Aerospace Engineering Commons^™

Comparison Of Flow Field In The Proximity Of A Single Planar & Wrap-Around Fin, Nayhel Sharma, Palak Saini, Hrishabh Chaudhary, Gurteg Nagi, Rakesh Kumar Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Abstract

This paper analyses the results of the computational analysis between a single planar and a wrap-around fin mounted on a semi-cylindrical body. A free-stream Computational Fluid Dynamics (CFD) model was simulated for both cases in the Mach 0.4-3.0M range at 0°Angle of attack, in which, the behavior of flow around the fin was investigated using a turbulence model of higher order discretization. The post-processing shows all the possible views of the flow dynamics around the fins, as well as the missile body. The aerodynamic drag and the rolling moment characteristics of the planar and the wrap-around fin have been …

Design And Realization Of An Unmanned Aerial Rotorcraft Vehicle Using Pressurized Inflatable Structure, Nirmal Sadasivan

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned aerial rotorcraft vehicles have many military, commercial and civil applications. There is a necessity to advance the performance on several ranges of rotorcraft for using these vehicles successfully in the expanded future roles. A lower flight time, noise disturbance and safety issues remain the key obstacles in increasing the efficiency of the rotorcraft for various applications. This work presents the design and realization of a rotorcraft using pressurized inflatable structure filled with lighter than air gas such as helium or hydrogen to provide lift assistance for the vehicle. Two iterative design procedures were developed for designing the vehicle. One …

A Comparative Aerodynamic Study Of Nonplanar Wings, Mondher Yahyaoui

International Journal of Aviation, Aeronautics, and Aerospace

In this work four nonplanar wing configurations were studied using the vortex-lattice method: the wing-winglet, the C-wing, the biplane, and the box wing. It has been shown that linear twist, which is more practical in aeronautical construction, is more than adequate to achieve the higher values of span efficiency factor obtained by a completely optimized twist distribution along the span camber, the latter being in general highly varying and thus not very practical. It has also been shown that moderate sweep can slightly increase the span efficiency factor and further reduce vortex drag. The increase is more important for the …

Double Stud Cargo Fitting Research, Alternative Cargo Clip Design And Analysis, Cemal İrfan Çalişkan, Ebubekir Koç Dr, Hamaid Mahmood Khan Dr, Mustafa Enes Bulduk

International Journal of Aviation, Aeronautics, and Aerospace

It can be said that today's civil aviation basics began to be laid in the 1950s. This date is also important as the period in which the rules are being written and at the same time, some system solutions are produced by testing the methods of cargo loading. The cargo clip used in these cargo loading systems will be the subject of our article. In this context, the development process of the clip, which started in 1953 until today, will be examined in the light of the patent applications of the period; Afterwards, alternative clip-on work to the current cargo …

Design Guidelines For Supersonic Aircrafts In Civil Aviation, Tridib Banerjee Mr.

International Journal of Aviation, Aeronautics, and Aerospace

There exists no publication currently available to the scholars that address in detail, every aspect of designing a modern supersonic aircraft for civil aviation. This paper aims to resolve that issue. It reviews all the existing work that has been done on the topic so far and builds upon that. It incorporates multiple disciplines and takes into account the closely inter-coupled effects of each component on one-another. It also analyses in detail the various environmental and modern regulatory challenges like sonic boom and means to overcome them. It further addresses the challenges like logistics, cabin crew radiation exposure, and cost …

Simulations On Optimization Of Liquid Spray Burners & Operating Parameters, Pallavi Gajjar, Vinayak Malhotra

International Journal of Aviation, Aeronautics, and Aerospace

Spray burners form an essential part of any liquid propulsion system as they are responsible for injecting, atomizing, mixing and combusting the liquid fuel. Spray combustion used in aerospace applications like the liquid rocket engines, gas turbines or any other controlled environment for that matter places a huge emphasis on safe and effective operations. These applications make use of relatively small amounts of propellant volumes to generate enormous amounts of energy through combustion for producing thrust. For such cases involving enormous energy interactions, combustion comes with its own set of challenges. The predominant challenge among them all is that of …

Design And Simulation Of Regional Navigation Constellation With Optimized Mean Dop Based On Hybrid Geo And Igso Satellites, Firooz Keyvani, Seyed Hosein Torabi

International Journal of Aviation, Aeronautics, and Aerospace

In this article, achieving an optimal layout of satellite constellation has been investigated with the aim of navigation (positioning) and with the least amount of error in a region coverage. In navigation, a parameter defined as DOP specifies influences of the geometry of satellite placement in space on position error. Less DOP means more precise navigation, and an attempt has been made in this study to minimize it. In the optimization phase, using genetic algorithm, the number of moments in which coverage is less than four reached zero and then the DOP parameter was minimized. Subsequently, the issue was studied …

Dual Graphene Patch Antenna For Ka Band Satellite Applications, Mohammed Amin Rabah, Mohammed Bekhti

International Journal of Aviation, Aeronautics, and Aerospace

Currently; grapheme offers a new opportunity to use in space technology and this is due to its amazing properties like conductivity, strength, flexibility and transparency which allows us to exploit new generation of ultra-fast nanoscale components; Since future wireless communication techniques are geared towards the use of the high frequency spectrum and many recent research prove this trend. This letter presents a proposal for design of a dual graphene-based antenna to use in new communication techniques in Ka band, where the proposed antenna can work for uplink and dowlink frequencies at same time since it has return loss less then …

Cybersecurity Planning For Artificial Intelligent Systems In Space, Gary Langford, Lucas Beaulieu, Jeffery Carpenter, Ian Watkins, Brock Marsh, Teah Heidorn, Chris Chase

Engineering and Technology Management Faculty Publications and Presentations

CubeSats continue to proliferate and are an excellent low-cost method of remote sensing. A key piece of intelligent systems is sensory input, data storage, and data communications. With the continued miniaturization of technology, CubeSats will increase their sensory inputs with future miniaturization and enhance their robustness for autonomous operations if data and communications are secure. These futures inspire an intelligent system solution to on-orbit communications. This paper explores a dual-microprocessor approach to improve hardware cybersecurity of intelligent systems, with a view toward intensional intelligence as a means of adjudicating access to sensitive data onboard the CubeSat. With enhanced cybersecurity, Artificial …

Algorithms And Optimal Control For Spacecraft Magnetic Attitude Maneuvers, Mohammed Desouky

Dissertations, Master's Theses and Master's Reports

This study focused on providing applicable control solutions for spacecraft magnetic attitude control system. Basically, two main lines are pursued; first, developing detumbling control laws and second, an improvement in the three-axis attitude control schemes by extending magnetic rods activation time.

Spacecraft, after separation from the launching mechanism, experiences a tumbling phase due to an undesired angular momentum. In this study, we present a new efficient variant of the B-dot detumbling law by introducing a substitute of the spacecraft angular velocity, based on the ambient magnetic field data. This B-dot law preserves the orthogonality, among the applied torque, dipole moment …

Gnss/Lidar-Based Navigation Of An Aerial Robot In Sparse Forests, Antonio C. Chiella, Henrique N. Machado, Bruno O.S. Teixeira, Guilherme A.S. Pereira

Faculty & Staff Scholarship

Autonomous navigation of unmanned vehicles in forests is a challenging task. In such environments, due to the canopies of the trees, information from Global Navigation Satellite Systems (GNSS) can be degraded or even unavailable. Also, because of the large number of obstacles, a previous detailed map of the environment is not practical. In this paper, we solve the complete navigation problem of an aerial robot in a sparse forest, where there is enough space for the flight and the GNSS signals can be sporadically detected. For localization, we propose a state estimator that merges information from GNSS, Attitude and Heading …

Conceptual Design Of Male Uavs, Vincent Spada

Graduate Theses, Dissertations, and Problem Reports (ETD)

The conceptual design process of aircraft involves the creation of a product, in this case UAVS (unmanned aerial vehicles), using the most effective means possible across multiple subdisciplines of Aerospace Engineering. This paper will outline a unique methodology that involves calculating certain design variables such as wing loading, power loading, aspect ratio and cruise altitude in the conceptual design phase for MALE (medium altitude long endurance) UAVs. Aircraft characteristics from MALE UAVs such as the MQ-9 predator and MQ-1 reaper will used for a comparative aircraft study as “jumping off” points in order to carry out the initial calculations. An …

Utilization Of Scale In Keypoint Detection And Feature Description, Andrew P. Rhodes

Graduate Theses, Dissertations, and Problem Reports (ETD)

Ubiquitous availability of inexpensive three dimensional (3D) sensors has led to an abundance of keypoint detection and feature description techniques for point-clouds. While some recent methods utilize color along with geometric information, most only implicitly discuss -- if not completely disregard -- the information provided by scale. Scale is an inherent characteristic of any keypoint or feature that describes its physical size or region of support.

Exploiting information provided by scale facilitates the processes of keypoint detection and feature description. A 3D scale-space, extended from robust and popular 2D methods, is constructed to diffuse a signal on triangulated meshes. Methods …

Enabling Robust State Estimation Through Covariance Adaptation, Ryan Magnum Watson

Graduate Theses, Dissertations, and Problem Reports (ETD)

Several robust state estimation frameworks have been proposed over the previous decades. Underpinning all of these robust frameworks is one dubious assumption. Specifically, the assumption that an accurate a priori measurement uncertainty model can be provided. As systems become more autonomous, this assumption becomes less valid (i.e., as systems start operating in novel environments, there is no guarantee that the assumed a priori measurement uncertainty model characterizes the sensors current observation uncertainty).

In an attempt to relax this assumption, a novel robust state estimation framework is proposed. The proposed framework enables robust state estimation through the iterative adaptation of the …

Scaling Analysis And Experimental Investigation Of A Rotating Detonation Engine, David Thomas Billups

Graduate Theses, Dissertations, and Problem Reports (ETD)

Pressure gain combustion (PGC) technologies, specifically rotating detonation engines (RDEs), are poised to provide the next big leap in gas turbine engine advancement, significantly increasing the thermal. RDEs make use of thermodynamic advantages of isochoric as opposed to isobaric combustion. Theorized to increase thermal efficiency by up to 7% [1], the RDE would have significant impact on reducing anthropogenic carbon emissions. In addition to efficiency gains, the RDE also provides mechanical simplicity and reduced size advantages compared to it’s traditional counterparts and PGC competition.

The United States (U.S.) Department of Energy (DOE) National Energy Technology Laboratory (NETL) maintains and operates …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Space Dynamics Laboratory Payload Challenge: Autonomous Water Sampling Uav, Thomas Wheeler, Zachary Williams, Joseph Stack

Williams Honors College, Honors Research Projects

The following report has been completed over the course of the Fall 2018 and Spring 2019 semesters at The University of Akron by Joseph P. Stack (Aerospace Systems Engineering), Thomas J. Wheeler (Mechanical Engineering) and Zachary M. Williams (Mechanical Engineering). The purpose of this project was to create a payload system for the Akronauts Rocket Design Team to use at the Intercollegiate Rocket Engineering Competition (IREC) Spaceport America Cup. The Competition as a challenge that is sponsored by Space Dynamics Laboratory specifically regarding payload systems. The challenge in very open-ended and allows student to identify their own scientific experiment and …

Prototype Landing Gear Conceptual And Embodiment Design, Derek Carr

Williams Honors College, Honors Research Projects

Collin’s Aerospace Mechanical systems engineering was tasked with designing a set of landing gear for an undisclosed project. The landing gear is required to comply with customer specifications, coordinate systems, and overall landing gear performance. The purpose of this project is to document the conceptual and embodiment design process for an articulated main landing gear system. Unfortunately, due to high expenses and high lead times required for 300M stainless steel components, no full size prototype can be produced within the timeframe of this report. Instead, this document should be viewed as a process mapping guide for initial landing gear design …

Blended Wing Design Considerations For A Next Generation Commercial Aircraft, Jay Abhilash Vora

Browse all Theses and Dissertations

The current aircraft design has not changed significantly in the last few decades. Growing environmental concerns and fuel prices are driving manufacturers to develop unconventional but efficient aircraft configurations. The blended wing body (BWB) configuration provides an alternate and more efficient means of subsonic travel. The BWB aircraft replaces the traditional wings and fuselage with hybrid wing shape where the fuselage and wings have integrated. Major aircraft manufacturers are researching the BWB concept incorporating electric propulsion for civil transport use. In this research a 300 passenger BWB aircraft aerodynamic shape is designed. This aircraft is used to assess the aerodynamic …

Swat Operations Unmanned Vehicle, John K. Zelina, Tyler Meadows, Ryan Cook, Mathew Fellows

Williams Honors College, Honors Research Projects

During SWAT operations, it is common to have a barricaded suspect who may be armed and a serious threat to SWAT team personnel. In these cases, sending a robot into harm's way to assess the situation as opposed to an operator has become the standard. The purpose of this of this research was to design and develop an unmanned system for the City of Akron's SWAT Team that can be injected into these scenarios to improve outcomes and mitigate risk to SWAT operators.