Engineering Commons^™

Electromagnetic Interference Shielding Effectiveness Of Interlayered Systems Containing Metal-Oxide, Conducting Polymer And Carbon Nanotube Reinforced Polymeric Composites, Shaik Merkatur Hakim Marjuban

Theses and Dissertations

The Electromagnetic Interference (EMI) Shielding Effectiveness (SE) has become one of the important requirements for the devices associated with telecommunication systems consisting of large frequency bands. The degradation of the quality of transmitting signal influenced by frequencies emitting from external sources can be reduced by covering the circuits of the devices by EMI Shielding materials like polymer composites, metal-based nanofiber mats, the metal of oxide films, etc. The investigation strives for the attenuation of EMI by introducing two composite mats from conducting polymer-based, multiwalled carbon nanotubes (MWCNTs) coated Nylon 6 nanofiber composites. Two other composite mats are also developed by …

Traffic Time Headway Prediction And Analysis: A Deep Learning Approach, Saumik Sakib Bin Masud

Theses and Dissertations

In the modern world of Intelligent Transportation System (ITS), time headway is a key traffic flow parameter affecting ITS operations and planning. Defined as “the time difference between any two successive vehicles when they cross a given point”, time headway is used in various traffic and transportation engineering research domains, such as capacity analysis, safety studies, car-following, and lane-changing behavior modeling, and level of service evaluation describing stochastic features of traffic flow. Advanced travel and headway information can also help road users avoid traffic congestion through dynamic route planning, for instance. Hence, it is crucial to accurately model headway distribution …

Cyber Security Evaluation Of Centos Red Hat Based Operating System Under Cyber Attack With Increasing Magnitude, William E. R. Rivas

Theses and Dissertations

The increasing interest in ‘always-connected’ devices and the Internet of Things has led to electronic devices with Internet connectivity becoming a staple in modern household and workplace. Consequently, this increase has also led to an increase in vulnerable devices, ripe for hijacking by a malicious third party. Distributed Denial of Service (DDoS) attacks have consistently been an issue since the birth of the Internet. With the large number of devices available today, the strength and consistency of these attacks has only grown and will continue to grow. Since, depending on certain variables, these DDoS attacks can effectively render a target …

Fabrication And Flow Dynamics Analysis Of Micromixer For Lab-On-A-Chip Devices, Md Fazlay Rubby

Theses and Dissertations

The miniaturized systems designed for lab-on-a-chip (LOC) technologies are generally implemented with a micro-scale mixer to provide intimate contact between the reagent molecules for interactions and chemical reactions. The exponential increase of research in microfabrication and microfluidic applications highlights the importance of understanding the theory and mechanism that governs mixing at the microscale level. In this study, the fabrication of an active and passive micromixer was discussed. The optimized state of art soft lithography and 3D printing was used as a microfabrication technique. The challenges at different fabrication steps were presented along with the modifications. Microelectrodes were integrated with the …

Growth And Characterization Of Semiconductor Materials And Devices For Extreme Environments Applications, Abbas Sabbar

Graduate Theses and Dissertations

Numerous industries require electronics to operate reliably in harsh environments, such as extreme high temperatures (HTs), low temperature (LT), radiation rich environments, multi-extreme, etc. This dissertation is focused on two harsh environments: HT and multi-extreme.

The first study is on HT optoelectronics for future high-density power module applications. In the power modules design, galvanic isolation is required to pass through the gate control signal, reject the transient noise, and break the ground loops. The optocoupler, which consists of a lighting emitting diode (LED) and photodetector (PD), is commonly used as the solution of galvanic isolation at room temperatures. There is …

Static And Dynamical Properties Of Multiferroics, Sayed Omid Sayedaghaee

Graduate Theses and Dissertations

Since the silicon industrial revolution in the 1950s, a lot of effort was dedicated to the research and development activities focused on material and solid-state sciences. As a result, several cutting-edge technologies are emerging including the applications of functional materials in the design and enhancement of novel devices such as sensors, highly capable data storage media, actuators, transducers, and several other types of electronic tools. In the last two decades, a class of functional materials known as multiferroics has captured significant attention because of providing a huge potential for new designs due to possessing multiple ferroic order parameters at the …

Security Evaluation Of Microsoft’S Windows Under Cyber-Flood Attacks, Christina Y. Navarro

Theses and Dissertations

Cyberattacks are quite common occurrences today as such can compromise entire networks producing collective vulnerabilities. As shown herein, manifold experimental findings exhibit ramifications for a cyberattack victim during multiple simulations. All experiments were conducted with Apple’s iMac, the victim system, and different editions of Microsoft Windows 10 and Windows 8.1.

Cyberattacks herein categorize as Distributed Denial of Service (DDoS) attacks including Smurf, Ping Flood, Transmission Control Protocol-Synchronize (TCP-SYN) Flood, and User Datagram Protocol (UDP) Flood attacks. Experimental results from each cyberattack are recordings of computer activities such as memory consumption, disk utilization, and overall processor utilization.

DDoS attack simulations include …

The Effect Of Intensive Auditory Cues On Flight Passengers’ Safe Behaviors, Tianhua Li

Theses and Dissertations

When passengers do not follow in-flight announcements, injuries can occur. It is critical to draw passengers’ attention and help them be aware of the importance of the instructions provided during in-flight announcements. Passengers’ attention can be improved by providing intensive auditory cues before announcements. The auditory cues with intensive acoustic parameters increase the hearers’ perceived level of urgency, and then, they are more likely to perform safer behaviors. Also, when the intensity level increases to an intermediate level, the stimulated persons should have better performance. However, when it increases excessively, their performance may be impaired. The study examined the effect …

Identifying The Need For Trained Machinists In The Greater Tri-Cities Area, Bradley Stufflestreet

Electronic Theses and Dissertations

Machinists are skilled tradespeople responsible for running a variety of machine tools to produce precision components for end-users or use in other manufacturing. This project identifies the current and future change in the number of machinists in the Tri-Cities area, especially the five-county service area of Northeast State Community College. Using an industry survey, the need for machinists is identified and evaluated to understand local employers’ needs. The results indicate industry needs more machinist to keep up with demand, as 6 out of 14 companies have open positions and, 8 reported difficulty filling openings. Furthermore, most companies are growing or …

A Comparison Of Methods To Measure Crop Water Use In South Carolina, Andrew C. Ewing

All Theses

The objective of this thesis was to compare cost-effective methods of measuring crop water use, known as evapotranspiration (ET), in South Carolina’s humid climate. The methods analyzed were the surface renewal method (SR), the Eddy Covariance method (EC), large in-field weighing lysimeters, a newly developed pressure differential device (PDD), a Class A Evaporation pan, and the Penman-Monteith equation. In the first chapter, ET measurements obtained by SR were compared to ET measured by EC and weighing lysimeters. For reference, EC and SR track the energy budget to estimate ET, while the weighing lysimeters used in this study are box-like containers …

Ultrafast Spin-Currents And Charge Conversion At 3d-5d Interfaces Probed By Time-Domain Terahertz Spectroscopy, T. H. Dang, J. Hawecker, E. Rongione, G. Baez Flores, D. Q. To, J. C. Rojas-Sanchez, H. Nong, J. Mangeney, J. Tignon, F. Godel, S. Collin, P. Seneor, M. Bibes, A. Fert, M. Anane, J. M. George, L. Vila, M. Cosset-Cheneau, D. Dolfi, R. Lebrun, P. Bortolotti, Kirill Belashchenko, S. Dhillon, H. Jaffrès

Kirill Belashchenko Publications

Spintronic structures are extensively investigated for their spin-orbit torque properties, required for magnetic commutation functionalities. Current progress in these materials is dependent on the interface engineering for the optimization of spin transmission. Here, we advance the analysis of ultrafast spin-charge conversion phenomena at ferromagnetic-Transition metal interfaces due to their inverse spin-Hall effect properties. In particular, the intrinsic inverse spin-Hall effect of Pt-based systems and extrinsic inverse spin-Hall effect of Au:W and Au:Ta in NiFe/Au:(W,Ta) bilayers are investigated. The spin-charge conversion is probed by complementary techniques-ultrafast THz time-domain spectroscopy in the dynamic regime for THz pulse emission and ferromagnetic resonance spin-pumping …

Software Development With Scrum: A Bibliometric Analysis And Profile, Peter Kokol, Sašo Zagoranski, Marko Kokol

Library Philosophy and Practice (e-journal)

Introduction of the Scrum approach into software engineering has changed the way software is being developed. The Scrum approach emphasizes the active end-user involvement, embracing of change, and /iterative delivery of products. Our study showed that Scrum has different variants or is used in combination with different methods. Some tools not normally used in the conventional software approaches, like gamification, content analysis and grounded theory are also employed. However, Scrum like other software development approach focuses on improvement of software process, software quality, business value, performance, usability and efficiency and at the same time to reduce cost, risk and uncertainty. …

Novel Memristor Based True Random Number Generator, Scott Stoller

Boise State University Theses and Dissertations

Random numbers are an important, but often overlooked part of the modern computing environment. They are used everywhere around us for a variety of purposes, from simple decision making in video games such as a coin toss, to securing financial transactions and encrypting confidential communications. They are even useful for gambling and the lottery.

Random numbers are generated in many ways. Pseudo random number generators (PRNGs) generate numbers based on a formula. True random number generators (TRNGs) capture entropy from the environment to generate randomness. As our society and our devices become more connected in the digital world, it is …

2020 Summer-Fall Graduate Recognition Program, Propulsion Research Center, Robert Frederick

PRC Graduate Recognition

This program includes the graduate recognition program for summer and fall 2020. Includes photographs, upcoming events, recent publications, and student profiles.

Effects Of Ca Doping On Structural And Optical Properties Of Pzt Nanopowders, K. H. Omran, M. Mostafa, M. S. Abd El-Sadek, O. M. Hemeda, R. Ubic

Materials Science and Engineering Faculty Publications and Presentations

The influence of the addition of calcium ions (Ca²⁺) in the Pb_(1-x)Ca_xZr_0.52Ti_0.48O₃ system (PCZT) for x = 0.05, 0.10, 0.15, 0.20, and 0.25 on the structural and optical properties was systematically studied. The compositions were synthesized through a polymerized-complex approach based on the Pechini polymeric precursor route. The solubility limit of calcium ions within the PCZT lattice is in between x = 0.10 and x = 0.15, at which a CaTiO₃ secondary phase is detected. The Goldschmidt tolerance factors, modified tolerance factors, and the effective vacancy sizes were …

Dynamic Friction Measurements Of Egyptian Cotton Yarns Part 1: Study Of Frictional Behavior Of Two Component Blended Staple Yarns., R. El-Bealy, M. Salama, S. Ibrahim

Mansoura Engineering Journal

In the present work, the dynamic frictional characteristics of Egyptian cotton, Misr polyester and cotton/polyester blended staple yarns were studied. The frictional coefficient of yarns have been determined by wrapping around a cylindrical pin. The electronic F-Meter R 1182 of firm Rotschild zurich was used. The frictional coefficient blended yarns was found to be influenced by fiber constituents, blend proportion, yarn linear density, threadline speed, pretension and angle of contact (loop size).

Vibration Analysis Of Simultaneous Drilling And Reaming Bha, Mohammed F. Al Dushaishi, Daniel S. Stutts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The drillstring used in the oil and gas exploration is a complex structure due to the different forces acting on it. One of the primary sources of drillstring vibrations is the cutting forces caused by the drill bit contact with the rock formation. In some drilling applications, such as hole enlargement and underreaming, the source of the cutting action originates from the drill bit as well as the reamer which increases the dynamic complexity of the drillstring. This paper’s objective is to investigate the torsional vibration behaviors of the bottom hole assembly (BHA) under simultaneous drilling and reaming. More specifically, …

Coalescence Speed Of Two Equal-Sized Nanobubbles, Eric Bird, Jun Zhou, Zhi Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In This Work, We Use Molecular Dynamics (MD) Simulations Coupled with Continuum-Based Theoretical Analysis to Study the Coalescence Dynamics of Two Equal-Sized Nanobubbles (NBs). We First Derive a Governing Equation for the Evolution of the Capillary Bridge Radius between Two Coalescing NBs from the Axisymmetric Navier-Stokes Equation. to Verify the Prediction from the Governing Equation, We Carry Out MD Simulations of the Coalescence of Two NBs in a Lennard-Jones Fluid System and Directly Measure the Bridge Radius, Rb, as a Function of Time, T. by Varying the Bubble Diameter, We Change the NB Ohnesorge Number from 0.46 to 0.33. in …

Characterization Of A Packaged Triboelectric Harvester Under Simulated Gait Loading For Total Knee Replacement, Nabid Aunjum Hossain, Geofrey George Yamomo, Ryan Willing, Shahrzad Towfighian

Mechanical Engineering Faculty Scholarship

Load sensing total knee replacement (TKR) implants are useful tools for monitoring prosthesis health and providing quantitative data to support patient claims of pain or instability. Powering such devices throughout the entire life of the knee replacement, however, is a challenge, and selfpowered telemetry via energy harvesting is an attractive solution. Herein, we implemented vertical contact mode triboelectric energy harvesters inside a knee implant package to generate the power required for embedded digitization and communications circuitry. The harvesters produce small-scale electric power from physiologically relevant loads transmitted through the knee. Experiments were performed on a joint motion simulator with an …

High Performance Thermal Straps For A Full Range Of Application Temperatures, M. Ralphs, M. Sinfield, M. Felt

Space Dynamics Laboratory Publications

Thermal straps are an essential component when using vibration sensitive instruments and cryocoolers in close proximity. Thermal straps conduct heat from the instrument to the cryocooler while limiting the amount of mechanical vibration the cryocooler transfers back to the instrument. Thermal straps are made from flexible, thermally conductive materials. Traditionally, they are made of metal – aluminum or copper, mostly – that has been formed into thin foils, wires, or braids to provide greater flexibility while still providing good thermal conductivity. These metallic straps, if made from pure metals, provide superior thermal performance at cryogenic temperatures ( < 60 K ) where their thermal conductivities peak to extraordinary levels. Pyrolytic graphite sheet (PG S) thermal straps have a thermal conductance that peaks at higher temperatures – approximately 160 K – and provide much higher mass-specific thermal conductance at temperatures above 60 K than metallic straps. This paper discusses the pros and cons of aluminum, copper, and PG S thermal straps along with different techniques to test their thermal and mechanical performance.

The Effects Of Aircraft Use And Available Repar Spares On Aircraft Sortie Generaiton: A Long-Duration Logistical Wargaming Simulationtool, Nathaniel M. Choo

Theses and Dissertations

A long-duration logistical wargame simulation tool that can provide quick insights into the daily aircraft availability and the daily number of missions accomplished for a variety of operational scenarios is developed. This simulation tool is designed to be a stepwise wargaming support tool for adjudication within long-duration logistical wargames and provides the user many capabilities including, but not limited to, the ability to have multiple bases and types of aircraft. Additionally, the user has the ability to control types of part failures, control parts availability, control maintenance capabilities, and control number of mission scheduled. Finally, the user can account for …

A Low-Cost Secure Iot Mechanism For Monitoring And Controlling Polygeneration Microgrids, Josué Martínez-Martínez, Diego Aponte-Roa, Idalides Vergara-Laurens, Wayne Weaver

Michigan Tech Publications, Part 1

The use of Internet-connected devices at homes has increased to monitor energy consumption. Furthermore, renewable energy sources have also increased, reducing electricity bills. However, the high cost of the equipment limits the use of these technologies. This paper presents a low-cost secured-distributed Internet of Things (IoT) system to monitor and control devices connected in a polygeneration microgrid, as a combined power system for local loads with renewable sources. The proposed mechanism includes a Wireless Sensor Actuator Networked Control System that links network nodes using the IEEE 802.15.4 standard. The Internet communication enables the monitor and control of devices using a …

Designing An Autonomous Goods-To-Person Order Picking System: From Storage To Pick., Mina Shekari Ashgzari

Electronic Theses and Dissertations

In recent years, there has been an increased growth in e-commerce, which is a special case of a business-to-customer model. Among all the operations for fulfilling online orders, order picking has been the concern of many researchers and practitioners in the field of warehousing and material handling. This is due to very different technical assumptions and service expectations for online retailers compared to the case of business-to-business models. The most fundamental change in order processing, imposed by business-to-customer models, is shipping individual items or “eaches,” instead of cases and pallets, which is typical of business-to-business models. As a result, the …

Heat Transfer Modeling And Optimization Of A Carbonized Microvascular Solar Receiver, Taylor Brown

Boise State University Theses and Dissertations

Concentrating solar power is an emerging renewable energy source. The technology can collect and store thermal energy from the sun over long durations, generating electricity as needed at a later time. Current CSP systems are limited to a maximum operational temperature due to constraints of the working fluid, which limits the maximum possible efficiency of the system. One proposed pathway forward is to utilize a gas phase for the working fluid in the system such as supercritical carbon dioxide.

A composite gas phase modular receiver is being developed by researchers at Boise State University and the University of Tulsa. The …

In-Situ Fluid Injections To Achieve Bio-Stimulated Calcite Precipitation In Expansive Soils, Anish Pathak

Boise State University Theses and Dissertations

Expansive soils undergo vast changes in volume when subject to change in water contents and cause damages to infrastructures across the world. Traditional methods of tackling the problem of expansive soils using cement or lime are environmentally unfriendly and expensive. Microbial Induced Calcite Precipitation (MICP) is a new method which uses bacteria in the soil to precipitate CaCO3 (calcite) and improve the engineering properties of soils. Various laboratory studies have shown that this method can be applied successfully to treat expansive soils, but the field application of the method have barely been studied.

To study the applicability of MICP in …

A Resilience Metric For Modern Power Distribution Systems, Tyler Bennett Phillips

Boise State University Theses and Dissertations

Modern society has become increasingly reliant on the functioning of critical infrastructure. It is considered so vital that its incapacitation or destruction would have debilitating effects on the global economy, national security, and public health and safety. The electrical power system is uniquely positioned, as it is essential for all other sectors of critical infrastructure to operate as intended. However, it is constantly at risk due to factors such as natural disasters, climate change, aging infrastructure, and cyber threats. Thus, ensuring the efficient and continuous supply of electricity is of utmost importance and the topic of this dissertation.

The work …

Smart Solar Charge Controller, Aria Pegah, Miclaine Emtman

Electrical Engineering

The technology of photovoltaics has been quickly evolving as we move toward a future with more clean energy. Energy conversion efficiency is key to making these systems the viable option amongst other sources of power. This project proposes a way to increase the power yield from a solar system by implementing smarter algorithms in the maximum power point tracking (MPPT) component of the system. MPPT is critical because environmental conditions may vary significantly for any given system due to irradiance and shading. The proposed method for MPPT utilizes a controller that uses swarm intelligence to do the power tracking.. This …

Design, Discovery, And Characterization Of Single Crystals Of A Topological Semimetal Using A Self-Flux Method, Sudha Krishnan

Graduate Theses/Dissertations

Realization of topological semimetals in the recent past show that ternary intermetallics can exhibit topological phases. This discovery initiated the quest for this novel research. There is a crucial need to discover new materials that manifest these phases for a better understanding of their behavior to utilize them in device technology. Also, Bi compounds have attracted much attention as candidates for topological materials and topological superconductors. In this context, synthesis and characterization of single crystals of a layered transition metal pnictide SmMnBi2, a potential Dirac topological semimetal candidate, is reported. A flux method was utilized to synthesize single crystals of …

Exploring The Variability In The Gray Scale Imaging Process Of Asphalt Samples, David Oluwawade Olatunji

Civil Engineering Undergraduate Honors Theses

Gray scale image analysis is a powerful tool for testing asphalt concrete materials. From material composition to surface properties, gray scale analysis has shown evidence as a non-invasive way to obtain information from asphalt samples. Casillas et al. used a gray scale analysis to measure the Representative Volume Element of three asphalt sample geometries to understand the minimum size at which an asphalt sample is representative of a larger homogeneous mixture [1]. While the gray scale analysis used in this experiment yielded results, there were unknown factors in the image capturing process. Particularly, not much was known about the effect …

Measuring Pilot Control Force In General Aviation: Strain Gauges And Load Cell, Benjamin David Wyma

Theses and Dissertations

Flight test requires a variety of sensors and data systems to accurately read variables on an aircraft during testing. One of these important variables is the pilots control force. Control force is used in many tests in flight test to ensure the aircraft being tested meets the required FAA standards. One essential test is stick free longitudinal stability where control force is needed to calculate the stick free neutral points of the aircraft [1]. The objective of the project was to explore two methods of electronically measuring control force and determining which method is best suited for Florida Institute of …