Manufacturing Commons^™

The Investigation Of The Underlying Microstructure Associated With Fracture Features In 6061 Cold Sprayed Aluminum, Justin White

UNF Graduate Theses and Dissertations

Cold gas dynamic spraying commonly known as cold spray is a process currently used for restoration, re-tolerancing, and application of coatings. With additional resources allocated towards the development of a through process model aimed at predicting the properties of bulk material produced via the Cold Spray process, more lab testing and investigation must be done to capture the effects of the varying microstructure in CS materials. The properties of ultra-fine-grained materials are derived from data collected from coarse grained materials and processes that do not accurately capture the effects as elevated strain rates and ultra-fine-grained materials. The lack of property …

Material Handling System For An Advanced Flexible Manufacturing Environment, Con Cronin

Theses

A Flexible Manufacturing System (FMS) is a method of production that is designed to easily adapt to changes in the type and quantity of the product being manufactured. Machines and computerised systems can be configured to manufacture a variety of parts and to handle the changing levels of production that is required. The aim of this project was to investigate the current manufacturing processes of Kostal Ireland GmbH with the aim of developing a bespoke prototype material handling system to achieve flexible manufacturing. Kostal Ireland GmbH currently do not have the ability to change their manufacturing operations easily when a …

Rheology Of Particulate Suspensions With Non-Newtonian Fluids In Capillaries, Bin Xia, Paul Krueger

Mechanical Engineering Research

This resource contains the processed experimental measurements of the flow consistency index and flow behavior index, along with their trendlines, for the particulate suspensions investigated in "Rheology of Particulate Suspensions with Non-Newtonian Fluids in Capillaries" by Bin Xia and Paul S. Krueger.

Generic Design Methodology For Smart Manufacturing Systems From A Practical Perspective, Part I—Digital Triad Concept And Its Application As A System Reference Model, Zhuming Bi, Wen-Jun Zhang, Chong Wu, Chaomin Luo, Lida Xu

Information Technology & Decision Sciences Faculty Publications

Rapidly developed information technologies (IT) have continuously empowered manufacturing systems and accelerated the evolution of manufacturing system paradigms, and smart manufacturing (SM) has become one of the most promising paradigms. The study of SM has attracted a great deal of attention for researchers in academia and practitioners in industry. However, an obvious fact is that people with different backgrounds have different expectations for SM, and this has led to high diversity, ambiguity, and inconsistency in terms of definitions, reference models, performance matrices, and system design methodologies. It has been found that the state of the art SM research is limited …

Base Vibration Effects On Additive Manufactured Part Quality: A Study Of 3d Printing Onboard U.S. Navy Ships, Nick Jensen

Dissertations, Master's Theses and Master's Reports

The current landscape of manufacturing is evolving because of technology like additive manufacturing (AM). The mobility and compactness of AM are what make it desirable for many industry sectors. The U.S. Navy has shown interest in deploying AM on ships as it could alleviate their dependency on off-route docking to recharge supplies. However, the U.S. Navy's aspiration is currently hindered due to harsh ship-borne environments that degrade AM part quality.

This thesis focuses on vertical base vibration effects on AM part quality. An introduction is first given in Chapter 1 to familiarize the reader with the U.S. Navy's predicament. The …

A Machine Vision Based Automated Quality Control System For Product Dimensional Analysis, Aditya Akundi, Mark Reyna

Manufacturing & Industrial Engineering Faculty Publications

Quality control (QC) in manufacturing processes is critical to ensuring consumers receive products with proper functionality and reliability. Faulty products can lead to additional costs for the manufacturer and damage trust in a brand. A growing trend in QC is the use of machine vision (MV) systems because of their noncontact inspection, high repeatability, and relatively low cost. This paper presents a robust MV system developed to perform comparative dimensional inspection on diversely shaped samples, including additive manufacturing products. The algorithm used performs dimensional inspection on a base product considered to have acceptable dimensions. The perimeter, area, rectangularity, and circularity …

A Review On Application Of Model Based Systems Engineering To Manufacturing And Production Engineering Systems, Aditya Akundi, Viviana Lopez

Manufacturing & Industrial Engineering Faculty Publications

Increasing complexity in today’s manufacturing and production industry due to the need for higher flexibility and competitiveness is leading to inconsistencies in the iterative exchange loops of the system design process. To address these complexities and inconsistencies, an ongoing industry trend for organizations to make a transition from document-centric principles and applications to being model-centric is observed. In this paper, a literature review is presented highlighting the current need for an industry-wide transition from document-centric systems engineering to Model-Based Systems Engineering (MBSE). Further, investigating the tools and languages used by the researchers for facilitating the transition to and the integration …

Potential Production Of Theranostic Boron Nitride Nanotubes (64cu-Bnnts) Radiolabeled By Neutron Capture, Wellington Marcos Silva, Helio Ribeiro, Jaime Taha-Tijerina

Manufacturing & Industrial Engineering Faculty Publications

In this work, the radioisotope 64Cu was obtained from copper (II) chloride dihydrate in a nuclear research reactor by neutron capture, (63Cu(n, )64Cu), and incorporated into boron nitride nanotubes (BNNTs) using a solvothermal process. The produced 64Cu-BNNTs were analyzed by TEM, MEV, FTIR, XDR, XPS and gamma spectrometry, with which it was possible to observe the formation of64Cu nanoparticles, with sizes of up to 16 nm, distributed through nanotubes. The synthesized of 64Cu nanostructures showed a pure photoemission peak of 511 keV, which is characteristic of gamma radiation. This type of emission is desirable for Photon Emission Tomography (PET scan) …

Modeling And Optimization Of Process Parameters In Face Milling Of Ti6al4v Alloy Using Taguchi And Grey Relational Analysis, Al Mazedur Rahman, S M Abdur Rob, Anil K. Srivastava

Manufacturing & Industrial Engineering Faculty Publications

Titanium alloys are extensively used in aerospace, missiles, rockets, naval ships, automotive, medical devices, and even the consumer electronics industry where a high strength to density ratio, lightweight, high corrosion resistance, and resistance to high temperatures are important. The machining of these alloys has always been challenging for manufacturers. This article investigates the combined effect of radial depth, cutting speed and feed rate on cutting forces, tool life, and surface roughness during face milling of Ti6Al4V alloy. This study focuses on the significance of radial depth of cut on cutting force, tool life and surface roughness compared to that of …

El Español En Estados Unidos Como Recurso Para La Educación De Hispanos En Ingeniería, Hiram Moya

Manufacturing & Industrial Engineering Faculty Publications

Los Hispanos representan la más grande minoría en Estados Unidos. Sin embargo, el número de estudiantes hispanos en las carreras de ciencias y en particular en ingeniería ha estado subrepresentada por muchos años. Esta falta de representación ha hecho que se estudie de muchas formas los métodos de reclutar y retener y graduar estudiantes hispanos en ingeniería. Sin embargo, la urgencia continúa. Existen muchos retos para mejorar la participación de hispanos en ingeniería, incluyendo la falta costumbre en preguntar o solicitar ayuda, los retos económicos, y la falta de ejemplos a seguir en la facultad. Dado los retos, este artículo …

Advance Metallic Reinforcement Of Vat Photo Polymerized Parts, Scott Zinn

UNF Graduate Theses and Dissertations

The metallization or metallic reinforcement of polymer parts has been widely used in industry for several decades. Polymer parts are classically metalized for aesthetics, chemical and thermal resistance, electrical conductivity, and mechanical strength. Metallization has been shown to increase strength of polymer parts when compared to the strength of the bulk material without metallization. Additive manufacturing (AM) techniques that have emerged in the last few decades produce parts with different surface features and chemistry than the typical polymer part produced through injection molding. AM parts are typically weaker than traditionally manufactured parts from the same material due to intrinsic details …

Digital Twins For Manufacturing And Logistics Systems: Is Simulation Practice Ready?, Francesco Longo, Antonio Padovano, Letizia Nicoletti, Mohaiad Elbasheer, Rafael Diaz

VMASC Publications

This article provides a theoretical contribution to the state-of-the-art of digital twins for manufacturing and logistics systems. The primary goal of this paper is to draw attention to the gap between the theoretical framework of digital twins in manufacturing and supply chain and their practical implementation from a simulation modeling point of view. Therefore, highlighting the recent innovations in the simulation practice that could provide the basis for digital twins with high levels of data integration, automation, and smart capabilities. This study follows a comparative approach to analyzing theoretical and technical readiness for developing digital twins with high fidelity and …

Generic Design Methodology For Smart Manufacturing Systems From A Practical Perspective. Part Ii—Systematic Designs Of Smart Manufacturing Systems, Zhuming Bi, Wen-Jun Zhang, Chong Wu, Chaomin Luo, Lida Xu

Information Technology & Decision Sciences Faculty Publications

In a traditional system paradigm, an enterprise reference model provides the guide for practitioners to select manufacturing elements, configure elements into a manufacturing system, and model system options for evaluation and comparison of system solutions against given performance metrics. However, a smart manufacturing system aims to reconfigure different systems in achieving high-level smartness in its system lifecycle; moreover, each smart system is customized in terms of the constraints of manufacturing resources and the prioritized performance metrics to achieve system smartness. Few works were found on the development of systematic methodologies for the design of smart manufacturing systems. The novel contributions …

Balancing Trade-Offs In One-Stage Production With Processing Time Uncertainty, Jingjing You

Theses and Dissertations--Mechanical and Aerospace Engineering

Stochastic production scheduling faces three challenges, first the inconsistencies among key performance indicators (KPIs), second the trade-offs between the expected return and the risk for a portfolio of KPIs, and third the uncertainty in processing times. Based on two inconsistent KPIs of total completion time (TCT) and variance of completion times (VCT), we propose our trade-off balancing (ToB) heuristic for one-stage production scheduling. Through comprehensive case studies, we show that our ToB heuristic with preference =0.0:0.1:1.0 efficiently and effectively addresses the three challenges. Moreover, our trade-off balancing scheme can be generalized to balance a number of …

Tailoring Texture, Microstructure, And Shape Memory Behavior Of Niti Alloys Fabricated By L-Pbf-Am, Sayed Ehsan Saghaian N.E.

Theses and Dissertations--Mechanical and Aerospace Engineering

Laser Powder Bed Fusion (L-PBF) is one of the most promising Additive Manufacturing (AM) methods to fabricate near net-shape metallic materials for a wide range of applications such as patient-specific medical devices, functionally graded materials, and complex structures. NiTi shape memory alloys (SMAs) are of great interest due to a combination of unique features, such as superelasticity, shape memory effect, high ductility, work output, corrosion resistance, and biocompatibility that could be employed in many applications in automotive, aerospace, and biomedical industries. Due to the difficulties with traditional machining and forming of NiTi components, the ability to fabricate complex parts, tailor …

Redesigning Products To Optimize Sustainable Performance In Multi-Generational Closed-Loop Production For Advancing The Circular Economy, Buddhika Minendra Hapuwatte

Theses and Dissertations--Mechanical and Aerospace Engineering

Sustainable manufacturing and the circular economy concepts promote efficient and effective resource use to minimize the adverse economic, environmental, and social impacts of alarmingly increasing consumption rates. Product design is the key to implement these transformations in manufacturing. However, the currently available sustainable and circular design methods are not comprehensive and inadequate—especially for multi-generational products. Therefore, designing sustainable products optimized for circular and closed-loop production systems is a challenging task. The 6Rs concept introduced ‘Redesign’ to modify a product’s engineering specifications and allow sustainable utilization of the end-of-use resources from previous generations, thus closing the production loop. Therefore, the objective …

Additive Manufacturing In Personalized Medicine: Patient-Customized Solid Dose Medicines, And Patient-Customized Wound Care Device, Amir Najarzadeh

Theses and Dissertations--Mechanical and Aerospace Engineering

Personalized Medicine - from a one-size fits all to a tailored approach is the future in pharmaceutical therapeutics and medical applications. The aim of this study is demonstrate additive manufacturing in two personalized medicine applications: 1. Patient- customized solid dose medicines, and 2. Patient-customized wound care device. The aim of the first application is to develop an inexpensive and accurate method to design and fabricate patient-customized tablets. Particularly this paper focuses on fabricating and dose controlling of patient-customized extended release prednisolone-poly(vinyle alcohole) PVA. Dry-Blending, Wet Granulation, Extrusion, Spherionization, Hot melt extrusion (HME) was adopted to produce drug loaded prednisolone-PVA filaments …

Thermomechanical Mechanisms That Cause Adhesion Of Aluminum High Pressure Die Castings To The Die, Alex Monroe

Dissertations, Master's Theses and Master's Reports

In high pressure die casting (HPDC) of aluminum, cast material adhering to die is a significant defect. Adhesion occurs in two primary ways. The casting may stick preventing its removal from the die. Aluminum can also adhere to the die and buildup in local areas on the die surface with additional casting cycles. This second form of adhesion is called soldering. Lubricant is the best technology to control all forms of adhesion, but it comes at the cost of casting porosity, blisters, reduced die life, and increased die casting machine wear. New strategies to prevent adhesion are desired to eliminate …

Defect Detection Using Dynamic Analysis For Additive Manufactured Metals, Gita Deonarain

Dissertations, Master's Theses and Master's Reports

Additive manufacturing (AM) has the ability to produce parts with complex geometries and internal features, however, for demanding applications such as the automotive and aerospace industries, it is crucial that the parts can meet the demanding functional and geometric requirements. Quality control for AM parts focuses on nondestructive methods of testing, but many of the current methods are expensive and time-consuming. The research presented in this report explores various methods of nondestructive evaluation (NDE) using dynamic analysis on stainless steel parts produced with selective laser melting (SLM). Methods include, but are not limited to, frequency response functions (FRF), impedance-based measurements, …

Model-Based Predictive Controller Design, Soheil Sadeghi

Graduate Research Papers

Process control in industries is becoming more critical due to demands on reducing consumed energy, reducing cost, and improving system efficiency and performance. In this work, a well-developed, model-based controller is introduced and implemented in one of the most common processes in the industry. Model Predictive Controller (MPC) has been studied for ten years, but recently has emerged into small industries as the number of current applications grows. These controllers need a process model in the forms of transfer functions, step response, or state-space. Although obtaining a process model can be a cumbersome task, it is worth having it (the …