Propulsion and Power Commons^™

Modeling Of Rotor Wake Vortex Dynamics And Interactions In Non-Homogenous Vertiport Environments, Garrison P. Shaw

Doctoral Dissertations and Master's Theses

The current research serves to analyze and study the effects ground forces can have on the thrust performance of a propeller in multiple different configurations. The current research utilizes an open source Computational Fluid Dynamics (CFD) software known as OpenFOAM to generate calculate and visualize these runs. The model used for this experiment is a hybrid model that employs both a Unsteady Reynolds-Averaged Navier-Stokes (URANS) and a detached eddy simulation using a hybrid Large Eddy Simulation (LES) via a KomegaSSTDDES model. This model serves to save computational time as well as allow for accurate results. The three cases run are …

Rapid Response Satellite Launcher, Nathan Jones, Joey Cosentino, Jayson Layton, Afek Adar

Senior Design Project For Engineers

Air launch to orbit is a new style or spacecraft where rockets are attached to a large aircraft and released at cruising altitude to then ignite and launch into space. Companies such as Virgin Orbit are using it as a cheap and efficient way to move satellite payloads into lower or upper Earth orbit. These styles of launchers can be designed to be much smaller than ground-launched spacecraft, reducing cost and weight of the launcher in comparison. With many private companies coming into the space and satellite industry, the design and manufacturing of these launchers have become a focus within …

A Study Of Varying Dielectric Constant And Thickness Of Dielectric Barrier Discharge Devices And Their Subsequent Plasma Actuation, Sharon Kardasz

Mechanical Engineering Undergraduate Honors Theses

The principles of air-breathing ion propulsion are relatively unestablished in the aerodynamic realm as traditional forms of combustion for propulsion systems have remained in use. However, due to increasing environmental, economic, and efficiency concerns of traditional combustion, interests in innovative propulsion methodologies, such as electric propulsion, are emerging. A primary technology of interest for use of ion propulsion is the Dielectric Barrier Discharge Device (DBD). Preliminary research conducted at the University of Arkansas has determined the most favorable DBD geometry. This work will continue the preliminary research to decipher the most favorable DBD configuration by varying dielectric thickness and dielectric …

Benchmarking Of A Sco2 Heat Exchanger Flow Loop, David Velasco

Doctoral Dissertations and Master's Theses

Heat transfer of supercritical carbon dioxide (sCO2) was studied experimentally by commissioning a sCO2 flow loop featuring a horizontal tube-in-tube counterflow heat exchanger with a circular cross section. The main objective was to establish experimental heat transfer research capabilities for sCO2 at Embry-Riddle Aeronautical University’s (ERAU) Thermal Science Lab. sCO2 experiences a drastic change in thermophysical properties near its critical point that results in unique heat transfer characteristics. The high pressures at which sCO2 exists make the large gradients in thermophysical and transport properties difficult to study, experimentally and numerically. However, understanding the heat transfer characteristics and thermophysical behavior of …

Mitigating Engine Unstart In Scramjets With Porous Bleeders, Ryan Lindley

Doctoral Dissertations and Master's Theses

The effectiveness of porous bleeders in mitigating unstart phenomena and enhancing isolator effectiveness in a hypersonic scramjet was investigated. Through computational fluid dynamics simulations, the impact of porous bleeder design parameters such as pressure jump coefficient and bleeder size on isolator effectiveness and unstart prevention was evaluated. Results indicated that porous bleeders delayed flow separation and reduced adverse pressure gradients, thereby enhancing isolator performance. Additionally, porous bleeders demonstrated promising capabilities in preventing full unstart events and mitigating oscillatory unstart phenomena.

Experimental Analysis Of The Integrated High-Lift Propulsor, Robert W. Deters, Byron Ward, Shreyas Narsipur

Publications

Wind tunnel testing was conducted to evaluate the performance of the Integrated High Lift Propulsor (IHLP), a novel Distributed Electric Propulsion (DEP) system. The IHLP integrates traditional Krueger flap/slat elements with a Distributed Electric Propulsion design, enhancing high lift performance and cruise efficiency compared to conventional pylon-mounted DEP configurations. Starting from a baseline configuration determined from pretest Computational Fluid Dynamics (CFD) analyses, a parametric study was performed to determine the influence on the aerodynamic characteristics (𝐶𝑙 , 𝐶𝑥, and 𝐶𝑚). The study involved variations in flap settings, slat angles, overlap, propeller tilt, and propeller position. The impact of Reynolds number, …

Aerothermodynamic Analysis Of A Linear Aerospike Fueled With Liquid Methane Using Cfd, Aidan Rowell

Honors College Theses

Renewed interest in manned spaceflight, mostly spurred by the advancement of commercial spacecraft, has led to growing interest in improving the efficiency of rocket engines. Aerospike nozzles have the potential to provide this boost in efficiency to spacecraft and thus lower costs and increase payload capacity. This type of nozzle is what is known as altitude adjusting and can significantly increase efficiency. When paired with propellants such as methane/oxygen, which can be manufactured in-situ on some planetary bodies and has a higher density than traditional propellants like liquid hydrogen/liquid oxygen, even more efficiency gain can be achieved. To understand the …

Comparative Evaluation Of Propulsive Power Transmission Technologies For High-Speed Vertical Takeoff And Landing (Hsvtol) Cargo Aircraft, Xinyu Yang

Doctoral Dissertations and Master's Theses

Designing High-Speed Vertical Takeoff and Landing (HSVTOL) cargo aircraft capable of both low downwash velocity hovering and high subsonic speed cruising presents a significant engineering challenge. This challenge, stemming from conflicting design requirements, has been substantially influenced by recent technological advancements, which have offered greater flexibility in rotor placement. Consequently, this has led to the emergence of innovative mission-specific designs that hold the potential to outperform traditional concepts. The central objective of this study is to evaluate the benefits of modern technologies for VTOL cargo aircraft and assess their performance relative to baseline VTOL aircraft. The results of this comparative …

Analysis Of An Electrospray Thruster With A Concave Propellant Meniscus, Adam Nicholas Huller

Masters Theses

The low thrust, high specific impulse, and low mass of electrospray thrusters (ETs) make them ideal for maneuvering nanosatellites, especially with the new requirement to deorbit a satellite within five years of completing its mission. These innovative thrusters use electrohydrodynamic principles of electrospray (ES) to provide thrust. These principles have been subject to much research over the past decade, though much more research is needed to fully understand the underlying physics of these thrusters. The first part of this study establishes a procedure for analyzing the theoretical thrust performance of an ET, by using propellant properties and well-documented ES scaling …

Testing And Implementation Of Attitude Determination & Control System For Arksat-1 Cubesatellite, Cassandra Sands

Graduate Theses and Dissertations

ARKSAT-1 is a CubeSatellite (CubeSat) developed at the University of Arkansas and launched to the International Space Station on SpaceX mission SPX-27 launching from Kennedy Space Center as part of the NASA’s 8th CubeSat Launch Initiative CSLI-8. ARKSAT-1’s payload features a high-powered LED, the Solid State Inflatable Balloon (SSIB) deorbiting system applicable to small satellites, and a series of InfraRed and Visible cameras. To point the LED or take images of desired observational targets, the spacecraft will need to be able to determine its orientation within its orbit, as well as rotate. This will be achieved through the use of …

Kwad - Ksu All Weather Autonomous Drone, Nick Farinacci, Sebastian Gomez, Stewart Baker, Ed Sheridan

Symposium of Student Scholars

"KWAD" or "KSU all-Weather Autonomous Drone" project was sponsored by Ultool, LLC to the KSU Research and Service Foundation to create a lightweight drone capable of capturing HD video during all-weather operations. The conditions of all-weather operation include rainfall of one inch per hour and wind speeds of up to twenty miles per hour. In addition, a global minimum structural safety factor of two is required to ensure the system's integrity in extreme weather conditions. Potential mission profiles include autonomous aerial delivery, topological mapping in high moisture areas, security surveillance, search and rescue operations, emergency transportation of medical supplies, and …

Design And Implementation Of A Launching Method For Free To Oscillate Dynamic Stability Testing, Kristen M. Carey

Mechanical & Aerospace Engineering Theses & Dissertations

Magnetic Suspension and Balance Systems (MSBS) allow for static, forced oscillation and free to oscillate dynamic stability testing in a wind tunnel without the need for a physical support. The objectives of study are to assist in the application of the free to oscillate testing method in an MSBS to determine dynamic stability characteristics for various re-entry capsule designs.

This thesis discusses the development and testing of a launching method called the grabber for use in the MSBS Subsonic Wind Tunnel at NASA Langley Research Center. Aerodynamic tests were run to support the use of this method and compare the …

Performance And Emissions Study Of N+3 And N+4 Engine Models With Several Fuel Types Using Npss, Abel Solomon

McKelvey School of Engineering Theses & Dissertations

The aviation industry is known to be one of the major contributors to greenhouse gases accounting for 4.9% of the global greenhouse emissions. With the ever-increasing threat of climate change to the overall survival of the planet, the exploration of new technologies and alternative energy sources that minimize greenhouse gas emissions are of paramount importance. In this regard, the development of propulsion systems well suited for the performance and emissions requirements of future commercial aircraft plays a crucial role. This thesis investigates N+3 and N+4 technology-level propulsion systems that are proposed by NASA as possible propulsion systems for advanced single-aisle …

Performance Evaluation And Thermal Management Solutions For A Sustainable Microsized Hydrogen-Powered Turbo-Shaft Engine, Nikolai Baranov

Discovery Undergraduate Interdisciplinary Research Internship

Analyzing the aerospace and automotive industries, there is a transition to sustainable energy generation. Aiming to bridge industrial emissions with the worldwide net zero goal by 2050, one widely considered solution for long-range drones and small aircraft is compact turbo-shaft engines combusting clean hydrogen gas to produce shaft work. The small size and energy-dense fuel allow for a universal powerplant with high specific power output that fits a wide variety of existing solutions. One such micro-sized turboshaft internal combustion engine was created to test the potential power output, thermal management, and combustor optimization of the existing stainless steel assembly. The …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

Crazyflie 2.1 Quadcopter Nonlinear System Identification, Nhat V. Nguyen, Hope Storro, John Plimpton

2023 Symposium

Quadcopters (quad) are used widely in many industries with crucial applications such as infrastructure inspection or package delivery. The Crazyflie 2.1 quad from Bitcraze provides an excellent platform for research and development. In this project, our goal is to perform system identification on the Crazyflie to propose a complete model. A gray box method is explored, which includes leveraging the parameters that are already known, to develop a set of equations. Through theory, simulations, and measurements, a complete quadcopter model is developed.

Cooled Liquid Rocket Thrust Chamber, Benjamin Gibson, Kealan Frederick Harris, Ryan Frank Schackel, Bjorn Thorsen

Mechanical Engineering

Cooling may affect the thrust output of a small-scale rocket. Little research is published about small-scale rocket performance. We hypothesize the thrust produced varies as the amount of cooling varies. To facilitate assessing this hypothesis, we have designed and built a liquid rocket engine rated for at approximately 25 lb_f of thrust. Our objective was to build in parallel with Cal Poly Space Systems, who built a rocket engine with similar specifications except without cooling. Our challenge is to integrate film cooling, so that the effects of cooling may be compared to Cal Poly Space System’s engine which has …

Feasibility Assessment Of An All-Electric, Narrow-Body Airliner, Ariel Sampson

Master's Theses

Combustion emissions from aviation operations contribute significantly to climate change and air pollution. Accordingly, there is increasing interest in advancing battery-powered propulsion for aviation applications to reduce emissions. As batteries continue to improve, it is essential to recognize breakthroughs in battery specific energy in the context of air transport vehicles. Most electric aircraft designs and programs have focused on small aircraft because of restrictive battery performance. This work presents a feasibility assessment for an all-electric airliner based on an Airbus A220-100 with turbofan engines replaced by electric motors and propellers. The analysis compares the performance characteristics of the electric airliner …

Design And Implementation Of High-Efficiency, Lightweight, System-Friendly Solid-State Circuit Breaker, Dehao Qin

All Dissertations

Direct current (DC) distribution system has shown potential over the alternative current (AC) distribution system in some application scenarios, e.g., electrified transportation, renewable energy, data center, etc. Because of the fast response speed, DC solid-state circuit breaker (SSCB) becomes a promising technology for the future power electronics intensive DC energy system with fault-tolerant capability. First, a thorough literature survey is performed to review the DC-SSCB technology. The key components for DC-SSCB, including power semiconductors, topologies, energy absorption units, and fault detection circuits, are studied. It is observed that the prior studies mainly focus on the basic interruption capability of the …

Enabling Premixed Hydrogen-Air Combustion For Aeroengines Via Laboratory Experiment Modeling, Christopher James Caulfield

Masters Theses

All combustion systems from large scale power plants to the engines of cars to gas turbines in aircraft are looking for new fuel sources. Recently, clean energy for aviation has come into the foreground as an important issue due to the environment impacts of current combustion methods and fuels used. The aircraft industry is looking towards hydrogen as a new, powerful, and clean fuel of the future. However there are several engineering and scientific challenges to overcome before hydrogen can be deployed into the industry. These issues
range from storing the hydrogen in a viable cryogenic form for an aircraft …