Materials Science and Engineering Commons^™

Fabrication And Characterization Of Nanomaterials Grown By Electron Beam Induced Deposition Process, Juntao Li

Legacy Theses & Dissertations (2009 - 2024)

Platinum&ndash and tungsten&ndashcontaining materials were grown on bulk substrates from a variety of precursors including (CH₃)₃CH₃C₅H₄Pt, W(CO)₆, WF₆, and Pt(PF₃)₄ in either a high vacuum dual beam focused ion beam/scanning electron microscope (FIB&ndashSEM) or an environmental scanning electron microscope (ESEM). The effects of deposition conditions on the growth kinetics, microstructure and composition of the grown materials, structural and chemical homogeneity of impurities inside the deposits as well as the resistivity were investigated.

Nanoabrasives Retention And Removal Mechanisms In Polyurethane Pads For Copper Cmp, Iftikhar Ul-Hasan

Legacy Theses & Dissertations (2009 - 2024)

The continued reduction in integrated circuit (IC) feature size requires similar reductions in surface defectivity. A key source of surface defects in IC fabrication processes stems from nanoabrasives used in chemical-mechanical planarization (CMP) processing. During CMP processing, polished surfaces are more vulnerable to defects including scratching, nanoabrasive particle adhesion and nanoabrasive agglomerate adhesion. The removal of these nano-sized particles is a priority for the IC fabrication industry and is reflected in the 2008 ITRS defect budget. However, there is insufficient technical understanding regarding the retention of residual nanoabrasives on the surfaces of the CMP pad following a CMP process and …

Suppression Of Octahedral Tilts And Associated Changes In Electronic Properties At Epitaxial Oxide Heterostructure Interfaces, A. Y. Borisevich, H. Y. Chang, Mark Huijben, M. P. Oxley, S. Okamoto, Manish K. Niranjan, John D. Burton, Evgeny Y. Tsymbal, Y. H. Chu, P. Yu, R. Ramesh, Sergei V. Kalinin, S. J. Pennycook

Materials Research Science and Engineering Center: Faculty Publications

Epitaxial oxide interfaces with broken translational symmetry have emerged as a central paradigm behind the novel behaviors of oxide superlattices. Here, we use scanning transmission electron microscopy to demonstrate a direct, quantitative unit-cell-by-unit-cell mapping of lattice parameters and oxygen octahedral rotations across the BiFeO₃ -La_0:7 Sr_0:3MnO₃ interface to elucidate how the change of crystal symmetry is accommodated. Combined with low-loss electron energy loss spectroscopy imaging, we demonstrate a mesoscopic antiferrodistortive phase transition near the interface in BiFeO₃ and elucidate associated changes in electronic properties in a thin layer directly adjacent to the interface.

Experimental Study On Thermal Treatment Of Used Printed Wiring Boards (Pwbs), Xiangjun Zuo

Masters Theses

The availability of cheaper and better electronic products as a result of the rapid innovation in technology in past decades has driven the production of e-waste forward. Printed wiring board (PWB) is a component made of one or more layers of insulating material with electrical conductors. The existing processes of recycling PWBs use pyrometallurgical or hydrometallurgical methods, which generate atmospheric pollution. Green recycling has obvious benefits to decrease the amount of PWBs. Green recycling includes two features, 1) little or zero pollution of toxic gases and heavy metals, and 2) efficient (quick and economical) recycling.

The aim of this work …

Sintering And Microstructural Effects On Mechanical Properties Of Zirconium Carbide-Tungsten Cermets, Melissa M. Giles Craft

Masters Theses

"Zirconium carbide-tungsten cermets were prepared by in situ reaction sintering a mixture of zirconia and tungsten carbide. Tungsten is a refractory metal with a melting point of 3422⁰C; however, its mechanical strength decreases significantly with increasing temperature. One approach to improve the elevated temperature strength is to add ceramic particulates to the matrix. Zirconia and tungsten carbide were compacted and then reacted and sintered in a single step by heating to 2050⁰C. The resulting stoichiometric zirconium carbide-tungsten cermet had a relative density greater than 96%. Cermets with two different grain sizes were produced by altering the final sintering temperature. Sintering …

Electrochemical Characterization Of Cerium-Based Conversion Coatings On Al 7075-T6, Simon Joshi

Doctoral Dissertations

"This research used electrochemical techniques to characterize the deposition and corrosion protection behavior of cerium-based conversion coatings on AI 7075-T6. Alkaline activation decreased native oxide impedance (5.9 kΩ-cm²) by ~25% promoting deposition of 250-500 mn coatings. Activation in NaOH solutions deposited coatings with large cracks and craters, whereas Na₂C0₃ activation resulted in uniform coatings, i.e., fewer cracks and almost no craters. Uniformly deposited coatings exhibited better cathodic inhibition and higher impedance (~200 kΩ-cm²) than on NaOH activated substrates (~100 kΩ-cm²). Subsurface crevices, caused by Cl⁻ and H₂O₂ in the deposition solution, were found under large cracks and craters. Thus, Na₂CO₃ …

Characterization Of The Corrosion Protection Mechanism Of Cerium-Based Conversion Coatings On High Strength Aluminum Alloys, William R. Pinc

Doctoral Dissertations

"The aim of the work presented in this dissertation is to investigate the corrosion protection mechanism of cerium-based conversion coatings ( CeCCs) used in the corrosion protection of high strength aluminum alloys. The corrosion resistance of CeCCs involves two general mechanisms; barrier and active. The barrier protection mechanism was influenced by processing parameters, specifically surface preparation, post-treatment, and the use of gelatin. Post-treatment and the addition of gelatin to the coating solution resulted in fewer cracks and transformation of the coating to CeP0₄, which increased the corrosion resistance by improving the barrier aspect of CeCCs. CeCCs were found to best …

Phosphate Post-Treatment Of Cerium-Based Conversion Coatings On Al 2024-T3, Daimon K. Heller

Doctoral Dissertations

"Phosphate post-treatment of cerium-based conversion coatings (CeCCs) on high strength aluminum alloys can significantly improve corrosion resistance. As-deposited CeCCs exhibit corrosion pits and salt tails across the specimen surface after 3 days of exposure, but post-treated CeCCs have withstood 14 days of salt spray exposure without visibly corroding. The morphology, phase, and electrochemical properties of spray deposited CeCCs were affected by post-treatment parameters such as immersion time, solution temperature, and phosphate source. The best performing coatings were post-treated in aqueous orthophosphate solutions for at least 5 min at temperatures of at least 85⁰C. These conditions converted cerium hydroxy/peroxy species in …

Characterization Of Diamond Thin Films And Related Materials, Travis K. Mckindra

Doctoral Dissertations

"Thin carbon films including sputtered deposited graphite and CO₂ laser-assisted combustion-flame deposited graphite and diamond thin films were characterized using optical and electron microscopy, X-ray diffraction and micro-Raman spectroscopy. Amorphous carbon thin films were deposited by DC magnetron sputtering using Ar/O₂ gases. The film morphology changed with the oxygen content. The deposition rate decreased as the amount of oxygen increased due to oxygen reacting with the growing film. The use of oxygen in the working gas enhanced the crystalline nature of the films. Graphite was deposited on WC substrates by a CO₂ laser-assisted O₂/C₂H₂ combustion-flame method. Two distinct microstructural areas …

Foundry Parameters For Casting High-Aluminum Lightweight Steel In Complex Shapes, Angella Marie Schulte

Masters Theses

"This work investigated the liquid metal treatment and molding practices for Fe- 30wt.%Mn-9wt.%Al-1wt.%Si-0.9wt.%C-0.5wt.%Mo steel. The goal of this research was to determine the process conditions that would produce a tough Fe-Mn-Al-C alloy and the appropriate mold design to produce a defect-free P900 plate.

Notch toughness of age-hardenable Fe-Mn-Al-C alloys decreases as phosphorus increases. Thermodynamic calculations and experimental work show that additions of Ca followed by Ce can be used to mitigate the deleterious effects of phosphorus, and the addition of Ar-stirring can be used to decrease the number of harmful aluminum nitride inclusions. In the solution-treated and aged condition (Brinell …

The Properties And Structure Of Tin Phosphate Glasses Modified With Other Oxides, Jong Wook (Austin) Lim

Masters Theses

"The main objective of this research was to evaluate the properties and structures of glasses from the stannous (SnO) phosphate system for possible use in low temperature optical applications. Glasses in the binary xSnO-(100-x)P₂O₅ system (50 ≤ x ≤ 70) were prepared and their thermal and optical properties were evaluated. Differences in glass transition temperatures (T_g) measured here and reported in the literature were explained by differences in the residual water content in the glasses, as determined by infrared spectroscopy. In general, increasing the SnO content of the binary glasses increased the refractive index and the glass transition …

Electroless Deposition Of Superconducting Magnesium Diboride Thin Films On Various Substrates, Khrupa Saagar Vijayaragavan

Wayne State University Theses

ABSTRACT

ELECTROLESS DEPOSITION OF SUPERCONDUCTING MAGNESIUM DIBORIDE THIN FILMS ON VARIOUS SUBSTRATES

by

KHRUPA SAAGAR VIJAYARAGAVAN

MAY 2010

Advisor: Dr. Susil K Putatunda

Dr. Gavin Lawes

Major: Chemical Engineering

Degree: Masters of Science

Superconducting thin films of magnesium diboride were synthesized by a novel electroless plating process. Electroless plating shares many similarities to electroplating with the major difference being the absence of a continuous bias voltage. Significantly, this work represents the first investigation where electroless deposition has been used to prepare compounds, as opposed to the elemental metals considered in all previous studies. Magnesium Diboride is a recently discovered superconducting …

Electrostatic Quadrupole Plasma Mass Spectrometer Measurements During Thin Film Depositions Using Simultaneous Matrix Assisted Pulsed Laser Evaporation And Magnetron Sputtering, Chad N. Hunter, Michael H. Check, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

A hybrid plasma deposition process, combining matrix assisted pulsed laser evaporation (MAPLE) of carbon nanopearls (CNPs) with magnetron sputtering of gold was investigated for growth of composite films, where 100 nm sized CNPs were encapsulated into a gold matrix. Composition and morphology of such composite films was characterized with x-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM) analysis. Carbondeposits on a gold magnetron sputter target and carbon impurities in the gold matrices of depositedfilms were observed while codepositing from gold and frozen toluene-CNP MAPLE targets in pure argon. Electrostatic quadrupole plasma analysis was used to determine that …

Environmental Degradation Of Oxidation Resistant And Thermal Barrier Coatings For Fuel-Flexible Gas Turbine Applications, Prabhakar Mohan

Electronic Theses and Dissertations

The development of thermal barrier coatings (TBCs) has been undoubtedly the most critical advancement in materials technology for modern gas turbine engines. TBCs are widely used in gas turbine engines for both power-generation and propulsion applications. Metallic oxidation-resistant coatings (ORCs) are also widely employed as a stand-alone protective coating or bond coat for TBCs in many high-temperature applications. Among the widely studied durability issues in these high-temperature protective coatings, one critical challenge that received greater attention in recent years is their resistance to high-temperature degradation due to corrosive deposits arising from fuel impurities and CMAS (calcium-magnesium-alumino-silicate) sand deposits from air …

Morphological, Structural, And Optical Studies Of Undoped And Doped-Zno Nanostructure., Ramin Yousefi

Student Works (2010-2019)

Research concerning one-dimensional nanomaterials has grown tremendously ever since carbon nanotubes were discovered by Iijima (1991), silicon nanowires were grown by Lieber's group (1998), and ZnO nanowires and nanobelts were found by Wang's group from Georgia Tech (Pan et al., 2001). Such researches on one-dimensional structures have been one of the most important branches of science during recent decades. We can now observe the impact of these studies on the technology of one-dimensional materials and also the advanced prospect of developing new technologies. Based on this motivation, this thesis attempts to investigate some unknown properties of ZnO nanostructures as …

A Study On The Corrosion Behavior Of Nanocrystalline Nickel In Aqueous Environments, Anjana Shyam Sundar

Material Science and Engineering Theses - Archive

Nanocrystalline materials possess considerably enhanced properties arising from their small grain size. Significant interest has been paid in the past to their mechanical and physical properties. Very little attention has been attracted by their electrochemical behavior, which is expected to be affected by the significant volume fraction of grain boundaries. In the present study, corrosion experiments were conducted in nanocrystalline nickel in two entirely different solutions in order to obtain a better understanding of its corrosion behavior. This is of particular interest to MEMS and NEMS devices where electroplated nanocrystalline nickel is the metal of choice. The corrosion behavior of …

Branched And Spiral Organic Nanotubes Based On The Self-Assembly Of Bile Acids, Xuejun Zhang

Electronic Theses and Dissertations

The self-assembly of chiral amphiphilic molecules in aqueous solutions is of particular interest because the chirality of individual molecules is often expressed in their supermolecular structures. Self-assembled tubes made of chiral amphiphilic molecules represent useful supramolecular architectures which hold promise as controlled release vehicles for drug delivery, encapsulates for functional molecules, and nanoreactors for chemical reactions. Lithocholic acid (LCA) is a secondary bile acid with the concentration being identical to that of cholesterol in the hepatic bile and gallbladder. It has a rigid, nearly planar hydrophobic steroid nucleus, with four hydrogen atoms and one hydroxyl group directed toward the concave …

Structural Characterization Of Sputter-Deposited Ss304+Xal (X = 0, 4, 7 And 10 Wt.%) Coatings And Mechanically Milled Ti, Zr And, Uma Maheswara Seelam

Electronic Theses and Dissertations

Study of the metastable phases obtained by non-equilibrium processing techniques has come a long way during the past five decades. New metastable phases have often given new perspectives to the research on synthesis of novel materials systems. Metastable materials produced by two non-equilibrium processing methods were studied for this dissertation- 304-type austenitic stainless steel (SS304 or Fe-18Cr-8Ni)+aluminum coatings produced by plasma enhanced magnetron sputter-deposition (PEMS) and nanocrystalline Ti, Zr and Hf powders processed by mechanical milling (MM). The objective of the study was to understand the crystallographic and microstructural aspects of these materials. Four SS304+Al coatings with a nominal Al …

Microstructural Investigation Of Precipitation Hardened Cuni2s+Zr Alloys For Rotor Applications, Jean-Paul Vega-Garcia

Electronic Theses and Dissertations

Industrial generator components experience high stresses and electrical fields during their service life. Material integrity is key in guaranteeing component performance. CuNi2SiZr, used as rotor wedges in generators, serve to maintain rotor slot content in place while experiencing high centrifugal stresses and low cycle fatigue during start and stop at elevated temperature. The quality and integrity of this material in service can be directly related to its microstructure, which is determined by the processing procedures of the wedges. In this study, the microstructure development in this material is evaluated to eliminate grain boundary defects by optimizing processing parameters, determining the …

Investigation Of Thermal, Elastic And Load-Biased Transformation Strains In Niti Shape Memory Alloys, Shipeng Qiu

Electronic Theses and Dissertations

Polycrystalline NiTi shape memory alloys have the ability to recover their original, pre-deformed shape in the presence of external loads when heated through a solid-solid phase transformation from a lower-symmetry B19' martensite phase to a higher-symmetry B2 austenite phase. The strain associated with a shape memory alloy in an actuator application typically has thermal, elastic and inelastic contributions. The objective of this work was to investigate the aforementioned strains by recourse to in situ neutron diffraction experiments during selected combinations of heating, cooling and/or mechanical loading. The primary studies were conducted on polycrystalline Ni49.9Ti50.1 specimens on the Spectrometer for MAterials …