Power and Energy Commons^™

Circuit Breaker Module, Garvin Yee, Yei Trinh

Electrical Engineering

The circuit breaker module for this design project is a proof of concept that demonstrates the functionality, feasibility, and attainability of a consumer grade power systems analysis device suitable for college laboratory use. The goal of this project was to create the final iteration of a module that has been developed and refined over the course of previous years. The Cal Poly Electrical Engineering Department intends to use this design to produce circuit breaker modules intended for fault analysis. With the current changes made to the previous modules, the current circuit breaker is lighter, safer, and more universally reproducible. The …

Analysis Of Improved Multiphase Buck Converter, Usamah Riaz Ahmad, Scott Wu

Electrical Engineering

While the number of transistors per microprocessor is rapidly increasing, the power requirements of converters are getting more and more important. The amount of current is increasing, while at the same time the output voltage is steadily decreasing. Today’s boards are exceeding 100A, while the buck converters have their output voltage below 1 V. Due to these new power requirements, multiphase buck converters are becoming more popular. In addition, this topology is usually used with voltage regulator modules (VRM).

The TPS40090EVM-002 board was used as the original multiphase buck with an input voltage of 12 V and output voltage of …

Investigating Efficiency Of Ac Direct Drive Of Led Lighting, Miles Davis Head

Electrical Engineering

This project explores the rapidly-expanding area of AC direct drive for LED lighting. AC LED driving does not use typical DC-DC converter-based driving but uses semiconductor switches and a linear regulator to activate a number of LEDs proportional to the input voltage at any given time. This allows bulky, expensive magnetics to be eliminated from the system. The goal of this project was to develop a flexible simulation of a common AC LED system to find areas of significant power loss and attempt to improve them. This allows future versions of an AC LED system to start with major loss …

Ewall Inverter Project, Andrew Douglas Tsau, Alex Lopez

Electrical Engineering

The objective of this project is to demonstrate the capabilities of a Raspberry Pi when used as a grid-tied, bi-directional power inverter for renewable energy storage applications. Due to its economical nature, this system would play a large role in the growing solar industry by making solar energy more accessible, affordable, and easier to install. The inverter uses a single-phase H-Bridge to generate a sine wave from a proprietary wall mounted battery. To improve power quality, an enhanced low pass filter is added to provide a better drop off to reduce extraneous harmonics. The system synchronizes this synthetic sine wave …

Design And Test Of Wide Input And Output Constant Current Led Driver, Kean Wee

Electrical Engineering

This senior project aims to provide design and test the performance of a DC-DC constant current LED driver for use in a larger DC smart building infrastructure. In this instance, a SEPIC topology is chosen to provide high efficiency output current at output voltages that can be above or below the input voltage. This is challenging since the same design must operate at similar efficiency for vastly different environmental conditions. As a part of a larger system, the design must be able to perform the given task consistently regardless of changes to the source and load power.

The design uses …

A Multiphase Modified Boost Converter With Reduced Input Current Ripple: Combined Capacitors, Omri Nissan

Master's Theses

The delivery of high power and smaller footprints through a non-isolated topology demands for the use of multiphase topology in DC-DC converters. Multiphase reduces the ripple observed on both the input and output waveforms; however, it may not be enough to connect to sensitive power sources such as renewable energy sources. A single-phase modified boost converter demonstrates the ability to acquire very minimal input current ripple by addition of passive components. The expansion to multiphase topology is the next logical step for higher power application while furthering the low input current ripple benefit. In this thesis, the multiphase modified boost …

The Analysis And Study Of Power System Designs For Same Polytechnic College In Tanzania, Kevin Lum Hua

Master's Theses

The Mbesese Initiative for Sustainable Development (MISD) is a group aiming to help eliminate extreme poverty in Africa by creating educational opportunity. One project that the group is currently doing is to build Same Polytechnic College (SPC) in Tanzania. As part of the project, this thesis aims to study and analyze the electrical power system and distribution for the college. Based on the projected load profile of the college and high potential for solar generation in Tanzania, several different power systems utilizing local utility AC electricity and/or photovoltaic (PV) DC electricity are explored and simulated for their feasibility and performance. …

The Modified-Multiphase Boost Converter: Combined Inductors And Capacitors Topology, Zachary L. Eldredge

Master's Theses

In this work, a modified boost converter design has been implemented in a multiphase configuration with a condensed topology. The modified aspect of the design has already been proven to drastically reduce input current ripple by about 40% in a single-phase implementation. By placing two modified boost converters in parallel with interleaving main switches (multiphase), the input inductors and modified capacitors of the modified topology can be reduced to just one of each, lowering the number of components, size, and cost. Additionally, multiphase DC/DC converters lower input/output voltage and current ripples while delivering more power compared to single-phase converters. By …

Electric Upgrades - Supercapacitor Electric Bicycle, John Chen, Wilson Fletcher, Spencer Esparza

Electrical Engineering

Supercapacitors provide high current capabilities compared to conventional lithium-ion batteries, allowing for fast charging and discharging of electrical energy. This project seeks to test the benefits of supercapacitors in an electric bicycle unit in order to gain higher regenerative energy. The main components of the bicycle are its regenerative motor, supercapacitor array, and motor controller. Developing the project will provide data on the feasibility of using alternative battery storage and charging.

Fault Identification And Location For Distribution Network With Distributed Generations, Wen Fan, Yuan Liao

Electrical and Computer Engineering Faculty Publications

Power distribution networks with distributed generations may experience faults. It is essential to promptly locate the fault for fast repair and restoration. This paper presents a novel method for identifying the faulted section and accurate location of faults that occur on power distribution grid. Appropriate matrices are set up to represent meter locations on the grid and the topology of the grid. The voltage and current measurements obtained are utilized to decide the fault sections. Then fault location is determined by solving equations that link measurements and fault locations through bus impedance matrix. The method is applicable to both single …

Applications Of Complex Network Analysis In Electric Power Systems, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

This paper provides a review of the research conducted on complex network analysis (CNA) in electric power systems. Moreover, a new approach is presented to find optimal locations for microgrids (MGs) in electric distribution systems (EDS) utilizing complex network analysis. The optimal placement in this paper points to the location that will result in enhanced grid resilience, reduced power losses and line loading, better voltage stability, and a supply to critical loads during a blackout. The criteria used to point out the optimal placement of the MGs were predicated on the centrality analysis selected from the complex network theory, the …

Performance Evaluation Of Energy-Autonomous Sensors Using Power-Harvesting Beacons For Environmental Monitoring In Internet Of Things (Iot), George Dan Moiş, Teodora Sanislav, Silviu Corneliu Folea, Sherali Zeadally

Information Science Faculty Publications

Environmental conditions and air quality monitoring have become crucial today due to the undeniable changes of the climate and accelerated urbanization. To efficiently monitor environmental parameters such as temperature, humidity, and the levels of pollutants, such as fine particulate matter (PM2.5) and volatile organic compounds (VOCs) in the air, and to collect data covering vast geographical areas, the development of cheap energy-autonomous sensors for large scale deployment and fine-grained data acquisition is required. Rapid advances in electronics and communication technologies along with the emergence of paradigms such as Cyber-Physical Systems (CPSs) and the Internet of Things (IoT) have led to …

Perovskite Solar Cells Fabricated Via Scalable Dip Coating Methods, Joseph F. Iannello

Theses and Dissertations

Perovskite solar cells present the possibility for less expensive electricity generation, through the use of low cost materials and fabrication methods relative to current silicon-based technology. Many current methods of fabricating thin film perovskite solar cells focus on spin-coating, which inherently lacks scalability due to particle conglomeration, poor uniformity over a larger area, and safety concerns. Dip-coating, an alternative to spin-coating, which is explored here addresses these issues which limit scalability. Each individual layer can be separately synthesized, deposited, and characterized, which leads towards scalability. Choosing only the best results from each independent layer allowed progress to the creation of …

Applications Of Artificial Intelligence In Power Systems, Samin Rastgoufard

LSU New Orleans Theses and Dissertations

Artificial intelligence tools, which are fast, robust and adaptive can overcome the drawbacks of traditional solutions for several power systems problems. In this work, applications of AI techniques have been studied for solving two important problems in power systems.

The first problem is static security evaluation (SSE). The objective of SSE is to identify the contingencies in planning and operations of power systems. Numerical conventional solutions are time-consuming, computationally expensive, and are not suitable for online applications. SSE may be considered as a binary-classification, multi-classification or regression problem. In this work, multi-support vector machine is combined with several evolutionary computation …

Tolerance Sensitivity Analysis And Robust Optimal Design Method Of A Surface-Mounted Permanent Magnet Motor By Using A Hybrid Response Surface Method Considering Manufacturing Tolerances, Cha-Seung Jun, Byung-Il Kwon, Ohbong Kwon

Publications and Research

This paper presents a robust optimal design method using a hybrid response surface method (H-RSM) which directly finds an optimal point satisfying a target Z-value or a probability of failure. Through three steps, this paper achieves the goal that is to increase the open-circuit airgap flux (OCAF) in a surface-mounted permanent magnet motor and decrease its variation caused by variations of the airgap lengths including an additional one between permanent magnets and rotor back yoke. First, the OCAF equation is derived from the magnetic equivalent circuit (MEC) considering the additional airgap. Then, the equation is validated by comparing its results …

Comparison Of Data Transfer Alternatives In Asynchronous Circuits, Mark Howard

Computer Science and Computer Engineering Undergraduate Honors Theses

Digital integrated circuits (ICs) have become progressively complex in their functionality. This has sped up the demand for asynchronous architectures, which operate without any clocking scheme, considering new challenges in the timing of synchronous systems. Asynchronous ICs have less stringent environmental constraints and are capable of maintaining reliable operation in extreme environments, while also enjoying potential benefits such as low power consumption, high modularity, and improved performance. However, when the traditional bus architecture of synchronous systems is applied to asynchronous designs, handshaking protocols required for asynchronous circuit operation result in significantly increased power consumption, offsetting the low power benefit of …

Scada And Plc Systems Configuration For The Ncrept Test Facility, Arman Ahmed

Electrical Engineering Undergraduate Honors Theses

This thesis details the project to update the control and interface system of the National Center for Reliable Electric Power Transmission (NCREPT) testing facility. The need for this project arose from the 2017-2018 expansion of the facility, which included some modifications in the layout of electrical equipment used for testing purposes. These modifications necessitated the update of the control and interface system. Additionally, the old system was implemented a decade ago and is nearing obsolescence, so the facility’s expansion served as an opportune time for an upgrade.

There were two main parts to the scope of this project, which were …

A Human Powered Micro-Generator For Charging Electronic Devices, John Adam

Senior Theses

A hand-pulled generator has been designed and tested. A preliminary result has been obtained and discussed. This device was created to provide outlet-free charging. Electronic devices are useful when going out into the wilderness. A portable power supply is necessary to keep an electronic device alive. This project created a device that converts human energy into electricity to charge electronic devices. This thesis overviews the device’s design, build, and tests. Two different tests were run to determine that the device is capable of charging the storage battery. The device presented can provide 14 minutes of charging time with one hour …

Increasing The Longevity Of Tungsten Filaments In A Zone Refiner, Byron D. Greenlee

Senior Theses

Zone refining is used for its ability to purify material and grow single crystals. To produce these single crystals, a suspended molten zone, generated by electron bombardment, passes along the polycrystalline stock. During a zone refining run, the filaments that produce the electron bombardment can fail. In this project, the longevity of tungsten filaments in a zone refiner was investigated. A new bombardment geometry was constructed to attempt to increase the longevity of the filaments. The new geometry had a shield machined into it to prevent line-of-sight impurities originating in the molten zone from striking the filaments. It was found …

Measuring The Double Layer Capacitance Of Electrolyte Solutions Using A Graphene Field Effect Transistor, Agatha Ulibarri

Senior Theses

When operating graphene field effect transistors (GFETs) in fluid, a double layer capacitance (C_dl) is formed at the surface. In the literature, the C_dl is estimated using values obtained using metal electrode experiments. Due to the distinctive electronic and surface properties of graphene, there is reason to believe these estimates are inadequate. This work seeks to directly characterize the double layer capacitance of a GFET. A unique method for determining the C_dl has been implemented, and data has been obtained for three electrolytes and one ionic fluid. The results yield dramatically lower C_dl values than …