Heat Transfer, Combustion Commons^™

Transient And Quasi-Steady Thermal Behaviour Of A Building Envelope Due To Retrofitted Cavity Wall And Ceiling Insulation, Aimee Byrne, Gerard Byrne, Anna Davies, Anthony Robinson

Articles

Accurate understanding of the thermal behaviour of building components is essential for predicting heat-ing or cooling needs and facilitates the implementation of more successful energy saving strategies and retrofits. This paper focuses on a specific measure commonly introduced through the residential energy efficiency retrofit programmes in Ireland–insulation. Traditionally, assessments of the performance of building envelopes have been based on assumed thermal resistances of the materials involved, labora-tory tests and computer modelling. The aim of the present work is to investigate the in situ thermal behaviour of a case study building and its components under transient and quasi-steady environmental conditions, comparing …

Numerical Analysis Of The Thermodynamic Properties Of Various Gaseous Species, Addison Alexander

Lewis Honors College Capstone Collection

In the field of Fluid Mechanics, the determination of various thermodynamic properties of substances is of utmost importance. Many calculations require values for internal energy or specific heats. If experimental data does not exist to facilitate these calculations, an approximation must be made. This report analyzes three different approximation approaches to examine their relative strengths and weaknesses. The first approach, the Exact Method, uses NASA thermodynamic data to give a numerical interpolation. The second, the Summation Method, breaks up the total energy of the species into different contributions and performs an approximation based on thermodynamic theory. Finally, the Spectroscopic Method …

A Simplified Model Of The Internal Combustion Engine, Christofer Neff

Undergraduate Journal of Mathematical Modeling: One + Two

This project further investigates a model of a simplified internal combustion engine considered by Kranc in 1977. Using Euler’s method for ordinary differential equations, we modeled the interaction between the engine’s flywheel and thermodynamic power cycle. Approximating with sufficiently small time intervals (0.001 seconds over a period of 12 seconds) reproduced Kranc’s results with the engine having an average angular velocity of 72/sec.

Assessing And Mitigating Airborne Noise From Power Generation Equipment, Limin Zhou

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation examines the assessment and mitigation of airborne noise from power generation equipment.

The first half of the dissertation investigates the diagnosis and treatment of combustion oscillations in boilers. Sound is produced by the flame and is reflected downstream from the combustion chamber. The reflected sound waves perturb the mixture flow or equivalence ratio increasing the heat release pulsations and the accompanying sound produced by the flame. A feedback loop model for determining the likelihood of and diagnosing combustion oscillations was reviewed, enhanced, and then validated. The current work applies the feedback loop stability model to two boilers, which …

Cerium Oxide (Ceo2) Promoted Oxygen Carrier Development And Scale Modeling Study For Chemical Looping Combustion, Fang Liu

Theses and Dissertations--Mechanical and Aerospace Engineering

According to IPCC reports, the greenhouse gas CO₂ is responsible for global climate change. Studies show that CO₂ concentration reached a level of 400 ppm in 2013, or 40 % above pre-industrial levels. The contribution of CO₂ from industrial activity to increasing global CO₂ concentrations is widely accepted and points to the need to reduce the emission of this greenhouse gas.One possible combustion technology that shows promise for reducing CO₂ emissions is chemical looping combustion (CLC). It is an oxy-fuel technology, but has the advantages of in situ oxygen separation, low NO_x emissions and …

Distribution Map Of Multi-Walled Carbon Nanotubes In A Refrigerant/Oil Mixture Within A 2.5 Ton Unitary Air-Conditioner, Warren Russell Long

Graduate Theses and Dissertations

In recent years, nanoparticles have received considerable attention as a potential additive to heat transfer fluids (i.e. refrigerant) in order to increase the heat transfer capabilities of these fluids. The potential of carbon nanotubes (CNTs) to exit the compressor, migrate throughout a vapor compression air conditioning system, and possibly foul the components of such a system was experimentally investigated in this research. Six grams of CNTs were dispersed in the polyol ester oil used by a 2.5 ton (8.79 kW) unitary air conditioning system, which was continuously operated for 168 hours. After this time, the unit was shut down and …

Design And Simulation Of Passive Thermal Management System For Lithium-Ion Battery Packs On An Unmanned Ground Vehicle, Kevin Kenneth Parsons

Master's Theses

The transient thermal response of a 15-cell, 48 volt, lithium-ion battery pack for an unmanned ground vehicle was simulated with ANSYS Fluent. Heat generation rates and specific heat capacity of a single cell were experimentally measured and used as input to the thermal model. A heat generation load was applied to each battery and natural convection film boundary conditions were applied to the exterior of the enclosure. The buoyancy-driven natural convection inside the enclosure was modeled along with the radiation heat transfer between internal components. The maximum temperature of the batteries reached 65.6 °C after 630 seconds of usage …

Investigation Of Shroud Geometry To Passively Improve Heat Transfer In A Solar Thermal Storage Tank, Matthew Keene Zemler

Doctoral Dissertations and Master's Theses

A shroud and baffle configuration is used to passively increase heat transfer in a thermal store. The shroud and baffle are used to create a vena contracta near the surface of the heat exchanger, which will speed up the flow locally and thereby increasing heat transfer. The goal of this study is to investigate the geometry of the shroud in optimizing heat transfer by locally increasing the velocity near the surface of the heat exchanger. Two-dimensional transient simulations are conducted. The immersed heat exchanger is modeled as an isothermal cylinder, which is situated at the top of a solar thermal …

The Design And Testing Of A Solar Autoclave With Broad Spectrum Sterilization Capabilities, Sarah S. Trabia

Honors College Theses

Energy is difficult to come by in developing countries and this interferes with the ability of doctors to provide good healthcare to their patients. Without decent sterilization, patients can become infected and diseases can spread throughout hospitals. This study involves designing a solar autoclave for developing countries that is as efficient as electrical autoclaves. The design is intended to not require any electrical input and to be affordable to those who cannot afford advanced medical equipment. Once the solar autoclave is designed, it will be tested to determine if it can sterilize equipment against a variety of different bacteria, including …

Silicon Wafer Temperature Distribution, Daniel Gonzalez, Nathan Jones, Dylan Justice

Mechanical Engineering

Applied Materials is a global company that designs equipment for use in the semiconductor manufacturing industry. The scope of this project covers process chambers used for depositing thin chemical films onto silicon wafers. These processes must take place in particularly specific environments– including extremely low pressures and high temperatures. One challenge engineers face when designing these processes is carefully controlling the thermal behavior of silicon wafers. Typically, behavior is predicted using time consuming and computationally expensive CFD simulations. We have been asked to address this issue with a simpler, faster model which will allow engineers to reduce the total number …

Hepa Filter Evaluation Furnace Control Unit, Matt Gainer, Marc Goupil, Andrew Woolrich

Mechanical Engineering

No abstract provided.

Computational Scheme Guided Design Of A Hybrid Mild Gasifier, You Lu

LSU New Orleans Theses and Dissertations

A mild gasification method has been developed to provide an innovative clean coal technology. The objectives of this study are to (a) incorporate a fixed rate devolatilization model into the existing 2D multiphase reaction model, (b) expand the 2D model to 3D and (c) utilize the improved model to investigate the mild-gasification process and guide modification of the mild-gasifier design. The Eulerain-Eulerian method is employed to calculate both the primary phase (air) and secondary phase (coal particles). The improved 3D simulation model, incorporated with a devolatilization model, has been successfully developed and employed to determine the appropriate draft tube dimensions, …

Phase-Resolved Characterization Of Conical Turbulent Premixed Flames: An Investigation Of Forced Blowoff Dynamics, Sayan Biswas

Master's Theses

Flame dynamics of a bluff body stabilized turbulent premixed flame as it approaches lean blowoff is of interest for practical applications. It is also important to understand the flame behavior under harmonic flow perturbations as it may occur due to acoustically unstable operation of compact combustors. In this study, a harmonically excited conical flame was studied to determine its behavior under strong burning and near blowoff conditions. Chemiluminescence imaging was employed using a Photron high speed camera to characterize the phase resolved flame characteristics for a range of excitation frequencies from 50 to 400 Hz in confined and unconfined geometries. …

Thermal Vacuum Integration For Cal Poly's Space Environments Laboratory, Chelsea Barackman, Steven Jackowski

Aerospace Engineering

The purpose of the senior project is to construct a thermal vacuum by utilizing a preexisting vacuum chamber in the Space Environments Lab, and a donated Advanced Thermal Sciences (ATS) chiller. While a thermal vacuum is already available on campus, building one for the Space Environments Lab would grant undergraduates access to the equipment, allowing a much better understanding of testing methods and procedures in use by the aerospace industry. This paper explains the design and analysis of the thermal vacuum (T-VAC) project as well as the operation and procedures required for the ATS chiller and fill/drain tank. The thermal …

California Olive Ranch Hedger, Tyler Enos, Seth Abbott, David Gamba

Mechanical Engineering

The purpose of this project is to evaluate the problems of the current KCI (Kingsburg Cultivator Incorporated) olive tree hedger in use at California Olive Ranch (COR) in Artois, CA, and then correct these problems which should yield a better performing, more efficient, and reliable machine. These problems include: the hydraulic oil temperature getting too high, the saw blades not having enough horsepower, and poor cutting performance due to operator error as well as terrain variations.

Cryogenic Heat Switch, Daniel Brodkey, Esteban Ruiz, Cristal Vasquez

Mechanical Engineering

A prototype cryogenic heat switch capable of transferring heat at cryogenic temperatures, while decoupling to prevent irreversible heat damage and minimizing parasitic heat loads, is to be developed for the Jet Propulsion Laboratory. Various material properties and cryogenic heat transfer processes will be investigated to determine the best solution for this project. A working proof of concept model will be constructed that may eventually be integrated onto a spacecraft’s passive cooler systems to protect them from the irradiation emitted by the sun, from the albedo of planets, and other malicious heat sources.

Frg Turbojet, Tyler Vitti

Computer Engineering

Members of the Cal Poly SLO campus club FRG work together with students of several different disciplines to build a functional turbojet engine. Engineering approaches include design, fabrication, testing, and computer sensing, control, and integration. The goal of the project is to produce a running turbojet engine monitored and controlled by embedded hardware and specialized PC software. This project is to be used by later groups for further research and development.

An Investigation Of Mist/Air Film Cooling With Application To Gas Turbine Airfoils, Lei Zhao

LSU New Orleans Theses and Dissertations

Film cooling is a cooling technique widely used in high-performance gas turbines

to protect turbine airfoils from being damaged by hot flue gases. Film injection holes are

placed in the body of the airfoil to allow coolant to pass from the internal cavity to the

external surface. The ejection of coolant gas results in a layer or “film” of coolant gas

flowing along the external surface of the airfoil.

In this study, a new cooling scheme, mist/air film cooling is proposed and

investigated through experiments. Small amount of tiny water droplets with an average

diameter about 7 μm (mist) is …

Analysis And Testing Of Heat Transfer Through Honeycomb Panels, Daniel D. Nguyen

Aerospace Engineering

This project attempts to simulate accurately the thermal conductivity of honeycomb panels in the normal direction. Due to the large empty space of the honeycomb core, the thermal radiation mode of heat transfer was modeled along with conduction. Using Newton’s Method to solve for a steady state model of heat moving through the honeycomb panel, the theoretical effective thermal conduction of the honeycomb panel was found, ranging from 1.03 to 1.07 Q/m/K for a heat input of 2.5 W to 11.8 W. An experimental model was designed to test the theoretical results, using a cold plate and a heat plate …

Perceptions Measurement Of Professional Certifications To Augment Buffalo State College Baccalaureate Technology Programs, As A Representative American Postsecondary Educational Institution, Christopher N. Brown

Industrial Technology Theses

The purpose of this study was to assess, measure, and analyze whether voluntary, nationally-recognized professional certification credentials were important to augment technology programs at Buffalo State College (BSC), as a representative postsecondary baccalaureate degree-granting institution offering technology curricula. Six BSC undergraduate technology programs were evaluated within the scope of this study: 1.) Computer Information Systems; 2.) Electrical Engineering, Electronics; 3.) Electrical Engineering, Smart Grid; 4.) Industrial Technology; 5.) Mechanical Engineering; and 6.) Technology Education. This study considered the following three aspects of the problem: a.) postsecondary technology program enrollment and graduation trends; b.) the value/awareness of professional certifications to employers …