Mechanical Engineering Commons^™

Buckling Failure Boundary For Cylindrical Tubes In Pure Bending, Daniel Peter Miller

Theses and Dissertations

Bending of thin-walled tubing to a prescribed bend radius is typically performed by bending it around a mandrel of the desired bend radius, corrected for spring back. By eliminating the mandrel, costly setup time would be reduced, permitting multiple change of radius during a production run, and even intermixing different products on the same line. The principal challenge is to avoid buckling, as the mandrel and shoe are generally shaped to enclose the tube while bending. Without the shaped mandrel, buckling will likely occur sooner, that is, at larger bend radii. A test apparatus has been built for arborless bending. …

Application Of High Resolution Electron Backscatter Diffraction(Hr-Ebsd) Techniques To Twinning Deformation Mechanism In Az31 Magnesium Alloy, Ali Khosravani

Theses and Dissertations

The application of high resolution electron backscatter diffraction (HR-EBSD) techniques has been used in order to study the evolution of geometrically necessary dislocation (GND). The tested materials were taken from AZ31 magnesium sheet which had strong basal texture. Because of low symmetry of the magnesium crystal lattice, the von Mises criteria cannot be satisfied by the three independent, easily activated, basal slips. The strain along the c-axis of the crystal must be accommodated by either twinning and/or slip systems. HR-EBSD data was taken in order to investigate these phenomena. The HR-EBSD results were post processed in order to resolve total …

A Methodology For Strategically Designing Physical Products That Are Naturally Resistant To Reverse Engineering, Stephen P. Harston

Theses and Dissertations

Reverse engineering - defined as extracting information about a product from the product itself - is a design tactic commonly used in industry from competitive benchmarking to product imitation. While reverse engineering is a legitimate practice - as long as the product was legally obtained - innovative products are often reverse engineered at the expense of the pioneering company. However, by designing products with built-in barriers to reverse engineering, competitors are no longer able to effectively extract critical information from the product of interest. Enabling the quantification of barriers to reverse engineering, this dissertation presents a set of metrics and …

High Speed Friction Stir Spot Welding On Dp 980 Steel:Joint Properties And Tool Wear, Nathan David Saunders

Theses and Dissertations

With the desire to improve passenger safety and fuel efficiency, Ultra High Strength Steels (UHSS) have been developed for use in the automotive industry. UHSS are high strength steels with high ductility and strength. DP 980 is one of these UHSS being applied in automobile manufacturing. DP 980 is difficult to join with Resistance Spot Welding (RSW) because of the high carbon content and alloying in this material. The weld becomes brittle when it solidifies during the welding process. With the desire and motivation of widely using UHSS, new welding processes are needed to be developed in order to effectively …

Partnership For High Performance Housing Final Report, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

This report describes research conducted by the Florida Solar Energy Center (FSEC) under funding from the Pacific Northwest National Laboratory. This work falls under the umbrella of the U.S. Department of Energy's Building America program. High performance goals were set for renovation of existing housing and construction of new affordable housing. Both efforts included monitoring the energy use of several homes.

Mathematical Framework For Early System Design Validation Using Multidisciplinary System Models, Bradley Jared Larson

Theses and Dissertations

A significant challenge in the design of multidisciplinary systems (e.g., airplanes, robots, cell phones) is to predict the effects of design decisions at the time these decisions are being made early in the design process. These predictions are used to choose among design options and to validate design decisions. System behavioral models, which predict a system's response to stimulus, provide an analytical method for evaluating a system's behavior. Because multidisciplinary systems contain many different types of components that have diverse interactions, system behavioral models are difficult to develop early in system design and are challenging to maintain as designs are …

Application Of Subjective Logic To Vortex Core Line Extraction And Tracking From Unsteady Computational Fluid Dynamics Simulations, Ryan Phillip Shaw

Theses and Dissertations

Presented here is a novel tool to extract and track believable vortex core lines from unsteady Computational Fluid Dynamics data sets using multiple feature extraction algorithms. Existing work explored the possibility of extracting features concurrent with a running simulation using intelligent software agents, combining multiple algorithms' capabilities using subjective logic. This work modifies the steady-state approach to work with unsteady fluid dynamics and is designed to work within the Concurrent Agent-enabled Feature Extraction concept. Each agent's belief tuple is quantified using a predefined set of information. The information and functions necessary to set each component in each agent's belief tuple …

Creating Performance Curves For Variable Refrigerant Flow Heat Pumps In Energyplus, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

This document describes methods to generate performance curve coefficients for variable refrigerant flow heat pumps in DOE's EnergyPlus building energy simulation program. Manufactures performance data for capacity and power are used to create full-load and part-load performance curves for cooling and heating operating modes. When performance variations for full-load capacity or power cannot be modeled using a single performance curve, the data set is divided into lower and upper temperature regions and dual performance curves are used. Table objects may also be created to substitute when performance curves do not provide the required accuracy. These performance curves or tables are …

Investigation And Implementation Of A Robust Temperature Control Algorithm For Friction Stir Welding, Kenneth A. Ross

Theses and Dissertations

In friction stir welding, the temperature of the process zone affects the properties of the resulting weld and has a dramatic effect on tool life in PCBN (polycrystalline cubic boron nitride) tools. Therefore an active control system that changes process parameters to control weld temperature is desirable. Mayfield and Sorensen proposed a two-stage control model that contains an inner loop that controls the spindle speed to keep power constant and an outer loop for setting the desired power based on weld temperature. This work contains the analysis and implementation of a temperature control method based on their work. This research …

A Novel Ultrasonic Method To Quantify Bolt Tension, Jairo Andres Martinez Garcia

USF Tampa Graduate Theses and Dissertations

The threaded fasteners are one of the most versatile methods for assembly of structural components. For example, in bridges large bolts are used to fix base columns and small bolts are used to support access ladders. Naturally not all bolts are critical for the operation of the structure. Fasteners loaded with small forces and present in large quantities do not receive the same treatment as the critical bolts. Typical maintenance operations such tension measurements, internal stress checking or monitoring of crack development are not practical due to cost and time constrains. Although failure of a single non-critical fastener is not …

Metal Oxide Graphene Nanocomposites For Organic And Heavy Metal Remediation, Tanvir E. Alam

USF Tampa Graduate Theses and Dissertations

This thesis consists of two research problems in the water decontamination area. In the first work, the main focus is to understand the structure and photocatalytic activity of titanium dioxide with graphene (G-TiO2) which is synthesized by using sol-gel method. The photocatalytic activity of TiO2 is limited by the short electron hole pair recombination time. Graphene, with high specific surface area and unique electronic properties, can be used as a good support for TiO2 to enhance the photocatalytic activity. The obtained G-TiO2 photocatalysts has been characterized by X-Ray Diffraction (XRD), Raman Spectroscopy, Transmission Electron Microscopy (TEM), FTIR Spectroscopy and Ultraviolet …

Acoustic Testing And Modeling: An Advanced Undergraduate Laboratory, Daniel A. Russell, Daniel O. Ludwigsen

Physics Publications

This paper describes an advanced laboratory course in acoustics, specifically targeted for students with an interest in engineering applications at a school with a strongly integrated industrial co-op program. The laboratory course is developed around a three-pronged approach to problem solving that combines and integrates theoretical models, computational models, and experimental data. The course is structured around modules that begin with fundamental concepts and build laboratory skills and expand the knowledge base toward a final project. Students keep a detailed laboratory notebook, write research papers in teams, and must pass laboratory certification exams. This paper describes the course layout and …

Effect Of Gold Content On The Microstructural Evolution Of Sac305 Solder Joints Under Isothermal Aging, Mike Powers, Jianbiao Pan, Julie Silk, Patrick Hyland

Industrial and Manufacturing Engineering

Au over Ni on Cu is a widely used printed circuit board (PCB) surface finish, under bump metallization (UBM), and component lead metallization. It is generally accepted that less than 3 wt.% Au in Sn-Pb solder joints inhibits formation of detrimental intermetallic compounds (IMC). However, the critical limit for Au content in Pb-free solder joints is not well established. Three surface-mount package platforms, one with a matte Sn surface finish and the others with Ni/Au finish, were soldered to Ni/Au-finished PCB using Sn-3.0Ag- 0.5Cu (SAC305) solder, in a realistic manufacturing setting. The assembled boards were divided into three groups: one …

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

Peridynamic Models For Dynamic Brittle Fracture, Wenke Hu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Damage and failure in composite materials under dynamic loading has been extensively studied in experiments for several decades. Composite materials exhibit various damage and failure patterns under different loading rates, such as splitting and branching. Classical models cannot directly be applied to problems with discontinuous fields. A new nonlocal continuum model, peridynamics, has been proposed with the goal of solving dynamic fracture problems.

The J-integral has the physical significance of energy flow into the crack tip region. We present a rigorous derivation for the formulation of the J-integral in peridynamics using the crack infinitesimal virtual extension approach. We …

A Three-Dimensional Inverse Finite Element Analysis Of The Heel Pad, Snehal Chokhandre, Jason P. Halloran, Antonie J. Van Den Bogert, Ahmet Erdemir

Mechanical Engineering Faculty Publications

Quantification of plantar tissue behavior of the heel pad is essential in developing computational models for predictive analysis of preventive treatment options such as footwear for patients with diabetes. Simulation based studies in the past have generally adopted heel pad properties from the literature, in return using heel-specific geometry with material properties of a different heel. In exceptional cases, patient-specific material characterization was performed with simplified two-dimensional models, without further evaluation of a heel-specific response under different loading conditions. The aim of this study was to conduct an inverse finite element analysis of the heel in order to calculate heel-specific …

Flexible Residential Test Facility Instrumentation Plan, Florida Solar Energy Center, Robin Vieira

FSEC Energy Research Center®

This report provides the status of the instrumentation and a test plan for the facility. As this is the first Building America (BA) report on the facility, a description of the design and construction is included as well.

Design And Construction Of A Solar Operated Gate, Jacob Gardener

BioResource and Agricultural Engineering

This senior project discusses the design and construction of a solar operated gate. A solar panel is used to charge a battery, and then an inverter is used to run a garage door opener off the battery. The garage door opener operates a short lever arm which is connected to a longer lever arm which is connected to the gate. Each component and mounting mechanisms were designed and built to effectively provide the gate opening function. The finished product operates well, the gate opens in about 8 seconds after the button is pressed on the remote controller or wall mount …

Mechanical Integration Of A Versatile Air Suspension Into A Powered Wheelchair, Joel Michael Steinkraus

Master's Theses

Mechanical Integration of a Versatile Air Suspension into a Powered Wheelchair

Joel Steinkraus

It is undeniable that the vibration environment created by prolonged exposure to wheelchair use can cause discomfort for the rider and put him/her at risk of developing more severe medical conditions. While more research must be done to accurately quantify what constitues a harmful vibration environment, improved vibraiton isolation is an essential step. In order to incorporate structurally sound and effetive air suspension systems into motorized wheelchairs, a support structure is necessary. An after market wheelchair suspension system was designed, modeled, built and tested. Approximately 18 inches …

Pedaling And Braking Forces And Their Effect On Suspension Performance, Kathleen Kramer, Nik Goodell, Cesar Giron

Mechanical Engineering

The goal of this project is to produce a quantifiable relationship between pedaling and braking forces and suspension behavior. The test results will serve as a benchmark, against which other suspension designs can be compared in an objective, numerical manner. This report details the work completed towards determining this relationship and is primarily focused on design development of the data acquisition system and analysis of braking forces, pedaling forces and suspension response. A 2011 Specialized Stumpjumper FSR Expert Evo was used as the development platform. The system will be used to measure various rear suspension designs for comparison.