Aerospace Engineering Commons^™

From Xst To F-117a, Alan Brown

ERAU Prescott Aviation History Program

Learn the remarkable story of stealth technology from the man often referred to as “Mr. Stealth.” From 1975-1989 Alan Brown was a member of Lockheed “Skunk Works”, becoming program manager & chief engineer for the F-117A Stealth Fighter from initial concept until the first production aircraft was built, 1978 to 1982. Hear the inside story of the many challenges faced by the stealth program and how they were solved.

Pocketcubes/Cubesats On Antares, Robert J. Twiggs, Walter Holemans, Michael Bitzer

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs, Walter Holmans, and Michael Bitzer titled "PocketCubes/CubeSats on Antares" from September 6, 2016.

Experimental Investigation On Flow Characteristics Of A Four-Wing Micro Air Vehicle, Lisong Shi, Chunkit Uy, Shih K. Huang, Zifeng Yang, George P.G. Huang, Chihyung Wen

Mechanical and Materials Engineering Faculty Publications

The aim of current research work on micro air vehicles is to realize their autonomous control, i.e. building a library for a lookup table that would apply to micro electronics. In doing so, comprehensive flight tests need to be carried out. In this study, a four-wing flapping MAV is built and a multi-discipline approach is used to design the MAV model. Precision manufacturing technology is introduced here. The finished micro air vehicle has a weight of 8 g and is tested for flight by remote control. The micro air vehicle can perform both hovering and forward flight with high maneuverability. …

Numerical Modeling Of Dust Dynamics Around Small Asteroids, William Yu, Joseph J. Wang, Daoru Frank Han

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Dynamics of dust transport around an airless body has been a focused area of research in recent years, however, various challenging aspects still remain to be addressed. This paper presents an investigation of charged dust transport and distribution around small asteroids utilizing a full particle Particle-in-Cell (PIC) model to simulate plasma flow around an asteroid and calculate surface charging self-consistently from charge deposition on asteroid. Material properties of asteroid are also explicitly included in the simulation. PIC simulation results are fed into a 3D dust dynamics model to simulate charged dust levitation, transport and distribution. In addition to electrostatic and …

Experimentation Of Mode I And Mode Ii Fracture Of Uni-Directional Composites And Finite Element Analysis Of Mode I Fracture Using Cohesive Contact, Joseph Daniel Garrett

Master's Theses

As the use of fiber-reinforced composites has increased over the decades, so has the need to understand the complexity of their failure mechanisms as engineers seek to improve the damage tolerance of composite laminated structures. One of the most prevalent and limiting mode of failure within composite laminates is delamination, since it not only reduces a structures stiffness and strength, but can be very difficult to detect without the use of special non-destructive equipment. Industry testing organizations have utilized several fracture tests in order to characterize the fracture toughness of composite materials under different loading conditions. For this research, ASTM …

Propulsion Theory Of Flapping Airfoils, Comparison With Computational Fluid Dynamics, Doug F. Hunsaker, W. F. Phillips

Mechanical and Aerospace Engineering Faculty Publications

It is shown that the time-dependent aerodynamic forces acting on a flapping airfoil in forward flight are functions of both axial and normal reduced frequencies. The axial reduced frequency is based on the chord length, and the normal reduced frequency is based on the plunging amplitude. Furthermore, the time-dependent aerodynamic forces are related to two Fourier coefficients, which are evaluated here from computational results. Correlation equations for these Fourier coefficients are obtained from a large number of grid- and time-step-resolved inviscid computational-fluid-dynamics solutions, conducted over a range of both axial and normal reduced frequencies. The correlation results can be used …

High-Frequency Instabilities Of Stationary Crossflow Vortices In A Hypersonic Boundary Layer, Fei Li, Meelan Choudhari, Pedro Paredes-Gonzalez, Lian Duan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Hypersonic boundary layer flows over a circular cone at moderate incidence angle can support strong crossflow instability in between the windward and leeward rays on the plane of symmetry. Due to more efficient excitation of stationary crossflow vortices by surface roughness, such boundary layer flows may transition to turbulence via rapid amplification of the high-frequency secondary instabilities of finite-amplitude stationary crossflow vortices. The amplification characteristics of these secondary instabilities are investigated for crossflow vortices generated by an azimuthally periodic array of roughness elements over a 7° half-angle circular cone in a Mach 6 free stream. The analysis is based on …

Experimental And Numerical Investigations Of Dust Effects On Surface Charging In Plasma, Kevin Chou, Daoru Frank Han, Joseph J. Wang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A series of 3-D, fully kinetic particle-in-cell (PIC) simulations were performed to simulate mesothermal plasma flow self-consistently with surface charging. Simulation results of plasma charging of a conducting surface covered by a thin dust layer in a plasma of cold ions and thermal electrons are presented. The surface potentials and potentials inside the dust layer are compared with experimental results. Results show that a layer of dust over a conducting surface creates a capacitance, which drives the surface more negative with respect to the ambient plasma.

A Hybrid Optimization Technique Applied To The Intermediate-Target Optimal Control Problem, Clay J. Humphreys, Richard G. Cobb, David R. Jacques, Jonah A. Reeger

Faculty Publications

The DoD has introduced the concept of Manned-Unmanned Teaming, a subset of which is the loyal wingman. Optimal control techniques have been proposed as a method for rapidly solving the intermediate-target (mid-point constraint) optimal control problem. Initial results using direct orthogonal collocation and a gradient-based method for solving the resulting nonlinear program reveals a tendency to converge to or to get `stuck’ in locally optimal solutions. The literature suggested a hybrid technique in which a particle swarm optimization is used to quickly find a neighborhood of a more globally minimal solution, at which point the algorithm switches to a gradient-based …

Citizensatellite: Low Cost Missions For The Unordinary Innovator, Robert J. Twiggs, Amin Djamshidpour, Ted Tagami, Tony So

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Robert Twiggs, Amin Djamshidpour, Ted Tagami, and Tony Sotitled "CitizenSatellite: Low Cost Missions for the Unordinary Innovator" from August 19, 2016.

Secondary Launch Opportunities Orbital Atk, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "Secondary Launch Opportunities Orbital ATK" from August 17, 2016.

On Event-Triggered Adaptive Architectures For Decentralized And Distributed Control Of Large-Scale Modular Systems, Ali Albattat, Benjamin C. Gruenwald, Tansel Yucelen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The last decade has witnessed an increased interest in physical systems controlled over wireless networks (networked control systems). These systems allow the computation of control signals via processors that are not attached to the physical systems, and the feedback loops are closed over wireless networks. The contribution of this paper is to design and analyze event-triggered decentralized and distributed adaptive control architectures for uncertain networked large-scale modular systems; that is, systems consist of physically interconnected modules controlled over wireless networks. Specifically, the proposed adaptive architectures guarantee overall system stability while reducing wireless network utilization and achieving a given system performance …

Experimental Study Of Simulated Geophysical Buoyancy-Driven Vortical Flow, Mohammad Hady Makhmalbaf

Dissertations

This paper describes an experimental study on the flow within a rotating cylinder with a counter-rotating disk located below to mimic certain aspects of the unique flow structures of the Great Red Spot (GRS) in Jupiter using a simple laboratory setup. The special design of this setup makes it capable of spinning the side wall of a vertical cylinder in both directions as well as rotating the bottom of the cylinder independently, where both can rotate in wide ranges of spin rates. Also, different thermal conditions can be applied on the bottom of the disk. All of these conditions provide …

Shape Optimization Of Supersonic Bodies To Reduce Sonic Boom Signature, Junhui Li

McKelvey School of Engineering Graduate Student Theses & Dissertations

In recent years there has been resurgence of interest by aerospace industry and NASA in supersonic transport aircraft. In recent studies, the emphasis has been on shape optimization of supersonic plane to reduce the acoustic signature of sonic boom resulting from the supersonic aircraft at high altitude in cruise flight. Because of the limitations of in-flight testing and cost of laboratory scale testing, CFD technology provides an attractive alternative to aid in the design and optimization of supersonic vehicles. In last decade, the predictive capability of CFD technology has significantly improved because of substantial increase in computational power, which allows …

2015-2016 Eraudb Aiaa Design/Build/Fly Technical Report, Trevor W. Perrott

Student Works

The economic potential of small unmanned aerial vehicles (SUAVs) has been well documented and reported. According to the Association for Unmanned Vehicle Systems International (AUVSI), there is an associated economic impact from the growth of the UAV industry. The goal of the American Institute of Aeronautics and Astronautics Design/Build/Fly Competition Research Program (AIAA DBF CRP) is to investigate design and manufacturing methods for application to SUAVs within the scope of the AIAA DBF Competition.

Students were engaged in the application of aerospace engineering knowledge for the production of a dual-aircraft system. Through the use of Computational Fluid Dynamics (CFD), Computer …

Development Of A "Multi-Cut" Payload For Use In Stratospheric Ballooning Missions, James Flaten, Joey Habeck, Noah Biniek, Steven Smeaton, Austin Langford, Jordan Diers, Isaac Krieger

2017 Academic High Altitude Conference

The ability to cut strings (AKA lines) during stratospheric ballooning missions has a wide variety of uses including, but not limited to, (a) flight termination (i.e. cutting payloads away from the main balloon), (b) cutting away excess lift balloon(s) to slow ascent rate (and possibly achieve float), (c) cutting away ballast weights to slow descent rate or increase ascent rate, (d) cutting away burst balloon(s) on descent to avoid parachute entanglement, and (e) cutting away payloads which are intended to return to the ground independently, for experimental purposes. We report on the development of a “multi-cut” payload box that uses …

Citizen Satellite: A Way To Have Low Cost Space Missions For The Unordinary Innovator, Robert J. Twiggs, Amin Djamshidpour, Ted Tagami, Tony So

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Robert Twiggs, Amin Djamshidpour , Ted Tagami, and Tony So titled "Citizen Satellite: A Way to have Low Cost Space Missions for the Unordinary Innovator" from August 7, 2016.

Development Of Functional Requirements For A High-Capacity Airspace System, Noel J. Colon, Jeongjoon Boo, Steven J. Landry

The Summer Undergraduate Research Fellowship (SURF) Symposium

NASA along with other researchers visualizes a future where more aircraft will transport passengers or goods around the world. Thus, they envision increasing air capacity from 10 to 100 times more than the current system without any reduction in efficiency or safety. Many models are being proposed that comply with the necessary requirements to form part of the method needed. However, knowing which of the proposed methods have the most desirable characteristics, such as efficiency and safety, are yet to be determined. For this reason, a standardized method to compare and assess them has to be developed, since is not …

Evaluation Of Strain Distortion Correction Protocol Using Scanning Electron Microscopy And Digital Image Correlation, Alexandra Mallory, Alberto Mello, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

Scanning electron microscopy in combination with digital image correlation (SEM-DIC) is a useful technique for measuring strain in materials at the micro-scale. In particular, it can be used to identify micro-scale strain localizations that are the precursor to material failure. While SEM produces high resolution images of the microstructure, the images also contain a large amount of distortion that, during DIC, will result in distorted strain values that require correction. In this project, a nickel-based alloy underwent cyclic mechanical fatigue at three different high temperatures to a targeted maximum strain. Scanning electron microscopy imaging was done on a 200x150μm area …

Metamodels Of Residual Stress Buildup For Machining Process Modeling, Stuart B. Mccrorie, Michael Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the process of machining materials, stresses, called residual stresses, accumulate in the workpiece being machined that remain after the process is completed. These residual stresses can affect the properties of the material or cause part distortion, and it is important that they be calculated to prevent complications from arising due to the residual stresses. However, these calculations can be incredibly computationally intensive, and thus other methods are needed to predict the residual stresses in materials for quick decision-making during machining. By using metamodels - a method of representing data where few data points exist - we can achieve an …