Materials Science and Engineering Commons^™

An Overview Of The Development Of Cement-Based Batteries For The Cathodic Protection Of Embedded Steel In Concrete, Aimee Byrne, Niall Holmes, Brian Norton

Conference papers

This paper presents an overview of the cement-based batteries developed in DIT for use in the cathodic protection of embedded steel in reinforced concrete undergoing chloride-induced corrosion. Cathodic protection delivers an external current (approximately 20mA per m2 of embedded steel) which effectively polarises the internal current generated during corrosion. The batteries developed in DIT comprise of a cement-based electrolyte containing different additives including sand, aggregate, salts, carbon black and plasticiser with protruding anode and cathode metal plates. These batteries produced an initial electrical output of 1.5V and 23mA through a 10 resistor as measured using data acquisition units and a …

Complex Capillary Fluidic Phenomena For Passive Control Of Liquids In Low-Gravity Environments, Logan Torres

Maseeh Summer Undergraduate Research Experience

In an effort to further apply the recent results of puddle jumping research, we seek to expand the oblique droplet impact studies of others by exploiting large liquid droplets in the near weightless environment of a drop tower. By using the spontaneous puddle jump mechanism, droplets of volumes 1 mL ≤ V ≤ 3 mL with corresponding Weber numbers of We ≈ 1 are impinged on surfaces inclined in the range 40° ≤ α ≤ 80° (measured from the horizontal plane). Impact surface wetting characteristics exhibit static contact angles θstatic = 165 ± 5°. All impacts result in complete rebound. …

Engineered Mushing Cooker, Aimee Ritter

Maseeh Summer Undergraduate Research Experience

This project revolves around building methanol cookers for dog mushers in the Iditarod and for the Denali Park Ranger Kennel in Denali National Park, Alaska. Traditional cookers are bulky, slow to burn, and use up a lot of fuel. Our goal has been to revolutionize the way mushing cookers look and perform. Our cookers are built to pack well in the sleds, heat up to 3 gallons of snowmelt, perform in arctic climates, use methanol (specifically HEET) for fuel, and be lightweight. A traditional cooker would use 3 to 4 bottles or more of HEET (36-48+oz.) and take at least …

Design For Fractal Grid Generated Turbulence, Moira Gion

Maseeh Summer Undergraduate Research Experience

Fractal geometry can be used to find organization or order in something that appears to be in disorder, or chaos. Turbulence is viewed as one place where fractal geometry can be found in nature. The irregularity in fluid flow is dependent on the initial conditions. In the past, the idea of self-similarity has been used to develop statistical theories of energy cascade in a turbulent flow. Recent studies have done experiments on obstructing flows with fractal objects to observe intermittency, (or self-similarity) within a turbulent flow. Experiments on fractal grid generated turbulence has been performed by other research groups, so …

Investigation Of The Resistance To Demagnetization In Bulk Rare-Earth Magnets Comprised Of Crystallographically-Aligned, Single-Domain Crystallites With Modified Intergranular Phase, Jie Li

Dissertations, Master's Theses and Master's Reports

The research presented in this dissertation investigates whether an increased coercivity of Neodymium-Iron-Boron (Nd2Fe14B) based bulk magnets at elevated temperature (160°C), which is now only obtainable by substituting ~7wt% dysprosium (Dy) for a portion of neodymium (Nd), can be achieved through specific microstructural modifications with decreased Dy concentrations. The approach is to reduce the size of individual crystallographically-aligned grains in the magnet so that each grain can only support a single magnetic domain and to simultaneously dilute the Nd-Fe inter-granular phase present in conventional magnets with a non-Fe-containing, Nd-rich phase (Nd-Cu alloy) in an attempt to partially magnetically isolate the …

Inhibition Of Bacterial Growth And Prevention Of Bacterial Adhesion With Localized Nitric Oxide Delivery, Julia Osborne

Dissertations, Master's Theses and Master's Reports

Bacterial infections continue to be a problem at the site of an indwelling medical device, and over the years, various bacterial strains have become more resistant to current antibiotic treatments. Bacterial infection at an indwelling medical device can be dangerous and affect the performance of the medical device which can ultimately lead to the failure of the device due to bacterial resistance to treatment.

Nitric Oxide (NO) has been shown to possess antibacterial properties to prevent and inhibit bacterial growth. NO releasing coatings on indwelling medical devices could provide a reduction in bacterial infections that occur at the device site …

The Effect Of Solidification Rate And Solutionizing Quench Rate On The Mechanical Properties And Hardening Response Of Aluminum Alloys: A Quantitative Comparison, Rafael Gil-Figueroa

Dissertations, Master's Theses and Master's Reports

A comparative study of five aluminum alloys was performed to characterize the effect of solidification rate and quench rate on casting microstructure and properties. The alloys were cast in the geometry for Jominy End Quench (JEQ) testing, so as to take advantage of the JEQ test’s ability to give data on multiple quench rates in a single sample and illustrate the quench sensitivity of an alloy. While the Jominy End Quench test has been used in aluminum alloys, the effects of solidification rates have not been assessed in depth. The work done by other studies has either focused on a …

The Metal/Organic Interface In Cobalt/Vinylidene Fluoride Heterostructures, Keith Foreman, E Echeverria, Mark A. Koten, R. M. Lindsay, N. Hong, Jeffrey E. Shield, Shireen Adenwalla

Shireen Adenwalla Papers

Organic-based electronic devices are rapidly increasing in popularity, making it essential to understand and characterize the interface between organic materials and metallic electrodes. This work reports on the characterization of the interface between thin films of an emerging organic ferroelectric, vinylidene fluoride (VDF) oligomer, and Co, an important high Curie temperature ferromagnet. Using a wide battery of experimental techniques, it is shown that VDF oligomer thin films as thin as 15 nm can halt, or prevent, Co oxidization in atmospheric conditions, a necessary condition for device applications. Selectivity of magnetic properties, such as remanent magnetization, is enabled by the clarification …

Ferroelectric Characterization And Growth Optimization Of Thermally Evaporated Vinylidene Fluoride Thin Films, Keith Foreman, N. Hong, C. Labedz, C. Shearer, Stephen Ducharme, Shireen Adenwalla

Shireen Adenwalla Papers

Organic thin films have numerous advantages over inorganics in device processing and price. The large polarization of the organic ferroelectric oligomer vinylidene fluoride (VDF) could prove useful for both device applications and the investigation of fundamental physical phenomena. A VDF oligomer thin film vacuum deposition process, such as thermal evaporation, preserves film and interface cleanliness, but is challenging, with successful deposition occurring only within a narrow parameter space. We report on the optimal deposition parameters for VDF oligomer thin films, refining the parameter space for successful deposition, resulting in a high yield of robust ferroelectric films. In particular, we investigate …

Development Of Implants Composed Of Bioactive Materials For Bone Repair, Wei Xiao

Doctoral Dissertations

"The purpose of this Ph.D. research was to address the clinical need for synthetic bioactive materials to heal defects in non-loaded and loaded bone. Hollow hydroxyapatite (HA) microspheres created in a previous study were evaluated as a carrier for controlled release of bone morphogenetic protein-2 (BMP2) in bone regeneration. New bone formation in rat calvarial defects implanted with BMP2-loaded microspheres (43%) was significantly higher than microspheres without BMP2 (17%) at 6 weeks postimplantation. Then hollow HA microspheres with a carbonate-substituted composition were prepared to improve their resorption rate. Hollow HA microspheres with ~12 wt. % of carbonate showed significantly higher …

Characterization Of Tensile Deformation In Az91 Mg Alloy Castings, Ogun Unal

UNF Graduate Theses and Dissertations

Tensile deformation characteristics of cast aluminum alloys have been investigated extensively. Cast Mg alloys have remained mostly neglected by researchers, despite their potential for weight savings. This present study is motivated by this gap in the literature and consists of two stages; in Stage 1, analysis of tensile data gathered from literature were reanalyzed, and in Stage 2, data generated from tensile testing of 60 specimens of AZ91 Mg alloy castings in both T4 and T6 conditions were analyzed to characterize work hardening behavior.

In Stage 1, more than 1600 data were collected from the literature for various Mg alloy …

Geometric Deformations Of Sodalite Frameworks, Ciprian Borcea, Ileana Streinu

Computer Science: Faculty Publications

In mathematical crystallography and computational materials science, it is important to infer flexibility properties of framework materials from their geometric representation. We study combinatorial, geometric and kinematic properties for frameworks modeled on sodalite.

Synthesis Of Radioactive Nanostructures In A Research Nuclear Reactor, Maria Camila Garcia Toro

Masters Theses

In this work, the synthesis of radioactive nanostructures by water radiolysis was studied. The irradiation processes were done in the Missouri University of Science and Technology research nuclear reactor (MSTR).

Radioactive gold nanoparticles (AuNPs) were synthesized from aqueous solutions containing the metal salt precursors by radiolysis of water. Seven different samples were irradiated at 200kW of thermal power for 0.5, 1, 3, 5, 10, 30, and 60 minutes. The average sizes of the obtained nanoparticles ranged from 3 nm to 400 nm, it was found that the particle size decreased with the irradiation time. Some agglomerations of particles were found …

Real-Time Monitoring Of Personal Exposures To Carbon Dioxide, Elliott T. Gall, Toby Cheung, Irvan Luhung, Stefano Schiavon, William W. Nazaroff

Mechanical and Materials Engineering Faculty Publications and Presentations

Elevated indoor CO₂ levels are indicative of insufficient ventilation in occupied spaces and correlate with elevated concentrations of pollutants of indoor origin. Adverse health and well-being outcomes associated with elevated indoor CO₂ levels are based on CO₂ as a proxy, although some emerging evidence suggests CO₂ itself may impact human cognition. Using portable monitors, we conducted an exposure study with 16 subjects in Singapore to understand the levels, dynamics and influencing factors of personal exposure to CO₂. Participants carried a CO₂ monitor continuously for 7-day periods recording their exposure levels at 1-min intervals. …

Materials Characterization Of Deposits On Starboard (Inboard) Elevon Actuator Shaft Recovered From Space Shuttle Columbia, Mayra Contreras

Open Access Theses & Dissertations

With the new era of space exploration upon us and the Orion spacecraft currently being tested, which would replace the Space Shuttle as the orbiter that will transport humans into space once again, safety assurance is the main component for a successful mission. Aerospace materials have always played a big role when it comes to safety assurance. Having the knowledge of what materials are suitable to keep using when designing the future spacecraft that will take humans to Mars is fundamental in order to be confident that the vehicle and all that comprises it will function as envisioned. Expanding the …

A Cracking Methodology To Assess Fracture And Fatigue Properties Of Asphalt Concrete Mixtures Using Overlay Tester, Victor M. Garcia

Open Access Theses & Dissertations

Several highway agencies have either implemented or considered implementing performance tests to predict the cracking potential of asphalt concrete (AC) mixtures in the laboratory setting. One such test, the Overlay Tester (OT) test, measures the number of cycles to failure of the AC specimens by simulating the opening and closing of the cracks induced by daily temperature variations and high tensile strain generated by the traffic load. The variability of the OT test results is expressed as a major concern in reliably characterizing the cracking potential of the AC mixes.

The performance of the OT test, in general, and current …

Wettability Of Magnesium Based Alloys, Victor Manuel Ornelas

Open Access Theses & Dissertations

The premise of this project was to determine the wettability behavior of Mg-based alloys using three different liquids. Contact angle measurements were carried out along with utilizing the Zisman method for obtaining values for the critical surface tension. Adhesion energy values were also found through the use of the Young-Dupre equation. This project utilized the Mg-based alloy Mg-2Zn-2Gd with supplemented α-Minimum Essential Medium (MEM), Phosphate Buffer Saline solution (PBS), and distilled water. These three liquids are commonly used in cell cultivation and protein adsorption studies. Supplemented α-MEM consisted of α-MEM, fetal bovine serum, and penicillin-streptomycin. Mg-2Zn-2Gd was used because of …

Molecular Dynamics Proxy Applications For Optimizing Performance Of Simulations Under Extreme Conditions, Jayalath Abeywardhana Mudiyanselage Madawa Abeywardhana

Open Access Theses & Dissertations

Exascale performance of scientific application is a prominent goal for the scientific community and computer hardware vendors. As a result, several proxy applications for the widely used scientific codes have been developed with the purpose of testing performance, memory and power consumption issues associated with simulations at the exascale. Co-MD is a proxy application for classical Molecular Dynamics (MD) codes based on the (SPaSM) Los Alamos code.

This work comprises two different but related computational aspects: performance evaluation and optimization of Co-MD (Co-Design Molecular Dynamics) for different computer architectures/execution models, and direct application of SPaSM (Scalable Parallel Short-range Molecular Dynamics) …

Improving The Engineering Properties Of Pla For 3d Printing And Beyond, Carmen R. Rocha

Open Access Theses & Dissertations

Additive manufacturing (AM), now more commonly known as 3D printing, has been classified as efficient, fast, and practical in the prototyping sector of product development. In the work presented here, we will use one of the AM techniques known as Material extrusion 3D printing (ME3DP), which has all the advantages of AM. However, one of the biggest challenges facing ME3DP technologies is the limitation of the range of materials used by this technique. Acrylonitrile butadiene styrene (ABS) and poly-lactic acid (PLA) are currently the most common thermoplastics materials used in ME3DP because of their ability to melt and be reprocessed. …

Intrinsic And Metal-Doped Gallium Oxide Based High-Temperature Oxygen Sensors For Combustion Processes, Ernesto Javier Rubio

Open Access Theses & Dissertations

Currently, there is enormous interest in research, development and optimization of the combustion processes for energy harvesting. Recent statistical and economic analyses estimated that by improving the coal-based firing/combustion processes in the power plants, savings up to ~$450-500 million yearly can be achieved. Advanced sensors and controls capable of withstanding extreme environments such as high temperatures, highly corrosive atmospheres, and high pressures are critical to such efficiency enhancement and cost savings. For instance, optimization of the combustion processes in power generation systems can be achieved by sensing, monitoring and control of oxygen, which is a measure of the completeness of …