Materials Science and Engineering Commons^™

Intrinsic And Metal-Doped Gallium Oxide Based High-Temperature Oxygen Sensors For Combustion Processes, Ernesto Javier Rubio

Open Access Theses & Dissertations

Currently, there is enormous interest in research, development and optimization of the combustion processes for energy harvesting. Recent statistical and economic analyses estimated that by improving the coal-based firing/combustion processes in the power plants, savings up to ~$450-500 million yearly can be achieved. Advanced sensors and controls capable of withstanding extreme environments such as high temperatures, highly corrosive atmospheres, and high pressures are critical to such efficiency enhancement and cost savings. For instance, optimization of the combustion processes in power generation systems can be achieved by sensing, monitoring and control of oxygen, which is a measure of the completeness of …

Microstructural Investigation Of Vintage Pipeline Steels Highly Susceptible To Stress Corrosion Cracking, Monica Adriana Torres

Open Access Theses & Dissertations

The use of pipelines for the transmission of gas offers not only efficiency, but a number of economic advantages. Nevertheless, pipelines are subject to aggressive operating conditions and environments which can lead to in-service degradation [1] and thus to failures. These failures can have catastrophic consequences, such as environmental damage and loss of life [2]. One of the most dangerous threats to pipeline integrity is stress corrosion cracking (SCC). Despite the substantial progress that has been achieved in the field, due to the complex nature of this phenomenon there is still not a complete understanding of this form of external …

Influence Of The Substrate Characteristics On The Bond Behavior Of Pbo Frcm-Concrete Joints, Tommaso D'Antino, Lesley H. Sneed, Christian Carloni, Carlo Pellegrino

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Fiber Reinforced Cementitious Matrix (FRCM) composites can be employed as a valid alternative to Fiber Reinforced Polymers (FRP) composites for strengthening existing reinforced concrete (RC) structures. The weakness of FRCM-concrete joints has been reported to be at the matrix-fiber interface rather than within the concrete substrate, as is usually reported in the case of FRP-concrete joints. The experimental investigations regarding FRCM strengthening available in the literature have been performed by applying the FRCM composite onto a surface that was treated before the application, usually by grinding or sandblasting. However, the role of the substrate characteristics on the failure mechanism of …

Special Issue: Electrochemistry Of Carbon Materials, Wei Chen

Journal of Electrochemistry

Carbon materials are traditional electrode materials due to their excellent electrical conductivities, high electrochemical stabilities and wide potential windows. Glassy carbon, graphite, various activated charcoals, carbon fibers etc. have been widely used in electrochemistry serving as electrode substrates or supports. In addition to their applications in basic electrochemistry, carbon materials have also played important roles in electrochemical energy storage and conversion. In recent years, various types of carbon structures, from zero-dimensional carbon nanodots, one-dimensional nanotubes, two-dimensional graphene to three-dimensional porous carbons, have attracted increasing attention in electrochemical field. It has been found that carbon materials have outstanding properties as advanced …

Applications Of Carbon Materials In Electrochemical Energy Storage, Ji Liang, Lei Wen, Hui-Ming Cheng, Feng Li

Journal of Electrochemistry

An electrode material for electrochemical energy storage is one of the key components for high performance devices. In a variety of electrochemical energy storage systems, carbon materials, especially the lately emerged carbon nanomaterials including the carbon nanotube and graphene, have been playing a very important role and brought new vitality to the development and demonstration of the broad application prospects. In this review, we summarize the applications of various carbon materials in the typical electrochemical energy storage devices, namely lithium/sodium ion batteries, supercapacitors, and lithium-sulfur batteries, as well as flexible electrochemical energy storage and electrochemical catalysis. A perspective of novel …

Synthesis Of Porous Carbon Nanosheets And Its Application In Sodium-Ion Battery, Jing-Fei Zhang, Jing Lu, Xiao-Yu Yang, Yun-Di Huang, Lin Xu, Dong-Mei Sun, Ya-Wen Tang

Journal of Electrochemistry

Owning to sodium’s high abundance, relatively low cost, similar chemical properties to Li and very suitable redox potential of E₀(Na⁺/Na) = -2.71 V versus SHE which is only 0.3 V above that of lithium, rechargeable sodium ion battery hold much promise as potential alternatives to current lithium ion batteries for energy storage applications. Carbon material is regarded as the most promising anode candidate for sodium ion battery. Particularly, carbon nanosheet with porous structure and high conductivity is expected to have improved sodium ion storage properties. In this paper, we present a two-step pyrolysis-based method for facile …

Effect Of Mno2 Content On Electrochemical Capacitance Behavior Of Active Carbon Electrode, Kun Shen, Xian-Liang Zhou, Qi-Shun Duan

Journal of Electrochemistry

In this work, the manganese dioxide (MnO₂) materials were prepared by solution approach at low temperature, thermal decomposition and electrochemical deposition. The actived carbon (AC) and MnO₂composite electrodes were used for aqueous supercapacitors. The morphologies and structures of the prepared materials were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the electrochemical behaviors were tested by cyclic voltammetry (CV) and galanostatic charge-discharge tests. Electrochemical test data show that the maximum specific capacitances of 151, 172 and 141 F•g^-1were obtained with the contents of MnO₂being 70, 60 and 70% in …

Fast And Accurate Evaluation Of Lifepo4 Cathode Materials By Single Particle Microelectrode, Fu-Qing Wang, Yi-Min Wei, Yu-Zhuan Su, Bing-Wei Mao, Kai Wu, Feng-Gang Zhao, Chun-Lei Chen, Xing-Lu Li, Jin Chong

Journal of Electrochemistry

Single particle microelectrode enables to evaluate the electrochemical responses for single particle of active material without binder and conductive agent. Thus, the influences of additive and electrode structure on the electrochemical performance of active materials can be ignored. Furthermore, this technology can be used to evaluate active materials fast. Therefore, single particle microelectrode allows fast and accurate determination of the intrinsic performance of active material. Cyclic voltammogram (CV), cycle performance, and kinetic behavior of LiFePO₄ cathode materials were evaluated by the single particle microelectrode. CV curve of LiFePO₄ particle with a pair of oxidation and reduction peaks was …

Colloidal Ionic Supercapacitors, Kun-Feng Chen, Dong-Feng Xue

Journal of Electrochemistry

Supercapacitors have high power density and long cycle life compared with battery systems, but they still suffer from low energy density at the same time. In order to increase the energy density of supercapacitors, we have developed a new type of pseudocapacitor, called colloidal ion supercapacitor, which can directly use commercial metal salts as electrode materials and form electroactive matter by in-situ electrochemical reactions without the need of additional materials synthesis processes. Colloidal ion supercapacitor can fully utilize the redox reaction of metal cations with multiple oxidation states, which can completely release the stored electrical energy of multiple-valence cations, leading …

Progress Of Self-Supported Supercapacitor Electrode Materials Based On Carbon Substrates, Shui-Jian He, Wei Chen

Journal of Electrochemistry

Self-supported electrode materials have been widely used in supercapacitors. Carbon materials are promising substrates in building self-supported electrode materials attributed to their diverse structures, rich resource, relatively low cost and high stability. Combined with our own research in this field, we summarize here the recent progress on the synthesis of self-supported electrode materials and their supercapacitance properties. The overall synthetic strategy could be divided into two categories: “top-down” and “bottom-up”. We hope this review is helpful for the development and application of renewable sources in self-supported electrode materials.

Electrodeposition Of Lanthanum In Deep Eutectic Solvents, Li Wang, You-Jun Fan, Lu Wei, Hai-Xia Liu, Shi-Gang Sun

Journal of Electrochemistry

With the choline chloride/urea deep eutectic solvents (DESs) as the medium, the olive-like lanthanum particles with uniform shape and size were successfully prepared through a potentiostatic deposition method. The prepared samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray (EDX) spectroscopy and X-ray photoelectron spectroscopy (XPS). At the same time, the effect of deposition potential, temperature and time on the size and morphology of samples was investigated. The results demonstrated that the optimum conditions for the preparation of olive-like lanthanum particles were as follows: deposition potential of -1.7 V, temperature of 80 °C and …

Carbon Aerogel/Nickel Foam As Electrode For High-Performance Supercapacitor, Zhong Wu, Xin-Bo Zhang

Journal of Electrochemistry

Herein, a facile synthesis has been explored to prepare carbon aerogel/Ni foam. Graphene oxide, resorcinol and formaldehyde serve as precursors and polymerize in-situ on the Ni foam after hydrothermal synthesis at 85 ℃. After lyophilization treatment, the carbon aerogel/Ni foam with porous structure can be obtained. Electrochemical investigations reveal that the carbon aerogel/Ni foam exhibits superior performances in both aqueous and organic electrolytes involving high specific capacitance and long-term cycling stability. The excellent properties can be ascribed to the unique formation and porous structure, which allows more effective transportations of electron and electrolyte ion.

Creep And Oxidation Of Hafnium Diboride-Based Ultra High Temperature Ceramics At 1500°C, Anthony J. Degregoria

Theses and Dissertations

Ultra high temperature ceramics (UHTCs) are leading candidates for aerospace structural applications in high temperature environments, including the leading edges of hypersonic aircraft and thermal protection systems for atmospheric re-entry vehicles. Before UHTCs can be used in such applications, their structural integrity and environmental durability must be assured, which requires a thorough understanding and characterization of their creep and oxidation behavior at relevant service temperatures.

Turning An Organic Semiconductor Into A Low-Resistance Material By Ion Implantation, Beatrice Fraboni, Alessandra Scidà, Piero Cosseddu, Yongqiang Wang, Michael Nastasi, Silvia Milita, Annalisa Bonfiglio

Nebraska Center for Energy Sciences Research: Publications

We report on the effects of low energy ion implantation on thin films of pentacene, carried out to investigate the efficacy of this process in the fabrication of organic electronic devices. Two different ions, Ne and N, have been implanted and compared, to assess the effects of different reactivity within the hydrocarbon matrix. Strong modification of the electrical conductivity, stable in time, is observed following ion implantation. This effect is significantly larger for N implants (up to six orders of magnitude), which are shown to introduce stable charged species within the hydrocarbon matrix, not only damage as is the case …

High Capacity Silicon Electrodes With Nafion As Binders For Lithium-Ion Batteries, Jiagang Xu, Qinglin Zhang, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

Silicon is capable of delivering a high theoretical specific capacity of 3579 mAh g⁻¹ which is about 10 times higher than that of the state-of-the-art graphite based negative electrodes for lithium-ion batteries. However, the poor cycle life of silicon electrodes, caused by the large volumetric strain during cycling, limits the commercialization of silicon electrodes. As one of the essential components, the polymeric binder is critical to the performance and durability of lithium-ion batteries as it keeps the integrity of electrodes, maintains conductive path and must be stable in the electrolyte. In this work, we demonstrate that electrodes consisting of …

Evolution Of Non-Metallic Inclusions In Foundry Steel Casting Processes, Marc Harris, Von Richards, Ronald J. O'Malley, Semen Naumovich Lekakh

Materials Science and Engineering Faculty Research & Creative Works

The evolution of nonmetallic inclusions was examined for 4320 steel at an industrial steel foundry. The steel was followed from electric arc furnace melting through ladle refining to final casting. Timed sampling was performed at all stages of the process. Samples were analyzed using an automated SEM/EDS system. The overall evolution of oxide inclusions in terms of nucleation, growth, and flotation during liquid processing was studied using area fraction and average diameter. Chemical composition evolution was observed using a joint ternary plotting tool developed under this program. It was found that the use of zirconium as an addition for nitrogen/oxygen …

Ellipsometric Characterization Of Silicon And Carbon Junctions For Advanced Electronics, Alexander G. Boosalis

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Ellipsometry has long been a valuable technique for the optical characterization of layered systems and thin films. While simple systems like epitaxial silicon dioxide are easily characterized, complex systems of silicon and carbon junctions have proven difficult to analyze. Traditional model dielectric functions for layered silicon homojunctions, a system with a similar structure to modern transistors, often have correlated parameters during ellipsometric data analysis. Similarly, epitaxial graphene as grown from thermal sublimation of silicon from silicon carbide or through chemical vapor deposition, tend to have model dielectric function parameters that correlate with the optical thickness of the graphene due to …

Modeling And Simulation Of Micro Electrical Discharge Machining Process, Bai Shao

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Micro parts and systems are playing crucial roles in the area of semiconductor, biomedical device, micro fluid devices, automotive, aerospace and so forth. Micro manufacturing is one of the most important technologies in realizing miniaturization. Compared to other micro manufacturing methods, micro-EDM is drawing lots of attention due to its ability to machine complex 3D parts regardless of the hardness of the workpiece material.

Micro-EDM is the cumulative result of numerous single discharges; therefore, it is crucial to understand the single discharge material removal process in micro-EDM. However, due to the stochastic nature and complex process mechanism, micro-EDM, including its …

Improving Renewable Energy Transition Acceptance: A Simulation Gaming Approach On A Multi Actor Setting In The Netherlands, Aziiz Sutrisno, Jac A. M. Vennix, Noor Syaifudin

Makara Journal of Technology

The Netherlands have tried very hard to increase their renewable energy sources (RES) shares to fulfill the European Union target in 2050. However, RES performance did not show the expected result as the performance declined in 2009 producing even wider gap compare to the target. The Dutch government’s tried to incorporate all interested stakeholders by forming the Dutch energy transition task force. Nevertheless, the task force’s result is also not showing a desirable trend. Key reasons behind the Dutch low RES performance are the lack of shared understanding and positive attitude toward RES development among interested actors. This research uses …

Dual-Band Singly-Fed Proximity-Coupled Tip-Truncated Triangular Patch Array For Land Vehicle Mobile System, Basari Basari, Josaphat Tetuko Sri Sumantyo

Makara Journal of Technology

This paper proposes a dual-band left-handed circularly polarized triangular-patch array that is developed for land vehicle mobile system aimed at mobile satellite communications. The array consists of six tip-truncated triangular patches, which the first three patches are used for reception and the second three patches are used for transmission purpose. Each of three-patches has a beam pattern that can be switched in three different 120°-coverage beam in azimuth-cut plane at a minimum targeted gain at a desired elevation angle. The targeted minimum gain of the array is 5 dBic, in order for data communications with a large geostationary satellite can …