Materials Science and Engineering Commons^™

Resistance Switching In Electrodeposited Magnetite Thin Films, Samantha Glen Matthews

Masters Theses

"The resistance switching phenomenon has been extensively studied in metal oxide thin films for its applications in the non-volatile memory industry. The research presented here focuses on magnetite thin films which have been electrodeposited onto gold-sputtered glass substrates via the electrochemical reduction of a Fe(III)-triethanolamine complex in aqueous alkaline solution. Magnetite was chosen for its usefulness in read/write memory applications, its high Curie temperature, its metal-to-insulator (Verwey) transition, and its half-metallic character and attendant spintronic properties. Resistance switching behavior caused by a reversible redox reaction at the anode was observed in the films, demonstrating that electrodeposited films show the same …

Evaluation Of Alternative Methods For Surface Preparation And Deposition Of Cerium-Based Conversion Coatings On Aluminum Alloys, William J. Gammill

Masters Theses

"This thesis investigates alternative surface preparation and deposition methods for cerium-based conversion coatings (CeCC) on high strength aluminum alloys. Cerium-based conversion coatings are being investigated as a more environmentally friendly replacement for chromium-based conversion coatings. Currently, the alloys are immersed in strong alkaline and acidic solutions to prepare the aluminum surfaces for conversion coating, in which immersion may not be suitable for all situations. Alternatives to this method were investigated, including wipe application of solution, ultrasonic processing in deionized water, and abrasive blasting with alumina. AI 7075-T6 test panels were prepared using each of these methods and compared to a …

Synthesis And Characterization Of Limpo[4] (M=Mn, Ni And Fe) Olivine Materials., Azlin Sanusi

Student Works (2010-2019)

Lithium transition metal phosphate, LiMPO4 compounds with olivine structure namely LiMnPO4, LiNiPO4 and LiFePO4 were successfully synthesized in the present work. LiMnPO4 and LiNiPO4 were synthesized by the sol-gel method with tartaric acid as the chelating agent. LiFePO4 was synthesized via the chemical precipitation and low temperature sterilizer heating method. TGA was carried out on LiMnPO4 and LiNiPO4 samples to determine the firing temperature of the gel precursor and the thermal stability of the prepared samples. LiMnPO4 was heated for 15 hours at various temperatures and LiNiPO4 was formed at 1000 oC with firing time of 24 hours. Firing of …

Inductively Coupled Plasma Dry Etching Process On Planar Lightwave Circuit Fabrication., Chuah Khoon Seah

Student Works (2010-2019)

The main objective of this project is to master state-of-the-art techniques and knowledge in silica etching in order to achieve high quality waveguide circuit on Planar Lightwave Circuit devices. Another objective is to optimize the clean room research strength, surface characterization, microscopy techniques and similar semiconductor manufacturing processes.Initially, these processes were conducted with wet etching method that utilized diluted hydrofluoric acid (HF) and buffered oxide etch (BOE). Several problems arising such as mask peel-off, poor sidewall profile and defect waveguide channel during the pattern transfer process due to its’ isotropic nature. Alternatively, dry etching method was conducted via Inductively Coupled …

An Ab-Initio Study Of The Elastic Properties Of Important Group Iv Diborides At High Temperatures, Manny Gonzales

Open Access Theses & Dissertations

Presented is an ab-initio Molecular Dynamics (MD) study, employing the Density Functional Theory (DFT), of the lattice parameter, thermal expansion coefficients and elastic constants of ZrB₂, TiB₂ and HfB₂ as a function of temperature. The MD trajectories provide the equilibrium lattice parameters at finite temperatures, and the gradient of the energy from these equilibrium solutions is then used to calculate the components of the stiffness tensor. The results for ZrB₂ are shown to agree well with reported experimental results for the lattice parameters and elastic constants as a function of temperature.

Sensitivity Analysis Of The Johnson-Cook Plasticity Model For Hypervelocity Impacts: A Hydro-Code Study, Carlos David Castellanos

Open Access Theses & Dissertations

Computer simulations have been in use for decades in the modeling of hypervelocity impacts and general large deformation problems. Several computer codes have been developed to simulate this type of problems under a variety of geometric configurations and for any number of materials. These codes make use of several constitutive material models to simulate the response of the material under a variety of thermo-mechanical conditions. The Johnson-Cook constitutive model is widely used in the simulation hypervelocity impacts for the simulation of crater formation and even perforation of target structures. This thesis presents the results of a sensitivity study of this …

Selection Process, Modified Impact Testing And Failure Analysis Of An Electron-Beam-Melted Ti-6al-4v 3d Tessellation Based On The Eulerian Path Of The First Stellation Of The Rhombic Dodecahedron Open Unit Cell, Hugo Lopez

Open Access Theses & Dissertations

Ti-6Al-4V lattice block structures manufactured through the electron beam melting (EBM) process are a promising field in design and research due to great advantages that the alloy, the process and the final product offer. Three lattice block structures were manufactured through the electron beam process using an ARCAM A2 machine. The structures were designed using the MATERIALIZE^TM software and were designed around different types of unit cells. Compression testing was performed and one unit cell was selected due to its anisotropic behavior for modified impact testing. The same unit cell was used and it was scaled up to add …

Processing Of Zrb2-Zrc-Zrxsiy Ceramic By Reactive Metal Penetration, Nischel B. Maheswaraiah

Open Access Theses & Dissertations

The processing of ZrB2-ZrC-ZrxSiy composite by reactive metal penetration was investigated as a successor to the ZrB2-SiC composites for hypersonic vehicles application, which cannot be used for extended time at temperatures greater than 1600C due to formation of SiO and CO gases. Zirconium (Zr), zirconium disilicide (ZrSi2), and boron carbide (B4C) were reacted in graphite crucibles for 60, 120, 180, and 240 minutes. Microscopy and x-ray diffraction (XRD) deduced the formation of a heterogeneous microstructure of ZrB2-ZrC-ZrxSiy precipitates surrounded by a solidified Zr-Si melt. Unreacted boron carbide was observed in samples held at 1860C for 60 minutes and 120 minutes, …

Microstructure Investigation Of Al-Rich Titanium Aluminum Alloys, David Pham

Open Access Theses & Dissertations

The microstructures of Ti-Al alloys with 70-80 wt% Al were investigated. Aluminum wire (99.999%) and TiH₂ powder (99.7%) were used to produce the sample compositions inside a vertical tube furnace at 1600^oC in an Ar atmosphere. Argon is purified through a dehumidification and deoxidation system. Magnesium perchlorate Mg(ClO₄)₂ acts as a desiccant and titanium sponge pulls oxygen from the Ar in furnaces operating at 800^oC and 750^oC. X-ray diffraction and an optical microscope are used to identify phases and compositions

Spectroscopic Study Of The Inhibition Of Calcium Oxalate Calculi By Larrea Tridentata, Luis Alonso Pinales

Open Access Theses & Dissertations

The causes of urolithiasis include such influences as diet, metabolic disorders, and genetic factors which have been documented as sources that aggravate urinary calculi depositions and aggregations, and, implicitly, as causes of urolithiasis. This study endeavors to detail the scientific mechanisms involved in calcium oxalate calculi formation, and, more importantly, their inhibition under growth conditions imposed by the traditional medicinal approach using the herbal extract, Larrea tridentata. The calculi were synthesized without and with Larrea tridentata infusion by employing the single diffusion gel technique. A visible decrease in calcium oxalate crystal growth with increasing amounts of Larrea tridentata herbal infusion …

The Reactivity Of A Zr-Si Melt With B4c At Ultrahigh Temperatures, Alvaro Vega Sandate

Open Access Theses & Dissertations

Surfaces with exceptional properties are needed for next generation materials. Hypersonic re-entry space vehicles or turbines are subjected to both oxidizing and neutral environments and nose-caps or wings on such vehicles could easily reach operating temperatures of over 2000°C. Ultrahigh temperature ceramics like ZrB2 and HfB2 have melting temperatures of 3245°C and 3380°C respectively. However, these materials need to be protected from oxidation, usually with an oxide layer. Zirconium is more affordable and will be used to study its reaction with B4C and ZrSi2.

Experimentation was conducted by melting Zr slugs into a B4C and ZrSi2 packed bed at 1860°C …

Resistive Switching Of Tin Dioxide (Sno2) For Memristor Applications, Sergio Fabian Almeida

Open Access Theses & Dissertations

In the last decades new electrical devices have been investigated in order to overcome problems caused by integrated circuit shrinking. Within these devices there is one that has attracted much attention due to its high scalability and simple structure. This device was proposed theoretically by Leon Chua in 1971 who gave it the name of "Memristor". In the recent years thin films structures composed of a metal/oxide/metal (MOM) stack have been linked to this new device, also known as "Resistive switching". There are several applications for the memristor; one of the most important is for resistive random access memory (ReRAM) …

Influence Of Fraction Of High Angle Boundaries On The Mechanical Behavior Of An Ultrafine Grained Al-Mg Alloy, R. Kapoor, N. Kumar, R. S. Mishra, C. S. Huskamp, K. K. Sankaran

Materials Science and Engineering Faculty Research & Creative Works

The mechanical behavior of ultrafine grained AA5052 processed through different techniques-rolled, annealed, friction stir processed (FSP) and equal channel angular pressed (ECAP)-were compared and correlated with microstructure. the microstructure was characterized using electron back scattered diffraction to obtain the boundary spacing, the fraction of high angle boundaries and to estimate the dislocation density from local misorientations. Both FSP and ECAP conditions had ultrafine boundary spacing, but the fraction of high angle boundaries was larger for the FSP condition. Tensile deformation carried out at 297K, and 10-3s-1 showed a lower work-hardening rate and recovery rate for FSP as compared to the …

Friction Stir Processing Of Commercial Grade Marine Alloys To Enable Superplastic Forming, Christopher B. Smith, Arun Mohan, Rajiv S. Mishra, Murray Mahoney, Mike Miles, Scott M. Gillis, Lee M. Cerveny, Gerald Opichka

Materials Science and Engineering Faculty Research & Creative Works

The use of friction stir processing (FSP) on marine grade aluminum sheet has been investigated with the objective of locally enhancing the material properties. This can potentially allow low-cost commercial grade aluminum to be used in superplastic forming applications or further enhance the formability to allow more complex geometries to be formed. FSP has been demonstrated to enable super plasticity (uniform elongations >250%) in 5083-H116 over a range of friction stir processing conditions. © (2010) Trans Tech Publications.

An Analysis Of Strength And Ductility Of Ultrafine Grained Al Alloys, R. Kapoor, P. S. De, R. S. Mishra

Materials Science and Engineering Faculty Research & Creative Works

This paper brings together and compares data of various ultrafine grained (UFG) Al alloys processed through different routes. in general, the trend of decreasing ductility with increasing strength was observed for the UFG alloys. as compared to the coarse grained (CG) alloys, the UFG alloys show a lower ductility, a lower extent of work-hardening and a lower uniform elongation. Unlike the CG alloys, which show a large fraction of uniform to total elongation, in UFG alloys this fraction varies with processing technique. It is shown here that aging of some UFG Al alloys improves ductility. Further, it is shown that …

Impedance Spectroscopy Of Batio₃ Cubes Suspended In Lossy Liquids As A Physical Model Of Two-Phase System, Piotr Z. Jasinski, Vladimir Petrovsky, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Impedance spectroscopy techniques were used for analysis of the physical model in a two-phase system toward determining of dielectric constant of dielectric particles suspended in liquids at various solids loading (volume fraction) levels. Model experimental studies were conducted using BaTiO3 as a dielectric material that was prepared as small cubes of uniform size (2×2×1 mm). Barium titanate (BT) cubes having a dielectric constant of 3850 were immersed in liquids of low dielectric constant and moderate electrical conductivity. Measured impedance spectra consisted of two semicircles, which were fitted for (R∥C)(R∥C) equivalent circuit. The parameters obtained from fitting were compared with the …

Effect Of Phosphorus On Cleavage Fracture In Κ-Carbide, N. I. Medvedeva, Ryan A. Howell, David C. Van Aken, Julia E. Medvedeva

Materials Science and Engineering Faculty Research & Creative Works

To understand the origin of cleavage fracture which dominates in Fe(Mn)-Al-C alloys at a high phosphorus concentration, we performed first-principles study of the phosphorus effect on ideal cleavage energy and critical stress in κ-carbide, Fe₃ AlC, a precipitate in the austenitic alloys. We find that phosphorus has higher solubility in Fe₃ AlC than in γ-Fe and sharply reduces the cleavage characteristics of κ-carbide. We show that strong anisotropy of the Fe-P bonds in Fe₃ (Al,P) C under tensile stress, leads to the appearance of large structural voids and may facilitate crack nucleation.

Strain-Stiffening In Synthetic And Biopolymer Networks, Kendra Erk, Kevin J. Henderson, Kenneth R. Shull

School of Materials Engineering Faculty Publications

Strain-stiffening behavior common to biopolymer networks is difficult to reproduce in synthetic networks. Physically associating synthetic polymer networks can be an exception to this rule and can demonstrate strain-stiffening behavior at relatively low values of strain. Here, the stiffening behavior of model elastic networks of physically associating triblock copolymers is characterized by shear rheometry. Experiments demonstrate a clear correlation between network structure and strain-stiffening behavior. Stiffening is accurately captured by a constitutive model with a single fitting parameter related to the midblock length. The same model is also effective for describing the stiffening of actin, collagen, and other biopolymer networks. …

Hybrid Manufacturing: Integrating Stereolithography And Direct Print Technologies, Amit Lopes

Open Access Theses & Dissertations

The focus of this research was the development of a hybrid manufacturing system that integrates stereolithography (SL) and direct print (DP) technologies to fabricate three dimensional (3D) structural electronic devices within a single set-up. The capabilities of this new additive manufacturing (AM) technology was explored in the context of fabricating and prototyping complex electronic devices in which conformal shape, rugged and light-weight integration, and a natural resistance to reverse engineering are all of paramount importance. Consequently, electronic components can be tightly integrated together in a rugged, light-weight 3D structure of arbitrary form. This research is a continuing advancement of the …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …