumbling from corrosion of steel bars in concrete. The paper presents the recent advancements in analytical simulation of corrosion aftereffects on behavior of RC members. The model juxtaposes the experimental findings with analytical relationships. The implementation of the model into a nonlinear finite element formulation as well as the experimental and analytical backgrounds are discussed. The abilities of the resulted program have been studied by modeling some experimental specimens showing a reasonable agreement between the analytical and experimental findings.

Nondestructive Method To Detect Corrosion Of Steel Elements In Concrete, Saeed Javidi Niroumand, Aaron Jon Yakel, Atorod Azizinamini, Marcelo Dasilva

Nebraska Department of Transportation: Research Reports

No abstract provided.

Effectiveness Of Thermal Oxidation In Relation To Anterior Cervical Plates, Katherine A. Miyashiro

Master's Theses

Ti-6Al-4V anterior cervical plates (ACP) are used in spinal fusion surgeries to fixate cervical vertebrae during graft adhesion. However, documented cases of implant failure and the potential for ACP corrosion raise concerns regarding any degradation of material resulting from extended implantation. In addition, abrasion during implantation may damage a section of the protective oxide layer, potentially exposing surrounding tissues to the harmful effects of bare titanium, aluminum, and vanadium. Thermal oxidation has been shown to improve corrosion-resistance and wear-resistance, depending on temperature and time. To quantify the attributes of the thermally grown oxide layer, Ti-6Al-4V coupons underwent thermal oxidation treatments …

Influence Of Magnesium Nitrate On The Corrosion Performance Of Sol-Gel Coated Aa2024-T3 Aluminium Alloy, Rajath Varma, Brendan Duffy, John Cassidy

Articles

Traditional anti-corrosion technology has relied heavily on using reducible metal species, predominantly hexavalent chromium (Cr(VI)), for protecting reactive metal alloys such as aluminium which is extensively used in the aerospace sector. However, the impending changes in the use of Cr(VI) in Europe and the United States have forced aerospace manufacturers to examine alternative materials for protecting aluminium. One of the most promising alternatives being investigated are organosilane based sol-gels containing anticorrosion additives. In this work the anti-corrosion properties of magnesium (II) nitrate (Mg(NO3)2) as a inhibitor was investigated at different concentrations (0.1% - 1.0 wt %) in a methyltriethoxysilane (MTEOS) …

Thermal Spray Coatings: Effect Of Selected Coating Parameters On Corrosion Resistance, David Culliton, David Kennedy, Tony Betts, P. Concannon

Conference Papers

Thermal Spray coatings have long been adopted as a surface modification technique. Unique in their ability to mechanically bond to the surface of most substrate materials, the Thermal Spray coatings offer a generic solution to improving mechanical, corrosion or tribo-corrosion properties of the affected substrate material. Of the available systems, Flame Spray techniques offer the simplest and most cost-effective method of applying these coatings. In the current study, an investigation was conducted into the comparative performance of a selection of these coating systems – a polymer coating, with various coating thicknesses, and a metallic coating - in a number of …

Fatigue Fracture And Microstructural Analysis Of Friction Stir Welded Butt Joints Of Aerospace Aluminum Alloys, Vinay Raghuram

LSU Master's Theses

Friction-Stir-Welding (FSW) has been adopted as a major process for welding Aluminum aerospace structures. Al-2195, which is one of the new-generation Aluminum alloys that has been used on the external tank of the new super lightweight external tank of the space shuttle. The Lockheed Martin Space Systems (LMSS), Michoud Operations in New Orleans is continuously pursuing Friction-Stir-Welding technologies in its efforts to advance fabrication of the external tanks of the space shuttle. The future launch vehicles which will have to be reusable, m, an dates the structure to have good fatigue properties, which prompts an investigation into the fatigue behavior …

Oxidation Modeling By Means Of Molecular Dynamics, Chaiyod Soontrapa

UNLV Theses, Dissertations, Professional Papers, and Capstones

Oxidation modeling is normally engineered to study systems at macroscopic scales, mostly in analytical forms based on diffusion theories. The associated time scale is usually in months, days, or minutes, and the length scale is in the order of microns. In this dissertation, oxidation modeling is performed at atomistic scale with the time and length scales in picoseconds and angstroms, respectively, using molecular dynamics. Molecular dynamics simulations generate trajectories of each atom or particle in a system according to the laws of physics. Studying oxidations under the atomistic point of view can offer new insights on atomic behaviors and influencing …

Study Of Corrosion Of Materials In The Sulfur-Iodine Hydrogen Production Cycle, Thao Trung Ho

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hydrogen is of great interest since the availability of traditional fossil fuels is in decline. Strictly speaking, hydrogen is not a primary source of energy but is an energy carrier, since energy typically must be used from another source (electricity, natural gas, coal, etc.) to produce it. Of hydrogen production techniques, the Sulfur-Iodine thermochemical water splitting process (S-I cycle), which was proposed by General Atomics (GA), is promising with its simplicity and high efficiency. Most of the chemicals are recycled except water. However, the S-I cycle operates in a harsh, corrosive environment in the presence of a mixture of iodine …

A Novel Capacitance Sensor For Fireside Corrosion Measurement, Heng Ban, Zuoping Li

Mechanical and Aerospace Engineering Faculty Publications

Fireside corrosion in coal-fired power plants is a leading mechanism for boiler tube failures. Online monitoring of fireside corrosion can provide timely data to plant operators for mitigation implementation. This paper presents a novel sensor concept for measuring metal loss based on electrical capacitance. Laboratory-scale experiments demonstrated the feasibility of design, fabrication, and operation of the sensor. The fabrication of the prototype sensor involved sputtering deposition of a thin metal coating with varying thickness on a ceramic substrate. Corrosion metal loss resulted in a proportional decrease in electrical capacitance of the sensor. Laboratory experiments using a muffle furnace with an …

Corrosion Inhibition Of Magnesium Alloy In 3.5% Nacl Medium By Tungstate, Ling-Jie Li, Zhi-Ming Yao, Jing-Lei Lei, Dong-Hai He, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS),Tafel polarization curves and scanning electron microscopy(SEM) were used to study the corrosion inhibition of AZ61 magnesium alloy in 3.5% NaCl medium with tungstate.Results showed that tungstate demonstrates strong inhibition to the corrosion of AZ61 magnesium alloy.At the concentration of 0.01 mol/L,tungstate has a high inhibition efficiency 75.5%.Tungstate is an anodic inhibitor that mainly inhibited the anodic reactions of magnesium alloy through forming a compact protective layer that covered the magnesium alloy surface active sites.

Corrosion Damage Studies Through Microscopy And Stress Analysis, Ronak Patel

Theses and Dissertations

Corrosion is the destructive result of chemical reaction between a metal or metal alloy and its environment. Airplanes, power generating plants, chemical process and manufacturing plants, concrete structure, and many others which widely uses aluminum alloy and stainless steel alloys are subjected to corrosion. The estimated cost of corrosion damage is in order of 3 to 5 percent of gross national product (GNP). Out of all forms of corrosion, pitting corrosion is most commonly observed in aluminum alloy 2024 and stainless steel type 316. There is a need to study the stress environment around the pits in order to predict …

Localised Galvanic Corrosion Processes In Thermal Spray Coated/Cast Aluminium Alloy Systems, David Culliton, Tony Betts, David Kennedy

Conference Papers

Cast Aluminium Alloys, because of the propensity of aluminium to react with impurities and alloying elements, are prone to developing IM impurities during the solidification process. These IM phases can act, in some fluids, as initiation sites for localised corrosion processes, resulting in degradation phenomena, such as pitting. Whilst Thermal Spray coatings can improve the wear resistance of Cast Aluminium Alloys, their corrosion performance may be hampered by the presence of through porosity within the coating.

The present work details some preliminary studies of the localised corrosion processes occurring at the interface area between a Thermal Spray coating and a …

A New Approach For Nonlinear Finite Element Analysis Of Reinforced Concrete Structures With Corroded Reinforcements, Mohsen A. Shayanfar, Amir Safiey

Publications

A new approach for nonlinear finite element analysis of corroded reinforcements in reinforced concrete (RC) structures is elaborated in the article. An algorithmic procedure for producing the tension-stiffening curve of

RC elements taking into consideration most of effective parameters, e.g.: the rate of steel bar corrosion, bond-slip behavior, concrete cover and amount of reinforcement, is illustrated. This has been established on both experimental and analytical bases. This algorithm is implemented into a nonlinear finite element analysis program. The abilities of the resulted program have been studied by modeling some experimental specimens showing a reasonable agreement between the analytical and experimental …