Aerospace Engineering Commons^™

Effect Of Stitch Density On Fatigue Characteristics And Damage Mechanisms Of Stitched Carbon/Epoxy Composites, Arief Yudhanto, Naoyuki Watanabe, Yutaka Iwahori, Hikaru Hoshi

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The effect of stitch density (SD) on fatigue life, stiffness degradation and fatigue damage mechanisms in carbon/epoxy (T800SC/XNRH6813) stitched using Vectran thread is presented in this paper. Moderately stitched composite (SD = 0.028/mm²; 'stitched 6 x 6') and densely stitched composite (SD = 0.111/mm²; 'stitched 3 x 3') are tested and compared with composite without stitch thread (SD = 0.0; 'unstitched'). The experiments show that the fatigue life of stitched 3 x 3 is moderately better than that of unstitched and stitched 6 x 6. Stitched 3 x 3 pattern is also able to postpone the …

Flexible Slosh Diaphragm Modeling And Simulation In Propellant Tanks, Darren Vaughn Levine

Theses and Dissertations

iquid sloshing and propellant distribution is an important field of research for aerospace applications such as launch vehicles and spacecraft. The propellant mass behavior can greatly influence vehicle dynamics, altering trajectories and structural loading distributions. In order to combat these concerns some propellant tanks employ thin elastomeric diaphragms to separate the fuel from the gas volumes and restrict the fluid's motion. The diaphragm’s flexible behavior is generally highly nonlinear, and various propellant fill levels and acceleration conditions can cause large deflections resulting in complex buckling and folding patterns. When complex and non-uniform deformations occur, there is potential for diaphragm wear …

Cti White Paper, Tim Brady, Gregory Mcguirk

Publications

The FAA Air Traffic Collegiate Training Initiative (AT-CTI) Program has 36 partner institutions across the United States which offer a variety of accredited academic degrees and actively promote a multicultural and diverse collegiate environment.

The Pocketqube Concept, Robert J. Twiggs, J. G. Jernigan, L. R. Cominsky, L. R. Malphrus, B. K. Silverman, K. Zack, S. Mcneil, W. Roach-Barrett, T-Logoqube

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs and associates titled "The PocketQube Concept" from April 23, 2014.

Performance Improvement Through Velocity Triangle Optimization-Driven Redesign For Mitigating The Horseshoe Vortex In Axial Turbines, Vladislav Shulman

Doctoral Dissertations and Master's Theses

Momentum differences between the neighboring streamlines at the end wall/primary flow interaction region of an axial turbine stage induce three-dimensional vortical flow structures, such as the leading edge horseshoe vortex, resulting in significant aerodynamic performance deterioration. Reducing the effect of such flow instabilities requires turbine blade modification to discourage boundary layer roll-up, but traditional structural modification design systems can be prohibitively complex and time-intensive.

To address this problem, this study contributes a blade modification method involving airfoil shape optimization, designed to adjust the leading edge airfoil shape in horseshoe vortex-affected turbine applications. The key insight is that airfoil design (treated …

Innovative Uses Of The Canisterized Satellite Dispenser (Csd), Robert J. Twiggs, Walter Holemans, Ryan Williams, Andrew Kalman, Rex Ridenoure, Tom Walkinshaw, Ryan Hevner, Floyd Azure

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Walter Holemans, Ryan Williams, Andrew Kalman, Robert Twiggs, Rex Ridenoure, Tom Walkinshaw, Ryan Hevner, and Floyd Azure titled "Innovative Uses of the Canisterized Satellite Dispenser (CSD)" from April 16, 2014.

Subtalar Fusion Fixture Design And Test, Andrew Campbell

Honors Theses

An experiment was designed to quantify the relative displacement between the calcaneus and talus ankle bones during various types of loading. The ankles were embedded in an epoxy resin and three loads were applied: compressive forces, flexion moments, and inversion moments. A stereo camera system took photographs during the loading process, and the images were correlated via digital image correlation (DIC). The DIe was carried out via a suite of homemade programs written using the open-sourced computational program Octave.

Characterization Of The Flow Field Over An Ablative Surface, Michael Allard, C. M. White, Y. Dubief

Ablation Workshop

No abstract provided.

Experimental Determination Of Pyrolysis Products From Carbon/Resin Ablative Materials, Hsi-Wu Wong, Jay Peck, Robin Edwards, Guillaume Reinisch, Jean Lachaud, Nagi N. Mansour

Ablation Workshop

No abstract provided.

Remote Recession Sensing Of Ablative Heat Shield Materials, Michael Winter, Margaret Stackpoole, Anuscheh Nawaz, Gregory Lewis Gonzales, Thanh Ho

Ablation Workshop

No abstract provided.

In-Situ Recession Measurements By Photogrammetric Ablator Surface Analysis, Stefan Löhle, T. Staebler, T. Reimer, A. Cefalu

Ablation Workshop

No abstract provided.

A Light-Weight Ablative Material For Research Purposes, Thomas Rothermel, C. Zuber, G. Herdrich, L. M. G. F. M. Walpot

Ablation Workshop

No abstract provided.

Electroplating Of Nickel And Copper Layers On Nanoengineered Plastics, Brandon Voelker, Muralidhar K. Ghantasala, Jeff Wheeler

Research and Creative Activities Poster Day

Introduction

• The motivation for this project is the development and proposed use of novel nanoengineered polymeric materials in many industrial and commercial applications. This necessitated the development of a robust metallic coating that can withstand aggressive environmental conditions.
• This research explores the methods of electroplating nickel and copper to the substrate, including the effects of various duty cycles and cathode current density

Ablation Test Case Series #3, Tom Van Eekelen, Alexandre Martin, Jean Lachaud, Daniele Bianchi

Ablation Workshop

No abstract provided.

Overview Of Ablation Test-Cases, Alexandre Martin, Jean Lachaud, Tom Van Eekelen, Ioana Cozmuta, Michael Wright, Nagi N. Mansour, Daniele Bianchi

Ablation Workshop

No abstract provided.

Microscale Modeling Of Ablative Thermal Protection System Materials, Eric Stern, Graham Candler, Tom Schwartzentruber, Ioannis Nompelis, Michael Barnhardt

Ablation Workshop

No abstract provided.

Material Response Characterization Of New-Class Ablators In View Of Numerical Model Calibration, Bernd Helber, Alessandro Turchi, T. E. Magin

Ablation Workshop

No abstract provided.

Uncertainty Analysis Of Carbon Ablation In The Vki Plasmatron, Alessandro Turchi, P. M. Congedo, Bernd Helber, T. E. Magin

Ablation Workshop

No abstract provided.

Investigation Of Surface Radiation In Earth Re-Entry Flows With Graphite Ablation, Christopher Alba

Ablation Workshop

No abstract provided.

Surface Effects And Phenomena On Ablative Materials, Alexandre Martin

Ablation Workshop

No abstract provided.