Materials Science and Engineering Commons^™

The Effect Of Green Biobased Binder On Structural, Mechanical, Liquid Absorption And Wetting Properties Of Coated Papers, Bilge N. Altay, Charles Klass, Ting Chen, Alexandar Fleck, Cem Aydemir, Arif Karademir, Paul D. Fleming

Articles

Synthetic styrene-butadiene (SB) and styrene-acrylic (SA) latex binders used in paper coating formulations are common and based on unsustainable petroleum sources. Today's papermaking industry turns towards sustainable substitutes that do not compromise quality, and reduce carbon emission, toxic substance release and waste disposal concerns related to fossil fuel sources. In this study, colloidal starch-based latex nanoparticles that do not require cooking were used for pigment coating and coated on the paper surfaces. The effects of these new biobased binders on the structural and mechanical strength properties, liquid absorption, wetting and surface topography of the paper were investigated and compared with …

Life Cycle Assessment Of Pasture-Based Agrivoltaic Systems: Emissions And Energy Use Of Integrated Rabbit Production, Alexis Pascaris, Robert Handler, Chelsea Schelly, Joshua Pearce

Michigan Tech Publications, Part 1

Agrivoltaic systems, which deliberately maximize the utility of a single parcel of land for both solar photovoltaic (PV) electricity production and agriculture, have been demonstrated as a viable technology that can ameliorate competing land uses and meet growing energy and food demands efficiently. The goal of this study is to assess the environmental impacts of a novel pasture-based agrivoltaic concept: co-farming rabbits and solar PV. A life cycle assessment (LCA) quantified the impacts of 1) the integrated agrivoltaic concept in comparison to conventional practices including 2) separate rabbit farming and PV production and 3) separate rabbit farming and conventional electricity …

Reliability Characterization Of A Low-K Dielectric Using Its Magnetoresistance As A Diagnostic Tool, Philip Alister Williams

Legacy Theses & Dissertations (2009 - 2024)

The introduction of low dielectric constant materials within the integrated circuit (IC) chip technology industry was a concerted effort to decrease the resistance-capacitance (RC) time delay inherent within the dielectric materials used as insulators. This stems from a demand for greater device density per IC chip and decreased feature sizes but is fast becoming a reliability issue. Concomitant with the demand for decreased feature sizes, also in adherence with Moore’s Law (which states that the number of devices on a die doubles every two years), is a reduction in device speed and performance due to device intra-level interconnection signal delays. …

Glycan Functionalization Of Iron Oxide Nanoparticles (Ionps) As A Method Of Inactivating Antibiotic Resistant Neisseria Gonorrhoeae Via A Magnetically Mediated Energy Delivery (Magmed) System, Cedric Taylor

All Theses

With the increase of antibiotic resistant bacteria, current established therapeutic treatment methods are rapidly demonstrating decreasing efficacy. For this project, we are studying a novel alternate mechanism of treating antibiotic resistant bacteria by utilizing magnetic iron oxide nanoparticles (IONPs) coated with a heterobifunctional polyethylene glycol polymer (PEG) and functionalized with glycan structures that can interact with Neisseria gonorrhoeae FA1090. Interaction between the IONPs and bacteria is manipulated by an external alternating magnetic field (AMF) in a process known as magnetically mediated energy delivery (MagMED). Magnetic IONPs were synthesized and reacted with PEG (PEG-IONPs) and functionalized with glycans Gal(α1-3)Gal(β1-4)Glc(β1-1) (common name: …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

Creep Behavior And Deformation Mechanisms Of Spark Plasma Sintered Oxide Ceramics For Aerospace Systems At 1300˚C - 1400˚C, David D. Swanson

Theses and Dissertations

The mechanical behavior of YAG and LuAG was investigated at elevated temperatures. The specific materials investigated in this work include high-purity, polycrystalline YAG, high-purity, polycrystalline LuAG, and two doped variants of YAG: 2at% Yb-doped, polycrystalline YAG and 2at% Er-doped, polycrystalline YAG. Several billets of each material were prepared and processed by means of spark plasma sintering (SPS). Many different sintering parameters were utilized in order to obtain materials with various physical properties and to identify the effects of sintering parameters on the average grain size of the resulting materials. The compressive creep behavior of these materials was investigated at 1300°C …

Simulation And Fabrication Of All Oxide-Based Ito/Tio2/Cuo/Au Heterostructure For Solar Cell Applications, Sajal Islam

Graduate Theses/Dissertations

Oxide heterostructures have drawn great attention lately, due to their environment-friendly properties and potential applications in optoelectronic devices. In this work, a simulation study of a heterojunction solar cell was performed with SCAPS (a solar cell simulator) using TiO2 as an n-type and CuO as a p-type layer. The thickness and the dopant-dependent simulations have shown that the solar cell operates at a maximum efficiency of 19.2% when the thickness of the TiO2/CuO layers is chosen 1.4µm/1.2µm compared to the 11.5% efficiency when FTO is replaced with ITO. An indium-doped tin oxide (ITO) vs fluorine-doped tin oxide (FTO) comparison study …

Silver Microparticle And Submicron Wire - Polylactic Acid Composites For Additive Manufacturing, Jenna W. Robichaux

LSU New Orleans Theses and Dissertations

This thesis explores the incorporation of silver microparticle and submicron wire additives into thermoplastic filament feedstock for fused filament fabrication (FFF) to create multifunctional three-dimensional (3D) printable composites. The impact of silver microparticle and submicron wire additives on mechanical behavior along with antibacterial effect of the silver microparticle and submicron wire additives on printed objects were assessed.

Composite FFF filaments were fabricated by solution processing, granulation, and extrusion. Differential Scanning Calorimetry (DSC) was conducted to measure the glass transition and melting point temperatures of the composite filaments for 3D printing. The effect of the additive addition on the thermal properties …

Investigation Of Optical And Structural Properties Of Gesn Heterostructures, Oluwatobi Gabriel Olorunsola

Graduate Theses and Dissertations

Silicon (Si)-based optoelectronics have gained traction due to its primed versatility at developing light-based technologies. Si, however, features indirect bandgap characteristics and suffers relegated optical properties compared to its III-V counterparts. III-Vs have also been hybridized to Si platforms but the resulting technologies are expensive and incompatible with standard complementary-metal-oxide-semiconductor processes. Germanium (Ge), on the other hand, have been engineered to behave like direct bandgap material through tensile strain interventions but are well short of attaining extensive wavelength coverage. To create a competitive material that evades these challenges, transitional amounts of Sn can be incorporated into Ge matrix to form …

Using Peptide Design To Engineer Polyelectrolyte Complex Biomaterials, Sara Tabandeh

Electronic Theses and Dissertations, 2020-2023

The self-assembly of oppositely charged polymers provides a versatile platform to design materials for diverse applications in biology and medicine. Electrostatically-driven phase separation of oppositely charged polymers in aqueous solution gives rise to the formation of a polymer-rich phase called a polyelectrolyte complex (PEC). PECs can be in the form of liquid droplets (complex coacervates) or amorphous solid precipitates. Unlike synthetic polymers, peptides are good candidates for developing tailor-made formulations and structure-property relationships due to their biocompatibility, precise control over sequences, and ability to program hydrogen bonding interactions. However, little is known about the effect of combining additional molecular interactions …

Anisotropy In Impact Toughness Of Powder Bed Fused Aisi 304l Stainless Steel, Sreekar Karnati, Atoosa Khiabhani, Aaron Flood, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The current effort involved investigation into the anisotropy of AISI 304L fabricated through laser powder bed fusion. Charpy V‐notch specimens made from material fabricated at three different build orientations were tested and analyzed. A statistically significant difference among the toughness values indicates the presence of anisotropy within the additively manufactured material. While the lowest toughness was found in vertically built specimens, the horizontal specimens were found to exhibit the highest toughness. From the fracture surfaces, an atypical mode of failure was observed. Exclusive crack propagation along the interlayer track boundaries was observed. The toughness variation correlated with the ease of …

Automated Mini-Tubular Ceramic Production, Hunter Brooks, Daniel Freeman, Leo Taranta-Slack

Mechanical Engineering

Researchers at Lawrence Livermore National Laboratory need a way to increase the rate of manufacturing of mini-tubular ceramics to be used in testing particulate air filters. This document outlines our process from researching and writing an initial scope of work all the way to fabricating and testing a final prototype. This journey takes us through the background research, ideation process and selection of a final design. We also detail the desired engineering specifications and our concept selection process. We dedicate a significant portion of this report to discussion of our final design. We delve into how it was manufactured as …

Dreams Of Molecular Beams: Indium Gallium Arsenide Tensile-Strained Quantum Dots And Advances Towards Dynamic Quantum Dots (Moleculare Radiorum Somnia: Indii Gallii Arsenicus Tensa Quanta Puncta Et Ad Dinamicae Quantae Puntae Progressus), Kevin Daniel Vallejo

Boise State University Theses and Dissertations

Through the operation of a molecular beam epitaxy (MBE) machine, I worked on developing the homoepitaxy of high quality InAs with a (111)A crystallographic orientation. By tuning substrate temperature, we obtained a transition from a 2D island growth mode to step- ow growth. Optimized MBE parameters (substrate temperature = 500 °C, growth rate = 0.12 ML/s and V/III ratio ⩾ 40) lead to growth of extremely smooth InAs(111)A films, free from hillocks and other 3D surface imperfections. We see a correlation between InAs surface smoothness and optical quality, as measured by photoluminescence spectroscopy. This work establishes InAs(111)A as a platform …

How To Recognize And Control Interfacial Phenomena That Hinder The Advancement Of Clean Energy Technologies, Corey Michael Efaw

Boise State University Theses and Dissertations

Nuclear energy and electrochemical energy storage, such as batteries, are key parts to the clean energy transition of critical infrastructure. This work aims to define, monitor, and modify interfacial layers that would improve the utility of materials in harsh environments seen in nuclear and energy storage applications. First, the studying of zirconium alloys, which is used as nuclear cladding, was done to better understand the degradation mechanisms within an extreme environment. High-resolution characterization techniques were used to correlate corrosion mechanisms to equivalent circuit models from novel in-pile electrochemical impedance spectroscopy sensors. Advancement in this sensor technology could provide further insight …

Synthesis And Characterization Of 4,6-Protected Glucosamine Derivatives And Branched Glycoconjugates, Jonathan Bietsch

Chemistry & Biochemistry Theses & Dissertations

Low molecular weight gelators (LMWGs) are small molecules that self-assemble in appropriate solvents to form three dimensional networks that immobilize the solvent, creating a supramolecular gel. The self-assembly of LMWGs occurs through non-covalent interactions such as hydrogen bonding, aromatic interactions, donor-acceptor interactions, Van der Waals interactions, hydrophobic forces, halogen bonding, etc. Due to self-assembly occurring through reversible non-covalent interactions, supramolecular gels can undergo a gel to solution transformation. Because of this, these materials can be sensitive to external stimuli such as temperature changes, pH changes, and other stimuli that effect non-covalent interactions. This makes the synthesis of LMWG’s an appealing …

Tensile-Strained Self-Assembly Of Ingaas On Inas(111)A, Kevin D. Vallejo, Trent A. Garrett, Carlos I. Cabrera, Baolai Liang, Kevin A. Grossklaus, Paul J. Simmonds

Materials Science and Engineering Faculty Publications and Presentations

We have determined a reproducible set of growth conditions for the self-assembly of tensile-strained In_1-xGa_xAs quantum dot (QD) nanostructures on (111)A surfaces. During molecular beam epitaxy, In_1-xGa_xAs islands form spontaneously on InAs(111)A when the Ga content x ≥ 50%. We analyze the structure and composition of InGaAs/InAs(111) samples using atomic force microscopy, transmission electron microscopy, and electron energy loss spectroscopy. We demonstrate control over the size and areal density of the islands as a function of In_1-xGa_xAs coverage, In_1-xGa_xAs composition, …

Mechanical Interfacial Locking And Multiscale Modeling Of Reinforced Thermoplastic Composites For Structural Applications, Anmol Kothari

All Dissertations

The ever-growing pressure of reducing the adverse impact of transportation systems on environment has pushed industries towards fuel-efficient and sustainable solutions. While several approaches have been used to improve fuel efficiency, the light-weighting of structural components has proven broadly effective. In this regard, reinforced thermoplastic composites (RTPC), owing to their high recyclability, higher impact strength and fast cycle times, have become competitive candidates at an industrial scale. However, to implement RTPC toward large scale structural applications several challenges pertaining to material design and manufacturing effects need to be addressed. To this end, a computational study is carried out to address …

Investigation And Characterization Of New Optically Stimulated Luminescence (Osl) Dosimetric Materials, Linyu Pan

All Dissertations

Optically stimulated luminescence (OSL) dosimeters have attracted increasing attention due to advantages over TL dosimeters, including no thermal quenching and higher sensitivity. Nevertheless, currently, there are only two commercially available OSL dosimeters, BeO and Al₂O₃:C. An OSL dosimeter requires low effective atomic number (Z_eff < 16), at least one type of recombination center and one type of trap, and UV~blue emission. In this dissertation, motivated by the search of new OSL dosimetric materials, a systematic investigation of alumina (Z_eff = 11.3) and magnesium aluminate spinel (Z_eff = 11.2) based materials was performed in terms of the engineering of the recombination centers and electronic traps. Microstructural characterization was executed by means of X-ray diffraction (XRD) and Raman spectroscopy. Luminescence was characterized under X-ray excitation (radioluminescence; RL) at ambient and …

Microstructural And Optical Properties Of Mgal2o4 Spinel: Effects Of Mechanical Activation, Y2o3 And Graphene Additions, Nina Obradovic, William Fahrenholtz, Cole Corlett, Suzana Filipovic, Marko Nikolic, Bojan A. Marinkovic, Simone Failla, Diletta Sciti, Daniele Di Rosa, Elisa Sani

Materials Science and Engineering Faculty Research & Creative Works

Magnesium Aluminate and Other Alumina-Based Spinels Attract Attention Due to their High Hardness, High Mechanical Strength, and Low Dielectric Constant. MgAl₂O₄ Was Produced by a Solid-State Reaction between MgO and Α-Al₂O₃ Powders. Mechanical Activation for 30 Min in a Planetary Ball Mill Was Used to Increase the Reactivity of Powders. Yttrium Oxide and Graphene Were Added to Prevent Abnormal Grain Growth during Sintering. Samples Were Sintered by Hot Pressing under Vacuum at 1450◦C. Phase Composition and Microstructure of Sintered Specimens Were Characterized by X-Ray Powder Diffraction and Scanning Electron Microscopy. Rietveld Analysis Revealed 100% …

Synthesis, Crystal Structure And Ionic Conductivity Of Ruddlesden-Popper Oxide Materials: Effects Of Ionic Radii And Defects On Lithium-Ionic Conductivity., Selorm Joy Fanah

Electronic Theses and Dissertations

Layered perovskite oxides of the Ruddlesden-Popper (RP) type structure can be good lithium-ion conductors for solid electrolyte applications in all-solid-state batteries, due to the large gap separating octahedral layers which can be useful pathways for Li-ion conduction. However, little work has been done on their lithium-ion transport properties in these materials despite their interesting structural properties. This work highlights the synthesis and study of the ionic conductivities in a series of n = 2 and 3 Ruddlesden-Popper oxides, as part of an ongoing investigation in search of alternative solid electrolyte materials. Several different strategies were employed for the enhancement of …