Mechanical Engineering Commons^™

Side-By-Side Testing Of Water Heating Systems: Results From The 2010-2011 Evaluation, Florida Solar Energy Center, Carlos Colon

FSEC Energy Research Center®

REVISED MARCH 2013 The Building America (BAPIRC) team at FSEC has released a report containing results from a second testing rotation (Phase II) on seven hot water systems evaluated side-by side. Results show the seasonal performance variation and compares solar systems against electric resistance and the Heat Pump Water Heater (HPWH). Standard and tankless natural gas were also evaluated, where the latter demonstrated a 24% natural gas reduction. The lowest averaged electric power consumptions were demonstrated by the HPWH (2.75 kWh/day) and the PV-pumped solar water heater (3.03 kWh/day). Other testing performed on the HPWH under conditioned and restricted air …

Weightlifting Performance Is Related To Kinematic And Kinetic Patterns Of The Hip And Knee Joints, Kristof Kipp, Josh Redden, Michelle B. Sabick, Chad Harris

Mechanical and Biomedical Engineering Faculty Publications and Presentations

The purpose of this study was to investigate correlations between biomechanical outcome measures and weightlifting performance. Joint kinematics and kinetics of the hip, knee, and ankle were calculated while ten subjects performed a clean at 85% of 1-RM. Kinematic and kinetic time-series patterns were extracted with principal components analysis. Discrete scores for each time-series pattern were calculated and used to determine how each pattern was related to body-mass normalized 1-RM. Two hip kinematic and two knee kinetic patterns were significantly correlated with relative 1-RM. The kinematic patterns captured hip and trunk motions during the first pull and hip joint motion …

On Establishing Elastic–Plastic Properties Of A Sphere By Indentation Testing, J. K. Phadikar, T. A. Bogetti, Anette M. Karlsson

Mechanical Engineering Faculty Publications

Instrumented indentation is a popular technique for determining mechanical properties of materials. Currently, the evaluation techniques of instrumented indentation are mostly limited to a flat substrate being indented by various shaped indenters (e.g., conical or spherical). This work investigates the possibility of extending instrumented indentation to non-flat surfaces. To this end, conical indentation of a sphere is investigated where two methodologies for establishing mechanical properties are explored. In the first approach, a semi-analytical approach is employed to determine the elastic modulus of the sphere utilizing the elastic unloading response (the “unloading slope”). In the second method, reverse analysis based on …

Kinematic And Kinetic Synergies Of The Lower Extremities During The Pull In Olympic Weightlifting, Kristof Kipp, Josh Redden, Michelle Sabick, Chad Harris

Mechanical and Biomedical Engineering Faculty Publications and Presentations

The purpose of this study was to identify multijoint lower extremity kinematic and kinetic synergies in weightlifting and compare these synergies between joints and across different external loads. Subjects completed sets of the clean exercise at loads equal to 65, 75, and 85% of their estimated 1-RM. Functional data analysis was used to extract principal component functions (PCF's) for hip, knee, and ankle joint angles and moments of force during the pull phase of the clean at all loads. The PCF scores were then compared between joints and across loads to determine how much of each PCF was present at …

The Influence Of Non-Equilibrium Pressure On Rotating Flows, Irfan Rashid Zardadkhan

Mechanical & Aerospace Engineering Theses & Dissertations

This study was undertaken to investigate the influence of pressure relaxation on steady, incompressible flows with strong streamline curvature. In the early part of this dissertation research, the significance of non-equilibrium pressure forces in controlling the structure of a steady, two dimensional axial vortex was demonstrated. In order to extend the study of pressure relaxation influences on more complex rotating flows, this dissertation has examined other rotating flow features that can be associated with hurricanes, tornadoes and dust devils. To model these flows, modified boundary layer equations were developed for a fluid column rotating near a solid plane including the …

Production And Characterization Of Biodegradable Nanofibers Via Forcespinning™ Technology, Zachary T. Mceachin

Theses and Dissertations - UTB/UTPA

Among the myriad of methods for polymer nanofiber production, there are only a few methods that can produce submicron range fibers in bulk from melt or solution samples. The Forcespinning™ method allows a substantial increase in sample yield; this greatly reduces the time needed to produce bulk quantities of fibers which may be critical in many fields of research and industry, in particularly in fields relating to biopolymers. The aim of the first study was to utilize this method to form non-woven mats of polycaprolactone (PCL) nanofibers and to quantitatively analyze the production and characterization of the produced fibers. The …

Nonlinear Mechanical Behavior Of The Human Common, External And Internal Carotid Arteries In Vivo, Alexey Kamenskiy, Yuris A. Dzenis, Jason N. Mactaggart, Thomas G. Lynch, Syed A. Jaffar Kazmi, Iraklis I. Pipinos

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction—The mechanical environment and properties of the carotid artery play an important role in the formation and progression of atherosclerosis in the carotid bifurcation. The purpose of this work was to measure and compare the range and variation of circumferential stress and tangent elastic moduli in the human common (CCA), external (ECA) and internal (ICA) carotid arteries over the cardiac cycle in vivo.

Methods—Measurements were performed in the surgically exposed proximal cervical CCA, distal ECA and distal ICA of normotensive patients (n = 16) undergoing carotid endarterectomy. All measurements were completed in vivo over the cardiac cycle …

Design And Implementation Of The Kinect Controlled Electro-Mechanical Skeleton (K.C.E.M.S), Jason Richard Ekelmann

Doctoral Dissertations and Master's Theses

Mimicking real-time human motion with a low cost solution has been an extremely difficult task in the past but with the release of the Microsoft Kinect motion capture system, this problem has been simplified. This thesis discusses the feasibility and design behind a simple robotic skeleton that utilizes the Kinect to mimic human movements in near real-time. The goal of this project is to construct a 1/3-scale model of a robotically enhanced skeleton and demonstrate the abilities of the Kinect as a tool for human movement mimicry. The resulting robot was able to mimic many human movements but was mechanically …

Modeling, Identification, Validation And Control Of A Hybrid Maglev Ball System, Ahmed Elhussein E. Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, the electrodynamics of a single axis hybrid electromagnetic suspension Maglev system was modeled and validated by applying it to a single axis hybrid maglev ball experiment. By exploring its linearized model, it was shown that the single axis hybrid Maglev ball has inherently unstable dynamics. Three control scenarios were explored based on the linearized model; (1) Proportional, Deferential (PD) control, (2) Proportional, Deferential, Integral (PID) and (3) PID controller with pre-filtering. This thesis has shown that a PID controller with a pre-filtering technique can stabilize such a system and provide a well-controlled response.

A parametric system identification …

Ergonomic Design Of An Aerial Bucket For Ingress And Egress, Bianca M. Bain

Master's Theses (2009 -)

Electric utility companies across the US have been using aerial bucket trucks for line work and troubleshooting for decades. The use of these trucks eliminates the need for workers to climb utility poles in order to repair or maintain lines. Poor ingress and egress design can lead to acute injuries (slips and falls) as well as cumulative injury (musculoskeletal disorders (MSDs)). Utility companies want to know the best combination of steps and handlebars for aerial bucket ingress and egress that would minimize the risk of injury. American National Standards Institute (ANSI) standard – ANSI/SIA A92.2-2009, sets design requirements for aerial …

Analysis Of Mechanically Milled Exchange Coupled Nanocomposite Permanent Magnets, Santanu Mukherjee

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Nanocomposite permanent magnets have recently evoked wide interest because of their interesting properties. They usually consist of a hard magnetic phase having superior coercivities and a soft magnetic phase having improved values of magnetization and when they are coupled together, we get a permanent magnet with enhanced values of both the parameters and thus can be put to a lot of applications. Also to make this possible we can take advantage of the principle of exchange interaction which has been discussed subsequently in detail.

Also the microstructure plays a major role in obtaining good magnetic properties and the microstructure is …

Propagation Of Ultrasound Through Freshly Excised Human Calvarium, Armando Garcia Noguera

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The propagation of ultrasound through complex biological media, such as the human calvarium, poses a great challenge for modern medicine. Several ultrasonic techniques commonly used for treatment and diagnosis in most of the human body are still difficult to apply to the human brain, in part, because of the properties of the skull. Moreover, an understanding of the biomechanics of transcranial ultrasound may provide needed insight into the problem of blast wave induced traumatic brain injury (TBI). In the present study, the spatial variability of ultrasonic properties was evaluated for relevant frequencies of 0.5, 1, and 2.25 MHz. A total …

Dynamic Model Of Sailors Descending A Navy Ship Ladder, Jonathan Coulter

Mechanical & Aerospace Engineering Theses & Dissertations

Knee moments are greater in individuals who climb Navy ship ladders than in people climbing stairs. Because it is known that people who climb stairs frequently are at greater risk for osteoarthritis and that people in the Navy report higher incidences of knee pain, it was hypothesized that the internal joint reaction forces during the sailor's descent of a ship ladder would be greater than internal joint reaction forces of gait and stair climbing. Dimensions of a commonly used Navy ship ladder were collected and a replica was constructed. The replica was instrumented to collect 3D kinematics and kinetics during …

Numerical Analysis And Design Optimization Of Organic Bulk Hetero-Junction Solar Cells Using The Mixed Finite Element And Arc-Length Methods, James L. Dean

Mechanical & Aerospace Engineering Theses & Dissertations

Due to the high coupling and non-linear nature of the semiconductor equations, numerical stability becomes a major problem when using a purely Newtonian numerical method in solving these equations. Presented is a robust mixed finite element formulation with application for organic solar cell devices that incorporates the arc-length predictor-corrector method to bypass such stability issues. The simulated device represents a multilayered solar cell using organic bulk hetero-junction materials including donor materials Poly[2,1,3-benzothiadiazole-4,7-diyl[4,4-bis(2-ethylhexyl)-4H-cyclopenta[2,1-b:3,4- b']dithiophene-2,6-diyl]] (PCPDTBT) and poly 3-hexylthiophene (P3HT) with acceptor fullerene materials [6,6]-phenyl C61 butyric acid methyl ester (PC61BM) or [6,6]-phenyl C71 butyric acid methyl ester (PC71BM) as the photoactive …

Kinematic Analysis Of Gesture In Aphasia, Haroon Osmanzada

Mechanical & Aerospace Engineering Theses & Dissertations

Individuals who have experienced a left hemispheric stroke often develop aphasia, which results in a loss of effective verbal communication and reliance on gesturing to communicate. In this study we combined these two aspects of aphasic word retrieval difficulties and gesturing with three-dimensional kinematics. The purposes of this study were: 1) to develop a preliminary database of upper extremity movements for two common gestures used in gestural facilitation of naming (GES) training, slicing and hammering, in participants who experienced a left-hemisphere stroke and compare them to age-matched healthy controls, and 2) to perform a case study consisting of a single …

Analysis Of Bar Deformation Under Sternum Forces During Surgical Correction Of Pectus Excavatum In Children, Rohit N. Nikam

Mechanical & Aerospace Engineering Theses & Dissertations

Pectus excavatum (PE) also known as sunken or funnel chest is the most common chest wall deformity and affects 1 in every 1,000 children. In PE patients, the middle lower portion of the sternum is depressed producing concave appearance of the anterior part of the chest wall. This problem can be corrected with minimally invasive surgery developed by Dr. Donald Nuss in 1986. A specially made steel bar is implanted to lift the sternum to its normal position. This technique has been modified several times to improve safety and effectiveness of the bar placement and removal. One of the significant …

Evaluation Of Autonomous Robotic Milling Methodology For Natural Tooth-Shaped Implants Based On Sko Optimization, Yongki Yoon

Mechanical & Aerospace Engineering Theses & Dissertations

Robotic surgery is one of the most demanding and challenging applications in the field of automatic control. One of the conventional surgeries, the dental implantation, is the standard methodology to place the artificial tooth root composed of titanium material into the upper or lower jawbone. During the dental implant surgery, mechanical removal of the bone material is the most critical procedure because it may affect the patient's safety including damage to the mandibular canal nerve and/or piercing the maxillary sinus. With this problem, even though short term survival rates are greater than 95%, long term success rate of the surgery …

Re-Evaluation Of Resistance Prediction For High-Speed Round Bilge Hull Forms, Jae Won

Theses and Dissertations

Predicting the resistance of a high-speed monohull has been of interest to Naval Architects for several decades. Even though considerable amount of research has been carried out in this area, there remains a degree of uncertainty in the accurate resistance prediction in the early design stage. This research thesis attempts to investigate a method for enhancing the accuracy of resistance prediction methods for high-speed round-bilge monohull form vessels for a wide range of volumetric Froude numbers (Fn). While a number of systematic series are in existence, their data are either not readily available or scattered in various internal reports and …

Final Technical Report (2nd Revision) Arra: Florida Energy Code Compliance Train-The-Trainer Program, Florida Solar Energy Center, Jeffrey Sonne

FSEC Energy Research Center®

A multi-faceted Florida Energy Code compliance methods, tools and field verification training program was established that included development of two instructor-led and two web-based courses, instructor training and course development support, and training of building officials and contractors throughout the state.

Separate instructor-led commercial and residential 2010 Florida Energy Code compliance courses were developed for train-the-trainer class use, and existing instructor-led blueprints data collection and energy code software courses were redeveloped as web-based courses.

Through partnerships with Florida colleges, building departments and industry organizations, a total of 42 instructors were trained to provide commercial energy code compliance training and 42 …

Investigation Of Compliant Space Mechanisms With Application To The Design Of A Large-Displacement Monolithic Compliant Rotational Hinge, Robert Mcintyre Fowler

Theses and Dissertations

The purpose of this research is to investigate the use of compliant mechanisms in space applications and design, analyze, and test a compliant space mechanism. Current space mechanisms are already highly refined and it is unclear if significant improvements in performance can be made by continuing to refine current designs. Compliant mechanisms offer a promising opportunity to change the fundamental approach to achieving controlled motion in space systems and have potential for dramatic increases in mechanism performance given the constraints of the space environment. A compliant deployment hinge was selected for development after industry input was gathered. Concepts for large-displacement …