Electrocatalytic Determination Of 15 Kinds Of Phenolic Compounds By Novel Gold Nanoparticles-Modified Glassy Carbon Electrode,
2011
School of Environmental Studies, China University of Geosciences, Wuhan 430074, China;
Electrocatalytic Determination Of 15 Kinds Of Phenolic Compounds By Novel Gold Nanoparticles-Modified Glassy Carbon Electrode, Yan-Ping Cui, Wei-Xing Wang, Chang-Zhu Yang, Wen-Hong Pu
Journal of Electrochemistry
A gold nanoparticles modified glassy carbon electrode (Au/GCE) was used to detect 15 kinds of phenolic compounds. In the cyclic voltammetry measurements, the peak currents of phenolic compounds at Au/GCE were all increased as compared with GCE and planar gold electrodes, and the oxidation potentials were determined by the activity of analytes. Besides, electrocatalysis of salicylic acid was studied at Au/GCE. The results showed that, there was a good linear relationship between the oxidation current and the concentration of salicylic acid, and the current sensitivity was 1.8 fold higher than that obtained on GCE. Trace phenolic compounds determination could be …
Preparation And Characterization Of Casno3 Anode Material For Lithium Ion Batteries,
2011
College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 Fujian,China
Preparation And Characterization Of Casno3 Anode Material For Lithium Ion Batteries, Ran Sun, Zi-Geng Liu, Ya-Qi Jiang
Journal of Electrochemistry
In this study the precursor CaSn(OH)6 was prepared via a hydrothermal process, and its composition, surface feature and phase-transition were characterized by XRD, SEM and DSC-TGA. The shapes of CaSn(OH)6 crystals were effectively controlled by adjusting the volumn ratio of H2O and CH3CH2OH solvents. Perovskite CaSnO3 could be obtained by calcination of CaSn(OH)6 at 800 ℃. The reversible capacity of 334.4 mAh/g with good cycling stability could be achieved with the CaSnO3 electrode.
Preparation And Characterization Of The Lani0.6Fe0.4O3-δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell,
2011
Institute of Fuel Cell, School of Mechanical Engineering, Shanghai jiaotong lniversity, Shanghai 200240,China
Preparation And Characterization Of The Lani0.6Fe0.4O3-δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell, Hang Liu, Bo Huang, Xin-Jian Zhu
Journal of Electrochemistry
The LaNi0.6Fe0.4O3-δ as cathode material for intermediate temperature solid oxide fuel cell was prepared using a combustion synthesis technique. The X-ray diffraction (XRD) pattern showed that the single-phase LaNi0.6Fe0.4O3-δ perovskite could be obtained after heat treatment at 600°C. The TEM and SEM images of the synthesized powders revealed that the grains were 50-100nm. According to the electrochemical impedance spectra (EIS), the polarization resistance of the symmetric cell LaNi0.6Fe0.4O3-δ/ScSZ/LaNi0.6Fe0.4O3-δ sintered at 1050°C was the smallest (0.70Ω·cm2, 0.27Ω·cm2 …
Preparation And Application Of Macroporous Ato/Sio2 Electrode In Electrochemical Degradation Of 4-Chlorophenol,
2011
Faculty of Material Seience and Chemical Engineering, Ningbo University, Ningbo 315211, Zhejiang, China
Preparation And Application Of Macroporous Ato/Sio2 Electrode In Electrochemical Degradation Of 4-Chlorophenol, Zhang-Lin Chai, Rui-Feng Zhang, Tong-Hu Xiao, Yun-Xiao Liang
Journal of Electrochemistry
The macroporous ATO/SiO2 materials were prepared through multiple steps of hydrolysis deposition in ethylene glycol and acetonitrile mixed solutions of SnCl2/SbCl3 and subsequent calcination at high temperature. The structures of the obtained materials were characterized by means of SEM and XRD. The results showed that the nano-ATO chemically deposited on the SiO2 support underwent well-controlled aggregation and recrystallization to form a sandwich structure (ATO-SiO2-ATO). Through four times loading of ATO the volume resistivity and the specific surface area reached 10·cm and 77 m2·g-1, respectively. The oxygen evolution potential on …
Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell,
2011
Chongqing Automobile college, Chongqing University of Technology,Chongqing, 400054,China;
Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell, Qiu-Hong Jia, Ming Han, Bin Deng, Cai-Zhi Zhang
Journal of Electrochemistry
In this paper, a dynamic model of PEMFC is developed to estimate the dynamic performance of PEMFC by analyzing in detail the influence factors of voltage of PEMFC including various losses. The partial pressure of hydrogen and oxygen is obtained using the differential form of the ideal-gas equation in this model. The steady-state model is obtained by setting reasonable parameter values. The simulation results and experimental results have good consistency, which shows that the simulation model is correct, reasonable and effective. It analyzed the dynamic response characteristics of the output voltage and the partial pressure of hydrogen in condition of …
Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure,
2011
College of Petrochemical Technology, Lanzhou University of Technology, Lanzhou 730050, China
Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure, Hui Xu, Zhen-Jun Peng, Dong-Hong Guo, Jun-Ling Li
Journal of Electrochemistry
The mesh-like structure of NiO electrode was obtained by first preparing the precursors via hydrothermal process using nickel sulfate and carbamide as reactants, sodium hexametaphosphate as a surfactant, and followed by calcination of the precursors at 400 ℃. The structure, morphology and capacitance characteristics of NiO electrode were characterized by XRD, SEM and constant current charge-discharge testing techniques. The effects of hydrothermal temperatures on the electrochemical properties of NiO electrode were investigated. The results showed that the better property of nickel oxide was obtained when the mole ratio of nickel to urea was 1:4 and the hydrothermal temperature was 140℃. …
Electrochemical Behaviors Of Hydroquinone On Polypyrrole/Stab-Nammt/Gc Electrode,
2011
Chemical Synthesis and Pollution Control Key Laboratory of Sichuan Province.School of Chemistry and Chemical Industry, China West Normal University. Nanchong 637002,Sichuan, China
Electrochemical Behaviors Of Hydroquinone On Polypyrrole/Stab-Nammt/Gc Electrode, Rong Li, Jian Xiong, Wei-Qiong Zhu, Yuan-Yuan Han, Jin Xu, Xiao-Ying He
Journal of Electrochemistry
The PPy/STAB-MMT/GC electrode was made using montmorillonite modified by STAB and polypyrrole (PPy). The electrochemical behaviors of hydroquinone on the PPy/STAB-MMT/GC electrode were researched by cyclic voltammetry and square wave stripping voltammetry (SWSV). The results showed that the electrode reaction occurred on the hydroquinone electrode was controlled by diffusion in PBS (pH=6.0). The number of electron transfer was equal to the number of protons (n=m=1) with the effective area of PPy/STAB-MMT/GC electrode Aeff=0.031 cm2. Under the optimized conditions, the linear response of peak current in SWSV with the concentration of hydroquinone in a range of 8.0×10-6~8.0×10 …
Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2O2 On Gew11Co/P-Opd/Gc Electrode,
2011
Institute of Environmental and Analytical Sciences, College of Chemistry and Chemical Engineering, Henan liniversity, Kaifeng 475004, Henan, China
Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2O2 On Gew11Co/P-Opd/Gc Electrode, Li-Li Zhu, Jian-Ying Qu, Jue Wang, Hao-Yue Feng
Journal of Electrochemistry
The electrochemical properties of Co-substituted trimeric tungstogermanate containing Keggin fragments were studied. Cyclic voltammograms revealed two couples of reversible redox peaks on glassy carbon (GC) electrode in acid solutions. They corresponded to two-electron reductions accompanying by the additions of four protons and three protons, respectively, both were controlled by adsorption. The differences in the peak potentials of 2-electron-4-proton and 2-electron-3-proton reactions were 31 mV and 35 mV, respectively..Furthermore, the tungstogermanate (GeW11Co) modified GC electrode with functionalization by poly(o-phenylenediamine) (P-oPD) was prepared readily by electropolymerization. The GeW11Co/P-oPD/GC electrode could electrocatalyze the reduction of hydrogen peroxide, which showed good stability and quick …
Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries,
2011
Chemistry Department, College of Chemistry and Chemical Engineering, State Key Laboratory of Physical Chemistry of Solid Surfaces, Xiamen University, Xiamen 361005, Fujan, Chin
Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong
Journal of Electrochemistry
In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …
A Brief Review Of Research Progress In The Development Of Engineering Models For Lithium Ion Batteries,
2011
1. State Key Laboratory of Physical Chemistry of Solid Surface , Department of Chemistry, College of Chemistry and Chemical Engineering, Xiamen University; 2. School of Energy Research.Xiamen University; 3. Department of Chemical Engineering, College of Chemistry and Chemical Engineering,Xiamen University, Xiamen 361005,Fujian, China
A Brief Review Of Research Progress In The Development Of Engineering Models For Lithium Ion Batteries, Da-Wei Wang, Dong-Jiang Li, Jun Li, Yong Yang
Journal of Electrochemistry
Lithium ion battery has become an important and popular electrochemical device for energy storage.Suitable evaluation and understanding of electrochemical performance and state of charge play a key role in the applications of lithium ion batteries.Construction and utilization of engineering modeling for lithium ion batteries is an effective way to fulfill this target.In this paper,engineering models of lithium ion batteries based on electrochemical reaction,ionic diffusion and migration are introduced.The emphasis is placed on the development of engineering models by the introduction of side reaction,phase transition,stress and energy.The applications of engineering models in such simulations as charge-discharge,concentration distribution,current distribution,state of charge,stress and …
Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System,
2011
Key Laboratory of Scienee & Technology of Eco-Textile, Ministry of Education, Donghua Unversity, Shanghai 201620, China
Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System, Qing-Zhi Wang, Wei Wang
Journal of Electrochemistry
The electrochemical behavior and possible reaction mechanism in Fe(Ⅲ)-oxalate-calcium gluconate system were studied by cyclic voltammetry. The results showed that Fe(Ⅱ)-gluconate was the final reductant. The reduction time, the working voltage and the cathode area influenced the current efficiency. The high current efficiency of 89% for the indirect electrochemical reduction of Vat Scarlet R could be achieved with reduction time of 10 min, working voltage of 4 V and cathode area of 40 cm2 in Fe(Ⅲ)-oxalate-calcium gluconate system.
Molecular Diffusion And Slip Boundary Conditions At Smooth Surfaces With Periodic And Random Nanoscale Textures,
2011
Wright State University - Main Campus
Molecular Diffusion And Slip Boundary Conditions At Smooth Surfaces With Periodic And Random Nanoscale Textures, Nikolai V. Priezjev
Mechanical and Materials Engineering Faculty Publications
The influence of periodic and random surface textures on the flow structure and effective slip length in Newtonian fluids is investigated by molecular dynamics (MD) simulations. We consider a situation where the typical pattern size is smaller than the channel height and the local boundary conditions at wetting and nonwetting regions are characterized by finite slip lengths. In case of anisotropic patterns, transverse flow profiles are reported for flows over alternating stripes of different wettability when the shear flow direction is misaligned with respect to the stripe orientation. The angular dependence of the effective slip length obtained from MD simulations …
Thermodynamic Limit To Photonic-Plasmonic Light-Trapping In Thin Films On Metals,
2011
Syracuse University
Thermodynamic Limit To Photonic-Plasmonic Light-Trapping In Thin Films On Metals, Eric A. Schiff
Physics - All Scholarship
We calculate the maximum optical absorptance enhancements in thin semiconductor films on metals due to structures that diffuse light and couple it to surface plasmon polaritons. The calculations can be used to estimate plasmonic effects on light-trapping in solar cells. The calculations are based on the statistical distribution of energy in the electromagnetic modes of the structure, which include surface plasmon polariton modes at the metal interface as well as the trapped waveguide modes in the film. The enhancement has the form 4n2+nλ/h (n – film refractive index, λ – optical wavelength, h …
Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites,
2011
Departemen Metalurgi dan Material, Fakultas Teknik, Universitas Indonesia, Depok 16424, Indonesia
Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam
Makara Journal of Technology
Effect of Copper Addition on Mechanical Properties and Electrical Conductivity of PP/C-Cu Bipolar Plate Composites. Bipolar plate is a major component in PEM fuel cell which possess main function of collecting and removing electrons from anode to cathode. Therefore, materials for bipolar plates produced must have high electrical conductivity. To obtain bipolar plate materials which is cheap, lightweight and high conductivity, so it is developed bipolar plates material based on PP/C-Cu composite. PP/C-Cu composites has been made by mixing all materials then compounding, rheomix, hot blending and hot press. Cu (Copper) has been used various from 0.1 wt%, 1 wt% …
Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura,
2011
Department of Aquatic Resource Management, Faculty of Science and Technology, Halmahera University, Tobelo 97762, Indonesia
Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura, Darius Arkwright, Suntoyo Suntoyo
Makara Journal of Technology
Bangkalan’s shoreline, especially on the opposite side of Surabaya, has been evaluated to determine the morphological changes due to wave attack, near-shore current, long-shore sediment transport and coastal configuration. This research aims to determine the dominant patterns of variation of Bangkalan’s shoreline change, expressed by Eigen-function in empirical orthogonal function (EOF) models. That was started with data collection such as oceanographic data (wave and tidal), bathymetry and topographic map and sediment data. All data was used for forecasting two-monthly shoreline. Coordinate of two-monthly shoreline was used as input of EOF model. The first Eigen mode is a profile of shoreline …
The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment,
2011
Faculty of Science and Mathematics, Satya Wacana Christian University, Salatiga 50711, Indonesia
The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment, Augustinus Ignatius Kristijanto, Widhi Handayani, Purwanti Asih Anna Levi
Makara Journal of Technology
Batik is one of popular arts of Indonesia. The batik industries in Sragen, Central Java, are prepared to compete in global market. In order to realize that objective, batik products should fulfill some qualifications, one of which is “environmental friendliness”. As batik production is usually generating wastewater which pollutes the environment, the technology of wastewater treatment should be developed to solve the problem. This preliminary study has been done to assess the effectiveness of anaerobic baffled reactor (ABR) and rotating biological contactor (RBC) in batik wastewater treatment. In 40 days of treatment period, the ABR performance in reducing pollutants showed …
Physical Characterization And Desulfurization Of Biobriquette Using Calcium-Based Adsorbent,
2011
Department of Chemical Engineering, Faculty of Engineering, University of Syiah Kuala, Banda Aceh 23111, Indonesia
Physical Characterization And Desulfurization Of Biobriquette Using Calcium-Based Adsorbent, Mahidin Mahidin, Asri Gani, Khairil Khairil
Makara Journal of Technology
Combustion of coal and co-combustion of their co-fuel contribute to gas emissions. Among the gas emissions are SOx, NOx, CO and CO2. Introduction of calcium based adsorbent is addressed to absorb SO2 that release to the atmosphere during the combustion process. Objective of the research is at first to observe the physical characteristics of biobriquettes as a function of briquette compositions (coal to palm kernel shell ratios) and Ca/S ratios (Ca in adsorbent and S in briquette) using a natural adsorbent (shellfish waste). The second objective is to investigate desulfurization characteristics as a function of Ca/S ratios and desulfurization temperatures …
Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill,
2011
Departemen Kehutanan, Fakultas Pertanian, Universitas Sumatera Utara, Medan 20155, Indonesia
Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara
Makara Journal of Technology
Medium Density Fibreboard Made of Acetylated Sludge from Paper Mill. Research of using sludge as raw material for making medium density fibreboard (MDF) was useful to create additional value of sludge. The objective of the research was to evaluate physical properties, mechanical properties, and durability of MDF from acetylated sludge in 4 levels of acetate anhydride (0%, 3%, 5%, and 7%) with 3 replicates. The MDF was made using dry process. After materials were mixed with adhesives, they were pressed using hotpress under 170 oC temperature and 45 Pa pressure for 25 minutes. The size of the MDF sample was …
Cassava Pulp As A Biofuel Feedstock Of An Enzymatic Hydrolysis Proces,
2011
Department of Chemical Engineering, Faculty of Industrial Technology, Institut Teknologi Sepuluh Nopember, Surabaya 60111, Indonesia
Cassava Pulp As A Biofuel Feedstock Of An Enzymatic Hydrolysis Proces, Djuma’Ali Djuma’Ali, Nonot Soewarno, Sumarno Sumarno, Dyah Primarini, Wahono Sumaryono
Makara Journal of Technology
Cassava pulp, a low cost solid byproduct of cassava starch industry, has been proposed as a high potential ethanolic fermentation substrate due to its high residual starch level, low ash content and small particle size of the lignocellulosic fibers. As the economic feasibility depends on complete degradation of the polysaccharides to fermentable glucose, the comparative hydrolytic potential of cassava pulp by six commercial enzymes were studied. Raw cassava pulp (12% w/v, particle sizeμm) hydrolyzed by both commercial pectinolytic (1) and amylolytic (2) enzymes cocktail, yielded 70.06% DE. Hydrothermal treatment of cassava pulp enhanced its susceptibility to enzymatic cleavageas compared to …
Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences,
2011
Department of Electrical Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424, Indonesia
Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences, Dodi Sudiana, Mia Rizkinia
Makara Journal of Technology
Flood that occurred in Jakarta is not only influenced by rainfall, urban planning system and drainage alone, but also may be involved land subsidence (LS). LS is possible in because Jakarta stands on top of layers of sediments and the presence of ground water consumption in very large quantities. In this research, the Advanced Land Observing Satellite (ALOS)/Phased Array type L-band Synthetic Aperture Radar (PALSAR) data was processed to determine the level of LS in Jakarta area and its relation to flood potential area. Differential interferometry method (DInSAR) was performed on two PALSAR data with different acquisition years, i.e. 2007 …
