Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

16,808 Full-Text Articles 33,201 Authors 8,321,852 Downloads 190 Institutions

All Articles in Materials Science and Engineering

Faceted Search

16,808 full-text articles. Page 613 of 616.

Investigation Of The Threshold Voltage Shift Effect Of La2o3 On Tin/Hfo2/La2o3/Sio2/Si Stacks, Ming Di 2010 University at Albany, State University of New York

Investigation Of The Threshold Voltage Shift Effect Of La2o3 On Tin/Hfo2/La2o3/Sio2/Si Stacks, Ming Di

Legacy Theses & Dissertations (2009 - 2024)

The semiconductor industry continues to scale (shrink) transistor dimensions to both increase the number of transistors per integrated circuit and their speed. One important aspect of scaling is the need to decrease the equivalent oxide thickness of the transistor gate dielectric while minimizing leakage current. Traditional thin layer SiO2 or SiOxNy films have been replaced by higher dielectric constant film stacks Here we study one example, the HfO2/La2O3/SiO2 stack. This dissertation describes an investigation of the use of La2O3 to reduce the threshold voltage of TiN/HfO2/SiO2/Si stacks (high-k/metal gate stacks). A significant aspect of this study is the determination of …


Fabrication And Characterization Of Nanomaterials Grown By Electron Beam Induced Deposition Process, Juntao Li 2010 University at Albany, State University of New York

Fabrication And Characterization Of Nanomaterials Grown By Electron Beam Induced Deposition Process, Juntao Li

Legacy Theses & Dissertations (2009 - 2024)

Platinum&ndash and tungsten&ndashcontaining materials were grown on bulk substrates from a variety of precursors including (CH3)3CH3C5H4Pt, W(CO)6, WF6, and Pt(PF3)4 in either a high vacuum dual beam focused ion beam/scanning electron microscope (FIB&ndashSEM) or an environmental scanning electron microscope (ESEM). The effects of deposition conditions on the growth kinetics, microstructure and composition of the grown materials, structural and chemical homogeneity of impurities inside the deposits as well as the resistivity were investigated.


Nanoabrasives Retention And Removal Mechanisms In Polyurethane Pads For Copper Cmp, Iftikhar Ul-Hasan 2010 University at Albany, State University of New York

Nanoabrasives Retention And Removal Mechanisms In Polyurethane Pads For Copper Cmp, Iftikhar Ul-Hasan

Legacy Theses & Dissertations (2009 - 2024)

The continued reduction in integrated circuit (IC) feature size requires similar reductions in surface defectivity. A key source of surface defects in IC fabrication processes stems from nanoabrasives used in chemical-mechanical planarization (CMP) processing. During CMP processing, polished surfaces are more vulnerable to defects including scratching, nanoabrasive particle adhesion and nanoabrasive agglomerate adhesion. The removal of these nano-sized particles is a priority for the IC fabrication industry and is reflected in the 2008 ITRS defect budget. However, there is insufficient technical understanding regarding the retention of residual nanoabrasives on the surfaces of the CMP pad following a CMP process and …


Suppression Of Octahedral Tilts And Associated Changes In Electronic Properties At Epitaxial Oxide Heterostructure Interfaces, A. Y. Borisevich, H. Y. Chang, Mark Huijben, M. P. Oxley, S. Okamoto, Manish K. Niranjan, John D. Burton, Evgeny Y. Tsymbal, Y. H. Chu, P. Yu, R. Ramesh, Sergei V. Kalinin, S. J. Pennycook 2010 Oak Ridge National Laboratory, Oak Ridge, Tennessee

Suppression Of Octahedral Tilts And Associated Changes In Electronic Properties At Epitaxial Oxide Heterostructure Interfaces, A. Y. Borisevich, H. Y. Chang, Mark Huijben, M. P. Oxley, S. Okamoto, Manish K. Niranjan, John D. Burton, Evgeny Y. Tsymbal, Y. H. Chu, P. Yu, R. Ramesh, Sergei V. Kalinin, S. J. Pennycook

Materials Research Science and Engineering Center: Faculty Publications

Epitaxial oxide interfaces with broken translational symmetry have emerged as a central paradigm behind the novel behaviors of oxide superlattices. Here, we use scanning transmission electron microscopy to demonstrate a direct, quantitative unit-cell-by-unit-cell mapping of lattice parameters and oxygen octahedral rotations across the BiFeO3 -La0:7 Sr0:3MnO3 interface to elucidate how the change of crystal symmetry is accommodated. Combined with low-loss electron energy loss spectroscopy imaging, we demonstrate a mesoscopic antiferrodistortive phase transition near the interface in BiFeO3 and elucidate associated changes in electronic properties in a thin layer directly adjacent to the interface.


Electroless Deposition Of Superconducting Magnesium Diboride Thin Films On Various Substrates, Khrupa Saagar Vijayaragavan 2010 Wayne State University

Electroless Deposition Of Superconducting Magnesium Diboride Thin Films On Various Substrates, Khrupa Saagar Vijayaragavan

Wayne State University Theses

ABSTRACT

ELECTROLESS DEPOSITION OF SUPERCONDUCTING MAGNESIUM DIBORIDE THIN FILMS ON VARIOUS SUBSTRATES

by

KHRUPA SAAGAR VIJAYARAGAVAN

MAY 2010

Advisor: Dr. Susil K Putatunda

Dr. Gavin Lawes

Major: Chemical Engineering

Degree: Masters of Science

Superconducting thin films of magnesium diboride were synthesized by a novel electroless plating process. Electroless plating shares many similarities to electroplating with the major difference being the absence of a continuous bias voltage. Significantly, this work represents the first investigation where electroless deposition has been used to prepare compounds, as opposed to the elemental metals considered in all previous studies. Magnesium Diboride is a recently discovered superconducting …


Friction Stir Processing Of Commercial Grade Marine Alloys To Enable Superplastic Forming, Christopher B. Smith, Arun Mohan, Rajiv S. Mishra, Murray Mahoney, Mike Miles, Scott M. Gillis, Lee M. Cerveny, Gerald Opichka 2010 Missouri University of Science and Technology

Friction Stir Processing Of Commercial Grade Marine Alloys To Enable Superplastic Forming, Christopher B. Smith, Arun Mohan, Rajiv S. Mishra, Murray Mahoney, Mike Miles, Scott M. Gillis, Lee M. Cerveny, Gerald Opichka

Materials Science and Engineering Faculty Research & Creative Works

The use of friction stir processing (FSP) on marine grade aluminum sheet has been investigated with the objective of locally enhancing the material properties. This can potentially allow low-cost commercial grade aluminum to be used in superplastic forming applications or further enhance the formability to allow more complex geometries to be formed. FSP has been demonstrated to enable super plasticity (uniform elongations >250%) in 5083-H116 over a range of friction stir processing conditions. © (2010) Trans Tech Publications.


Investigation Of The Thermoelectric Behavior Of Cu-Doped Pbteagxse, Ben Ma 2010 Clemson University

Investigation Of The Thermoelectric Behavior Of Cu-Doped Pbteagxse, Ben Ma

All Theses

Sustainable energy research is currently on the forefront of scientific exploration thus a major effort is devoted to the development of new energy conservation and production techniques. Thermoelectric materials can play a significant part both in energy conservation and energy production via the Seebeck effect (heat to electric power) and the Peltier effect (electricity to cooling power), since they can convert wasted heat to useful electrical energy.
Presented herein are the measured electrical and thermal transport properties and phenomenal analysis of the PbTeAgxSe (x=1.9, 2.0, 2.01) system. First, it would lead to a significant reduction in the thermal conductivity and …


Understanding Materials, Petros J. Katsioloudis 2010 Old Dominion University

Understanding Materials, Petros J. Katsioloudis

STEMPS Faculty Publications

The article discusses the importance of understanding the characteristics of materials that will be used for different applications. Through the years, the inventions and innovations in the technology of materials are becoming more technologically complex. Innovations in the materials are divided in different categories, including metals, ceramics, polymers and composites. Example of such innovations in the technology of materials include the ceramic composite applied to the surface of the space shuttle panels to absorb and release high amounts of heat.


Electrostatic Quadrupole Plasma Mass Spectrometer Measurements During Thin Film Depositions Using Simultaneous Matrix Assisted Pulsed Laser Evaporation And Magnetron Sputtering, Chad N. Hunter, Michael H. Check, Christopher Muratore, Andrey A. Voevodin 2010 Air Force Research Laboratory

Electrostatic Quadrupole Plasma Mass Spectrometer Measurements During Thin Film Depositions Using Simultaneous Matrix Assisted Pulsed Laser Evaporation And Magnetron Sputtering, Chad N. Hunter, Michael H. Check, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

A hybrid plasma deposition process, combining matrix assisted pulsed laser evaporation (MAPLE) of carbon nanopearls (CNPs) with magnetron sputtering of gold was investigated for growth of composite films, where 100 nm sized CNPs were encapsulated into a gold matrix. Composition and morphology of such composite films was characterized with x-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM) analysis. Carbondeposits on a gold magnetron sputter target and carbon impurities in the gold matrices of depositedfilms were observed while codepositing from gold and frozen toluene-CNP MAPLE targets in pure argon. Electrostatic quadrupole plasma analysis was used to determine that …


Foundry Parameters For Casting High-Aluminum Lightweight Steel In Complex Shapes, Angella Marie Schulte 2010 Missouri University of Science and Technology

Foundry Parameters For Casting High-Aluminum Lightweight Steel In Complex Shapes, Angella Marie Schulte

Masters Theses

"This work investigated the liquid metal treatment and molding practices for Fe- 30wt.%Mn-9wt.%Al-1wt.%Si-0.9wt.%C-0.5wt.%Mo steel. The goal of this research was to determine the process conditions that would produce a tough Fe-Mn-Al-C alloy and the appropriate mold design to produce a defect-free P900 plate.

Notch toughness of age-hardenable Fe-Mn-Al-C alloys decreases as phosphorus increases. Thermodynamic calculations and experimental work show that additions of Ca followed by Ce can be used to mitigate the deleterious effects of phosphorus, and the addition of Ar-stirring can be used to decrease the number of harmful aluminum nitride inclusions. In the solution-treated and aged condition (Brinell …


The Properties And Structure Of Tin Phosphate Glasses Modified With Other Oxides, Jong Wook (Austin) Lim 2010 Missouri University of Science and Technology

The Properties And Structure Of Tin Phosphate Glasses Modified With Other Oxides, Jong Wook (Austin) Lim

Masters Theses

"The main objective of this research was to evaluate the properties and structures of glasses from the stannous (SnO) phosphate system for possible use in low temperature optical applications. Glasses in the binary xSnO-(100-x)P₂O₅ system (50 ≤ x ≤ 70) were prepared and their thermal and optical properties were evaluated. Differences in glass transition temperatures (Tg) measured here and reported in the literature were explained by differences in the residual water content in the glasses, as determined by infrared spectroscopy. In general, increasing the SnO content of the binary glasses increased the refractive index and the glass transition …


Zinc Iron Phosphate Glasses For Enameling Applications, Sagnik Saha 2010 Missouri University of Science and Technology

Zinc Iron Phosphate Glasses For Enameling Applications, Sagnik Saha

Masters Theses

"New compositions of low temperature black glasses were developed that are suitable as frits for enameling soda-lime silicate (S-L-S) glass substrates. Zinc iron phosphate glasses are of interest for this application because they possess dilatometric low softening points (under 600ºC) and have coefficients of thermal expansion that are compatible with S-L-S glass (in the range 90-110x10⁻⁷/ºC). The development of compositions with excellent chemical durability, particularly in acidic conditions, is also desired. Compositional modification were made to the (Na₂O+K₂O)·ZnO·MnO·Fe₂O₃·P₂O₅ glass system using design of experiments. The compositional boundaries used in the design were based on earlier work at Missouri S&T. The …


Fluid Flow Related Phenomena And Inclusion Motion In Continuous Casting Strands, Yufeng Wang 2010 Missouri University of Science and Technology

Fluid Flow Related Phenomena And Inclusion Motion In Continuous Casting Strands, Yufeng Wang

Doctoral Dissertations

"To improve the efficiency of the continuous casting process and the quality of its products, this dissertation mainly investigated fluid flow related phenomena and inclusion motion in continuous casting. Mathematical simulation was performed for this purpose. Both a slab caster and a billet caster were investigated. In the study of the slab caster, the application of electromagnetic brake field on the slab mold was evaluated. The results indicated that the magnetic force decelerated the high speed steel jet, stabilized the top fluctuation, and prevented the bias flow inside the mold. The other study of this slab caster involved the fluid …


Synthesis And Characterization Of Conducting Polymer Nanostructures And Their Application In Sensors, Zhe-Fei Li 2010 Missouri University of Science and Technology

Synthesis And Characterization Of Conducting Polymer Nanostructures And Their Application In Sensors, Zhe-Fei Li

Doctoral Dissertations

"A one-step synthesis technique has been used to fabricate sensors by growing polyaniline nanofibers and polyaniline/metal nanocomposites in the active area of an interdigitated electrode array. Polyaniline nanofiber sensors can be fabricated by irradiating an aqueous precursor solution containing aniline, HCl, a metal salt, and ammonium persulfate (APS) with a high pressure Hg lamp. The sensors are ready for operation after polymerization is complete, and no additional processing steps are necessary. These sensors showed faster and more intensity response to various organic vapors than conventional bulk polyaniline sensors due to their larger surface area. A chemisorption model and a diffusion …


Characterization Of Diamond Thin Films And Related Materials, Travis K. McKindra 2010 Missouri University of Science and Technology

Characterization Of Diamond Thin Films And Related Materials, Travis K. Mckindra

Doctoral Dissertations

"Thin carbon films including sputtered deposited graphite and CO₂ laser-assisted combustion-flame deposited graphite and diamond thin films were characterized using optical and electron microscopy, X-ray diffraction and micro-Raman spectroscopy. Amorphous carbon thin films were deposited by DC magnetron sputtering using Ar/O₂ gases. The film morphology changed with the oxygen content. The deposition rate decreased as the amount of oxygen increased due to oxygen reacting with the growing film. The use of oxygen in the working gas enhanced the crystalline nature of the films. Graphite was deposited on WC substrates by a CO₂ laser-assisted O₂/C₂H₂ combustion-flame method. Two distinct microstructural areas …


Phase Equilibria In Iron Phosphate System, Liying Zhang 2010 Missouri University of Science and Technology

Phase Equilibria In Iron Phosphate System, Liying Zhang

Doctoral Dissertations

"The main objectives of this research were to synthesize iron phosphate compounds, study phase equilibria in the iron phosphate system, focusing on the glass forming area, and investigate glass formability and properties based on the liquidus regions. Twelve iron phosphate compounds were successfully prepared and studied in terms of liquidus temperature or decomposition behavior. The liquidus surface of the Fe₃PO₇- Fe(PO₃)₃ system was re-determined and found to be significantly different from that originally presented by Wentrup in 1935. Eutectic points exist at 58.0 mole% Fe₂O₃ (1070⁰C), 42.7 mole% Fe₂O₃ (925°C), and 37.0 mole% Fe₂O₃ (907°C). The latter two eutectic points …


Environmental Degradation Of Oxidation Resistant And Thermal Barrier Coatings For Fuel-Flexible Gas Turbine Applications, Prabhakar Mohan 2010 University of Central Florida

Environmental Degradation Of Oxidation Resistant And Thermal Barrier Coatings For Fuel-Flexible Gas Turbine Applications, Prabhakar Mohan

Electronic Theses and Dissertations

The development of thermal barrier coatings (TBCs) has been undoubtedly the most critical advancement in materials technology for modern gas turbine engines. TBCs are widely used in gas turbine engines for both power-generation and propulsion applications. Metallic oxidation-resistant coatings (ORCs) are also widely employed as a stand-alone protective coating or bond coat for TBCs in many high-temperature applications. Among the widely studied durability issues in these high-temperature protective coatings, one critical challenge that received greater attention in recent years is their resistance to high-temperature degradation due to corrosive deposits arising from fuel impurities and CMAS (calcium-magnesium-alumino-silicate) sand deposits from air …


Morphological, Structural, And Optical Studies Of Undoped And Doped-Zno Nanostructure., Ramin Yousefi 2010 Universiti Malaya

Morphological, Structural, And Optical Studies Of Undoped And Doped-Zno Nanostructure., Ramin Yousefi

Student Works (2010-2019)

Research concerning one-dimensional nanomaterials has grown tremendously ever since carbon nanotubes were discovered by Iijima (1991), silicon nanowires were grown by Lieber's group (1998), and ZnO nanowires and nanobelts were found by Wang's group from Georgia Tech (Pan et al., 2001). Such researches on one-dimensional structures have been one of the most important branches of science during recent decades. We can now observe the impact of these studies on the technology of one-dimensional materials and also the advanced prospect of developing new technologies. Based on this motivation, this thesis attempts to investigate some unknown properties of ZnO nanostructures as …


A Study On The Corrosion Behavior Of Nanocrystalline Nickel In Aqueous Environments, Anjana Shyam Sundar 2010 University of Texas at Arlington

A Study On The Corrosion Behavior Of Nanocrystalline Nickel In Aqueous Environments, Anjana Shyam Sundar

Material Science and Engineering Theses - Archive

Nanocrystalline materials possess considerably enhanced properties arising from their small grain size. Significant interest has been paid in the past to their mechanical and physical properties. Very little attention has been attracted by their electrochemical behavior, which is expected to be affected by the significant volume fraction of grain boundaries. In the present study, corrosion experiments were conducted in nanocrystalline nickel in two entirely different solutions in order to obtain a better understanding of its corrosion behavior. This is of particular interest to MEMS and NEMS devices where electroplated nanocrystalline nickel is the metal of choice. The corrosion behavior of …


Branched And Spiral Organic Nanotubes Based On The Self-Assembly Of Bile Acids, Xuejun Zhang 2010 University of Central Florida

Branched And Spiral Organic Nanotubes Based On The Self-Assembly Of Bile Acids, Xuejun Zhang

Electronic Theses and Dissertations

The self-assembly of chiral amphiphilic molecules in aqueous solutions is of particular interest because the chirality of individual molecules is often expressed in their supermolecular structures. Self-assembled tubes made of chiral amphiphilic molecules represent useful supramolecular architectures which hold promise as controlled release vehicles for drug delivery, encapsulates for functional molecules, and nanoreactors for chemical reactions. Lithocholic acid (LCA) is a secondary bile acid with the concentration being identical to that of cholesterol in the hepatic bile and gallbladder. It has a rigid, nearly planar hydrophobic steroid nucleus, with four hydrogen atoms and one hydroxyl group directed toward the concave …


Digital Commons powered by bepress