Acoustics, Dynamics, and Controls Commons^™

Utilization Of Empirical Models To Determine The Bulk Properties Of Compressed Sound Absorptive Materials, Ruimeng Wu

Theses and Dissertations--Mechanical and Aerospace Engineering

Empirical models based on flow resistivity are commonly used to determine the bulk properties of porous sound absorbing materials. The bulk properties include the complex wavenumber and complex characteristic impedance which can be used directly in simulation models. Moreover, the bulk properties can also be utilized to determine the normal incidence sound absorption and specific acoustic impedance for sound absorbing materials of any thickness and for design of layered materials. The sound absorption coefficient of sound absorbing materials is measured in an impedance tube using wave decomposition and the measured data is used to determine the flow resistivity of the …

Development Of An Excel® Rocket Simulator For Application In Middle School, High-School, And University Stem Education, Melvin Lee Hortman

All Master's Theses

Water rocket activities are one of the most popular STEM activities used in primary, secondary, and higher education yet are void of engineering, though engineering is heavily implied in the STEM acronym. This study investigated the amount of engineering present in water rocket activities, and options for emphasizing engineering more in water rocket activities using an open-platform flight simulator for use by educators to enable students to predict flight parameters of a water rocket they designed, and test those predictions against experimental data. The simulator was constructed in Excel® with many functions, but the function validated in this study was …

Advanced Uses For Carbon Nanotubes: A Spherical Sound Source And Hot-Films As Microphones, Micaela M. Thiery

Dissertations, Master's Theses and Master's Reports

Super-aligned carbon nanotube (CNT) thin-film is used to create thermophones. The thermal properties of CNT film allow it to rapidly heat and cool when supplied AC power producing temperature and pressure gradients and, therefore, audible sound. The advantages of CNT thermophones include eliminating all moving components of traditional speakers and reducing the weight of the speaker itself by using CNT film, which is nearly weightless. Additionally, the flexibility of CNT film provides the unique opportunity to construct loudspeakers of various sizes and geometries. In this work, a spherical CNT thermophone is designed, manufactured, and tested for directivity with the overall …

Model-Based Control Of An Rcci Engine, Akshat Abhay Raut

Dissertations, Master's Theses and Master's Reports

Reactivity controlled compression ignition (RCCI) is a combustion strategy that offers high fuel conversion efficiency and near zero emissions of NOx and soot which can help in improving fuel economy in mobile and stationary internal combustion engine (ICE) applications and at the same time lower engine-out emissions. One of the main challenges associated with RCCI combustion is the difficulty in simultaneously controlling combustion phasing, engine load, and cyclic variability during transient engine operations.

This thesis focuses on developing model based controllers for cycle-to-cycle combustion phasing and load control during transient operations. A control oriented model (COM) is developed by using …

Optimization Of Acoustic Soundboard Through Modal Analysis And Material Selection, Noah C. Nicholas, Cody Gruber, Nicholas Hartman

Williams Honors College, Honors Research Projects

The purpose of this design project was to determine if it is plausible to design an acoustic top plate assembly made of a non-traditional material which is equivalent in sound quality to that of a standard wooden guitar. Since wood must be crafted by skilled luthiers, the overall cost of producing the completed product is fairly high. To reduce the cost of a finished acoustic guitar, we proposed to alter the material to that of one that is easier to manufacture, such as plastics and composites.

Based on our research, our team chose to test both ABS plastic and carbon …

On A Time Domain Boundary Integral Equation Formulation For Acoustic Scattering By Rigid Bodies In Uniform Mean Flow, Fang Q. Hu, Michelle E. Pizzo, Douglas M. Nark

Mathematics & Statistics Faculty Publications

It has been well-known that under the assumption of a uniform mean flow, the acoustic wave propagation equation can be formulated as a boundary integral equation. However, the constant mean flow assumption, while convenient for formulating the integral equation, does not satisfy the solid wall boundary condition wherever the body surface is not aligned with the assumed uniform flow. A customary boundary condition for rigid surfaces is that the normal acoustic velocity be zero. In this paper, a careful study of the acoustic energy conservation equation is presented that shows such a boundary condition would in fact lead to source …

Development And Validation Of A Tractor Drawbar Force Measurement And Data Acquisition System (Daq), James Roeber, Santosh Pitla, Roger M. Hoy, Joe D. Luck, Michael F. Kocher

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Matching agricultural tractors to implements towed by the drawbar is one of the important aspects of machinery management for ensuring optimum performance and fuel cost savings. A field deployable tractor draft force measurement and data acquisition system was developed and evaluated as part of this research project. A drawbar instrumented to measure draft force in field operating conditions was developed and statically calibrated. The drawbar was calibrated by applying loads from 4.45 to 134 kN using a hydraulic cylinder connected to a 444.8 kN load cell. Testing was conducted with the drawbar installed on a tractor on a concrete track. …

Audio-Based Productivity Forecasting Of Construction Cyclic Activities, Chris A. Sabillon

College of Graduate Studies: Theses & Dissertations

Due to its high cost, project managers must be able to monitor the performance of construction heavy equipment promptly. This cannot be achieved through traditional management techniques, which are based on direct observation or on estimations from historical data. Some manufacturers have started to integrate their proprietary technologies, but construction contractors are unlikely to have a fleet of entirely new and single manufacturer equipment for this to represent a solution. Third party automated approaches include the use of active sensors such as accelerometers and gyroscopes, passive technologies such as computer vision and image processing, and audio signal processing. Hitherto, most …

A Study Of Acoustic Reflections To Determine The Location, Size, Shape, And Orientation Of Reflecting Objects, Brandon M. Heller

Masters Theses

This study was conducted to examine the properties of sound in relation to echolocation, specifically in relation to its use by humans. Through my thesis, objects of varying shape and size were subjected to a sound wave to determine details about the object from the reflected sound. The shapes' comparisons were conducted at varying distances, measuring the intensity of the returning sound wave at several frequencies. The results demonstrated a correlation between the intensity of the sound in regards to distances, area of the reflector, and the shape of the reflector.

Simulation Of Human Ankle Trajectory During Stance Phase Of Gait, Leslie Castelino

Dissertations, Master's Theses and Master's Reports

A simulation was developed which mimics the human gait characteristics based on the input of an individual’s gait trajectory. This simulation also estimates the impedance of the human ankle based on the ground reaction forces measured by the force plate. This simulation will accept alterations of the following parameters: total body weight, weight of the shank, weight of the foot, trajectories of the shank and foot of the individual and orientation of the force plate, which would generate a new gait trajectory for the ankle during the stance phase of gait. The goal of this simulation was to validate the …

The Role Of Active Flow-Control Devices In The Dynamic Aeroelastic Response Of Wind Turbine Rotors, Muraleekrishnan Menon Menon Muraleedharan Nair

Dissertations, Master's Theses and Master's Reports

The significance of wind as a renewable source of power is growing with the increasing capacity of individual utility-scale wind turbines. Contemporary wind turbines are capable of producing up to 8 MW and consequently, their rotor sizes are rapidly growing in size. This has led to an increased emphasis on studies related to improvements and innovations in load-control methodologies. Most often than not, controlling the loads on an operational turbine is a precarious scenario, especially under high wind loading. The up-scaling of turbine rotors would thus benefit from a rationale change in load control through methodologies such as variable-speed stall, …

Multi-Modal And Short-Range Transmission Loss In Ice-Covered, Near-Shore Arctic Waters, Miles B. Penhale

Dissertations, Master's Theses and Master's Reports

In the past century, extensive research has been done regarding the sound propagation in arctic ice sheets. The majority of this research has focused on low frequency propagation over long distances. One of the most commonly used excitation methods for air-ice-water layers has been explosives. However, environmental regulation has become more stringent, disallowing the use of almost all explosive excitation types. Due to changing climate conditions in these environments, new experimentation is warranted to determine sound propagation characteristics in, through, and under thin ice sheets, in shallow water, over short distances. In April, 2016 several experiments were conducted approximately 2 …

Electromagnetic Signal Feedback Control For Proximity Detection Systems, Adam K. Smith

Dissertations, Master's Theses and Master's Reports

Coal is the most abundant fossil fuel in the United States and remains an essential source of energy. While more than half of coal production comes from surface mining, nearly twice as many workers are employed by underground operations.

One of the key pieces of equipment used in underground coal mining is the continuous mining machine. These large and powerful machines are operated in confined spaces by remote control. Since 1984, 40 mine workers in the U. S. have been killed when struck or pinned by a continuous mining machine. It is estimated that a majority of these accidents could …

Development Of A High-Fidelity Model And Kalman Filter Based State Estimator For Simulation And Control Of Nox Reduction Performance Of A Scr Catalyst On A Dpf, Venkata Rajesh Chundru

Dissertations, Master's Theses and Master's Reports

Reduction of emissions and improving the fuel consumption are two prime research areas in Diesel engine development. The present after-treatment systems being used for emissions control include diesel oxidation catalyst (DOC) for NO, HC and CO oxidation along with catalyzed particulate filters for PM (particulate matter) and selective catalytic reduction (SCR) for controlling NOx emissions. Recently an after-treatment system called SCR catalyst on a DPF capable of simultaneously reducing both NOx and PM emissions has been developed in order to reduce the overall size of the after-treatment system.

The goal of this proposed research is to create a state estimator …

Performance Of Hard Disk Drives In High Noise Environments, Trinoy Dutta

Dissertations, Master's Theses and Master's Reports

Digital information stored in rotational media, such as Hard Disk Drives (HDD) needs to be reliable and readily accessible. Various studies have been performed on the modal analysis of HDDs and the noise emitted during operation. Analysis performed by Siemens Corporation, IBM and Tyco Fire Protection Products show that HDDs are sensitive to noise. This report initially focusses on identifying the critical frequency ranges and the levels of noise where the performance of the drives reduces. A series of tests have been performed using pink noise at one-third octave frequency bands at sound pressure levels ranging from 80 dB to …

Active Management Assistant System For Embry-Riddle Ecocar 3 Hybrid Supervisory Control System, Matthew Nelson, Blair Cutting, Michael J. Aleardi

Student Works

The Embry-Riddle EcoCAR 3 team is developing a prototype hybrid Chevrolet Camaro utilizing a customized vehicle powertrain controller. This controller is serving to ensure system safety, vehicle operation, and consumer drivability while also incorporating advanced driving aids to achieve both the desired performance levels one expects from a Camaro as well as vehicle efficiency. This vehicle must reach the team set vehicle technical specifications of a 4.9 second 0 to 60 time while maintaining a 53 miles per gallon gasoline equivalence rating.

In order to reach the efficiency goal, the team is developing an Active Management Assistance System utilizing computer …

Optimal Design Of Sound Absorbing Systems With Microperforated Panels, Nicholas Nakjoo Kim

Open Access Dissertations

As the development of technology makes economic prosperity and life more convenient, people now desire a higher quality of life. This quality of life is based not only on the convenience in their life but also on clean and eco-friendly environments. To meet that requirement, much research is being performed in many areas of eco-friendly technology, such as renewable energy, biodegradable content, and batteries for electronic vehicles.

This tendency is also obvious in the acoustics area, where there are continuing attempts to replace fiber-glass sound absorbers with fiber-free materials. The combination of microperfoated panels (MPP) (one of the fiber-free sound …

Energy Localization And Heat Generation In Composite Energetic Systems Under High-Frequency Mechanical Excitation, Jesus O. Mares

Open Access Dissertations

In this work, the ability to use high frequency mechanical excitation to generate significant heating within plastic bonded explosives, as well as single energetic particles embedded within a viscoelastic binder, is studied. In this work, the fundamental mechanisms associated with the conversion of high-frequency mechanical excitation to heat as applied to these composite energetic systems are thoroughly investigated.

High-frequency contact excitation has been used to generate a significant amount of heat within samples of PBX 9501 and representative inert mock materials. Surface temperature rises on the order of 10 °C were observed at certain frequencies over a range from 50 …

3-Axis Automated Probe Traverse For Aerodynamic Testing, Tananant Boonya-Ananta, Ricky Wai, Zander Oostman, Teyvon Brooks

Mechanical Engineering

Our primary objective is to design, build, and test an automated traverse to hold measurement probes in Cal Poly’s low speed wind tunnel. The device should cause minimal flow disturbance. It’s movements must be able to cover eighty percent of the three-dimensional test section. The device should have a mounting point for interchangeable probes. The assembly is to be integrated with the current frame structure on the wind tunnel test section, and should allow very minimal deflection of the measurement probe. The user should be able to control the motion of the traverse via a computer interface which supports automatic …

Design Of A Flexible Control Platform And Miniature In Vivo Robots For Laparo-Endoscopic Single-Site Surgeries, Lou P. Cubrich

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Minimally-invasive laparoscopic procedures have proven efficacy for a wide range of surgical procedures as well as benefits such as reducing scarring, infection, recovery time, and post-operative pain. While the procedures have many advantages, there are significant shortcomings such as limited instrument motion and reduced dexterity. In recent years, robotic surgical technology has overcome some of these limitations and has become an effective tool for many types of surgeries. These robotic platforms typically have an increased workspace, greater dexterity, improved ergonomics, and finer control than traditional laparoscopic methods. This thesis presents the designs of both a four degree-of-freedom (DOF) and 5-DOF …