Open Access. Powered by Scholars. Published by Universities.®

Polymer and Organic Materials Commons™

Open Access. Powered by Scholars. Published by Universities.®

969 Full-Text Articles 1,801 Authors 720,793 Downloads 93 Institutions

All Articles in Polymer and Organic Materials

Faceted Search

969 full-text articles. Page 12 of 45.

Lignin Copolymer Property Prediction Using Machine Learning, Collin Larsen 2023 University of Arkansas, Fayetteville

Lignin Copolymer Property Prediction Using Machine Learning, Collin Larsen

Chemical Engineering Undergraduate Honors Theses

Lignin, an abundant biopolymer, is a waste byproduct of the paper and pulp industry. Despite its renewable nature and potential applicability in various products, such as plastics and composites, the development of lignin-based materials has been impeded by the cumbersome, Edisonian process of trial and error. This research proposes a novel approach to forecasting the properties of lignin-based copolymers by utilizing a recurrent neural network (RNN) based on the Keras models previously created by Tao et al. Example units of modified lignin were synthesized via esterification and amination functional group modifications. To increase the efficiency and accuracy of the prediction …


Separation Of Organic Acids Through Direct Catalysis From Sugars, Katelyn Robinson 2023 University of Arkansas, Fayetteville

Separation Of Organic Acids Through Direct Catalysis From Sugars, Katelyn Robinson

Chemical Engineering Undergraduate Honors Theses

Society relies on plastic products, whether they are single use or durable. A downside of plastic is that the most common type is a product of oil and oil is not only a limited resource but also a climate-damaging resource. Polylactic acid (PLA) is a bio-based, biodegradable plastic. However, the process of converting biomass to polylactic acid polymer has the largest environmental impact of the PLA production process, so alternative methods of conversion are needed (Moretti et al., 2021). The polylactic acid polymer can be made with lactic acid, which can be converted from glucose.


Analytical And Experimental Investigation Of Interphase And Dispersion Effects On The Mechanical Stiffness Of Cellulose Nanocomposites, Will Goldberg 2023 Washington University in St. Louis

Analytical And Experimental Investigation Of Interphase And Dispersion Effects On The Mechanical Stiffness Of Cellulose Nanocomposites, Will Goldberg

McKelvey School of Engineering Graduate Student Theses & Dissertations

The effect of dispersion and interphase properties on the elastic behavior of cellulose nanocomposites was investigated using a number of composite models, experimental data and a thorough literature review. Cellulose nanocomposites consisting of soy protein isolate (SPI) and cellulose nanocrystals (CNC) or polydopamine coated cellulose nanocrystals (PD-CNC) were prepared via solution casting method and tested for mechanical stiffness. These outcomes were compared to standard composite models as well as novel methods adapted from the literature that incorporate data regarding dispersion quality and interphase properties. The literature review verified that both dispersion and interphase properties are highly dependent on interfacial chemistry …


Poly(Ether Imide)S: Synthesis And Properties, Rachel Price 2023 Murray State University

Poly(Ether Imide)S: Synthesis And Properties, Rachel Price

Honors College Theses

The synthesis of strong polymers is crucial to the creation of heat-resistant, durable, and mechanically useful plastics that we use every day. Poly(ether imide)s are used in applications such as food service, aerospace, automotive, and many more. This thesis will discuss the synthesis and properties of these plastics to help express a larger understanding of these polymers.


Shape Memory Polymer-Based Multifunctional Syntactic Foams, Siavash Sarrafan 2023 Louisiana State University and Agricultural and Mechanical College

Shape Memory Polymer-Based Multifunctional Syntactic Foams, Siavash Sarrafan

LSU Doctoral Dissertations

With the increase in popularity of shape memory polymers (SMPs), especially in applications such as aerospace, textile, biomedical engineering, and even structures, the weight of the material and the devices made with it has always been a crucial factor. Using the shape memory polymer as a matrix to make a syntactic foam is one of the best and most affordable approaches to creating a lighter material that still has the shape memory effect. The addition of particles of different stiffness, strength, and size, with variable fractions, creates a composite that enables engineering the mechanical, as well as other physical and …


The Influence Of Diamine Curing Additives On The Network Architecture Of Phthalonitrile Thermosetting Polymers, Tyler J. Richardson 2023 The University of Southern Mississippi

The Influence Of Diamine Curing Additives On The Network Architecture Of Phthalonitrile Thermosetting Polymers, Tyler J. Richardson

Dissertations

Phthalonitrile monomers undergo diamine-promoted polymerization by a complex reaction mechanism involving two competitive cure pathways, forming two primary network architectures: linear polyisoindoline chains and branched triazine crosslinks. The influence of the diamine curing additive on the polymerization pathway, and the influence of the resulting network architectures on cured network properties, have not been adequately explored within the phthalonitrile field. Two structurally different diamine curing additives, bis[4-(3-aminophenoxy)phenyl] sulfone (mBAPS) and 1,3-phenylenebis((4-(4-aminophenoxy)phenyl)methanone) (AEK-134), were studied for the polymerization of resorcinol phenylphosphate phthalonitrile (RPPhPN), where the influence of diamine structure and concentration on the polymerization behavior, network architecture, and bulk thermal and thermomechanical …


Flexible Materials And Applications For Wearable Sensors, Brock Ferrari 2023 Liberty University

Flexible Materials And Applications For Wearable Sensors, Brock Ferrari

Senior Honors Theses

This literature review aimed to address the limitations of rigid wearable sensors in the medical community by investigating the development of flexible materials for remote health monitoring. A keyword search was conducted on Google Scholar, PubMed, and the Jerry Falwell Library, which yielded 9,102 articles. After applying filtering techniques, the results were narrowed down to 21 articles, which were categorized into "Present Market Conditions," "Flexible Materials for Medical Use," "Applications for Wearable Sensors," and "Potential Use Cases." Discussions were held on prominent materials such as substrate, nanocomposite, and liquid metal materials, exploring their potential applications for chemical and physical sensing, …


Additive Manufacturing For Phase Change Thermal Energy Storage And Management, Thomas B. Freeman 2023 Embry-Riddle Aeronautical University

Additive Manufacturing For Phase Change Thermal Energy Storage And Management, Thomas B. Freeman

Doctoral Dissertations and Master's Theses

Phase change materials can enhance the performance of energy systems by time shifting or reducing peak thermal loads. Certain electronic devices such as batteries, laser systems, or electric vehicle power electronics are highly transient and require pulse heat dissipation. Heat sinks, or thermal management devices made of a phase change material can absorb large heat spikes while maintaining a constant temperature. Additive manufacturing techniques hold tremendous potential to enable co-optimization of material properties and device geometry, while potentially reducing material waste and manufacturing time. Recently, a few efforts have emerged that employ additive manufacturing techniques to integrate a phase change …


Hydrothermal Liquefaction Of Saccharina Latissima For The Production Of Biofuel, Mayokun A. Oke 2023 University of Texas at Tyler

Hydrothermal Liquefaction Of Saccharina Latissima For The Production Of Biofuel, Mayokun A. Oke

Mechanical Engineering Theses

We performed hydrothermal liquefaction of brown macroalga (Saccharina latissima) in the presence of homogenous and heterogenous catalysts such as KOH, Na2CO3, Pd/C, HZSM-5, Ce/HZSM-5, and Ni/SiO2-Al2O3 in hot compressed water, to investigate their effects on product yield and composition in the biocrude. To investigate hydrocarbon production, we used methanol as co-solvent (methanol-to-water 1/4 vol.%) and as the only liquefaction solvent. We carried out the experiments in a batch reactor at 330oC and 120-130 bar, and varying temperature, algae-to-water ratio, residence time, and pretreatment method. The biocrude yields …


Hybrid Modeling For Electrochemical Systems, Luis Alejandro Briceno-Mena 2023 Louisiana State University and Agricultural and Mechanical College

Hybrid Modeling For Electrochemical Systems, Luis Alejandro Briceno-Mena

LSU Doctoral Dissertations

The discovery of new materials like catalysts, polymeric films, and biomolecules, is driven by industrial needs such as improving reaction or separation selectivity, enhancing therapeutic effects on medical treatments, or reducing costs of replacement. However, deployment of these advances in industrial applications is often hindered by the lack of models needed for design and optimization. Due to the novelty of materials and devices, experimental data and first principles' knowledge are scarce, making it hard to build models either via data-driven or knowledge based approaches. In this context, a way to efficiently combine domain knowledge with data could provide a pathway …


Polyethersulfone Thin-Film Nanocomposite Membrane Embedded With Amine-Functionalized Graphene Oxide For Desalination Applications, Ahmed Bahaeldin 2023 American University in Cairo

Polyethersulfone Thin-Film Nanocomposite Membrane Embedded With Amine-Functionalized Graphene Oxide For Desalination Applications, Ahmed Bahaeldin

Theses and Dissertations

Thin-film nanocomposite (TFN) desalination membranes were prepared based on a polyethersulfone (PES) support, where the polyamide (PA) layer was embedded with amine-functionalized graphene oxide (GO). The effect of adding various concentrations of functionalized and un-functionalized GO on the desalination performance, hydrophilicity, and morphology of the membranes was additionally assessed throughout this work. Scanning electron microscopy (SEM) measurements were used to assess the morphology of the membranes in combination with Brunauer-Emmett-Teller (BET) analysis. Contact angle measurements were used to gauge the hydrophilicity of the synthesized membranes. The membrane with the best desalination performance contained 1x10-3 wt/vol% of functionalized GO in …


Constructing A Fine Dispersion And Chemical Interface Based On An Electrostatic Self-Assembly And Aqueous Phase Compound In Go/Sio2/Sbr Composites To Achieve High-Wear Resistance In Eco-Friendly Green Tires, Rui Zhang, Jiaye Li, Stephen Jerrams, Shui Hu, Shipeng Wen, Ligun Zhang 2023 Beijing University of Chemical Technology, Beijing, China

Constructing A Fine Dispersion And Chemical Interface Based On An Electrostatic Self-Assembly And Aqueous Phase Compound In Go/Sio2/Sbr Composites To Achieve High-Wear Resistance In Eco-Friendly Green Tires, Rui Zhang, Jiaye Li, Stephen Jerrams, Shui Hu, Shipeng Wen, Ligun Zhang

Articles

The hazard to the ecosystem caused by rubber microparticles generated from tire abrasion has been a constant concern. Therefore, to protect this ecosystem, the development of a tire tread with high abrasion resistance is especially significant. Herein, γ-aminopropyltriethoxysilane (APTES) was used to modify graphene oxide (GO) and silica (SiO2) to obtain GO and SiO2 with positive charges (NG and NS). Furthermore, NG and NS were electrostatically self-assembled by using maleic anhydride (MAH) hydrolysis, thereby obtaining composite particles (NG-NS) with “bridged structures”. Also, the NG-NS/styrene butadiene rubber (SBR) compounds possessing fine dispersion of NG-NS were prepared by the aqueous compounding method. …


Drop Wetting And Sliding On Soft, Swollen Elastomers, Zhuoyun Cai 2023 University of Kentucky

Drop Wetting And Sliding On Soft, Swollen Elastomers, Zhuoyun Cai

Theses and Dissertations--Chemical and Materials Engineering

Soft, slippery surfaces have gained increasing attention due to their wide range of potential applications, for example in self-cleaning, anti-fouling, liquid collection, and more. One design approach in creating slippery surfaces is using a swollen elastomer, which is a polymer network swollen with a lubricant. This type of surface may be beneficial for longer-term use than standard lubricant-infused surfaces, and provides a versatile surface with tunable mechanical properties. Hence, understanding the physics of soft surface interactions is important for fundamental soft matter physics, biomaterials, adhesives, and coatings. This research experimentally investigates wetting on soft infused networks, with the aim of …


Solid-State Shear Pulverization: A Comprehensive Study On Polymer Processing Technology From A Systematic Innovation Perspective, Tyler A. Will 2023 Bucknell University

Solid-State Shear Pulverization: A Comprehensive Study On Polymer Processing Technology From A Systematic Innovation Perspective, Tyler A. Will

Master’s Theses

Solid-state shear pulverization (SSSP) is a continuous and scalable processing technique that imposes mechanochemical changes in polymer-based materials. It has been shown to impart beneficial properties onto homopolymers or create copolymers and composites through continuous fragmentation and fusion. The unique technology employs cold temperature to keep the polymer in the solid state. This thesis investigates industrial polymer processing in the context of real-world applications. This thesis analyzes SSSP using an organized methodology called systematic innovation (SI). SI facilitates problem solving by assisting engineers in conducting root cause analysis around a material and studying the physical setup of the equipment.

This …


Temperature-Dependent Diffusion In Block Copolymer Organogels, Ridwana Bashar 2023 Bucknell University

Temperature-Dependent Diffusion In Block Copolymer Organogels, Ridwana Bashar

Master’s Theses

Organogels are often considered for transport-based applications such as transdermal drug delivery vehicles and gel actuators due to their unique properties. Recent consideration of styrenic block copolymer based organogels’ application in transdermal drug delivery requires an extensive investigation of drug diffusion behavior through these gels to assess their applicability. Temperature is a major influencing parameter on diffusion. The goal of this research is to better understand the impact of temperature on diffusion in styrenic triblock copolymer organogels. To accomplish this goal, we focused on three specific objectives: (i) accurately measure the diffusivities of a solute – AOT reverse micelles – …


Beeswax Wraps As An Alternative To Single-Use Plastics, Sarah Skiver 2023 The University of Akron

Beeswax Wraps As An Alternative To Single-Use Plastics, Sarah Skiver

Williams Honors College, Honors Research Projects

The project goal was to compare the food storage efficacy of sustainable beeswax wraps verses the single-use plastic methods of resealable plastic sandwich bags and plastic cling wrap. The goal was also to test the reusability of the beeswax wraps, as it is a key advantage of beeswax wraps that is advertised. The project purpose was to explore sustainable and eco-friendly alternatives to single use plastics, which are harmful to the environment in both their production and their disposal. Food spoilage was compared in beeswax wrap, plastic sandwich bags, and plastic cling wrap, and spoilage was also observed in a …


Defining The Proper Operating Time For The Septa Extractor, Abigail Jones 2023 The University of Akron

Defining The Proper Operating Time For The Septa Extractor, Abigail Jones

Williams Honors College, Honors Research Projects

Anionic polymerizations are a common type of reaction used to produce synthetic rubber. During these reactions, it is necessary to charge initiators, modifiers, and other substances, through pressurized containers that are sealed with rubber septa. These septa prevent oxygen and moisture from entering the pressurized container, and the reactor, though they need to be cleaned before use to remove other impurities. Currently a glass Soxhlet Extractor is used to remove such impurities, and though effective, it has a limited capacity, so it has to run frequently. This limitation led to the commissioning of the Septa Extractor, which is an automated …


An Experimental Study On The Mechanical Properties And Chemical Composition Of Lcd 3d Printed Specimens, Sebastian Gomez 2023 Georgia Southern University

An Experimental Study On The Mechanical Properties And Chemical Composition Of Lcd 3d Printed Specimens, Sebastian Gomez

College of Graduate Studies: Theses & Dissertations

Additive manufacturing technologies have been enhanced throughout the years yet have surprised the manufacturing industry due to their high-end surface finish and dimensional accuracy. Different experiments have been done to identify a specific phenomenon known in the vat-polymerization field. Distortion and dimensional inaccuracy tend to affect the overall properties of the process, either physical or chemical. This approach allows the understanding of how the physical properties have been affected and how to study the chemical properties to avoid this type of phenomenon. The chemical reaction between polymer and UV light has been studied and experimented with to the point that …


Understanding The Feasibility Of Improving Interfacial Properties In Direct Ink Writing Of Silicone-Polyurethane Resin Hybrid Material, Ayobami Samuel Akinfenwa 2023 Georgia Southern University

Understanding The Feasibility Of Improving Interfacial Properties In Direct Ink Writing Of Silicone-Polyurethane Resin Hybrid Material, Ayobami Samuel Akinfenwa

College of Graduate Studies: Theses & Dissertations

The progress in materials engineering and the ability to make various models possible have made soft robotics a popular alternative to traditional robotics. Still, soft robots need various parts, like Printed Circuit Boards (PCBs), batteries, cables, fittings, and more, to work correctly or to get attached to other complex parts. These parts can have different material properties, like elastic moduli, strength, etc. Because of these differences, mechanical failures happen at the points where two materials meet, making soft robots less durable and less lasting in real-life situations due to failure. Conventionally, the fabrication of soft robot parts is through moulding. …


Elastoplastic Quasi-Static And Impact Load Response Of Steel Structure Sub-Assemblage With Cfrp Strips, Ali Al Aloosi, Zia Razzaq 2023 Old Dominion University

Elastoplastic Quasi-Static And Impact Load Response Of Steel Structure Sub-Assemblage With Cfrp Strips, Ali Al Aloosi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

Presented in this paper is the outcome of an experimental investigation of the elastoplastic quasi-static and impact load response of a steel sub-assemblage constructed using a pair of hollow square section members with or without Carbon Fiber Reinforced Polymer (CFRP) strips. The sub-assemblage consists of a long structural member welded to a short member, thus representing a typical combination of a column and a beam on the face of a multi-story steel building frame. The column is subjected to a lateral quasi-static or impact load. Tests are conducted on four separate steel sub-assemblages. The first two tests are conducted with …


Digital Commons powered by bepress