Polymer and Organic Materials Commons^™

Structural Design And Application Of Polymeric Silicon Elastomers, Jacob Wyant

Williams Honors College, Honors Research Projects

The purpose of this project was to determine how the polymeric structure and mechanical properties of this elastomer are affected by the ratio between the polydimethylsiloxane macromolecular chains and the crosslinkers. These were determined via tensile and compression testing. Then, spiropyran was added to observe how this fluorescence and crosslinking agent affected the elastomer. Also, the elastomer’s fluorescent and icephobic nature were tested. The elastomers with a higher ratio of crosslinker to macromolecular chain could withstand higher tensile and compressive strains but failed at lower stresses than their counterparts with lower concentrations of crosslinkers. The elastomers were also found to …

Defining The Proper Operating Time For The Septa Extractor, Abigail Jones

Williams Honors College, Honors Research Projects

Anionic polymerizations are a common type of reaction used to produce synthetic rubber. During these reactions, it is necessary to charge initiators, modifiers, and other substances, through pressurized containers that are sealed with rubber septa. These septa prevent oxygen and moisture from entering the pressurized container, and the reactor, though they need to be cleaned before use to remove other impurities. Currently a glass Soxhlet Extractor is used to remove such impurities, and though effective, it has a limited capacity, so it has to run frequently. This limitation led to the commissioning of the Septa Extractor, which is an automated …

Anti-Freeze Double Network Hydrogels, William Gross

Williams Honors College, Honors Research Projects

Three polyethylene glycol (PEG) based crosslinkers with repeat unit nominal weights of 62.1, 200, and 400 g/mol in agar/PAM double network (DN) hydrogels were used to study the effect of different crosslinkers on thermal and mechanical properties. Using the one-pot synthesis method, hydrogels with the PEG crosslinkers or methylene-bis-acrylamide (MBAA) were made via sol-gel transition for formation of agar network, and photopolymerization of the PAM network using Irgacure 2959 as photo initiator. Tensile and compression tests were performed on as prepared, swollen, and swollen & cooled specimens of each hydrogel. Freezing time and thermal imaging were performed in -20 °C …

Development Of Polymeric Sorbents As Reusable Filtration Systems For Remediation Of Pfas Contaminated Water, E. Molly Frazar

Theses and Dissertations--Chemical and Materials Engineering

Decades of use of per- and polyfluoroalkyl substances (PFAS) in a multitude of consumer and industry-based products have led to a devastating amount of soil and water contamination. Although these chemicals and compounds possess advantageous qualities – such as that of PFAS in the role of fire-fighting foams that have no doubt saved countless lives and homes, we must take responsibility for the anthropogenic hazards that threaten our global health. This entails being able to cost-effectively remediate problems created in the past from overuse of toxic substances that could negatively impact our future, and in this case, the future of …

The Application Of Photoelectron Spectroscopies In Analyzing The Impact Of Interfacial Energetics On Perovskite Solar Cells, Tuo Liu

Theses and Dissertations--Chemistry

In recent years, organic-inorganic metal halide perovskites (HP) have garnered tremendous attention in photovoltaic research. This attention is attributed to their low cost and excellent optoelectronic properties, including large absorption coefficients, tunable bandgaps, long charge-carrier diffusion lengths, and low densities of deep trap states. Inverted p-i-n architecture perovskite solar cells (PSCs) are of intense interest and are generally regarded as more amenable to low-temperature solution processing. Nevertheless, the development of inverted PSCs is lagging the conventional architecture devices. Imperfect energy level alignments and charge carrier recombination, especially at the interface between perovskite and electron transport layers (ETLs), are two main …

Higher-Order Effects In Biaxial Flexure Of Gfrp I-Section Beams, Zia Razzaq, Faridoon Z. Razzaq

Civil & Environmental Engineering Faculty Publications

A theoretical study of Glass Fiber Reinforced Polymer (GFRP) beams subjected to biaxial bending moments is presented with a focus on the influence of higher-order effects on maximum normal stresses. It is shown that the biaxial bending type of loading causes a dramatic increase in the maximum normal stress for a GFRP beam when induced torsional effects are included. The study demonstrates that the traditional first-order theory can grossly underestimate the maximum normal stress in a GFRP beam. Based on the numerical results presented using a higher-order theory which also accounts for induced warping normal stresses, the maximum normal stress …

Elastoplastic Quasi-Static And Impact Load Response Of Steel Structure Sub-Assemblage With Cfrp Strips, Ali Al Aloosi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

Presented in this paper is the outcome of an experimental investigation of the elastoplastic quasi-static and impact load response of a steel sub-assemblage constructed using a pair of hollow square section members with or without Carbon Fiber Reinforced Polymer (CFRP) strips. The sub-assemblage consists of a long structural member welded to a short member, thus representing a typical combination of a column and a beam on the face of a multi-story steel building frame. The column is subjected to a lateral quasi-static or impact load. Tests are conducted on four separate steel sub-assemblages. The first two tests are conducted with …

An Experimental Study On The Mechanical Properties And Chemical Composition Of Lcd 3d Printed Specimens, Sebastian Gomez

College of Graduate Studies: Theses & Dissertations

Additive manufacturing technologies have been enhanced throughout the years yet have surprised the manufacturing industry due to their high-end surface finish and dimensional accuracy. Different experiments have been done to identify a specific phenomenon known in the vat-polymerization field. Distortion and dimensional inaccuracy tend to affect the overall properties of the process, either physical or chemical. This approach allows the understanding of how the physical properties have been affected and how to study the chemical properties to avoid this type of phenomenon. The chemical reaction between polymer and UV light has been studied and experimented with to the point that …

Understanding The Feasibility Of Improving Interfacial Properties In Direct Ink Writing Of Silicone-Polyurethane Resin Hybrid Material, Ayobami Samuel Akinfenwa

College of Graduate Studies: Theses & Dissertations

The progress in materials engineering and the ability to make various models possible have made soft robotics a popular alternative to traditional robotics. Still, soft robots need various parts, like Printed Circuit Boards (PCBs), batteries, cables, fittings, and more, to work correctly or to get attached to other complex parts. These parts can have different material properties, like elastic moduli, strength, etc. Because of these differences, mechanical failures happen at the points where two materials meet, making soft robots less durable and less lasting in real-life situations due to failure. Conventionally, the fabrication of soft robot parts is through moulding. …

Molecular Dynamics Modeling Of Polymers For Aerospace Composites, Swapnil Sambhaji Bamane

Dissertations, Master's Theses and Master's Reports

Polymer matrix composite materials are widely used as structural materials in aerospace and aeronautical vehicles. Resin/reinforcement wetting and the effect of polymerization on the thermo-mechanical properties of the resin are key parameters in the manufacturing of aerospace composite materials. Determining the contact angle between combinations of liquid resin and reinforcement surfaces is a common method for quantifying wettability. It is challenging to determine contact angle values experimentally of high-performance resins on CNT materials such as CNT, graphene, bundles or yarns, and BNNT surfaces. It is also experimentally difficult to determine the effect of polymerization reaction on material properties of a …

Nanocomposites For Applications In Ultracapacitors Based Energy Storage Systems, Duy Pham, Jake Ivirn, Jacob Dileonardi, Ben Mckinney, Ashish Aphale

Symposium of Student Scholars

Electrochemical capacitors also known as ultracapacitor is a potential technology for modern energy storage due to their high performance of charge capacity and fast charge-discharge rates. The superior performance of ultracapacitors will help to meet demands for energy systems in applications such as transportation. Ultracapacitor device consists of electrodes, a polymeric separator, and an electrolyte. Under the applied voltage, the migration of ions between two porous electrodes from the bulk of the electrolyte governs the performance of such devices. In this work, we present experimental research on the synthesis of different electrode materials using atomically thick graphene and conducting polymers. …

Development Of Electrochemical Sensors For The Detection Of Trace Contaminants, Quang Lam, Ashish Aphale, Duy Pham

Symposium of Student Scholars

Several industrial processes, such as stainless steel fabrication and textiles, produce heavy metal byproducts such as chromium. These heavy metals have detrimental effects on the surrounding environments and humans. Recently, electrochemical-driven sensors have been studied and show great potential in miniaturization while still providing measurements at a low cost. In addition, atomically thin allotropes of carbon, graphene, and graphene oxide have shown remarkable results in producing a highly responsive and selective sensor platform. These results are due to their excellent electrical conductivity, high surface area for utility, and physicochemical stability. The existing challenge for electrochemical-driven sensors is understanding the molecular …

Nanoclays And Curcumin Based Food Packaging Material For Intelligent Food Packaging Applications, Kalpani Y. Perera, Swarna Jaiswal, Amit K. Jaiswal, Shubham Sharma

Articles

Bionanocomposite packaging eco-friendly alternatives with enhanced characteristics. This study aimed to develop a bionanocomposite intelligent packaging. Sodium alginate, gelatin, Curcumin (Cur), glycerol, and Nanoclay (NC) films were prepared. The influences of nanoclay and curcumin on the surface, optical, mechanical, chemical, barrier, and pH-indicating properties were studied. The results showed that the lightness of films was reduced by 1.28 folds compared to NC (control) film, while the yellowness of films increased by 5.82 folds. Film transparency was reduced by 9.3 folds and a 3.46 folds increase in UV barrier properties was observed compared to NC (control) film. The highest tensile strength …

Cold Plasma Technology In Food Packaging, Kalpani Y. Perera, Jack Prendeville, Amit K. Jaiswal, Swarna Jaiswal

Articles

Cold plasma (CP) is an effective strategy to alter the limitations of biopolymer materials for food packaging applications. Biopolymers such as polysaccharides and proteins are known to be sustainable materials with excellent film-forming properties. Bio-based films can be used as an alternative to traditional plastic packaging. There are limitations to biopolymer packaging materials such as hydrophobicity, poor barrier, and thermos-mechanical properties. For this reason, biopolymers must be modified to create a packaging material with the desired applicability. CP is an effective method to enhance the functionality and interfacial features of biopolymers. It etches the film surface allowing for better adhesion …

Design, Fabrication, And Characterization Of Conjugated Polymeric Electrochemical Memristors As Neuromorphic/Integrated Circuits, Benjamin Grant

All Dissertations

Organic materials are promising candidates for future electronic devices compared to the complementing inorganic materials due to their ease of processability, use, and disposal, low cost of fabrication, energy efficiency, and flexible nature toward implementation as flexible and non-conformal devices.With that in mind, electrochemical materials have been widely demonstrated with commercial use as sensors, displays, and a variety of other electronic devices. As Moore's law predicts the increase in the density of transistors on a chip, the requirement to create either smaller transistors or the replacement of the transistor device entirely is apparent. Memory resistors, coined ``memristor", are variable resistive …

Enhancing The Performance Of Poly(3-Hexylthiophene) Based Organic Thin-Film Transistors Using An Interface Engineering Method, Eyob Negussie Tarekegn

All Dissertations

An original design and photolithographic fabrication process for poly(3-hexylthiophene-2, 5-diyl) (P3HT) based organic thin-film transistors (OTFTs) is presented. The structure of the transistors was based on the bottom gate bottom contact OTFT. The fabrication process was efficient, cost-effective, and relatively straightforward to implement. Current–voltage (I-V) measurements were performed to characterize the primary electronic properties of the transistors. The measured mobility of these transistors was significantly higher than most results reported in the literature for other similar bottom gate bottom contact P3HT OTFTs. The higher mobility is explained primarily by the effectiveness of the fabrication process in keeping the interfacial layers …

Exploring The Effect Of Environmental Degradation On The Shape Memory Properties Of Polymers, Jorge Mario Avila

Open Access Theses & Dissertations

A key detriment of the use of polymers by our society is the negative effect this material class has had on the environment. A category of polymers known as shape memory polymers (SMP)s have the ability to return to a programmed original shape form after deformation to a temporary shape by using stimuli such as temperature, electrical pulses and even magnetism. The shape memory effect allows for some polymers to heal if they are damaged. This ability to heal means that components made from these materials can be reused rather than thrown away if they are damaged. The work presented …

Hierarchical Structure And Material Integration For Electrocatalytic Co2 Reduction, Hamed Mehrabi

Graduate Theses and Dissertations

CO2 released by the combustion of fossil fuels is driving significant changes to the earth’sclimate. The natural cycle for removing CO2 from the atmosphere, namely photosynthesis, cannot keep up with the rate at which it is being added. Developing engineering approaches to remove CO2 from the atmosphere is becoming essential to reduce these effects. Removal leads to further issues of carbon sequestration and favorable CO2 reuse strategies, including the electrochemical transformation of recovered CO2 to useful products such as fuels and materials. Copper is an important electrocatalyst for the CO2 reduction reaction (CO2RR) because of its unique capability for producing …

Sustainable Material For Urea Delivery Based On Chitosan Cross-Linked By Glutaraldehyde Saturated Toluene: Characterization And Determination Of The Release Rate Mathematical Model, Jayanudin Jayanudin, Retno S. D. Lestari, Indar Kustiningsih, Dandi Irawanto, Rozak Rozak, Reyonaldo L. A. Wardana, Fakhri Muhammad

Karbala International Journal of Modern Science

The aims of this study were to characterize the urea-loaded chitosan microspheres and determine the release kinetic constants and diffusion coefficients. An emulsion cross-linking method was used to prepare the urea-loaded chitosan microspheres. Urea was dissolved in a solution of chitosan then put into vegetable oil and stirred to form an emulsion. Glutaraldehyde saturated toluene (GST) was added into the emulsion dropwise while continuously stirring for the solidification process. Chitosan microspheres filled with urea were washed, dried, and then analyzed. Characterization of the urea-loaded chitosan microspheres was conducted using a scanning electron microscope (SEM), Raman spectroscopy, X-ray diffraction, and particle …

A Machine Learning Approach To Robotic Additive Manufacturing Of Uv-Curable Polymers Using Direct Ink Writing, Luis A. Velazquez

LSU Master's Theses

This thesis presents the design and implementation of a robotic additive manufacturing system that uses ultraviolet (UV)-curable thermoset polymers. Its design considers future applications involving free-standing 3D printing by means of partial UV curing and the fabrication of samples that are reinforced with fillers or fibers to manufacture complex-shape objects.

The proposed setup integrates a custom-built extruder with a UR5e collaborative manipulator. The capabilities of the system were demonstrated using Anycubic resin formulations containing fumed silica (FS) at varying weight fractions from 2.8 to 8 wt%. To fully cure the specimens after fabrication, a UV chamber was used. Then, measurements …