Acoustics, Dynamics, and Controls Commons^™

Performance Of Hard Disk Drives In High Noise Environments, Trinoy Dutta

Dissertations, Master's Theses and Master's Reports

Digital information stored in rotational media, such as Hard Disk Drives (HDD) needs to be reliable and readily accessible. Various studies have been performed on the modal analysis of HDDs and the noise emitted during operation. Analysis performed by Siemens Corporation, IBM and Tyco Fire Protection Products show that HDDs are sensitive to noise. This report initially focusses on identifying the critical frequency ranges and the levels of noise where the performance of the drives reduces. A series of tests have been performed using pink noise at one-third octave frequency bands at sound pressure levels ranging from 80 dB to …

Multi-Modal And Short-Range Transmission Loss In Ice-Covered, Near-Shore Arctic Waters, Miles B. Penhale

Dissertations, Master's Theses and Master's Reports

In the past century, extensive research has been done regarding the sound propagation in arctic ice sheets. The majority of this research has focused on low frequency propagation over long distances. One of the most commonly used excitation methods for air-ice-water layers has been explosives. However, environmental regulation has become more stringent, disallowing the use of almost all explosive excitation types. Due to changing climate conditions in these environments, new experimentation is warranted to determine sound propagation characteristics in, through, and under thin ice sheets, in shallow water, over short distances. In April, 2016 several experiments were conducted approximately 2 …

Simulation Of Human Ankle Trajectory During Stance Phase Of Gait, Leslie Castelino

Dissertations, Master's Theses and Master's Reports

A simulation was developed which mimics the human gait characteristics based on the input of an individual’s gait trajectory. This simulation also estimates the impedance of the human ankle based on the ground reaction forces measured by the force plate. This simulation will accept alterations of the following parameters: total body weight, weight of the shank, weight of the foot, trajectories of the shank and foot of the individual and orientation of the force plate, which would generate a new gait trajectory for the ankle during the stance phase of gait. The goal of this simulation was to validate the …

Active Management Assistant System For Embry-Riddle Ecocar 3 Hybrid Supervisory Control System, Matthew Nelson, Blair Cutting, Michael J. Aleardi

Student Works

The Embry-Riddle EcoCAR 3 team is developing a prototype hybrid Chevrolet Camaro utilizing a customized vehicle powertrain controller. This controller is serving to ensure system safety, vehicle operation, and consumer drivability while also incorporating advanced driving aids to achieve both the desired performance levels one expects from a Camaro as well as vehicle efficiency. This vehicle must reach the team set vehicle technical specifications of a 4.9 second 0 to 60 time while maintaining a 53 miles per gallon gasoline equivalence rating.

In order to reach the efficiency goal, the team is developing an Active Management Assistance System utilizing computer …

Implementation And Performance Evaluation Of Acoustic Denoising Algorithms For Uav, Ahmed Sony Kamal Chowdhury

UNLV Theses, Dissertations, Professional Papers, and Capstones

Unmanned Aerial Vehicles (UAVs) have become popular alternative for wildlife monitoring and border surveillance applications. Elimination of the UAV’s background noise and classifying the target audio signal effectively are still a major challenge. The main goal of this thesis is to remove UAV’s background noise by means of acoustic denoising techniques. Existing denoising algorithms, such as Adaptive Least Mean Square (LMS), Wavelet Denoising, Time-Frequency Block Thresholding, and Wiener Filter, were implemented and their performance evaluated. The denoising algorithms were evaluated for average Signal to Noise Ratio (SNR), Segmental SNR (SSNR), Log Likelihood Ratio (LLR), and Log Spectral Distance (LSD) metrics. …

Optimal Design Of Sound Absorbing Systems With Microperforated Panels, Nicholas Nakjoo Kim

Open Access Dissertations

As the development of technology makes economic prosperity and life more convenient, people now desire a higher quality of life. This quality of life is based not only on the convenience in their life but also on clean and eco-friendly environments. To meet that requirement, much research is being performed in many areas of eco-friendly technology, such as renewable energy, biodegradable content, and batteries for electronic vehicles.

This tendency is also obvious in the acoustics area, where there are continuing attempts to replace fiber-glass sound absorbers with fiber-free materials. The combination of microperfoated panels (MPP) (one of the fiber-free sound …

Energy Localization And Heat Generation In Composite Energetic Systems Under High-Frequency Mechanical Excitation, Jesus O. Mares

Open Access Dissertations

In this work, the ability to use high frequency mechanical excitation to generate significant heating within plastic bonded explosives, as well as single energetic particles embedded within a viscoelastic binder, is studied. In this work, the fundamental mechanisms associated with the conversion of high-frequency mechanical excitation to heat as applied to these composite energetic systems are thoroughly investigated.

High-frequency contact excitation has been used to generate a significant amount of heat within samples of PBX 9501 and representative inert mock materials. Surface temperature rises on the order of 10 °C were observed at certain frequencies over a range from 50 …

Design Of A Flexible Control Platform And Miniature In Vivo Robots For Laparo-Endoscopic Single-Site Surgeries, Lou P. Cubrich

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Minimally-invasive laparoscopic procedures have proven efficacy for a wide range of surgical procedures as well as benefits such as reducing scarring, infection, recovery time, and post-operative pain. While the procedures have many advantages, there are significant shortcomings such as limited instrument motion and reduced dexterity. In recent years, robotic surgical technology has overcome some of these limitations and has become an effective tool for many types of surgeries. These robotic platforms typically have an increased workspace, greater dexterity, improved ergonomics, and finer control than traditional laparoscopic methods. This thesis presents the designs of both a four degree-of-freedom (DOF) and 5-DOF …

Dynamic Responses Of Wheel-Rail Systems With Block Dampers, Tzuyu Tseng

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The wheel-rail interaction problem has been widely studied in the past few decades. In this problem, dynamic responses at the contact areas remain the central issue since they induce damage to the rail over time. In particular, the dynamic responses at the contact areas between the wheels and rails present difficulties in understanding and mathematical modeling. Even with the computer power one has today, its mathematical modeling employs the versatile numerical analysis method, the finite element method (FEM) remains a formidable challenge due to its extremely small contact areas and in turn the extremely high stress levels. In addition, friction …

3-Axis Automated Probe Traverse For Aerodynamic Testing, Tananant Boonya-Ananta, Ricky Wai, Zander Oostman, Teyvon Brooks

Mechanical Engineering

Our primary objective is to design, build, and test an automated traverse to hold measurement probes in Cal Poly’s low speed wind tunnel. The device should cause minimal flow disturbance. It’s movements must be able to cover eighty percent of the three-dimensional test section. The device should have a mounting point for interchangeable probes. The assembly is to be integrated with the current frame structure on the wind tunnel test section, and should allow very minimal deflection of the measurement probe. The user should be able to control the motion of the traverse via a computer interface which supports automatic …

Extracting Vibration Characteristics Of A Guitar Using Finite Element, Modal Analysis, And Digital Image Correlation Techniques, Kiran Patil, Javad Baqersad, Daniel Ludwigsen, Yaomin Dong

Physics Publications

The sound quality generated by the guitar depends on the vibration characteristics (i.e. natural frequencies and mode shapes) of this instrument. Thus, it is of particular interest to the guitar manufacturers to be able to obtain global information about the characteristics of the guitar. Traditional sensors can only measure at discrete locations. However, digital image correlation (DIC) can measure full-field data on the surface of the structure. In the current paper, a finite element (FE) model of a guitar with free boundary configurations was developed using quadratic solid elements. An eigensolution was performed on the FE model to determine its …

A Bioinspired Modification For Uas Propeller/Rotor Noise Reduction, Mark N. Callender

ASA Multidisciplinary Research Symposium

This projects presents a bioinspired modification to UAS propellers/rotors for noise reduction. Sound pressure levels (SPL) and thrust for modified propellers were compared to a baseline propeller. The bioinspired modification yielded lower SPL with a requisite increase in rpm in order to maintain a chosen level of thrust.

The Simulation For Ultrasonic Testing Based On Frequency-Phase Coded Excitation, Jiaying Zhang, Wenlong Tian, Tie Gang, Sen Cong, Zhaoyang Sheng

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Frequency Based Noise Coherence-Function Extension And Application To Passive Bottom-Loss Estimation, Lanfranco Muzi, Martin Siderius, Peter L. Nielsen

Electrical and Computer Engineering Faculty Publications and Presentations

Accurate modeling of acoustic propagation in the ocean waveguide is important to SONAR-performance prediction. Particularly in shallow waters, a crucial contribution to the total transmission loss is the bottom refection loss, which can be estimated passively by beamforming the natural surface-noise acoustic field recorded by a vertical line array of hydrophones. However, the performance in this task of arrays below 2 m of length is problematic for frequencies below 10 kHz" role="presentation" style="display: inline; line-height: normal; word-spacing: normal; word-wrap: normal; white-space: nowrap; float: none; direction: ltr; max-width: none; max-height: none; min-width: 0px; min-height: 0px; border: 0px; padding: 0px 2px 0px …

Sound Data Collection And Transmission Noise Reduction, Bradley Cockrel

Mahurin Honors College Capstone Experience/Thesis Projects

The WKU Engineering Department Senior Student Team, The Synchronizers, has been contracted to modify a MTD transmission’s sound characteristics. This project entails developing a sound data acquisition apparatus and method, developing a sound test stand which will fully load the transmission and load characteristics, and suggesting modes of sound modification. The Sound Data Acquisition method entails using a specialized microphone calibrated to operate on IOS devices to measure Sound Intensity. The sound intensity will be found over a collective area, in order to evaluate to the sound power generated. The sound test stand will consist of a system designed to …

The Effect Of Honeycomb Cavity: Acoustic Performance Of A Double-Leaf Micro Perforated Panel, Yuxian Huang, Kai Ming Li

The Summer Undergraduate Research Fellowship (SURF) Symposium

A micro perforated panel (MPP) is a device consisting of a thin plate and submillimeter perforations for reducing low frequency noise. MPPs have many advantages compared to traditional sound absorption materials, such as durability and designability, and they can be used in a variety of places such as room interior designs, passenger and crew compartments of aircrafts and combustion engines. The models in this study were designed and fabricated with the latest 3-D printing technology. The transmission loss and sound absorption coefficient of the 3-D printed double-leaf MPPs with honeycomb cavities were studied. According to the established theory, MPPs work …

Dynamic Behavior Of A Clamped-Clamped Bi-Stable Laminate For Energy Harvesting, Ajay V. Kumar, Andres F. Arrieta Ph.D., Myungwon Hwang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Multi-stable laminates have many applications in morphing structures, energy harvesting devices, and metamaterials due to the specific characteristics attributed to the exhibited stable states. Changes between stable states allow for large deflections, on-demand variation of the stiffness of compliant structures embedded within these elements, and control of effective dynamic properties in periodic lattices. These changes in state can be accessed via a snap-through instability triggered by introducing a well-defined activation energy. The resulting oscillations could enable broadband energy harvesting via piezoelectric transduction and resistive circuits. In this paper, a clamped-clamped bi-stable laminate is studied to understand the behavior of the …

Development Of Data Analytics Tools For Acoustic Measurement Of Positive Displacement Machines, Dan Ding, Monika Ivantysynova, Paul Kalbfleisch

The Summer Undergraduate Research Fellowship (SURF) Symposium

Noise control is an important factor in evaluating the design of positive displacement machines. This research project aims to develop new tools in MATLAB, with emphasis on visual approaches, to comprehensively characterize the noise generated by positive displacement machines in spatial, temporal and frequency domains. Sound pressure level (SPL), sound intensity level (SIL) and loudness were calculated and plotted on a measurement surface surrounding the pump, which illustrates the spatial distribution of the sound field. In order to highlight the phenomenon within specific frequency bands, Butterworth filters were used to isolate desired frequencies, such that specific harmonic content or 1/3 …

The Influence Of Thermal Conditions On The Thermomechanics Of Particulate-Composite, Mock Explosive Samples Under Near-Resonant Excitation, Jaylon B. Tucker, Allison R. Range, Jeffrey F. Rhoads

The Summer Undergraduate Research Fellowship (SURF) Symposium

Vapor detection is one of the most effective ways to find hidden plastic-bonded explosives in the field today. In recent years, it has been demonstrated that providing near-resonant vibratory excitation to explosives dramatically increases their vapor pressure, allowing for easier detection. Unfortunately, there currently exists a limited understanding of the thermomechanics of energetic material. This study seeks to help fill this technical void by exploring the thermomechanics of mock plastic-bonded explosives using direct mechanical excitation with varying thermal conditions. Using two different ambient thermal boundary conditions (insulated geometric boundaries and boundaries with free convection), a 7" by 10" by 0.5" …

Efficient Modeling Of Sound Source Radiation In Free-Space And Room Environments, Yangfan Liu

Open Access Dissertations

Motivated by the need to develop efficient acoustics simulations for sources in different room environments, a modeling procedure has been proposed that consists of two steps in general: (1) the modeling of the free-space radiation of the source based on measurements in a anechoic environment, and (2) the prediction of the sound field in a room environment based on that free-space information.

To achieve a high modeling efficiency, i.e., to reduce the number of modeling parameters while still maintaining acceptable accuracy, a Multipole Equivalent Source Model (ESM) with undetermined source locations has been developed for the free-space sound field prediction. …