Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

16,808 Full-Text Articles 33,201 Authors 8,321,852 Downloads 190 Institutions

All Articles in Materials Science and Engineering

Faceted Search

16,808 full-text articles. Page 614 of 616.

Structural Characterization Of Sputter-Deposited Ss304+Xal (X = 0, 4, 7 And 10 Wt.%) Coatings And Mechanically Milled Ti, Zr And, Uma Maheswara Seelam 2010 University of Central Florida

Structural Characterization Of Sputter-Deposited Ss304+Xal (X = 0, 4, 7 And 10 Wt.%) Coatings And Mechanically Milled Ti, Zr And, Uma Maheswara Seelam

Electronic Theses and Dissertations

Study of the metastable phases obtained by non-equilibrium processing techniques has come a long way during the past five decades. New metastable phases have often given new perspectives to the research on synthesis of novel materials systems. Metastable materials produced by two non-equilibrium processing methods were studied for this dissertation- 304-type austenitic stainless steel (SS304 or Fe-18Cr-8Ni)+aluminum coatings produced by plasma enhanced magnetron sputter-deposition (PEMS) and nanocrystalline Ti, Zr and Hf powders processed by mechanical milling (MM). The objective of the study was to understand the crystallographic and microstructural aspects of these materials. Four SS304+Al coatings with a nominal Al …


Microstructural Investigation Of Precipitation Hardened Cuni2s+Zr Alloys For Rotor Applications, Jean-Paul Vega-Garcia 2010 University of Central Florida

Microstructural Investigation Of Precipitation Hardened Cuni2s+Zr Alloys For Rotor Applications, Jean-Paul Vega-Garcia

Electronic Theses and Dissertations

Industrial generator components experience high stresses and electrical fields during their service life. Material integrity is key in guaranteeing component performance. CuNi2SiZr, used as rotor wedges in generators, serve to maintain rotor slot content in place while experiencing high centrifugal stresses and low cycle fatigue during start and stop at elevated temperature. The quality and integrity of this material in service can be directly related to its microstructure, which is determined by the processing procedures of the wedges. In this study, the microstructure development in this material is evaluated to eliminate grain boundary defects by optimizing processing parameters, determining the …


Investigation Of Thermal, Elastic And Load-Biased Transformation Strains In Niti Shape Memory Alloys, Shipeng Qiu 2010 University of Central Florida

Investigation Of Thermal, Elastic And Load-Biased Transformation Strains In Niti Shape Memory Alloys, Shipeng Qiu

Electronic Theses and Dissertations

Polycrystalline NiTi shape memory alloys have the ability to recover their original, pre-deformed shape in the presence of external loads when heated through a solid-solid phase transformation from a lower-symmetry B19' martensite phase to a higher-symmetry B2 austenite phase. The strain associated with a shape memory alloy in an actuator application typically has thermal, elastic and inelastic contributions. The objective of this work was to investigate the aforementioned strains by recourse to in situ neutron diffraction experiments during selected combinations of heating, cooling and/or mechanical loading. The primary studies were conducted on polycrystalline Ni49.9Ti50.1 specimens on the Spectrometer for MAterials …


Strengthening Potential Of Single-Walled Carbon Nanotubes In Phenolic Resin Composites, Brittany Kerr 2010 University of Central Florida

Strengthening Potential Of Single-Walled Carbon Nanotubes In Phenolic Resin Composites, Brittany Kerr

Electronic Theses and Dissertations

Strengthening potential of single-walled carbon nanotubes (SWCNTs) in a phenolic resin composite was evaluated by characterization of purified and phenyl sulfonated SWCNTs, investigation of the load transfer capability of the purified SWCNTs, and characterization of the composites. Purified and phenyl sulfonated SWCNTs, as well as their composites, were examined by Raman spectroscopy, thermogravimetric analysis, scanning electron microscopy equipped with energy dispersive spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and ultra violet-visible spectrometry. Fabrication of the SWCNT/phenolic resin composite was performed by first dispersing the SWCNTs in ethylene glycol and then homogenizing the mixture with phenolic resin. The ethylene glycol was …


Synthesis And Characterization Of A [Ru(Bpy)2(Ncs)2] Derivative For Use As A Dye-Sensitizer In Nanocrystalline Solar Cells, Joel Thomas Kirner 2010 University of Northern Iowa

Synthesis And Characterization Of A [Ru(Bpy)2(Ncs)2] Derivative For Use As A Dye-Sensitizer In Nanocrystalline Solar Cells, Joel Thomas Kirner

Honors Program Theses

After extensive review of the field of dye-sensitized solar cells, the molecule [Ru(4,4’- dicarboxy-2,2’-bipyridine)(4,4’-di-(2-(2-pyridyl)ethenyl)-2,2’-bipyridine)(NCS)2] has been designed as an original contribution to the field. This dye sensitizer was chosen by derivatizing upon the structure of the standard sensitizer, cis-diisothiocyanatobis(4,4’-dicarboxylic acid-2,2’- bipyridine)ruthenium(II) (N3), by extending the conjugation of one bipyridine ligand. This structural derivatization should enhance light harvesting by red-shifting the dye’s absorbance and increasing the dye’s molar absorptivity, which should result in a dye-sensitized solar cell with higher efficiency. The Density Functional Theory (DFT) molecular orbital calculations of the new dye complex indicate that the HOMO is highly localized …


Synthesis And Characterization Of Ferromagnetic Nanowires, PoChing Tsai 2010 University of Texas at Arlington

Synthesis And Characterization Of Ferromagnetic Nanowires, Poching Tsai

Material Science and Engineering Theses - Archive

Ferromagnetic nanocrystals with shape anisotropy have drawn great attention in the past decades because of their unique magnetic properties and for their potential applications in ultra-high-density magnetic recording media, exchange-coupled nanocomposite magnets and related nanodevices. In this thesis, synthesis and characterixation of ferromagnetic CoNi and CoFe nanowires are reported. CoNi nanocrystals with different size, shape and composition were successfully synthesized via a catalyst chemical solution method. It was found out that the structure and morphology can be controlled by altering the NaOH concentration, and the elongation of the nanowires can be adjusted by changing surfactants ratio and catalyst amount. Unlike …


Solid-State Tunneling Spectroscopy Of Individual Quantum Dots, Ramkumar Subramanian 2010 University of Texas at Arlington

Solid-State Tunneling Spectroscopy Of Individual Quantum Dots, Ramkumar Subramanian

Material Science and Engineering Dissertations - Archive

Quantum dots are gaining importance for their potential applications in the fields of energy harvesting, bio-labeling and treatment, in opto-electronic devices and in photonic devices. For all these applications, it is imperative to know their electronic structure. Although currently several spectroscopic techniques exist to study the electronic structure of these quantum dots, they are accompanied by other effects and do not give purely the electronic structure of the individual quantum dot. The main goals of this research are to:o To study the energy level structure of `single' quantum dots.o Develop a new spectroscopic technique that allows the measurement of the …


Transmission Electron Microscopy Studies Of Lamno₃ And La₁₋Xsrxmno₃Thin Films Grown On Various Substrates, Yinsheng Fang 2010 University of Texas at Arlington

Transmission Electron Microscopy Studies Of Lamno₃ And La₁₋Xsrxmno₃Thin Films Grown On Various Substrates, Yinsheng Fang

Material Science and Engineering Theses - Archive

LaMnO₃ (LMO) and La₁₋xSrxMnO₃ (LSMO) thin films with colossal magnetoresistance have attracted considerable interest for potential applications in many technological devices, such as magnetic sensors and read-head of computer memory. In this work, polycrystalline and epitaxial LMO and LSMO thin films were deposited on various substrates including (001) Si, (001) MgO, and (001) LaAlO₃ (LAO) using RF magnetron sputtering. The microstructures of the thin films were initially studied using X-ray diffraction. Detailed microstructure information such as crystallite of the films, grain size, epitaxial quality, crystallographic structure and film/substrate interface were studied using high-resolution transmission electron microscope (HRTEM). More specifically, Effects …


Giant Raman Enhancement On Nanoporous Gold Film By Conjugating With Nanoparticles For Single-Molecule Detection, Lihua Qian, Biswajit Das, Yan Li, Zhilin Yang 2010 University of Nevada, Las Vegas

Giant Raman Enhancement On Nanoporous Gold Film By Conjugating With Nanoparticles For Single-Molecule Detection, Lihua Qian, Biswajit Das, Yan Li, Zhilin Yang

Electrical & Computer Engineering Faculty Research

Hot spots have the contradictively geometrical requirements for both the narrowest interstices to provide strong near-field coupling, and sufficient space to allow entrance of the analytes. Herein, a two-step method is employed to create hot spots within hybrid nanostructures, which consist of self-supported nanoporous gold films with the absorbed probes and subsequent nanoparticle conjugates without surface agents or mechanical motion. The molecules confined into 1 nm interstice exhibit 2.9 × 107 times enhancement in Raman scattering compared to pure nanoporous gold. Giant enhancement primarily results from strong near-field coupling between nanopore and nanoparticle, which is theoretically confirmed by finite-difference …


Mse News 2010, Department of Materials Science and Engineering, Michigan Technological University 2010 Michigan Technological University

Mse News 2010, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

  • MSE Welcomes New Professors
  • Professor Emeritus Passes
  • Alumni Achieves Milestone
  • Hydrogen Storage Research
  • Student Accomplishments
  • Staff News
  • Alumni News


Electrical And Structural Studies Of Polyacrylonitrile (Pan) Complexed With Inorganic Salts., Khairul Bahiyah Md Isa 2010 Universiti Malaya

Electrical And Structural Studies Of Polyacrylonitrile (Pan) Complexed With Inorganic Salts., Khairul Bahiyah Md Isa

Student Works (2010-2019)

In the present study, polymer electrolyte films composed of polyacrylonitrile (PAN) as a host polymer, ethylene carbonate (EC) as the plasticizer and lithium triflate (LiCF3SO3) and sodium triflate (NaCF3SO3) as dopant salts were prepared by the solution cast technique. Five systems of polymer electrolytes films have been prepared; these systems are the plasticized-PAN system i.e. PAN-EC system, two salted-PAN systems i.e. PAN-LiCF3SO3 and PAN-NaCF3SO3, and two plasticized-salted PAN systems i.e. PAN-EC-LiCF3SO3 and PAN-EC-NaCF3SO3. The pure PAN film was prepared as a reference. The ionic conductivity for each system is characterized using impedance spectroscopy. The room temperature conductivity of the pure …


Band Structure Of Fe Based Superconductors., Teh Yee Lin 2010 Universiti Malaya

Band Structure Of Fe Based Superconductors., Teh Yee Lin

Student Works (2010-2019)

Several iron containing superconductors are discovered in 2008. The discovery introduced a new class of high-temperature superconductors, which are iron-based. The iron-based superconductors do not resemble conventional superconductors and have properties on their own which differ from the cuprates. We have studied the iron selenium, FeSe compound by removing some Se atoms from the lattice forming Fe:Se = 2:1 and 8:6 and also by replacing the Se vacancy with tellurium, samarium and oxygen atoms forming Fe:Se:Te = 2:1:1 and 8:6:2, Fe:Se:O = 8:6:2 and 8:4:2, FeSeSmO, FeSeTeO, Fe2SeSm2O2, FeSeTeSmO and FeTeSmO. The band structures for each lattice are calculated by …


Synthesis And Characterization Of Silicon Oxide And Silicon Carbide Nanostructures., Majid Salim Mohammed Al-Ruqieshi 2010 Universiti Malaya

Synthesis And Characterization Of Silicon Oxide And Silicon Carbide Nanostructures., Majid Salim Mohammed Al-Ruqieshi

Student Works (2010-2019)

Silicon oxide nanostructures have attracted extensive interests in recent years due to their physical and optical properties. SiOx nanostructures are synthesized by catalytic and non-catalytic approaches. With catalytic approach, long and uniform amorphous silicon oxide nanowires, nanofibers (comet and tree like), nanocakes and nanocages were synthesized on Si substrate by carbothermal evaporation reactions of TiO2 at high temperature. The SiOx nanowires were about 13 nm to 243 nm in diameters and 194 nm to several microns in length and the nanofibres with diameter between 8 nm to 30 nm and around 50 nm to 2.5μm in length. The diameter and …


Electrodeposition Of Tin Using Tin(Ii) Methanesulfonate From Mixture Of Ionic Liquid And Methane Sulfonic Acid., Yang Kok Kee 2010 Universiti Malaya

Electrodeposition Of Tin Using Tin(Ii) Methanesulfonate From Mixture Of Ionic Liquid And Methane Sulfonic Acid., Yang Kok Kee

Student Works (2010-2019)

The electrodeposition of tin from Tin(II) Methane Sulfonate (MSA) with varying concentration in air and water stable 1-butyl-1-methyl-pyrrolidinium trifluoromethanesulfonate, (BMPOTF) ionic liquid at room temperature was studied. Cyclic Voltammetry served to characterize the electrochemical behavior of tin reduction and oxidation. The diffusion coefficient of stannous ions in the mixture of BMPOTF ionic liquid and MSA based electrolyte obtained via Randles-Sevcik and Cottrell equation was 2 × 10-7 cm2/s. Electroplating on copper panel was conducted under different current densities to determine BMPOTF based tin plating solution current efficiency. Mixture of BMPOTF and MSA based tin plating solution gave current efficiency as …


Strain-Stiffening In Synthetic And Biopolymer Networks, Kendra Erk, Kevin J. Henderson, Kenneth R. Shull 2010 Purdue University

Strain-Stiffening In Synthetic And Biopolymer Networks, Kendra Erk, Kevin J. Henderson, Kenneth R. Shull

School of Materials Engineering Faculty Publications

Strain-stiffening behavior common to biopolymer networks is difficult to reproduce in synthetic networks. Physically associating synthetic polymer networks can be an exception to this rule and can demonstrate strain-stiffening behavior at relatively low values of strain. Here, the stiffening behavior of model elastic networks of physically associating triblock copolymers is characterized by shear rheometry. Experiments demonstrate a clear correlation between network structure and strain-stiffening behavior. Stiffening is accurately captured by a constitutive model with a single fitting parameter related to the midblock length. The same model is also effective for describing the stiffening of actin, collagen, and other biopolymer networks. …


Electrochemical Characterization Of Cerium-Based Conversion Coatings On Al 7075-T6, Simon Joshi 2010 Missouri University of Science and Technology

Electrochemical Characterization Of Cerium-Based Conversion Coatings On Al 7075-T6, Simon Joshi

Doctoral Dissertations

"This research used electrochemical techniques to characterize the deposition and corrosion protection behavior of cerium-based conversion coatings on AI 7075-T6. Alkaline activation decreased native oxide impedance (5.9 kΩ-cm²) by ~25% promoting deposition of 250-500 mn coatings. Activation in NaOH solutions deposited coatings with large cracks and craters, whereas Na₂C0₃ activation resulted in uniform coatings, i.e., fewer cracks and almost no craters. Uniformly deposited coatings exhibited better cathodic inhibition and higher impedance (~200 kΩ-cm²) than on NaOH activated substrates (~100 kΩ-cm²). Subsurface crevices, caused by Cl⁻ and H₂O₂ in the deposition solution, were found under large cracks and craters. Thus, Na₂CO₃ …


Localized Mechanical Deformation And Dissolution Of 45s5 Bioglass, Ding Li 2010 University of Kentucky

Localized Mechanical Deformation And Dissolution Of 45s5 Bioglass, Ding Li

University of Kentucky Doctoral Dissertations

Bioactive glasses react with the human physiological solution in control of their biofunctionality. The stress state in bioactive glasses determines the chemomechanical reaction and their biofunctionality. Using the microindentation technique, the effect of the indentation deformation on the surface damage and material dissolution of 45S5 bioglass was investigated.

The indentation-induced residual stresses were calculated. Complete anelastic recoveries of the indentation depths and the impression marks were observed for the first time, which was likely driven by the stored strain energy over the anelastic deformation zone. The indentation-induced local surface damages were revealed before and after the immersion tests in phosphate …


Experimental Study On Thermal Treatment Of Used Printed Wiring Boards (Pwbs), Xiangjun Zuo 2010 Missouri University of Science and Technology

Experimental Study On Thermal Treatment Of Used Printed Wiring Boards (Pwbs), Xiangjun Zuo

Masters Theses

The availability of cheaper and better electronic products as a result of the rapid innovation in technology in past decades has driven the production of e-waste forward. Printed wiring board (PWB) is a component made of one or more layers of insulating material with electrical conductors. The existing processes of recycling PWBs use pyrometallurgical or hydrometallurgical methods, which generate atmospheric pollution. Green recycling has obvious benefits to decrease the amount of PWBs. Green recycling includes two features, 1) little or zero pollution of toxic gases and heavy metals, and 2) efficient (quick and economical) recycling.

The aim of this work …


Phosphate Post-Treatment Of Cerium-Based Conversion Coatings On Al 2024-T3, Daimon K. Heller 2010 Missouri University of Science and Technology

Phosphate Post-Treatment Of Cerium-Based Conversion Coatings On Al 2024-T3, Daimon K. Heller

Doctoral Dissertations

"Phosphate post-treatment of cerium-based conversion coatings (CeCCs) on high strength aluminum alloys can significantly improve corrosion resistance. As-deposited CeCCs exhibit corrosion pits and salt tails across the specimen surface after 3 days of exposure, but post-treated CeCCs have withstood 14 days of salt spray exposure without visibly corroding. The morphology, phase, and electrochemical properties of spray deposited CeCCs were affected by post-treatment parameters such as immersion time, solution temperature, and phosphate source. The best performing coatings were post-treated in aqueous orthophosphate solutions for at least 5 min at temperatures of at least 85⁰C. These conditions converted cerium hydroxy/peroxy species in …


Impedance Spectroscopy Of Batio₃ Cubes Suspended In Lossy Liquids As A Physical Model Of Two-Phase System, Piotr Z. Jasinski, Vladimir Petrovsky, Fatih Dogan 2010 Missouri University of Science and Technology

Impedance Spectroscopy Of Batio₃ Cubes Suspended In Lossy Liquids As A Physical Model Of Two-Phase System, Piotr Z. Jasinski, Vladimir Petrovsky, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Impedance spectroscopy techniques were used for analysis of the physical model in a two-phase system toward determining of dielectric constant of dielectric particles suspended in liquids at various solids loading (volume fraction) levels. Model experimental studies were conducted using BaTiO3 as a dielectric material that was prepared as small cubes of uniform size (2×2×1 mm). Barium titanate (BT) cubes having a dielectric constant of 3850 were immersed in liquids of low dielectric constant and moderate electrical conductivity. Measured impedance spectra consisted of two semicircles, which were fitted for (R∥C)(R∥C) equivalent circuit. The parameters obtained from fitting were compared with the …


Digital Commons powered by bepress