Heat Transfer, Combustion Commons^™

Designing A Heat Sink For Lithium-Ion Battery Packs In Electric Vehicles, Dylan Irvine, Evan Foreman, Christopher B. Remington, Aaron Jackson, Sam Endrizzi

Williams Honors College, Honors Research Projects

This report addresses the concepts and implementation of fluid cooled heat sink designs for an electric or hybrid vehicle battery. To determine the battery’s temperature and heat flux profile, testing was performed by measuring these values at multiple locations on a lithium-ion pouch battery using heat flux sensors and thermocouples during the charge and discharge cycles of the battery. Once the data was collected and analyzed, trendlines were fit to the heat flux data then used to create equations for the heat flux profile during the discharging stage. Each equation represented a specific region on the battery geometry. Four heat …

2015 Afrl University And Service Academy Design Challenge, Andrew P. Killmeyer, Jacob Stein, Casey Hale, Jeff Quartermaine, Kevin Rolik, Brandon Null, Nick Tsangeos, Marissa Seeley, Sam Moats, Nicholas Garafolo Phd, Daniel Slattery

Williams Honors College, Honors Research Projects

The University of Akron’s Air Force Research Laboratory’s Design Challenge Team has engineered a Heat Stress Prevention Kit that includes a facial mask in which the soldier will cool down from the inside out by breathing in the cool air circulating throughout the mask. This cool air is produced from a thermoelectric chip, which has a specific temperature difference on either side, one hot and one cold. Each of the sides are isolated from one another and with the combination of heatsinks, fans, and the simple process of breathing, a system is created by inhaling cool air. The entire system …

Design Of An Sae Baja Racing Off-Road Vehicle Powertrain, Eric T. Payne

Williams Honors College, Honors Research Projects

No abstract provided.

Computational Fluid Dynamics Modeling Of The Effects Of Water Injection In A Diesel Engine, Rabun Z. Wallace

College of Graduate Studies: Theses & Dissertations

Water injection has been used in internal combustion engines for many years. It has been used to cool combustion temperatures, reduce emissions, and in some instances clean carbon buildup from the cylinder. Research has shown that the water to fuel mass ratio is most effective between 20-30%, so the upper and lower limit were used for simulations in Converge CFD. To validate the CFD model, a case without water injection was compared to experimental data from Sandia National Laboratory. The predicted in-cylinder pressure and heat release rate showed good agreement with the experimental data. Cases were run with the injection …

Evaporative Techniques For Stormwater Runoff Alleviation, Allison M. Arnold

Graduate Theses, Dissertations, and Problem Reports (ETD)

Current climate changes have led to a projected steady increase in rainfall over the next several decades, notably in the Greater Pittsburgh Area. Even without this predicted increase the urbanization of many regions has altered local natural environments, which in the past stored, shed and evaporated this runoff water effectively, maintaining balance within the water table. These added rainfall forecasts, combined with America’s growing trend to develop and expand the urbanization of our natural earth, has resulted in a growing surplus of stormwater runoff water affecting these cities and their suburbs, leaving many sanitation departments unable to meet the heightened …

Heat Transfer Enhancement And Applications Of Femtosecond Laser Processed Metallic Surfaces, Corey M. Kruse

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, functionalized 304 stainless steel metallic surfaces were created with the use of a Femtosecond Laser Surface Processing (FLSP) technique. The laser processing technique produces self-organized micro/nanostructures on the surface. The heat transfer performance of various FLSP functionalized surfaces were characterized through pool boiling and Leidenfrost experiments. Enhancement in both the nucleate and film boiling heat transfer were observed through an increase of the critical heat flux and heat transfer coefficient as well as shifts in the Leidenfrost temperature respectively. For both experiments, a polished reference sample was used as a baseline line to compare against the …

Temperature Controlled Packaging Container For Biologics And Pharmaceuticals, Melinda Phan, Yufay Chow-Yee, Abraham Ho

Mechanical Engineering

Clinical Supplies Management, Inc. (CSM) provides clinical trial services to biotechnology and pharmaceutical companies by shipping pharmaceuticals to clinics and other patients. In winter 2014, CSM presented a temperature control packaging project to the Cal Poly Senior Project class. As a result, three Cal Poly Mechanical Engineering Students were tasked to design, manufacture, and qualify a shipping container that would maintain ten 10 mL vials between 2-8°C for 96 hours. The final product would have to cost less to ship than the Credo Cube, CSM’s current temperature control packaging product. After considerable research and analysis on possible temperature control technologies, …

Mhttu Implementation Final Project Report, Angelica Ramirez, Julian Samayoa, Matt Keeble

Mechanical Engineering

Lawrence Livermore National Laboratory has invested considerable effort in developing fireproof high-efficiency particulate air (HEPA) filters. Due to the nature of LLNL’s research, the air leaving its lab facilities must be filtered before it is released into the atmosphere; thus, each laboratory is equipped with large banks of HEPA filters through which all internal air is exhausted. Over the years, however, fires have erupted in the labs and entire banks of HEPA filters have been destroyed, resulting in repairs and crucial downtime that prove costly.

Engineers and scientists alike have been seeking a permanent solution to this problem, and one …

Inverse Volume-Of-Fluid Meshless Method For Efficient Non-Destructive Thermographic Evaluation, Hussein Awad Kurdi Saad

Doctoral Dissertations and Master's Theses

A novel computational tool based in the Localized Radial-basis Function (RBF) Collocation (LRC) Meshless method coupled with a Volume-of-Fluid (VoF) scheme capable of accurately and efficiently solving transient multi-dimensional heat conduction problems in composite and heterogeneous media is formulated and implemented. While the LRC Meshless method lends its inherent advantages of spectral convergence and ease of automation, the VoF scheme allows to effectively and efficiently simulate the location, size, and shape of cavities, voids, inclusions, defects, or de-attachments in the conducting media without the need to regenerate point distributions, boundaries, or interpolation matrices. To this end, the Inverse Geometric problem …

Host-Guest Interaction Dictated Selective Adsorption And Fluorescence Quenching Of A Luminescent Lightweight Metal-Organic Framework Toward Liquid Explosives, Dan Liu, Xiaojuan Liu, Yongxin Liu, Yang Yu, Fanglin Chen, Cheng Wang

Faculty Publications

In this article, we report the successful preparation of a Mg-based luminescent MIL-53 metal–organic framework (MOF), namely [Mg2(BDC)2(BPNO)]·2DMF (1) (BDC = 1,4-benzene dicarboxylate, BPNO = 4,4’- dipyridyl-N,N’-dioxide, DMF = N,N-dimethylformamide) in a mixed solvent containing a 2 : 3 volume ratio of DMF and ethanol (EtOH) under solvothermal conditions. Desolvated compound 1a can be used as an absorbent for selective adsorption and separation of liquid explosives, including nitroaromatic (nitrobenzene (NB)) and nitroaliphatic (nitromethane (NM) and nitroethane (NE)) compounds, through single crystal-to-single crystal (SC–SC) transformations. As one of the weakly luminescent MOFs, the luminescence of compound 1a could be quenched by …

Unsteady Flamelet Progress Variable Modeling Of Reacting Diesel Jets, Muhsin Mohammed Ameen

Open Access Dissertations

Accurate modeling of turbulence/chemistry interactions in turbulent reacting diesel jets is critical to the development of predictive computational tools for diesel engines. The models should be able to predict the transient physical and chemical processes in the jets such as ignition and flame lift-off. In the first part of this work, an existing unsteady flamelet progress variable (UFPV) model is employed in Reynolds-averaged Navier-Stokes (RANS) simulations and large-eddy simulations (LES) to assess its accuracy. The RANS simulations predict that ignition occurs toward the leading tip of the jet, followed by ignition front propagation toward the stoichiometric surface, and flame propagation …

Applied Energy Systems - Rudimentary Thermodynamics, Jim Mcgovern

Book/Book Chapters

This is a compact textbook for a module addressing rudimentary thermodynamics within the context of applied energy systems. It is at an introductory level for engineers or technologists. The book does not attempt to cover the principles of thermodynamics comprehensively. Rather, it provides a practical but theoretically sound foundation, linked to some key areas. Energy, heat and work are all introduced, as are units and dimensions. Ideal gases and properties of liquids and vapours are treated. Non-flow and steady flow processes are described. Simple theory is provided for pumps and for the reciprocating compressor. Rudimentary steam and refrigeration or heat …

Natural Convection From Circular Cylinders, Sandra K. S. Boetcher

Publications

Chapter 1

Natural convection heat transfer from circular cylinders in quiescent environments is a subject which has been studied extensively. Although a well-established topic, to the best knowledge of the author no single source of reference is found for natural convection from circular cylinders for varying orientations (horizontal, vertical, and inclined). This book attempts to be a reference for Nusselt number correlations for circular cylinders of all inclinations including horizontal and vertical.

Thermal Properties Of Soft Nanomaterials: Materials Synthesis And Fabrication, Meng Pan, Collier Miers, Amy Marconnet, Yu Han

The Summer Undergraduate Research Fellowship (SURF) Symposium

The properties of soft nanomaterials are hard to measure exactly due to their mechanical properties and unstable shape. In particular, hydrogels are a class of cross-linked polymers that can absorb large quantities of water changing their shape under the influence of various conditions such as humidity, temperature, and pH. This research addresses the fabrication of a material that has a significant contrast in properties under different conditions (e.g. temperature, wetting, and pH) and determine the physical mechanisms of heat transfer in this nanomaterial. The hydrogels are made using a several cycles of a freeze-thaw method. The method requires soluble material. …

Radiation Measurements And Data Analysis Of Turbulent Premixed Lean Flame, Yunzhe Yang, Dong Han, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

An accurate understanding of the radiation transfer in turbulent premixed lean flame is critical for improving energy efficiencies and reducing emissions such as nitric oxide and soot. Radiation measurement is an effective and nonintrusive way to study the radiation properties of turbulent premixed lean flames. In this study, a high-speed infrared camera was utilized to measure the planar radiation from turbulent premixed lean flames under different conditions. Time-dependent flame images were acquired and radiation statistics were calculated and compared to investigate the effects of equivalence ratio, heat release rate, hydrogen pilot flame rate, and co-flow rate on the radiation intensity …

The Role Of Surface Area In Catalytic Gasification Of Biomass, Elizabeth A. Wachs, Nitish Kumar, Indraneel Sircar, Prithviraja Basak, Jay P. Gore Phd

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gasification of biomass has the potential to provide a carbon-negative source of liquid fuels. The current limited use of gasification is due in part to the high temperatures necessary to achieve high conversion levels. These temperatures can be lowered by the use of catalysts, but the mechanisms by which catalysts affect the reaction rate are not fully understood. Here, the structural component of potassium carbonate’s role in the gasification process was examined. Samples of pinewood sawdust were impregnated with potassium carbonate, then pyrolyzed with N2 in a fixed bed reactor at 750°C (heater thermocouple reading). Half of the char was …

Preliminary Testing Of Plasma-Induced Combustion, Ahmed Thalib Razi, Carson Slabaugh, Robert Lucht

The Summer Undergraduate Research Fellowship (SURF) Symposium

Plasma-induced combustion (PIC) has been shown to improve the reliability, efficiency, and delay time of ignition in flight systems like augmentors and scramjets. These high-velocity systems are mostly used in military applications, and improvement may help commercial viability. To understand this chemical process, the concentration of radicals, particularly H radicals, must be tracked through the flame using laser diagnostics. This requires a steady source of plasma-assisted combustion to be secured and well-understood. A plasma torch flowing partially premixed air and methane was installed and successfully operated, and preliminary testing was carried out. Primarily it was observed that PIC created stable …

Thermal Properties Of Soft Nanomaterials: Thermal Measurement Design, Yu Han, Meng Pan, Amy Marconnet, Collier Miers

The Summer Undergraduate Research Fellowship (SURF) Symposium

Soft materials like hydrogels have multiple tunable material properties because of their unique structures. Due to the ability to respond to stimuli like temperature or chemical environment, they have numerous applications in different fields like delivering drugs inside the human body and other medical uses. Details of the thermal transport mechanisms, as well as the overall thermal properties, are critical for a variety of applications. Multi-property measurements elucidate the underlying transport mechanisms in the soft materials. This research demonstrates a new methodology of measuring thermal properties of soft materials. This work uses the 3w method [1,2] for measuring the thermal …

Minimization Of The Effects Of Secondary Reactions On Turbine Film Cooling In A Fuel Rich Environment, Andrew T. Shewhart

Theses and Dissertations

The demand for increased thrust, higher engine efficiency, and reduced fuel consumption has increased the turbine inlet temperature and pressure in modern gas turbine engines. The outcome of these higher temperatures and pressures is the potential for unconsumed radical species to enter the turbine. Because modern cooling schemes for turbine blades involve injecting cool, oxygen rich air adjacent to the surface, the potential for reaction with radicals in the mainstream flow and augmented heat transfer to the blade arises. This study evaluated various configurations of multiple cylindrical rows of cooling holes in terms of both heat release and effective downstream …

Formula Sae Cooling System Design, Lisa Van Den Berg, Brandon Lofaro

Mechanical Engineering

The overall objective of this senior project is to develop, via testing and analysis, a guided process that will aid the Cal Poly Formula SAE team in designing their cooling system. More specifically, a set of designed tests will yield the results necessary in determining a combination of fan and radiator that will achieve appropriate cooling.

A test section that has the capability of interfacing with both the wind tunnel in the Thermal Science Lab and a radiator will be used to facilitate the necessary experiments. The wind tunnel is powered by fan controlled by a variable frequency drive that …