Heat Transfer, Combustion Commons^™

Characterization Of Nano-Porous Si-Cu Composites To Enhance Lubricant Retention Impacting The Tribological Properties Of Sliding Surfaces, Julius Sheldon Morehead

Graduate Theses and Dissertations

As the expectations for modern machinery's tribological and thermal performances continue to rise, the retention of lubricant on the contact surfaces of their sliding components becomes an increasingly important issue. Friction and wear cause heat-related failures which lead to catastrophic damage to machinery. Evaporation of a lubricant's volatile constituents as well as lubricant migration leads not only to a reduction in lubricant quantity but also in its quality, thus facilitating component failures. In order to enhance component reliability, the surface should incorporate features that actively retain lubricants. The unique properties of nano-porous topographies such as their high surface area-to-volume ratio …

Benchmarking, Characterization And Tuning Of Shell Ecomarathon Prototype Powertrain, Eric J. Griess

Master's Theses

With the automotive industry ever striving to push the limits of fuel efficiency, the Shell EcoMarathon offers a glimpse into this energy conserving mindset by challenging engineering students around the world to design and build ultra-efficient vehicles to compete regionally. This requires synchronization of engineering fields to ensure that the vehicle and powertrain system work in parallel to achieve similar goals.

The goal for Cal Poly – San Luis Obispo’s EcoMarathon vehicle for the 2015 competition is to analyze the unique operating mode that the powertrain undergoes during competition and improve their current package to increase fuel efficiency. In this …

Development Of An Autonomous Single-Point Calibration For A Constant Voltage Hot-Wire Anemometer, Ryan Murphy

Master's Theses

Traditionally, the measurement of turbulence has been conducted using hot-wire anemometry. This thesis presents the implementation of a constant voltage hot-wire anemometer for use with the Boundary Layer Data System (BLDS). A hot-wire calibration apparatus has been developed that is capable of operation inside a vacuum chamber and flow speeds up to 50 m/s. Hot-wires operated with a constant-voltage anemometer (CVA) were calibrated at absolute static pressures down to 26 kPa. A thermal/electrical model for a hot-wire and the CVA circuit successfully predicted the measured CVA output voltage trend at reduced pressure environments; however, better results were obtained when the …

Development Of Local Transient Heat Flux Measurements In An Axisymmetric Hybrid Rocket Nozzle, Christopher D'Elia

Master's Theses

A method of performing local transient heat flux measurements in an uncooled axisymmetric hybrid rocket nozzle is presented. Surface temperatures are collected at various axial locations during short duration tests and post processed using finite difference techniques to determine local transient heat fluxes and film coefficients. Comparisons are made between the collected data and the complete Bartz model. Although strong agreement is observed in certain sections of the nozzle, ideal steady state conditions are not observed to entirely validate the Bartz model for hybrid rocket nozzles. An experimental error analysis indicates the experimental heat fluxes are accurate within ±5.2% and …

Suborbital Spaceflight: A Student Team’S Plan To Send A Rocket To Space, Bryce Chanes, William Carpenter, Julio Benavides, Matthew Haslam, Brenda Haven

Aviation / Aeronautics / Aerospace International Research Conference

The Eagle Space Flight Team was created with the goal of becoming the first undergraduate team to design, build, and launch a rocket capable of suborbital spaceflight. In order to achieve this goal, the team will have to design a rocket capable of atmospheric flight at speeds over Mach 5 and launch it on one of the largest amateur rocket motors ever made. Over the next three years, the team will progress towards accomplishing this feat through a series of incremental test flights. Before the space flight, the team will build three sub-scale rockets designed to reach altitudes of 30,000’, …

Coalescence-Induced Jumping Of Droplet: Inertia And Viscosity Effects, Samaneh Farokhirad, Jeffrey F. Morris, Taehun Lee

Publications and Research

The problem of coalescence-induced self-propelled jumping of droplet is studied using three-dimensional numerical simulation. The focus is on the effect of inertia and in particular the effect of air density on the behavior of the merged droplet during jumping. A lattice Boltzmann method is used for two identical, static micro-droplets coalescing on a homogeneous substrate with contact angle ranging from 0◦ to 180◦. The results reveal that the effect of air density is significant on detachment of the merged droplet from the substrate at the later stage of the jumping process; the larger the air density, the larger the jumping …

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Faculty Publications

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

Designing A Heat Sink For Lithium-Ion Battery Packs In Electric Vehicles, Evan Foreman, Dylan Irvine, Aaron Jackson, Christopher Brandon Remington, Sam Endrizzi

Williams Honors College, Honors Research Projects

This report addresses the concepts and implementation of fluid cooled heat sink designs for an electric or hybrid vehicle battery. To determine the battery’s temperature and heat flux profile, testing was performed by measuring these values at multiple locations on a lithium-ion pouch battery using heat flux sensors and thermocouples during the charge and discharge cycles of the battery. Once the data was collected and analyzed, trendlines were fit to the heat flux data then used to create equations for the heat flux profile during the discharging stage. Each equation represented a specific region on the battery geometry. Four heat …

Incorporating Dynamic Flame Behavior Into The Scaling Laws Of Wildland Fire Spread, Brittany A. Adam

Theses and Dissertations--Mechanical and Aerospace Engineering

A challenge for fire researchers is obtaining data from those fires that are most dangerous and costly. While it is feasible to instrument test beds, test plots, and small prescribed burns for research, it is uncommon to successfully instrument an active wildland fire. With a focus on very specific facets of wildland fire, researchers have created many unique models utilizing matchsticks, cardboard, liquid fuel, excelsior, plywood, live fuels, dead fuels, and wood cribs of different packing densities. Such scale models, however, only serve as valid substitutes for the full-scale system when all functional relations of the scale model are made …

Effect Of Heating And Ionization Of Four Atomizing Gases On The Spray Characteristics Of A High Volume Low Pressure Spray Atomizer, Anthony V. Adornato

Theses and Dissertations--Mechanical and Aerospace Engineering

The disintegration of a liquid jet emerging from a nozzle by a high speed gas stream has been under investigation of several decades. A result of the liquid jet disintegration is droplet formation. This process is referred to as atomization. Industrial applications use atomization as a method for applying coatings to substrates. It has been reported that the use of other atomizing gases instead of compressed plant air will positively affect paint droplet size distributions, spray patterns and finish qualities; furthermore, the ionization and heating of the atomizing gas was reported to positively affect finish qualities. Although ionization techniques have …

An Experimental Method Of Measuring Spectral, Directional Emissivity Of Various Materials And Joule Heating, Robert Bickel

Theses and Dissertations--Mechanical and Aerospace Engineering

Emissivity is an important parameter in calculating radiative cooling of a surface. In experiments at the NASA Ames hypervelocity ballistic range, one of the main errors indicated in temperature measurements is the uncertainty of emissivity for the materials under investigation. This thesis offers a method for measuring emissivity of materials at elevated temperatures at the University of Kentucky. A test specimen which consists of different sample materials under investigation and a blackbody cavity was heated in a furnace to an isothermal condition at known temperature. The emitted thermal radiation was measured and the comparison of sample and blackbody radiation yielded …

Modeling Of Spallation Phenomenon In An Arc-Jet Environment, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles, while entering the planetary atmosphere, experience high loads of heat. Ablative materials are commonly used for a thermal protection system, which undergo mass removal mechanisms to counter the heat rates. Spallation is one of the ablative processes, which is characterized by the ejection of solid particles from the material into the flow. Numerical codes that are used in designing the heat shields ignore this phenomenon. Hence, to evaluate the effectiveness of spallation phenomenon, a numerical model is developed to compute the dynamics and chemistry of the particles. The code is one-way coupled to a CFD code that models …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

Radiative Conductivity Analysis Of Low-Density Fibrous Materials, Nima Nouri

Theses and Dissertations--Mechanical and Aerospace Engineering

The effective radiative conductivity of fibrous material is an important part of the evaluation of the thermal performance of fibrous insulators. To better evaluate this material property, a three-dimensional direct simulation model which calculates the effective radiative conductivity of fibrous material is proposed. Two different geometries are used in this analysis.

The simplified model assumes that the fibers are in a cylindrical shape and does not require identically-sized fibers or a symmetric configuration. Using a geometry with properties resembling those of a fibrous insulator, a numerical calculation of the geometric configuration factor is carried out. The results show the dependency …

Low-Order Discrete Dynamical System For H2-Air Finite-Rate Combustion Process, Wenwei Zeng

Theses and Dissertations--Mechanical and Aerospace Engineering

A low-order discrete dynamical system (DDS) for finite-rate chemistry of H₂-air combustion is derived in 3D. Fourier series with a single wavevector are employed to represent dependent variables of subgrid-scale (SGS) behaviors for applications to large-eddy simulation (LES). A Galerkin approximation is applied to the governing equations for comprising the DDS. Regime maps are employed to aid qualitative determination of useful values for bifurcation parameters of the DDS. Both isotropic and anisotropic assumptions are employed when constructing regime maps and studying bifurcation parameters sequences. For H₂-air reactions, two reduced chemical mechanisms are studied via the DDS. …

Transient Thermoelectric Supercooling: Isosceles Current Pulses From A Response Surface Perspective And The Performance Effects Of Pulse Cooling A Heat Generating Mass, Alfred Piggott

Dissertations, Master's Theses and Master's Reports

With increased public interest in protecting the environment, scientists and engineers aim to improve energy conversion efficiency. Thermoelectrics offer many advantages as thermal management technology. When compared to vapor compression refrigeration, above approximately 200 to 600 watts, cost in dollars per watt as well as COP are not advantageous for thermoelectrics. The goal of this work was to determine if optimized pulse supercooling operation could improve cooling capacity or efficiency of a thermoelectric device. The basis of this research is a thermal-electrical analogy based modeling study using SPICE. Two models were developed. The first model, a standalone thermocouple with no …

Elementary Assessments And Simulations Based Proposals For New Heat Transfer Correlations And Flow Regime Maps For Annular/Stratified Regime Of Shear Driven Internal Condensing Flows, Siddharth Ravikumar

Dissertations, Master's Theses and Master's Reports

Contemporary cooling applications necessitate the use of mm-scale shear driven flow condenser designs which also need to ensure substantial heat transfer rates for a wide range of flow conditions. Some modern shear driven flow condensers must meet the requirements of small size and large heat flux removal capability for variety of flow conditions. For this, effective estimates of heat transfer rate correlations and correlations for estimating the length of the annular regime are essential. Existing heat transfer correlations are built based on semi-empirical approaches which are primarily supported by large data sets, which are often mixed with insufficient explanation and …

Prosthetic Thermal Management Device, Garrett Dowd

Williams Honors College, Honors Research Projects

High temperatures in lower-limb prosthetics can lead to poor user skin conditions and mechanical slippage between the user’s limb and the prosthetic. This report presents an air-cooling device for a lower-limb prosthesis. This device’s purpose is to maintain a constant skin-prosthesis interface temperature. A compact heat sink and small fan were used to transfer the bio-heat to the ambient surroundings. By changing the power of the fan, the thermal resistance of the whole system can be adjusted to match various thermal loads and environmental temperatures. Heat pads were used to mimic the heat generation of a residual limb, and cooling …

2015 Afrl University Design Challenge, Daniel Slattery, Andrew P. Killmeyer, Brandon Null, Brendan Jones, Casey Hale, Jake Stein, Jeff Quartermaine, Kevin Rolik, Nick Tsangeos, Sam Moats, Marisa Seeley

Williams Honors College, Honors Research Projects

The University of Akron’s Air Force Research Laboratory’s Design Challenge Team has engineered a Heat Stress Prevention Kit that includes a facial mask in which the soldier will cool down from the inside out by breathing in the cool air circulating throughout the mask. This cool air is produced from a thermoelectric chip, which has a specific temperature difference on either side, one hot and one cold. Each of the sides is isolated from one another and with the combination of heat sinks, fans, and the simple process of breathing, a system is created by inhaling cool air. The entire …

Design Of The University Of Akron's 2015 Fsae Electric Vehicle Braking System, Nicholas D. Galbincea

Williams Honors College, Honors Research Projects

The following report encompasses the design of the 2015 University of Akron’s FSAE formula electric braking system. The system is one based on hydraulic braking and designed for a one man performance racing vehicle. The objective of the system is to convert the kinetic energy of the vehicle into thermal energy, allowing the vehicle to decelerate optimally and safely. The design includes three major categories: calculation and evaluation of the hydraulic system in order to select calipers and master cylinders, the design of the pedal box, and the design of the rotors.

The results and findings of the proceeding report …