Geological Engineering Commons^™

Overall Psd And Fractal Characteristics Of Tight Oil Reservoirs: A Case Study Of Lucaogou Formation In Junggar Basin, China, Xixin Wang, Jiagen Hou, Yuming Liu, Peiqiang Zhao, Ke Ma, Dongmei Wang, Xiaoxu Ren, Lin Yan

Geology and Geological Engineering Faculty Publications

Lucaogou tight oil reservoir, located in the Junggar Basin, Northwest of China, is one of the typical tight oil reservoirs. Complex lithology leads to a wide pore size distribution (PSD), ranging from several nanometers to hundreds of micrometers. To better understand PSD and fractal features of Lucaogou tight oil reservoir, the experiment methods including scanning electron microscope (SEM), rate-controlled mercury injection (RMI) and pressure-controlled mercury injection (PMI) were performed on the six samples with different lithology. The results indicate that four types of pores exist in Lucaogou tight oil reservoir, including dissolution pores, clay dominated pores, microfractures and inter-granular pores. …

Landsliding Near Enguri Dam (Caucasus, Georgia) And Possible Seismoectonic Effects, Alessandro Tibaldi, Paolo Oppizzi, John S. Gierke, Thomas Oommen, Nino Tsereteli, Davit Odilavadze

Michigan Tech Publications, Part 1

The Enguri dam and water reservoir, nested in southwestern Caucasus (Republic of Georgia), are surrounded by steep mountain slopes. At a distance of 2.5 km from the dam, a mountain ridge along the reservoir is affected by active deformations with a double vergence. The western slope, directly facing the reservoir, has deformations that involve a subaerial area of 1.2 km2. The head scarp interests the main Jvari-Khaishi-Mestia road with offset of man-made features that indicate slip rates of 2-9 cm/y. Static, pseudostatic and Newmark numerical analyses, based on field and seismological data, suggest different unstable rock volumes basing on the …

Slalom: An All-Surface Snow Water Path Retrieval Algorithm For The Gpm Microwave Imager, Jean-François Rysman, Giulia Panegrossi, Paolo Sanò, Anna Cinzia Marra, Stefano Dietrich, Lisa Milani, Mark S. Kulie

Michigan Tech Publications, Part 1

This paper describes a new algorithm that is able to detect snowfall and retrieve the associated snow water path (SWP), for any surface type, using the Global Precipitation Measurement (GPM) Microwave Imager (GMI). The algorithm is tuned and evaluated against coincident observations of the Cloud Profiling Radar (CPR) onboard CloudSat. It is composed of three modules for (i) snowfall detection, (ii) supercooled droplet detection and (iii) SWP retrieval. This algorithm takes into account environmental conditions to retrieve SWP and does not rely on any surface classification scheme. The snowfall detection module is able to detect 83% of snowfall events including …

Spatial And Temporal Storm Generation From A Stochastic View, Jiaxiang Ding, Josept D. Revuelta-Acosta, Engel Bernard

The Summer Undergraduate Research Fellowship (SURF) Symposium

Precipitation is one of the most important parameters in the study of hydrology and most of the research has been done on daily storm generation. Current weather generation models are used to replicate daily or monthly time resolution, which is not able to show the variability within one day or one month. This project deals with sub-daily storm generation with finer resolution and more accurate estimation, which also requires an independent storm separation method. And the Monte Carlo correlated multivariate simulation is applied to compute the variables. The description is essential for soil erosion and water quality research. Another reason …

Demonstration Of The Gas Assisted Gravity Drainage (Gagd) Process In Carbonate Rocks., Alok Jiteshkumar Shah

LSU Master's Theses

The Gas Assisted Gravity Drainage (GAGD) process was developed and patented by Dr. Rao at LSU in the early 2000s. The process involves the use of several existing or new vertical injection wells to inject gas and use the natural segregation of reservoir fluids from the density difference and the gravitational forces to displace the trapped oil and mobilize the oil downwards to be produced by a horizontal producing well. The GAGD process can be implemented as a secondary or tertiary oil recovery method. Several physical model experiments have been conducted to demonstrate the effectiveness of the GAGD process for …

Sensitivity Of Atmospheric Aerosol Scavenging To Precipitation Intensity And Frequency In The Context Of Global Climate Change, Pei Hou, Shiliang Wu, Jessica L. Mccarty, Yang Gao

Michigan Tech Publications, Part 1

Wet deposition driven by precipitation is an important sink for atmospheric aerosols and soluble gases. We investigate the sensitivity of atmospheric aerosol lifetimes to precipitation intensity and frequency in the context of global climate change. Our sensitivity model simulations, through some simplified perturbations to precipitation in the GEOS-Chem model, show that the removal efficiency and hence the atmospheric lifetime of aerosols have significantly higher sensitivities to precipitation frequencies than to precipitation intensities, indicating that the same amount of precipitation may lead to different removal efficiencies of atmospheric aerosols. Combining the long-term trends of precipitation patterns for various regions with the …

The Effect Of Wellbore Circulation On Building An Lcm Bridge At The Fracture Aperture, Ghassan Alshubbar, Runar Nygaard, Montri Jeennakorn

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Different laboratory experimental setups with slotted disks, simulating fractures' apertures, have been used extensively to formulate effective loss circulation materials (LCM) recipes. The amount of fluid loss and sealing pressure have been used as the evaluation criteria. The question still remains is how valuable these tests are when LCM fluids are circulated in the wellbore to stop losses. The main objective of this work is to study the effect of the annular fluid flow on building an LCM bridge at the fracture aperture. To address the objective, a fluid loss apparatus has been developed to mimic wellbore circulation. Tapered slotted …

The Ozone Monitoring Instrument: Overview Of 14 Years In Space, Pieternel F. Levelt, Joanna Joiner, Johanna Tamminen, J. Pepijn Veefkind, Pawan K. Bhartia, Simon Carn, Et. Al.

Michigan Tech Publications, Part 1

This overview paper highlights the successes of the Ozone Monitoring Instrument (OMI) on board the Aura satellite spanning a period of nearly 14 years. Data from OMI has been used in a wide range of applications and research resulting in many new findings. Due to its unprecedented spatial resolution, in combination with daily global coverage, OMI plays a unique role in measuring trace gases important for the ozone layer, air quality, and climate change. With the operational very fast delivery (VFD; direct readout) and near real-time (NRT) availability of the data, OMI also plays an important role in the development …

Hawai'i Wildlife Fund V. County Of Maui, Lowell J. Chandler

Public Land & Resources Law Review

In Hawai’i Wildlife Fund v. County of Maui, the Ninth Circuit held that the plain language of the Clean Water Act provides jurisdiction over indirect discharges of pollutants from a point source into groundwater that is shown to be connected to navigable waters. The court found that studies confirmed pollutants entering the Pacific Ocean were fairly traceable to the County of Maui’s sewage disposal wells. In affirming the district court’s ruling, the Ninth Circuit held that Maui County violated the Clean Water Act by discharging pollutants into a navigable water without the required permit. The court also concluded the …

Spectral Analysis Of Surface Waves To Detect Subsurface Voids, Payman Hajiani, Neil Lennart Anderson, J. David Rogers

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Systems and methods for detecting a subsurface cavity. A source applies a force to ground under inspection and a plurality of sensors coupled to the ground detect resulting surface waves. A processor is configured to extract phase and frequency components of the acquired seismic data, identify a phase shift in surface waves in the ground under inspection based on the extracted phase and frequency components, and determine one or more physical characteristics of a subsurface cavity based on the identified phase shift

Mountain Front Recharge In A Semi-Arid Climate, Southwest Montana, Charles Shama

Graduate Theses & Non-Theses

Groundwater recharge to regional valley benches originates largely from adjacent Mountain Front Recharge (MFR). The Madison Valley in Southwest Montana is a semi-arid cold climate that receives 31.75cm annual valley precipitation. In this study, two drainages are characterized and compared, looking at the hydrological processes between the stream and groundwater. North Meadow Creek is a high elevation stream dominated by snowmelt and contains reaches of gaining and losing surface water to groundwater. Daylight Creek is a spring fed disconnected stream. Methods used a surface water balance, temperature as an environmental tracer and two and three component mixing models to investigate …

Fluid Inclusion And Stable Isotope Investigation Of Hydrothermal Talc And Chlorite Deposits In Southwest Montana, Garrett Hill

Graduate Theses & Non-Theses

Talc and chlorite deposits of southwest Montana formed as hydrothermal replacements of Archean and/or early Proterozoic dolomitic marble and quartzo-feldspathic gneiss. Although the hydrothermal replacement model is generally accepted, less is known about the temperature, composition, and origin of the fluids involved in talc and chlorite formation. The present study examines fluid inclusions in quartz associated with both talc and chlorite, stable hydrogen and oxygen isotopes of talc, chlorite, and quartz, and stable carbon and oxygen isotopes of carbonate minerals. The deposits being examined include the Yellowstone, Beaverhead and Willow Creek talc mines, and the Antler chlorite mine.

Fluid inclusion …

Mineralogy And Sulfur Isotope Geochemistry Of The Apex And Bonanza Prospects At The Golden Sunlight Mine, Montana, Hamadou Gnanou

Graduate Theses & Non-Theses

The Golden Sunlight mine, located 50 km to the east of the famous Butte porphyry/lode deposits, is the largest gold mine in Montana, and has produced over 3 million ounces of gold in its 35+ year history. Most of this gold has come from the Mineral Hill breccia pipe (MHBP), a west dipping, cylindrical body of brecciated latite and country rock fragments of the Precambrian LaHood and Greyson Formations. The breccia pipe is late Cretaceous in age (84±18 Ma, DeWitt et al., 1986), is silicified, pyrite-rich, and is mineralized with gold, silver, and minor base metals. Because the MHBP has …

Uav-Based Geotechnical Modeling And Mapping Of An Inaccessible Underground Site, Elizabeth Anne Russell

Graduate Theses & Non-Theses

Digital photogrammetry is becoming a more common method used for mapping geological and structural rock mass features in underground mining. The issue of capturing geological and structural data in inaccessible, unsupported areas of mines remains even when utilizing terrestrial photogrammetric methods; thus, geotechnical models of mines are left with incomplete datasets. Large unsupported underground voids, like stopes, have the potential to cause major failures, but by filling in the geotechnical data gaps in inaccessible areas, potential failures can be predicted through kinematic analysis of the area’s mapped discontinuities. Implementation of Unmanned Aerial Vehicles (UAVs) in underground mines and recent advances …

Characterization Of Peak Shear Strength Of Rough Rock Joints Using The Limited Displacement Multi-Stage Direct Shear (Ldmsd) Test Method, Michael Petro

Graduate Theses & Non-Theses

Current standardized direct shear test methods for rock joints do not account for damage caused to the individually unique asperity profiles of each sample. Current test methods require either a single sample to be sheared to large displacements under successive normal stresses, or the use of similar samples in multiple tests. Successive shearing of a single sample damages surface asperities and causes the overall roughness profile of the sample to change, reducing peak shear stress and consequently resulting in underestimation of friction angle and overestimation of joint shear intercept (cohesion). Obtaining joint surface specimens with identical roughness and geometry is …

Experimental Investigation Of And Constitutive Model For The Thermo-Poro-Mechanical Deformation Of Granular Salt Under Hydrostatic Compression, Brandon C. Lampe

Civil Engineering ETDs

The influence of pore pressure and porosity on the ductile deformation of granular salt was experimentally investigated under hydrostatic compression. Confining and pore pressures were independently controlled while granular salt samples exhibited rate-dependent deformation that resulted in large decreases of sample volume and porosity. The sample deformation rates were observed to correspond with both the sample porosity and the pressure difference between the confining and pore pressures. Post-test observations revealed that the reduced porosity was caused by the solid particles deforming in a ductile manner. Insight into the cause of ductile deformation was gained by considering the local stress distribution …

Bathymetry Data For Lakes Azuei And Enriquillo, Michael Piasecki, Mahrokh Moknatian

Publications and Research

This data set supports and forms the basis for the development of Digital Bathymetry Models (DBM) for Lakes Azuei (Haiti) and Enriquillo (Dominican Republic). Bathymetric Data is typically acquired using Sonar devices that measure the depth at specific points along a boat track and for which the longitude and latitude is recorded. From the resulting point cloud one develop a seamless representation of the floor of the lake on either a raster set (which is what we have done) or try to use a contour (vector representation) model in which the depth contours appear as polygons or -lines. The raw …

Vertical Stress And Stability Of Interburden Over An Abandoned Pillar Working Before Upward Mining: A Case Study, Jinwen Bai, Guorui Feng, Shanyong Wang, Tingye Qi, Jian Yang, Jun Guo, Zhen Li, Xianjie Du, Zehua Wang, Yunlou Du, Yujiang Zhang

Faculty & Staff Scholarship

Upward mining of the residual coal seam over an abandoned pillar working is one of the effective measures to alleviate the contradiction between limited resources and increased consumption. Interburden stability over an abandoned pillar working plays a significant role in guaranteeing the safety of upward mining; however, it has not yet been extensively studied and understood. In this study, the vertical stress of the interburden over an abandoned pillar working was first investigated. The mechanical model of the interburden was established and the damage conditions were analysed. Then, the stability of the interburden over 38502 abandoned workings in Baijiazhuang coal …

The Role Of Dense Slurry In Achieving Zero Liquid Discharge, D.M. Timmons, Istvan Kovacsics

Coal Combustion and Gasification Products Journal Archive

The Coal Combustion Residual (CCR) and Effluent Limitations Guidelines (ELGs) rules pose significant technical and economic challenges for ash management and for treatment and discharge of flue gas desulfurization (FGD) wastewater at coal-fired power plants. Beneficial use is always a priority for ash, but only about half is being reused on a national basis, and the rest is destined for disposal. The U.S. Environmental Protection Agency identified biological treatment as the baseline treatment technology for FGD wastewater in the ELGs. However, it is becoming evident that bioreactors exhibit high capital and operating costs, occupy significant space, and are sensitive to …

Compressibility Of Fly Ash Under Ko Loading: Strain Rate Effects In Constant Rate Of Strain Testing, Jaime A. Mercado, Luis G. Arboleda-Monsalve, Tarunjit S. Butalia, Pedro J. Amaya

Coal Combustion and Gasification Products Journal Archive

Coal combustion processes produce large volumes of fly ash. The compressibility of fly ash was studied using moist tamping and drypluviation methods to achieve different void ratios before subjecting the material to compressive oedometric Ko loading (i.e., zero lateral deformation throughout the test). The class F fly ash used in this research was produced at a Midwest U.S. power plant. The material was initially characterized with hydrometer and specific gravity tests, and maximum and minimum realizable void ratios were determined. The compressibility characteristics of the fly ash material were studied at four strain rates, 1%/h, 10%/h, 40%/h, and 100%/h, and …

Influence Of Flow Rate On Leachability, John L. Daniels, Gautham P. Das

Coal Combustion and Gasification Products Journal Archive

The leaching potential of coal fly ash is often approximated with laboratory-based methods that expose columns of compacted material to synthetic precipitation. While this procedure can simulate aspects of the field condition, it remains difficult to replicate site-specific thermodynamic and kinetic constraints on geochemical processes. This article explores one aspect that contributes to the field/laboratory disparity, namely, the influence of flow rate and intermittency. Seven column-based leaching experiments were conducted with the same ash but with different flow rates and intermittency (i.e., infiltration pulsing), and results were evaluated in terms of aqueous sodium, calcium, and chromium concentrations in the effluent. …

Kinetic And Thermodynamic Parameters For The Adsorption Of Methylene Blue Using Fly Ash Under Batch, Column, And Heap Leaching Configurations, J.H. Potgieter, S. Pearson, C. Pardesi

Coal Combustion and Gasification Products Journal Archive

In this article, the use of fly ash, a low-cost adsorbent, for the removal of a toxic cationic dye, methylene blue (MB), from aqueous solution has been investigated. Fly ash is a waste by-product generated from coal combustion. Contrary to many other reported investigations, the fly ash was not treated prior to the experiments for this investigation. The study was done in order to ascertain the viability of using the waste material to remove cationic dyes from wastewater. While MB adsorption has been described often in batch studies, batch, column, and heap leaching studies were carried out under the same …

Universal And Excavatable Controlled Low Strength Material Using High Loss On Ignition Fly Ash And Limestone Screenings†, James T. Locum, L.K. Crouch, Daniel Badoe

Coal Combustion and Gasification Products Journal Archive

Limestone screenings and high loss on ignition (LOI) fly ash are by-products that are stockpiling because of their unintentional production and the negative effects when utilized in portland cement concretes. The research objective was to investigate whether these by-products could produce controlled low strength materials (CLSMs) meeting the three types of Tennessee Department of Transportation (TDOT) 204.06 flowable fill specifications. TDOT defines these CLSMs as the following: general use, excavatable, and early strength. Each type is required to have an inverted slump flow of not less than 15 inches (38.1 cm) while meeting ASTM International D6024 at 24 hours. Because …

A Comparative Case Study Of Reflection Seismic Imaging Method, Moones Alamooti

Electronic Theses and Dissertations

Reflection seismology is the most comand effective method to gather information on the earth interior. The quality of seismic images is highly variable depending on the complexity of the underground and on how seismic data are acquired and processed. One of the crucial steps in this process, especially in layered sequences with complicated structure, is the time and/or depth migration of seismic data. The primary purpose of the migration is to increase the spatial resolution of seismic images by repositioning the recorded seismic signal back to its original point of reflection in time/space, which enhances information about the complex structure. …

Effectiveness Of Ammonium Ion In Low Salinity Waterflooding In Shaly-Sandstone Reservoir, Hung Vu Quoc

Chulalongkorn University Theses and Dissertations (Chula ETD)

In this study was presented the pre-feasibility study of silica sand processing plant in Sihanoukville province. The resources approximately 8,750,000 tons, would be a high potential deposit for the glass industry. In this study focuses on the characteristics of the silica sand, methodology to remove the impurities which contained high Fe2O3, Al2O3 and another major oxide element, and economic evaluation technique. To identification of silica sand which used sieve analysis, Frantz isodynamic magnetic separator following by electrical microscope, XRD, and XRF. Therefore, to upgrade the quality of silica sand, which is using Shaking Table, Wet High-Intensity Magnetic Separator, and Reverse …

Limit Analysis On Seismic Stability Of Anisotropic And Nonhomogeneous Slopes With Anti-Slide Piles, Wei Bing Gong, Jing Pei Li, Lin Li

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This study employs the limit analysis method to evaluate the seismic stability of anisotropic and nonhomogeneous slopes stabilized with anti-slide piles. The pseudo-static approach is used to simplify the earthquake load. The yield seismic acceleration factor is obtained from the optimization procedure and the results are verified with the published data. Then, the seismically unstable slope is reinforced with anti-slide piles, and the seismic stability of the reinforced slope is explored. The results show that the anisotropy and Non homogeneity of soils have significant effects on the stabilizing force required from the anti-slide piles and the optimal location of the …

Failure Of The Alexander Dam Embankment And Reconstruction Using Drainage Mitigation On Kauai, Hawaii, 1930-1932, Kerry D. Cato, J. David Rogers

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Alexander Dam is a hydraulic fill earth dam and the second-highest embankment dam in Hawaii, having been built in 1929-1932 on the south side of the Hawaiian island of Kauai to provide irrigation for McBryde Sugar Company Ltd. It was constructed across Wahiawa Stream mauka (Hawaiian for "stream that comes from the mountains," literally "toward the mountains"), upstream of Kalaheo, to store 800 million gallons (5 million m3) of water to irrigate sugarcane fields. The embankment dam was intended to have a maximum height of 125 ft (38 m), a crest length of 620 ft (189 m), and a maximum …

The Utility Of Geophysical Techniques To Image The Shallow Subsurface In Karst Areas In Missouri, Nathainail Bashir

Doctoral Dissertations

"This dissertation is composed of three papers, which are focused on the utility of geophysical techniques to imaging the shallow subsurface in karst areas in Missouri.

In the first paper, ground penetrating radar (GPR) and time domain electromagnetic metal detector (TDEM-MD) methods were effectively deployed in an investigation of the cemetery with the intent of locating unmarked graves. The outcome of this study is to expand the knowledge of GPR and TDEM-MD methods, to locate unmarked graves in cemeteries. The study concluded that the GPR method is superior than TDEM-MD to locate buried caskets in cemetery investigations.

In the second …

Cenozoic Tectono-Stratigraphic Evolution And Petroleum System Of The Eastern Cordillera Foothills And Adjacent Basins (Colombia), Essam Saeid

Theses and Dissertations

New gravity, magnetic, well and 3D seismic data provides a better understanding of regional structures and tectonic movement affecting the petroleum system and sedimentary history of an important region of oil production in the Foothills of the Eastern Cordillera of Colombia. To the south the Garzón fault was previously interpreted as a right-lateral strikeslip fault. New seismic, well, and gravity data demonstrate that this fault is also a low-angle (12–17 degrees) Andean fault that thrusts PreCambrian basement 10 to 17 km northwestward over Miocene rocks of the Upper Magdalena Valley (UMV) in a prospective footwall anticline. New geophysical data as …

Ore Reserves Estimation Of The Nam Nga Coal Deposit, Lao Pdr, Using Geostatistical Method, Tongvang Bliachongvang

Chulalongkorn University Theses and Dissertations (Chula ETD)

This research study focuses on estimating the coal deposit quantity and qualities as CV and AC at Nam Nga coal deposit, Lao PDR using OK and SGS geostatistical methods. A total of 295 assays data from 51 exploration drill holes collected from LID Company were used. The results reveal that OK produces geological resource of 2.2 MT with an average CV of 3,733 kcal/kg and an average AC of 48.68 %. The mineable reserve computed from OK's ultimate pit design and pit adjustment are 0.55 MT. The OK method produces 9.32 MT of wastes, yielding a stripping ratio of 10.4:1. …