Ocean Engineering Commons^™

A Wedge Impact Theory Used To Predict Bow Slamming Forces, Ashok Benjamin Basil Attumaly

University of New Orleans Theses and Dissertations

The pressures and impact forces acting on a hull while experiencing bow wave slamming is analyzed using Vorus' Impact Theory. The theory extends the hydrodynamic analysis of planing hulls from simple wedges to irregular shapes using a Boundary Element Method. A Fortran-based code developed by the Author is used to analyze hullforms. Linear strip theory is used to extend the analysis over a three dimensional hull. Post-processing of output data gives hull pressure distributions at different time steps and is visually presentable.

Impact pressure, Impact force, Planing, Wave slamming, Bow impact, Vorus' theory, Boundary Element Method, Linear strip theory

Semiconductor Thermal Neutron Detector, Toru Aoki, Aki Miyake, Takayuki Nakano, Akifumi Koike, Hisashi Morii, Hidenori Mimura

Makara Journal of Technology

The CdTe and GaN detector with a Gd converter have been developed and investigated as a neutron detector for neutron imaging. The fabricated Gd/CdTe detector with the 25 mm thick Gd was designed on the basis of simulation results of thermal neutron detection efficiency and spatial resolution. The Gd/CdTe detector shows the detection of neutron capture gamma ray emission in the 155Gd(n, g)156Gd, 157Gd(n, g)158Gd and 113Cd(n, g)114Cd reactions and characteristic X-ray emissions due to conversion-electrons generated inside the Gd film. The observed efficient thermal neutron detection with the Gd/CdTe detector shows its promise in neutron radiography application. Moreover, a …

The Effect Of Pressing Temperature And Time On The Quality Of Particle Board Made From Jatropha Fruit Hulls Treated In Acidic Condition, Apri Heri Iswanto, Fauzi Febrianto, Yusuf Sudo Hadi, Surdiding Ruhendi, Dede Hermawan

Makara Journal of Technology

The high of pH of jatropha fruit hulls causes the negative properties of particleboard made from this material. Adjusting the particle acidity and pressing conditions (temperature and time) is among the technical modifications available to improve this particleboard’s properties. Particle acidity has been adjusted in a previous research project, and immersing the particles in acetic acid was found to be the best treatment in this preliminary research. In order to improve the particleboard’s properties, an experiment was conducted to determine the best pressing temperature and time. The objective of the research was to evaluate the influence of pressing temperature and …

Radiation Characteristics Of A Planar Strip Dipole Antenna And A Slot Dipole Antenna For Thz Applications, Catur Apriono, Eko Tjipto Rahardjo

Makara Journal of Technology

The development of a THz system often requires a device that is used to radiate or detect THz waves. One way to fulfill this requirement is to use an antenna. Therefore, we need to consider the radiation characteristics of an antenna working in the THz region. In this paper, we present simulation study of two dipole antennas, i.e. a planar strip dipole antenna and a slot dipole antenna. The simulation results show that a planar strip dipole antenna has a better radiation efficiency (more than 95%) compared to the slot dipole. It also shows that an efficiency of more than …

Synthesis Of Tungsten Oxide Nanowires Onto Ito Glass Using T-Cvd, Tomy Abuzairi, Bohr-Ran Huang, Tzu-Ching Lin

Makara Journal of Technology

Tungsten oxide is an n-type semiconductor with interesting physical and chemical properties that make it suitable for various technological applications. Tungsten oxide nanowires were synthesized not only at low temperature but also without the use of any catalysts. The tungsten oxide nanowires were synthesized at 550 °C with tungsten layers onto the ITO glass using thermal chemical vapor deposition (T-CVD). The SEM image shows that the tungsten oxide nanowires are effectively grown with the 200 nm tungsten film. The Raman spectra shoulder at ~690 cm-1 proves the synthesized of tungsten oxide nanowires.

Microgrid Development Using A Grid Tie Inverter, Hartono Budi Santoso, Budiyanto Budiyanto

Makara Journal of Technology

The use of renewable energy sources (RES), especially photovoltaic (PV), to meet the demand of electrical energy has been getting a great deal of attention as an alternative solution to electrical energy deficit problems. RES are being applied in power systems in a variety of configurations including microgrid systems. One of the characteristics of a microgrid is capability to supplying power to grid when there is an excess power to supply local load. This research examines the chances of saving power consumption from grid using power converters grid tie inverter (GTI) in a microgrid configuration. The test is done by …

Recycling Roof Tile Waste Material For Wall Cover Tiles, Ambar Mulyono, Silfia Mona Aryani, Joko Lulut

Makara Journal of Technology

Prior research on roof tile waste treatment has attempted to find the appropriate technology to reuse old roof tile waste by create wall cladding materials from it. Through exploration and experimentation, a treatment method has been discovered to transform the tile fragments into artificial stone that resembles the shape of coral. This baked clay artificial stone material is then processed as a decorative element for vertical surfaces that are not load-bearing, such as on the interior and exterior walls of a building. Before applying the fragments as wall tiles, several steps must be taken: 1) Blunting, which changes the look …

Surface Treatment Of Fly Ash For Improving The Tensile Strength Of Fly Ash/Unsaturated Polyester Composites, Sugiman Sugiman, Paryanto Dwi Setyawan

Makara Journal of Technology

The paper presents the surface treatment of fly ashes using acid and alkali solution on the tensile strength of the fly ash/unsaturated polyester (UP) composites. Sulfuric acid (H2SO4), hydrofluoric acid (HF) and sodium hydroxide (NaOH) solution with concentration of 0%, 5%, 10%, 15%, and 20% (by weight) were used for surface treatment of fly ashes. Generally, the tensile strength of the treated fly-ash/UP composites shows a significant increase compared to the untreated fly ash. Of all surface treatments studied, the optimum tensile strength was obtained at a concentration of 10%. At this concentration, at a fly ash content of 30% …

Nineteenth Century North American And Pacific Tidal Data: Lost Or Just Forgotten?, Stefan A. Talke, David A. Jay

Civil and Environmental Engineering Faculty Publications and Presentations

Tide data are the oldest and longest oceanographic records and comprise one of the few tools for understanding, quantifying, and separating century-scale human and climate impacts on the coastal zone. Our archival research indicates that continuous measurements of tides began in 1844 in the western Atlantic, 1853 in the Eastern Pacific, and 1858 in the Western Pacific. At least 50 multiyear tide series existed by the year 1900. With few exceptions, however, these 19th and early 20th century measurements have not been analyzed in more than a century and have been forgotten and neglected by the scientific community. This article …

Dimensionless Criteria For Selecting Tidally-Influenced Advective-Dispersive Desalination Brine Mixing Plume Characterization Models, Alireza Shahvari

Civil & Environmental Engineering Theses & Dissertations

The very nature of requirements for implementing a desalination process is highly spatial due to the need to secure both a source for the operation and sink for brine dilution. Thus, the applicable coastal location is bound to natural tidal mixing characteristics and subjected to a near- or a far-field availability for source and sink. Mixing characteristics of coastal waters are very different from one point to another due to the spatiotemporal tidal characteristic in loco in a manner that it can vary from being highly advective to completely dispersive dominant. Once a location is identified, estimation of corresponding water …

The Effect Zeolite Addition In Natural Rubber Polypropylene Composite On Mechanical, Structure, And Thermal Characteristics, Nurdin Bukit, Erna Frida

Makara Journal of Technology

This study was conducted to determine the effect of zeolite as filler on mechanical properties, and thermal structure blends of natural rubber and polypropylene (NR/PP). In this study, NR/PP/PP-g-MA blends was filled uncalcined zeolite and calcined zeolite at different weight percent of the 2, 4, and 6%. Samples were characterized to determine the tensile strength, fracture elongation and Young's modulus. Structure of the samples was investigated using XRD method and thermal characteristics were analyzed using DTA/TGA technique. The results obtained for tensile strength showed a significant influence with the addition zeolite of the NR/PP blends at 2% by weight of …

Influences Of Surface Morphology Of Nanostructured Rutile Tio2 Nanorods/Nanoflowers As Photoelectrode On The Performance Of Dye-Sensitized Solar Cell, Mohd Khairul Bin Ahmad, Kenji Murakami

Makara Journal of Technology

Aligned Rutile TiO2 nanorods (r-TNRs) and TiO2 nanoflowers (r-TNFs) were successfully prepared by hydrothermal method. Using hydrochloric acid (HCl) as chelating agent and titanium butoxide (TBOT) as precursor, aligned r-TNRs with r-TNFs were successfully growth onto fluorine-doped tin oxide (FTO) with different morphologies. The influences of surface morphologies to the rutile based Dye-sensitized solar cell (DSC) efficiency are discussed. The highest lightto- electric energy conversion efficiency, 1.80% is achieved using different concentration under simulated solar light illumination of 100 mWcm-2 (1.5 AM).

Determining The Air Gap Length Of An Axial Flux Wound Rotor Synchronous Generator, Abdul Multi, Iwa Garniwa, Uno Bintang Sudibyo

Makara Journal of Technology

The air gap length of the designed axial flux wound rotor (AFWR) synchronous generator is determined properly according to the design parameters. One of the distinct advantages of an axial flux (AF) machine is its adjustable air gap. An AF generator’s performance might be controlled by adjusting its air gap. The designed generator has a smallscale capacity that has 1 kW, 380 V, and 50 Hz. The windings are laid into slots made from laminated core. The slots are carved in the face of the stator and rotors. The generator has a single-double-sided slotted wound stator sandwiched between twin rotors. …

Production Optimization For Plan Of Gas Field Development Using Marginal Cost Analysis, Suprapto Soemardan, Widodo Wahyu Purwanto, Arsegianto Arsegianto

Makara Journal of Technology

Gas production rate is one of the most important variables affecting the feasibility plan of gas field development. It take into account reservoir characteristics, gas reserves, number of wells, production facilities, government take and market conditions. In this research, a mathematical model of gas production optimization has been developed using marginal cost analysis in determining the optimum gas production rate for economic profit, by employing the case study of Matindok Field. The results show that the optimum gas production rate is mainly affected by gas price duration and time of gas delivery. When the price of gas increases, the optimum …

Characteristics Of Vacuum Freeze Drying With Utilization Of Internal Cooling And Condenser Waste Heat For Sublimation, Muhammad Idrus Alhamid, Nasruddin Yusuf, Indra Teuku Meurah Mahlia, Engkos Ahmad Kosasih, Muhamad Yulianto, Rio Ricardi

Makara Journal of Technology

Vacuum freeze drying is an excellent drying method, but it is very energy-intensive because a relatively long drying time is required. This research investigates the utilization of condenser waste heat for sublimation as a way of accelerating the drying rate. In addition, it also investigates the effect of internal cooling combined with vacuum cooling in the pressure reduction process. Jelly fish tentacles were used as the specimen, with different configurations for condenser heat waste and internal cooling valve opening. The results show that heating with condenser heat waste can accelerate the drying rate up to 0.0035 kg/m2.s. In addition, pre-freezing …

The Plasma Electrolysis Phenomenon In A Two-Compartment Reactor For Chlor-Alkali Production, Nelson Saksono, Fakhrian Abqari, Setijo Bismo

Makara Journal of Technology

Chlor-alkali is one of the most important processes in the chemical industry. It produces chlorine and caustic soda, which become the main feedstock of daily products. The aim of this study is to report the phenomenon of plasma electrolysis and how it can be used in chlor-alkali production for more efficient energy consumption. When the plasma is formed, the current fluctuates and gradually declines. Plasma electrolysis begins with the process of electrolysis itself. Due to Joule heating, gas bubbles are formed and a sheath is made on both electrodes, resulting in the plasma field. Plasma electrolysis can be identified by …

Observation Of Photovoltaic Effect And Single-Photon Detection In Nanowire Silicon Pn-Junction, Arief Udhiarto, Sri Purwiyanti, Daniel Moraru, Takeshi Mizuno, Michiharu Tabe

Makara Journal of Technology

We study nanowire silicon pin and pn-junctions at room and low temperature. Photovoltaic effects are observed for both devices at room temperature. At low temperature, nanowire pn-junction devices show their ability to detect single photon. This ability was not been observed for pin devices. Phosphorus-boron dopant cluster in the depletion region is considered to have the main role for single-photon detection capability. Fundamental mechanism of dopant-based single-photon detection in nanowire pn-junction is described in details.

Fatigue Life Prediction Of The Keel Structure Of A Tsunami Buoy Using Spectral Fatigue Analysis Method, Angga Yustiawan, Ketut Suastika, Wibowo Harso Nugroho

Makara Journal of Technology

One of the components of the Indonesia Tsunami Early Warning System (InaTEWS) is a surface buoy. The surface buoy is exposed to dynamic and random loadings while operating at sea, particularly due to waves. Because of the cyclic nature of the wave load, this may result in a fatigue damage of the keel structure, which connects the mooring line with the buoy hull. The operating location of the buoy is off the Java South Coast at the coordinate (10.3998 S, 108.3417 E). To determine the stress transfer function, model tests were performed, measuring the buoy motions and the stress at …

A New Experimental Approach To Evaluate Plasma-Induced Damage In Microcantilever, Yuki Nishimori, Shinji Ueki, Masakazu Sugiyama, Seiji Samukawa, Gen Hashiguchi

Makara Journal of Technology

Plasma etching, during micro-fabrication processing is indispensable for fabricating MEMS structures. During the plasma processes, two major matters, charged ions and vacuum–ultraviolet (VUV) irradiation damage, take charge of reliability degradation. The charged ions induce unwanted sidewall etching, generally called as “notching”, which causes degradation in brittle strength. Furthermore, the VUV irradiation gives rise to crystal defects on the etching surface. To overcome the problem, neutral beam etching (NBE), which use neutral particles without the VUV irradiation, has been developed. In order to evaluate the effect of the NBE quantitatively, we measured the resonance property of a micro-cantilever before and after …

Improvement In Performance Of Zno Based Dsc Prepared By Spraying Method, Rangga Winantyo, Devinda Liyanage, Kenji Murakami

Makara Journal of Technology

This paper reports the effect of TiCl4 on the performance of ZnO based DSC. ZnO was used due to its stability against photo-corrosion and photochemical properties similar to TiO2. Thin films of nanocrystalline ZnO were deposited on transparent conducting oxide glass using spray method. The ZnO films were treated using TiCl4. The cell’s efficiency was found to be 2.5% with TiCl4 post-treatment and 1.9% without TiCl4 post-treatment.