Engineering Commons^™

Quantification Of Optical Parameters Using Frequency Domain Functional Near-Infrared Spectroscopy (Fd-Fnirs), Christopher W. Davies

Browse all Theses and Dissertations

Near infrared spectroscopy (NIRS) is a non-invasive technique that uses near-infrared light and hemoglobin as the contrast to characterize tissue optical properties, namely optical absorption [����] and scattering [����′ ]. Through this characterization, it is possible to obtain information about the tissue’s oxygenated (HbO) and deoxygenated (Hb) hemoglobin concentrations and oxygen saturation which are important physiological markers for diagnosis and intervention monitoring. Many commercial devices use a continuous wave approach (CW-fNIRS), a technique that simply relies on intensity changes from a constant power laser to determine only relative changes in oxygenation. This is a significant limitation for clinical settings where …

Rescue Of Als Protein Fus Toxicity By Taf, Elliott Hayden

Browse all Theses and Dissertations

Amyotrophic Lateral Scleroses (ALS) is a neurodegenerative disease characterized by the degeneration of upper and lower motor neurons in the brain and spinal cord leading to progressive paralysis and ultimately death within 5 years of symptom onset. Only two drugs are approved by the Food and Drug Administration (FDA) for treating ALS that slow the disease progression by about 3 months. Mutations in the gene Fused in Sarcoma (FUS) cause inherited forms of ALS. FUS is a nuclear, multifunctional RNA-binding protein (RBP) involved in multiple RNA metabolic pathways. Mutations in FUS cause mislocalization of the protein from the nucleus to …

Improve Operating Room Utilization Through Distributed Scheduling Workflow And Automation, Miteshkumar Mahendrabhai Vasoya

Browse all Theses and Dissertations

Operating room (OR) plays a crucial role in health care, contributing more than 50% of the hospital’s revenue and incurring over 35% of the hospital’s expense, ultimately determining the hospital’s profitability. Moreover, because the OR is a primary source of admissions, it is virtually impossible to streamline hospital‐wide workflow without first streamlining patient flow through the OR. Unfortunately, current OR scheduling practices often limit the utilization of OR, one of the most expensive resources in the health care industry, to around 60%. On the other hand, many patients have to wait an excessively long time before their surgeries can be …

The Characterization And Fatigue Life Impact From Surface Roughness On Structurally Relevant Features Produced Using Additive Manufacturing, Eric-Paul Daniel Tatman

Browse all Theses and Dissertations

Additive manufacturing (AM) produces rough surfaces that are detrimental to the mechanical performance of the part. In this work, downward-facing surfaces were fabricated in alloy 718 using laser powder bed fusion and investigated with surface characterization and axial fatigue testing. Coupons with downward-facing surfaces at 45°, 60°, and 75° and flat axial fatigue bars with as-built and machined holes were built. Both specimens were fabricated with three levels of downskin laser power and the coupons with three levels of downskin laser speed. Surface characterization showed roughness increased as the downward-facing angle decreased. Fatigue testing with digital image correlation showed localized …

A Transfer Matrix Model Of The Iec 60318-4 Ear Simulator: Application To The Simulation Of Earplug Insertion Loss, Yu Luan, Franck Sgard, Simon Benacchio, Hugues Nélisse, Olivier Doutres

Études primaires

The IEC 60318-4 ear simulator is used to measure the insertion loss (IL) of earplugs in the ear canal of an acoustical test fixture (ATF) and is designed to represent an average acoustic impedance (in a reference plane) of the human ear. The ear simulator is usually modeled using a lumped parameter model (LPM) which has frequency limitations and inadequately accounts for the thermo-viscous effects in the simulator. The simulator numerical models that can better deal with the thermo-viscous phenomena often lack essential geometric details. Most related studies also suffer from the lack of experimental validation of the models. Therefore, …

Use Of Magnetic Resonance Image Registration To Estimate Displacement In The Human Earcanal Due To The Insertion Of In-Ear Devices, Simon Benacchio, Olivier Doutres, Arthur Varoquaux, Éric Wagnac, Arnaud Le Troter, Virginie Callot, Franck Sgard

Études primaires

In-ear devices are used in a wide range of applications for which the device's usability and/or efficiency is strongly related to comfort aspects that are influenced by the mechanical interaction between the device and the walls of the earcanal. Although the displacement of the earcanal walls due to the insertion of the device is an important characteristic of this interaction, existing studies on this subject are very limited. This paper proposes a method to estimate this displacement in vivo using a registration technique on magnetic resonance images. The amplitude, the location and the direction of the earcanal wall displacement are …

Long-Term Impact On Environmental Attitudes And Knowledge Assessed Over Three Semesters Of An Environmental Engineering Sequence, Benjamin Michael Wallen, Nathaniel Sheehan, Luke Plante, Erick Martinez, Jeffrey A. Starke

Civil and Environmental Engineering Faculty Research and Publications

The pedagogy employed in a three-course environmental engineering sequence is investigated to determine the efficacy of enabling long-term improvement of knowledge and attitudes toward the environment. These three courses incorporate concepts of the five grand challenges released by the National Academy of Engineering and National Academy of Sciences and increase the breadth of knowledge for T-professionals. Previous studies of lengths from a few weeks to semester long courses evaluated the potential causality among various demographics and environmental knowledge and attitudes. The research presented herein contrasts and compares changes in environmental knowledge based upon a 12-question survey and changes in environmental …

Engaging Undergraduate Students In The Philippines In Photonics Research With A Novel Publication-Driven Online Mentoring Approach, Minella C. Alarcon, Benjamin Dingel, Annelle Chua, Aria Buenaventura, Nathaniel Joseph C. Libatique

Electronics, Computer, and Communications Engineering Faculty Publications

This paper discusses a publication-driven, education-by-research model of engaging undergraduate students in Photonics/Optics/Physics research by requiring that all activities lead to journal publication within a year. It is based on a non-traditional university-industry collaboration arrangement that has the following unique features.

First, it utilizes offshore-based alumni (in the USA) who are active in science and technology research as mentors for the students (in the Philippines) in conjunction with the university professor advisers. We adopt inexpensive online collaboration technologies to support their virtual presence.

Second, our research topic “fuses” uniquely two separate courses of study, namely: (i) the traditional Special Relativity …

Enhancing Group Social Perceptiveness Through A Swarm-Based Decision-Making Platform, David A. Askay, Lynn E. Metcalf, Louis Rosenberg, Gregg Willcox

Industrial Technology and Packaging

Swarm Intelligence is natural phenomenon that enables social animals to make group decisions in real-time systems. This process has been deeply studied in fish schools, bird flocks, and bee swarms, where collective intelligence has been observed to emerge. The present paper describes swarm.ai—a collaborative technology that enables swarms of humans to collectively converge upon a decision as a real-time system. Then we present the results of a study investigating if groups working as “human swarms” can amplify their social perceptiveness, a key predictor of collective intelligence. Results showed that groups reduced their social perceptiveness errors by more than half when …

Measuring Group Personality With Swarm Ai, Gregg Willcox, David Askay, Louis Rosenberg, Lynn Metcalf, Bryan Kwong, Richard Liu

Industrial Technology and Packaging

The aggregation of individual personality tests to predict team performance is widely accepted in management theory but has significant limitations: the isolated nature of individual personality surveys fails to capture much of the team dynamics that drive real-world team performance. Artificial Swarm Intelligence (ASI), a technology that enables networked teams to think together in real-time and answer questions as a unified system, promises a solution to these limitations by enabling teams to take personality tests together and converge upon answers that best represent the group’s disposition. In the present study, the group personality of 94 small teams was assessed by …

Magnetic Field Sensor Based On A Tri-Microfiber Coupler Ring In Magnetic Fluid And A Fiber Bragg Grating, Fangfang Wei, Dejun Liu, Arun Kumar Mallik, Gerald Farrell, Qiang Wu, Gang-Ding Peng, Yuliya Semenova

Articles

In this paper we propose and investigate a novel magnetic field sensor based on a Tri-microfiber coupler combined with magnetic fluid and a fiber Bragg grating (FBG) in a ring. A sensitivity of 1306 pm/mT was experimentally demonstrated in the range of magnetic fields from 0 to 15 mT. The reflection peak in the output spectrum associated with the FBG serves as a reference point allowing to avoid ambiguity in determining the spectral shift induced by the magnetic field. Due to its high sensitivity at low magnetic fields, the proposed structure could be of high interest in low field biosensing …

Analysis Of Crush Resistance And Mississippi-Sourced Sands To Determine Potential As Proppant Sands, Ryann C. Lam

Honors Theses

Proppant is a media used in hydraulic fracturing to bear in-situ stresses in order to maintain fracture networks, which act as highly permeable pathways for hydrocarbon recovery. Proppant can be made from a variety of materials such as glass, ceramic beads, sand particles, and more. Proppants are characterized by their size, sorting, roundness, and sphericity. These properties help determine the compressive strength of the pack proppant. This study focuses on these properties for natural sand. The purpose of this study is to evaluate the viability of lower-quality sands as proppant sands by testing the affect these properties have on the …

Optimization And Cost Comparison Of Reactor Types In A Styrene Production Process, Claire Lenore Cozadd

Honors Theses

The focus of this thesis is to use the equivalent annual operating costs of isothermal, adiabatic, and packed bed reactors in order to determine which reactor is most cost effective in a styrene production process. In order to understand the steps leading up to this comparison, background information is first given regarding chemical engineering design, optimization, and process simulation. This information was necessary for completing the ChE 451 design project, which was to analyze the base case styrene process before optimizing it, in fall 2018. The results of this project are briefly outlined in the second section. The third section …

Discrete Optimization Of A Styrene Production Process, Seth Gray

Honors Theses

This thesis will outline the two phases of my capstone design project for Chemical Engineering. The first goal was to simulate a styrene production process in Excel alongside my group members in ChE 451. During this phase, we looked at startup of the process and the first 12 years of operation. After the base case which included an isothermal reactor, the decision was made to switch to an adiabatic reactor based on net present value evaluations. Discrete optimization took place on the adiabatic reactor and the subsequent process. The second phase of my capstone project was the portion assigned to …

Determination Of Shrinkage Of Fine-Grained Soils Using 3d Scanning Technology, Hemant R. Joshi

Honors Theses

Shrinkage Limit is the moisture content parameter in fine grained soil which is related to the volume stability of the soil. The conventional method, ASTM Standard D427-04 that uses mercury has been replaced by wax method, ASTM Standard D4943-02 that uses wax and water or MT-92 that uses spray coating. This modification has certainly minimized safety concerns of the laboratory technicians by avoiding the use of the health hazardous substance, mercury (Hg) but it is not really an economic and convenient method. This thesis proposes a 3D scanning method of determining the shrinkage limit of fine grained soils. The 3D …

Safety Considerations For The Design Of Modern Elevator Systems, Abhijaya Shrestha

Honors Theses

The main purpose of this work is to perform an analysis on elevator safety considerations in the United States. This report introduces the development of elevators through its history, definitions and commonly used concepts in the elevator industry. Elevators are already an important part of day-to-day life for thousands of people and have significant role to play in the future of urbanization due to increasing population density and decreasing real estate. Elevators not only make vertical transportation convenient, but also play an important role in providing accessibility for people with disabilities; so, its safe and reliable operation is very crucial. …

Attitudes Toward Failure In Capstone Design Projects, Jay R. Goldberg

Biomedical Engineering Faculty Research and Publications

While working in industry during the 1980s and 1990s, project failures were to be avoided at all costs. For engineers in the medical device industry, these failures could be in the form of: 1) an idea for a new product or feature that eventually failed due to technical infeasibility, regulatory hurdles, lack of market interest, or difficulty in manufacturing; 2) a prototype that did not function as required; or 3) an animal or human clinical study that yielded poor results. They typically resulted in significant project delays, wasted time and money, and lost revenues, and often led to lower raises, …

Bridge Safety Against Multi-Hazard, Yahya Mohammed Mohammed

All ETDs from UAB

Multiple hazards (e.g., earthquake, wind gust, flood, vessel collision, traffic overload and accidents, and terrorist attacks, etc.) must be properly considered in highway bridge design in addition to the normal functionality requirements. Unfortunately, the structural health of bridges are continuously deteriorated over time, this in tandem with an excessive increase in hazard events, which makes the network extremely vulnerable to natural hazards. The main goal of this dissertation is to provide methods to investigate bridges safety against multi-hazard by obtaining load scenarios and evaluation of the performance based on these loads. Hazard events have been divided into routine events and …

Renewables-Integrated Internal Combustion Engine-Based Multi-Generation Options For Uab Buildings, Qing Mu

All ETDs from UAB

Distributed energy, also district or decentralized energy is generated or stored by a variety of small, grid-connected devices referred to as distributed energy resources, or distributed energy resource systems. The Distributed Generation (DG) systems can increase energy system reliability, reduce peak power requirements, and improve energy infrastructure resilience. In this study, a DG system using renewable energy sources and energy storage has been introduced for the whole University of Alabama at Birmingham (UAB) campus. The energy sources for this DG system are photovoltaic arrays, a natural-gas-powered Internal Combustion Engine (ICE), and wind turbines. The energy storage component used in this …

The Role Of The Built Environment In Transforming Underserved Neighborhoods Into Smart And Connected Communities, Mary Claire Nabors

All ETDs from UAB

The goal of this report is to create a model for transforming underserved neighborhoods into smart, connected, healthy, and sustainable communities by focusing on the built environment. To do this, there must be a thorough neighborhood analysis of the existing conditions with recommendations for what needs to be done, both short term and long term. The built environment impacts many aspects of a neighborhood and the quality of life for residents. Sidewalks, streets, lighting, landscaping, and accessibility are all components of the built environment and research has continuously shown how the deterioration of the built environment affects the health and …

Bending Response Of Timber Mortise And Tenon Joints Reinforced With Filler-Modules And Frp Gussets, Andrew Robert Pacifico

Graduate Theses, Dissertations, and Problem Reports (ETD)

In 2013, the California Bay Area (CBA) passed a set of ordinances to ensure that their 10,000 plus timber soft-story buildings were prepared for seismic events, through nondestructive evaluation methods. Many property owners are searching for an affordable retrofitting system that will also meet CBA’s new laws focusing on installations by the mandated deadlines in 2020. Over the past three to four decades, Fiber Reinforced Polymer (FRP) composites have found their way into the civil infrastructure sector for rehabilitation. The objective of this study is to evaluate the bending behavior retrofitted mortise and tenon timber joints reinforced with engineered wood …

Computational Design Of Staged Pressurized Oxy-Coal Combustion, Gideon Ozioma Udochukwu

Graduate Theses, Dissertations, and Problem Reports (ETD)

Staged pressurized oxy-coal combustion (SPOC) is nowadays a promising technology to be used for low-cost, low-emission, high-efficiency power generation. The objective of this thesis is to compliment the experiments ongoing at the Washington University, St. Louis (WUSTL) by means of numerical simulations, thereby providing better understanding of the fluid flow, turbulence, combustion characteristics, particle dynamics and heat transfer. Carbon dioxide (CO2) is injected alongside the coal, for its carriage. A small amount of methane (CH4) is also injected alongside the coal to maintain a steady flame. The simulations are performed for a 3D geometry with the following energy source distribution: …

Security Bug Report Classification Using Feature Selection, Clustering, And Deep Learning, Tanner D. Gantzer

Graduate Theses, Dissertations, and Problem Reports (ETD)

As the numbers of software vulnerabilities and cybersecurity threats increase, it is becoming more difficult and time consuming to classify bug reports manually. This thesis is focused on exploring techniques that have potential to improve the performance of automated classification of software bug reports as security or non-security related. Using supervised learning, feature selection was used to engineer new feature vectors to be used in machine learning. Feature selection changes the vocabulary used by selecting words with the greatest impact on classification. Feature selection was able to increase the F-Score across the datasets by increasing the precision. We also explored …

Development Of A Dynamic Model And Control System For Load-Following Operation Of Supercritical Pulverized Coal Power Plants, Parikshit S. Sarda

Graduate Theses, Dissertations, and Problem Reports (ETD)

Thermal power plants that have been designed to operate at their rated capacity are being forced to cycle their load and operate under low-load condition to meet changing load demands due to the increased penetration of renewables into the electric grid. The rapid load-following operation is leading to challenging control problems. The goal of this research is to develop dynamic model and control system for efficient load-following operation. The focus of this work is on supercritical pulverized coal (SCPC) power plants. The steady-state model is developed using Aspen Plus and Aspen Custom Modeler and then converted to a pressure-driven Aspen …

Evaluation Of Ultra Fine Cigarette Smoke Particles Penetration On 3m 6200 Half Mask Respirators With P-100 Filters, Selcuk Elhan

Graduate Theses, Dissertations, and Problem Reports (ETD)

This study was aimed to investigate the effectiveness of half mask respirator with double P-100 filters by determining the penetration of cigarette smoke particles. In this study, faceseal leakage of a breathing manikin donned a 3M 6200 half mask elastomeric respirator with double P-100 filters was determined at various test conditions. A full factorial test conditions of 4 sealing conditions (Non-sealed, only nose sealed, nose and chin sealed, and fully sealed), 2 inspiratory breathing types (Constant, cyclic), 4 flowing rates (15, 30, 50, 85 L/min for cyclic; 15, 30, 50, 80 L/min for constant) were employed and each test condition …

In Situ Measurement Of Fatigue Induced Crack Growth In Inconel 718 Using Direct Current Potential Drop Method, Joel C. Lindsay

Graduate Theses, Dissertations, and Problem Reports (ETD)

With recent advances in air breathable engines comes more extreme temperature environments that engine components must tolerate. During the design of these engines, it is necessary to understand how material fatigue failures occur at these new, higher operating temperatures. In providing understanding, the following fundamental study focuses on the statistical nature of crack jumps (changes in crack length over time) during fatigue in a polycrystalline nickel-based superalloy, Inconel 718 (IN718). In situ measurement of the crack length at several loading conditions were conducted using a direct current potential drop (DCPD) measurement method. Experimental data was collected at six different fatigue …

Towards A Framework For Smart Manufacturing Adoption In Small And Medium-Sized Enterprises, Sameer Mittal

Graduate Theses, Dissertations, and Problem Reports (ETD)

Smart Manufacturing (SM) paradigm adoption can scale production with demand without compromising on the time for order fulfillment. A smart manufacturing system (SMS) is vertically and horizontally connected, and thus it can minimize the chances of miscommunication. Employees in an SME are aware of the operational requirements and their responsibilities. The machine schedules are prepared based on the tasks a machine must perform. Predictive maintenance reduces the downtime of machines. Design software optimizes the product design. Production feasibility is checked with the help of simulation. The concepts of product life cycle management are considered for waste reduction. Employee safety, and …

Time-Dependent Deformation And Associated Failure Of Roof In Underground Mines, Yuting Xue

Graduate Theses, Dissertations, and Problem Reports (ETD)

In underground coal mines, roof falls are a major contributor to injuries and fatalities. Studies have related the occurrence of roof fall to weak immediate roof, high horizontal stress, entry orientation, etc. An often-neglected factor in studies on this topic has been the influence of time-dependent behavior of the roof rock on roof falls. The time-dependent roof failure activity involves both intact and failed rocks. Numerical simulation techniques are available that include time-dependent behavior; however, they lack constitutive models that consider both the intact and the failed behavior of rock. In addition, input properties for the creep models only include …

Optimal Compression Of Point Clouds, Benjamin Robert Smith

Graduate Theses, Dissertations, and Problem Reports (ETD)

Image-based localization is a crucial step in many 3D computer vision applications, e.g., self-driving cars, robotics, and augmented reality among others. Unfortunately, many image-based-localization applications require the storage of large scenes, and many camera pose estimators struggle to scale when the scene representation is large. To alleviate the aforementioned problems, many applications compress a scene representation by reducing the number of 3D points of a point cloud. The state-of-the-art compresses a scene representation by using a K-cover-based algorithm. While the state-of-the-art selects a subset of 3D points that maximizes the probability of accurately estimating the camera pose of a new …

Modeling And Development Of The Dynamic Environmental Simulation Chamber (Desc) For Calibration Of Air Quality Monitoring Sensors, Filiz Kazan

Graduate Theses, Dissertations, and Problem Reports (ETD)

The thesis describes the development steps for the dynamic environmental simulation chamber (DESC) and carbon dioxide sensor calibration by using DESC. The sensors are Figaro, COZIR and K30 CO2 sensors