Structural Materials Commons^™

Surface Wetting And Friction Studies Of Nano-Engineered Surfaces On Copper Substrate, Julius Sheldon Morehead

Graduate Theses and Dissertations

Nano-engineered-textures on a material surface can dramatically improve the wetting and non-wetting properties of a surface, and they also show promise to address friction issues that affect surfaces in contact. In this work, aluminum-induced crystallization (AIC) of amorphous silicon (a-Si) was used to produce nano-textures on copper (Cu) substrates. A study was performed to examine the effects of changing the annealing conditions and a-Si thickness on nano-texture formation. The creation of various nano-topographies and chemically modifying them using octafluorocyclobutane (C4F8) was performed to control hydrophilicity, hydrophobicity, and oil affinity of nano-textured surfaces. A video-based contact angle measurement system was used …

Degradation Of Polystyrene Foam Under Radiant Heat Flux, James Butler

Graduate Theses and Dissertations

As the demand for liquefied natural gas has increased, safety concerns about the performance of transport vessels under fire conditions have been raised. Current codes for the sizing of the pressure relief systems require that the vessels are able to withstand an emmissive heat flux of 108kW/m2 and do not take into account the effects of insulation loss due to thermal decomposition of the insulation materials. To address this possible oversight in the current code models were presented to a working group organized by the Society of International Gas Tanker and Terminal Operators Ltd. focusing on the decomposition rate of …

A Quantitative Study Of The Weldability Of Inconel 718 Using Gleeble And Varestraint Test Methods, Sean Quigley

Master's Theses

Nickel super alloy Inconel 718 was tested and compared to Haynes 230 using Gleeble and Varestraint mechanical test methods. Hot cracking susceptibility was examined in either alloy using a sub-scale Varestraint test method at 5 augmented strain levels: 0.25%, 05.%, 1%, 2%, and 4%. Maximum crack length, total crack length, and number of cracks were measured for each strain level. Gleeble hot ductility on-heating and on-cooling tests were performed on both alloys. Inconel 718 was tested on-heating at target temperatures of 1600˚F, 2000˚F, 2100˚F, 2200˚F, and on cooling at 1600˚F, 1700˚F, 1800˚F, 1900˚F, and 2100˚F. Haynes 230 was tested on-heating …

Quantitative Characterization Of Microstructure Features For 1st Generation Advanced High Strength Steels, Margarita Vidrio, Ellen Liu, Donsheng Li, Kyoo Sil Choi, Xin Sun

STAR Program Research Presentations

The role of Advanced High Strength Steels (AHSS) in the automotive industry is important because of its affordability and excellent mechanical properties. The 1st generation of AHSS achieves its preferred combination of strength and ductility by embedding harder martensite grains into softer ferritic matrix. Ductility and strength of these steels are important to safety, formability, application, and life. However, a noticeable degree of inconsistent forming behaviors has been observed in the 1st generation AHSS in production, which seems to be related to the microstructure-level inhomogeneity. The objective of this project is to grain fundamental understandings on how different microstructure level …

Recycling Waste Latex Paint In Overlays, Rigid Pavements, And Pervious Concrete, Oscar Inez Quiroz

UNLV Theses, Dissertations, Professional Papers, and Capstones

With over 16 million gallons of latex paint (WLP) being disposed every year it is the largest by volume, liquid hazardous waste in the United States. WLP is difficult to recycle and hazardous to the environment due to the volatile organic compounds it contains. Several methods exist for disposing WLP including paint swaps, combustion, drying and discarding in a landfill, and by placing pigments in cement. Many communities are moving to dispose WLP by drying and placing in a landfill due to the reduced cost. However, this is the least preferred technique for the environment because it creates a need …

Mapping Mos2-Co Catalytic Nanostructures Using Hrtem And Tem Simulations, Eduan Martínez-Soto ^, Brenda Torres, Domingo Ferrer, Gilles Berhault, Russell Chianelli, Manuel Ramos *

COURI Symposium Abstracts, Summer 2011

No abstract provided.

Steel Angle Section Members Under Combined Axial Load And Unsymmetric Bending, Maheshchandra Rajasekharan Phanibhushan

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the outcome of an investigation into the experimental and theoretical behavior of steel angle section members under combined axial load and unsymmetric bending. Tests are conducted on a series of six angle section members provided with biaxial pinned-end boundaries about the cross-sectional non-principal axes. The end bending moments and axial load are applied in a quasi-static manner until the member load-carrying capacity is reached. The experimental load-deflection and load-strain curves are recorded. The theoretical analysis is based on a system of both elastic as well as materially nonlinear differential equations. The equations were solved using an iterative …

The Effects Of Damage Arrestment Devices In Composite Plate Sandwiches With Fastener Holes, Mark Anderson, Nancy Hung Choy, Lacey Jones, Rita Kourskaya

Aerospace Engineering

Composite materials such as a carbon fiber are used in a variety of new technologies including aircraft, spacecraft, and motor vehicles. Carbon fiber has a high strength to weight ratio, a key advantage over other material options. This report discusses the use of composite damage arrestment devices (DADs) in composite sandwich panels with a foam core. There are three different curing cycles tested for the DADs: pressure only, vacuum only, and vacuum with 1000 lbs of pressure. Using a Tetrahedron Heat Press to cure the composite specimen and an Instron Machine to perform tensile testing, data was collected for each …

The Effects Of Cure Schedule On Properties Of Glass-Fiber Reinforced Epoxy Matrix Composites, Trevor J. Lee

Materials Engineering

Two different two-component resin systems were cured, via Differential Scanning Calorimetry, for the times recommended by their respective manufacturers. The resin cure schedules were designed to simulate typical and attainable processing conditions; they were cured at 120°F, 140°F, and 160°F, and in-mold post-cured at 200°F, 230°F, and 260°F. The resulting scans were then compared to a baseline cure for each resin system, consisting of two heating-cooling cycles at a constant rate of temperature change. These baseline cures were then used to determine the percent cure of each sample and the shift in glass transition temperature between the baseline cure and …

Materials Characterization Of Bamboo And Analysis Of Bonding Strength And Internal Strength As A Structural Member In Reinforced Concrete, Nithi Plangsriskul, Nicholas Dorsano

Materials Engineering

This study evaluates the potential to utilize bamboo as reinforcement in concrete structural members.  In this project, the mechanical properties of bamboo were tested, specifically force required to embed a 0.5” diameter ball 0.016” into the bamboo samples and its bonding strength with concrete.  One type of bamboo, Bambusa Oldhamii, was cut into eight sections, approximately 2.54 cm wide, along the length of the culm.  The compression test recorded the bamboo’s strength at eight points along the length of the internode and at three points along the transverse direction of each specimen.  Bambusa Oldhamii’s specimen base 1 data for inner, …

Characterization Of The Relationship Between The Microstructure And Tensile Strength Of Annealed Ti-6al-4v, Aldo Corona

Materials Engineering

Tensile coupons of Ti-6Al-4V were heat treated at varying annealing temperatures from 1200°F (648°C) to 1450°F (787°C)  at 50°F  (23°C) increments for 1 hour. The samples were air cooled to room temperature or furnace cooled to 800°F (426°C) followed by air cooling to room temperature. Four tensile coupons were treated at each annealing temperature and cooling rate. Alpha case was observed to form on the surface of the samples post heat treatment with a maximum depth of 25 µm (.001 in). Samples were tensile tested for their ultimate tensile strength, yield strength, and percent elongation.  Samples across all annealing temperatures …

Investigating The Mechanical Properties Of Compression Molded Carbon Fiber Reinforced Sheet Molding Compound, Bradley A. Jones

Materials Engineering

Callaway Golf receives a proprietary blend of prepreg material from Quantum Composites. Callaway processes the prepreg in-house and supplied 254mm x 254mm x 1.3mm panels of carbon fiber sheet molding compound (CFSMC) for characterizing. Tensile strength was analyzed by conducting tensile tests per ASTM D3039. Tensile coupons were cut to 254mm long by 25.4mm wide. Tabs were constructed from 1.6mm thick GFRP printed circuit board material. A commercial grade two part epoxy was used to bond the tabs to the CFSMC. Tensile results were inconclusive due to consistent fractures occurring outside the gauge lengths of the specimens.

Flexure strength was …

Experimental Investigation Of Natural Fiber Reinforced Composite, Irene Samy Fahim

Theses and Dissertations

There is a growing use of polymers in different applications worldwide. This phenomenon resulted in an enormous increase in the amount of plastic waste. These wastes have significant impacts on the environment including pollution and depletion of resources. Recycling plastic waste and reusing it helps in alleviating environmental degradation. The amount of recycled plastics all over the world not utilized is huge. U.S.A recycled 5.7% of the total plastics generated and Western Europe recycled 39% of total amount of plastics consumed [1]. This research studies the potential usage of virgin and recycled polymer reinforced with natural fiber such as rice …

Investigating Wood Welding Parameters Using A Prototype Welding Machine, Timothy R. Melin

Master's Theses

Understanding how different processing variables influence wood welded bonds is vital if the technique will ever be used to create engineered lumber without using adhesives. A variation of vibration welding, wood welding uses pressure and friction to bond materials together. During welding, heat causes a softening in the wood, a naturally occurring composite material. This softening leads to fiber entanglement and a bond forms upon cooling.

The goal of this research was to investigate several processing aspects of the wood welding procedure. A prototype wood welding machine, designed and fabricated from the ground up, was used to investigate the effects …

Plain And Steel-Reinforced Concrete Shear Walls With And Without Cfrp Retrofitting, Ali Mohammed Salih Al Aloosi

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the outcome- of a study of the behavior and strength of plain and steel-reinforced concrete shear walls with and without a window opening and Carbon Fiber-Reinforced Polymer (CFRP) retrofitting. A total of seven tests were conducted using six different shear walls. Each wall was subjected to a gradually increasing static load at one of it's top corners until the maximum load was reached. The load-deflection relations and the walls' failure patterns were observed and recorded. It was found that the window opening in the plain concrete wall reduced the wall load capacity by 18 percent. For the …

Design, Fabrication, Structural Testing, And Numerical Analysis Of A Small Scale Composite Wing, Jacob David Gaunt, Juan Carlos Flores, Vincent Andrew Perry

Aerospace Engineering

A small scale composite wing based on a design found on an experimental aircraft was designed, constructed, and tested dynamically and statically. The wing was constructed similarly to an experimental aircraft wing. The performed static test was intended to produce pure bending. Strain gages were used to measure strains on the wing structure. The strains were converted to stresses to aid in analysis. The static test results suggested that the wing was actually under torsion. Four structural modes were found from the static test. A finite element analysis model was made to compare experimental results to numerical analytical results. The …

Performance Of Nevada’S Aggregates In Alkali-Aggregate Reactivity Of Portland Cement Concrete, Mohammad Shahidul Islam

UNLV Theses, Dissertations, Professional Papers, and Capstones

Alkali-aggregate reaction (AAR) is a form of distress that occurs in concrete and results in serviceability problems, cracks, spalling, and other deterioration mechanisms. There are two categories of AAR, namely, alkali-silica reaction (ASR) and alkali-carbonate reaction (ACR). Alkali-silica reaction is one of the most recognized deleterious phenomena in concrete, and has been a major concern since its discovery in the 1940s. The reaction which occurs between reactive silica or silicates present in some aggregates and alkalis of Portland cement produces an alkali-silica gel that expands in the presence of moisture resulting in concrete cracks. ACR is also a chemical reaction …

Mechanical Behavior Of Alloy 230 At Temperatures Relevant To Ngnp Program, Sudin Chatterjee

UNLV Theses, Dissertations, Professional Papers, and Capstones

Identification and selection of suitable structural materials for heat exchanger application within the purview of the next generation nuclear plant (NGNP) program constitute a major challenge. This challenge stems from the lack of many desired metallurgical and mechanical properties of conventional metallic materials and alloys for applications at temperatures approaching 950 oC. Nickel (Ni)-base Alloy 230 has been highly recommended as a suitable structural material for such application due to its excellent resistance to high-temperature plastic deformation and superior corrosion resistance in many hostile environments. Systematic studies on tensile, fracture toughness, creep, stress-rupture and creep-fatigue behavior of this alloy have …

Time-Temperature Curing Relationship Of An Adhesive Binder With Rice Straw, Kevin Ka-Wan Ng

Master's Theses

Rice straw is a global and proliferate agricultural waste whose production grossly outstrips viable uses. Current disposal methods are not sustainable, and more convenient methods – such as incineration – exude poor environmental stewardship. Although the direct use of straw bales in building construction presents a practical and sustainable alternative, engineering challenges associated with using it prevent its wide adoption. The Stak Block – a composite formed from compressed rice straw and a heat-cured adhesive – may overcome challenges associated with straw bale building. However, the times and temperatures needed to cure the binder with straw are not well understood. …

Multiscale Transformation Field Analysis Of Progressive Damage In Fibrous Laminates, Yehia Bahei-El-Din, Ritesh Khire, Prabhat Hajela

Centre for Advanced Materials

As part of an ongoing effort to model uncertainty propagation across multiple scales in fibrous laminates, this paper presents a deterministic transformation field analysis for modeling damage progression under membrane forces and bending moments. In this approach, equivalent eigenstresses are computed in the phases and/or plies such that their respective stress components that satisfy the underlying failure criteria are reduced to zero. Superposition of the solutions found for the undamaged laminate under applied loads and under the eigenstress field provide the entire response. Failure criteria are based on stress averages in the fiber and matrix. Damage mechanisms considered are frictional …