Heat Transfer, Combustion Commons^™

Effect Of Adding Palm Fiber To Thermal Conductivity Of Quick Set Concrete, Monica Garcia

Theses and Dissertations

As climate change becomes a more dire issue and more readily accepted by those in power, the demand for local and systemic solutions grows louder. In urban environments, one issue of concern is the contribution of anthropogenic heat from buildings which contributes to localized warming of the environment. A method that can reduce anthropogenic heat is decreasing the thermal conductivity of building materials. The objective of this study is to examine the possibility of using palm fibers to reduce the thermal conductivity of quick-set concrete samples. The data gathered in this study are used to determine the thermal conductivity value …

Molecular Mechanisms And Design Of Hydrogen-Bonded Materials For Thermal Applications, Jinlong He

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Heat transfer at the nanoscale plays an important role in determining the reliability and performance of many innovative advanced materials technologies such as nanoelectronics, semiconductor, biomedical devices, polymers, and composites. Extensive efforts have been made to design materials with extraordinary thermal properties. However, fundamental understanding of heat transfer in many of these materials is still not lacking, because the thermal transport processes are governed by several factors including molecular morphology and chemical bonding. Among these factors, the atomic bonding between two dissimilar materials or within single materials is of particular interest due to its ubiquity and importance in physical processes. …

Modeling, Simulation, And Testing Of Sweeping Convection, Amir Kiaee

Mechanical Engineering Research Theses and Dissertations

In this study, the new convection heat transfer concept of sweeping convection, using large particles flowing with a fluid in a channel, is considered. This novel concept is inspired by the gas exchange process in alveolar capillaries, where red blood cells (RBCs) flow with blood plasma, yielding very high gas transfer efficiency. An important characteristic of alveolar capillary blood flow, believed to be related to the high efficiency of the lungs, is the snug fitting of the RBCs into the capillaries. This tight fitting sets the RBCs (particles) acting like pistons as they flow downstream with the plasma (fluid), facilitating …

Thermal Control Development Of A Proton Exchange Membrane Fuel Cell System, Ola Mohammed Taha Al-Shalash

Mechanical Engineering Theses

A fuel cell is an electrochemical energy conversion device that uses fuel to generate electricity. It basically converts the chemical energy of reactants directly into electricity without combustion. In a Proton Exchange Membrane Fuel Cell (PEMFC), the reactants, hydrogen and oxygen, are fed into the two electrodes, anode and cathode, respectively. A reaction takes place at each electrode and produces electricity, as well as water, and heat as the by-products. In order to maximize performance of a fuel cell, many factors can be considered for tuning and control. Temperature management is one of these factors.

A thermal-fluid model of a …

Potential Energy Generation From Agricultural Residue In Indonesia, Adrian Rizqi Irhamna

International Programs

Indonesia has great potential of biomass sources from their agricultural residue, which can potentially be used for alternative energy generation. This preliminary research explores the most suitable technology for energy generation from agricultural residue and its challenge for application in Indonesia. The study showed that biomass utilization via the direct combustion process is recommended for energy generation. It is also reported that the pretreatment process of drying and washing, are required to increase the fuel quality and plant efficiency.

Cooking Systems Using Aluminum Foam, Ryan Tetsuo Mizukami

Physics

In developing countries, the use of wood burning fires for cooking is cause for illness and death. With this in mind, research was conducted to develop a solar cooking device capable of cooking of soup within 15 mins in order to reduce the negative impacts of cooking with wood. Current methods of solar-based cooking, such as solar concentrators and solar tube ovens, are impractical. A small solar panel is a cost-effective way to produce energy but will not produce enough power to cook within a reasonable amount of time. Even if it is assumed that all of the energy produced …

Study Of Heat Transfer And Friction Loss Of Nanofluid Suspension Flow In Square Pipe Heat Exchanger, Krishnan Jayprasanth

Student Works (2020-2029)

An experimentational analysis was done to evaluate heat transfer features of graphene oxide (GO) nanofluid inside the cross section of square cross tube that was exposed to a uniform constant heat flux of the test segments. Lately huge figures of researches have been are proceeded out to examine the outcome of nanofluid in augmentation of the heat transfer rate in numerous heat exchangers particularly using hummer method to attain GO. In this case, advanced hummer method was used to obtain GO and further analyses the effect of the nanofluids. The viscosity and thermal conductivity for the (GO) nanofluids at the …

Cfd Modelling Of Multiphase Flow In Static Mixer, Silverrajan Viknesvaran

Student Works (2020-2029)

Modelling of Multiphase flow through a Kenics static mixer were presented in this paper. Multiphase mixing is a challenging process in industries such as pharmaceutical, food and petroleum since two-different phases can be immiscible towards each other. Stirred tank mixing is the most common method used in industries. However, this type of method costs a lot in terms of energy and manpower specially when mixing immiscible liquids. Hence, The Kenics Static Mixer could be a good solution for multiphase mixing when its correctly configured and studied. Two phases used in this paper were aqueous solution: refined CMC as continuous phase …

Investigations Of Air-Water Multiphase Flow In Tubes: Computational Fluid Dynamics, Wei Hong Goo

Student Works (2020-2029)

Mixing is a very crucial process in many industries, such as food processing industry, minerals processing industry, petrochemicals and refining industry, pulp and paper industry, polymer industry, pharmaceuticals industry and many more. There are different types of mixing, such as liquid-gas mixing, liquid-liquid mixing, solid-liquid mixing and many more. The definition of multiphase flow is the simultaneous flow of materials with multiple thermodynamic phases. A lot of process industries require multiphase flows during operation. Bubbly flow is defined as the flow of liquids that contains dispersed gas bubbles. One of the main applications of multiphases flows and bubbly flows is …

Kinetic Study Of In-Pipe Water Flow For Power Generation, Surendaran Venuthan

Student Works (2020-2029)

In-pipe turbine generator has a potential to harvest energy from an existing water flow from distribution pipe which have natural and pumping capacity. That flow will be used to convert kinetic energy from the pipe to rotate the turbine. In turn, the turbine may be connected to a generator to produce electric power. The fact that the in-pipe turbine generator will be a useful energy harvesting tool with potential with industrial application is recommended by many scholars. However, there is a concern where there are many types and sizes of pipe that is readily used in the water works industry. …

Study Of Heat Transfer And Friction Loss Of Nanofluid Suspension Flow In Circular Pipe Heat Exchanger, Ramadas Sandru

Student Works (2020-2029)

This stated experiment focused on the study of convective heat transfer and friction loss in a circular flow passage for Graphene oxide-based nanofluids which are consist of Graphene Oxide/Distilled water with their different wt. % concentrations. These GO/DW based nanofluids where been prepared by using a facile two-step method, while the GO particles were synthesized by a modified hummer method. Four different (0.025, 0.05, 0.075, and 0.1 wt. %) were produced by dispersing graphene particles in distilled water under high probe sonication. The GO/DW based nanofluids flowing in a horizontal shell and tube heat exchanger counter flow under turbulent flow …

What Difference Does A Catalyst Make?, Tammy Guthrie, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use different catalysts for the decomposition of Hydrogen Peroxide, to determine if different catalysts affect the energy that is generated during the reaction.

A Computational Study Of Water Mobility On Smooth Surface, Cavities And Porous Structure With Hydrophilic And Hydrophobic Coatings, Kok Wee Yong

Student Works (2020-2029)

This research focus on water mobility and discovers a new phenomenon where droplet accelerates on a hydrophilic cavity surface when sliding down from a hydrophobic surface. The kinetic energy of droplet increases six (6) times higher than before sliding into the first cavity. This finding is useful for creating an effective way of filling liquids into cavities for passive microfluidics related devices. The work consists of validating cases using Computational Fluid Dynamics (CFD) software. The first part of the research reviews the literature regarding CFD modelling of a water droplet (i) sliding down on a surface, (ii) detachment in a …

Development Of Reduced Chemical Kinetic Models For The Numerical Simulation Of Combustion And Emissions Behavior Of Representative Conventional And Bio-Derived Fuels, Mazen A. Eldeeb

Mineta Transportation Institute

The study addresses two of the main challenges facing combustion modeling for transportation fuels: simultaneous simulation of non-related combustion problems and reducing the computational cost of the modeling process itself. To address the first challenge, researchers determine a characteristic flame time from thermal diffusivity and laminar burning velocity. Researchers examine parametric dependence of flame time and ignition delay time on pressure, temperature and equivalence ratio for methane, based on validated chemical kinetic mechanisms. The study reveals flame time and ignition delay time show similar temperature dependence, flame time has stronger dependence on equivalence ratio and weaker dependence on pressure than …

The Effect Of Orientation On The Ignition Of Solids, David Morrisset

Master's Theses

The ignition of a solid is an inherently complex phenomenon influenced by heat and mass transport mechanisms that are, even to this day, not understood in entirety. In order to use ignition data in meaningful engineering application, significant simplifications have been made to the theory of ignition. The most common way to classify ignition is the use of material specific parameters such as such as ignition temperature (T_ig) and the critical heat flux for ignition (CHF). These parameters are determined through standardized testing of solid materials – however, the results of these tests are generally used in applications …

Raysun's Infrared Raisin Dryer, Lucas Kensinger, Saraith Aispuro, Joe Vanacore

General Engineering

The RaySuns senior project team was tasked with lowering the drying costs of raisins for River Ranch Raisins. In doing so, we explored several options for cutting costs: utilizing automation and exploring new drying technologies were our primary focus. We eventually planned a modular infrared heating mechanism which would be easy to automate in future projects. After manufacturing and testing an infrared heating mechanism, it was found that infrared drying could significantly cut costs versus the previous natural gas fired dryer tunnels while leaving room for automation. The infrared dryer was also shown to have the potential to create high-quality …

Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom

Mechanical Engineering

This document outlines the critical design details and timeline for the Design for Additive Manufacturing Senior Project sponsored by Solar Turbines, Inc. The scope of this project encompasses the redesign of two of Solar Turbine’s cast parts for metal additive manufacturing in order to minimize lead time, cost, and weight. With the overall objective of performing in-depth analysis exploring affordability & feasibility, this redesign process will aid Solar Turbines in expanding their knowledge of Design for Additive Manufacturing principles and enable them to further incorporate the use of additive manufacturing into their production processes. The first part that the team …

Analysis Of Burning Wood In The Transient State And The Application To Structural Design, Roberta Veliz, Kimberly Guzman

Architectural Engineering

Determining the extent of the contribution of exposed timber on compartment fire dynamics in open floor plans is a complex process. Designers traditionally used compartmentalization design methods which create spaces where flashover is likely, given the fuel load and ventilation conditions. However, due to the large geometric dimensions and spread of fuel, fires in open floor plans are more likely to remain as localized or traveling fires. As such, an understanding of not only ignition potential but also flame spread is critical to characterizing the contribution of exposed timber. An integral step in characterizing the potential contribution is through an …

Study Of Heat And Momentum Transfer To Colloidal Suspensions In Annular Closed Conduit Flow, Sadik Shoaib

Student Works (2020-2029)

With the advancement of science and the rapid growth of industries and the improved lifestyles of people, energy consumption has been increasing. Whereas the exploration of energy remained at a slower pace and the energy reservoirs are extinguishing at a faster rate. High energy consumption is also encouraging environmental pollution and global warming. Considering all these issues, scientists and engineers are desperately exploring highly efficient heat exchangers for the conservation of energy and minimize its losses. The present research has focused on obtaining highly efficient heat exchangers. Lots of research have performed on the improvement of heat exchanger materials, alteration …

Synthesis Of Eco-Friendly Nanofluids For Enhancement Of Heat Transfer And Application In Different Flow Configuration Passages, Khan Asif

Student Works (2020-2029)

Since the invention of the heat exchangers, the working fluids such as water, ethyl glycol, oil and many others were used, however, they reveal relatively low thermal conductivity. Eco-friendly nanofluids and the cost-effective annular heat exchangers were introduced in this research to overcome the problem. In the present work, heat transfer coefficient and friction loss analyses of (TiO2 and GNP) water-based nanofluids were compared with DI-water flowing in annular conduit under turbulent flow regime. The nanoparticle weight concentrations of 0.1, 0.075, 0.05 and 0.025 wt.% were prepared by using a simple two-step method. The DI-water simulations were conducted by using …