Engineering Commons^™

Making Alloys (Ti1 - Xalx) N Using Plasma Cvd Technique From Alcl3 Powder, H2 And N2 Gas ,With Solvent Ticl4, Keba Moto

Makara Journal of Technology

The substitution of Ti atoms by Al atoms in TiN lattice sites to form (Ti1-xAlx)N is clearly demonstrated by the coatings which were deposited on steel substrate and using plasma CVD technique. The presence of Al atoms in TiN lattice site is shown by means of XRD and EDX techniques: lattice parameters decreasing of TiN as the fraction of Al increases (XRD) and precipitation of hexagonal AlN phase (XRD) as the fraction of Al exceeding 0.8 (EDX). The hardness of these coating are just around 30 GPa, which is beyond the values reported in literatures.

Effects Of 0.25 % Mo (Molybdenum) Which Is Contained In The Ductile Cast Iron On Mechanical Properties Of Austempered Ductile Iron (Adi)., Nukman Nukman, Bustanul Arifin, Bambang Sugiarto

Makara Journal of Technology

The aim of this research is to investigate the effects of 0.25 % Mo (Molybdenum) which is contained in the ductile cast iron on mechanical properties of Austempered Ductile Iron (ADI). The various temperatures and the holding times are used in the heat treatment processes. Using a given 0.25 % Mo in the ductile iron, ADI's alloyed developes a higher ultimate tensile stress value and decreases the elongation if we compare with the as cast (non alloy ductile iron). The higher impact energy value obtained at 9000 C austenization and 375o C austempering temperatures during 60 minutes holding times. The …

The Manufacturing Properties Of Galvanised Steel Sheet With Hexagonal And Tetragonal Network Of Circle Holes, Rahmat Saptono

Makara Journal of Technology

Galvanized steel sheet of 0.8 mm in thickness was drilled with circle holes of 2.5 mm diameter and spacing arranged in tetragonal and hexagonal pattern. The manufacturing properties of specimen were studied through drawing and stretching simulative test. It was concluded from the results that, at high ratio of punch to hole diameter (40/2.5), the drawing properties (LDR) of both square and hexagonal perforated sheet were slightly lower than that of solid sheet, while hexagonal perforated showing LDR somewhat higher than the square one. The stretching properties (LDH) of sheet, however, were much lower than that of solid sheet while …

Develops The Software Of Dsp Processor For The Cdma Circuitry, Arman Djohan D.

Makara Journal of Technology

This research develops the software of DSP Processor type TMS320C54X for the CDMA circuitry. This research apply two algorithms namely Mathematic Algorithm and table lookup Algorithm. From both algorithms, the research examine what algorithm have the fasted processing time and the smallest memory occupation. From the examination results the Mathematic Algorithm have 20.62 milliseconds processing time and the Table lookup algorithm have 14.08 milliseconds processing time. The Table lookup algorithm have the fastest processing time because the Matematic algorithm need the rounding process of the fi gure. Eventhough such processing time is not exceed from the 125 millisecond of delay …

From Linear To Nonlinear Control Means: A Practical Progression, Zhiqiang Gao

Electrical and Computer Engineering Faculty Publications

With the rapid advance of digital control hardware, it is time to take the simple but effective proportional-integral-derivative (PID) control technology to the next level of performance and robustness. For this purpose, a nonlinear PID and active disturbance rejection framework are introduced in this paper. It complements the existing theory in that (1) it actively and systematically explores the use of nonlinear control mechanisms for better performance, even for linear plants; (2) it represents a control strategy that is rather independent of mathematical models of the plants, thus achieving inherent robustness and reducing design complexity. Stability analysis, as well as …

Embedded Software Programming To Develop A Command Line User Interface For Monitoring And Debugging A Manually Driven Gas Regulator Control System, Syed N. Hyder

Electrical & Computer Engineering Theses & Dissertations

This thesis presents a complete embedded programming model and software codes for a command-line user interface for CONCOA's gas regulator control system. Control Corporation of America (CONCOA) manufactures high-pressure gas regulators, which mechanically control the pressure at their outlets. Since the control system is based on mechanical regulators, adding or stopping gas flow from the system can cause manifold fluctuation that could further cause the pressure to rise or fall with time. The main motivation for developing a command line user interface is to provide a centralized computer control to monitor and debug the gas regulator control system electronically by …

Traffic Simulation Using Arena, Shanti Yelamanchi

Electrical & Computer Engineering Theses & Dissertations

Many traffic simulation tools exist for developing traffic simulations; these tools can be divided broadly into two categories — macro simulation tools and micro simulation tools. These two categories of simulation tools are directed at modeling the extremes of traffic systems: very large systems and very small systems. There is a class of intermediate-sized transportation networks for which neither category of simulation tools might perform adequately. Additionally these specialized traffic simulation tools have a high learning curve. For developing medium sized traffic simulations in a short period of time, one might choose to use a familiar general-purpose discrete event simulation …

Improvements In Wavelength Modulation Spectroscopy Using Ratios Of Higher Harmonics, James Michael Barrington

Electrical & Computer Engineering Theses & Dissertations

Experiments in Wavelength Modulation Spectroscopy have been conducted at Old Dominion University since 1996. The method provides a highly sensitive, nonintrusive method of probing gases. Research has concentrated on effectively modeling the higher harmonic shapes that are measured experimentally. Accurately modeling these signals will result in the ability to reliably extract the information contained in transition line shapes.

In order to accurately depict the signals, the theory must be thoroughly understood. This thesis develops the theory of Wavelength Modulation Spectroscopy from two aspects: a direct Fourier series expansion of a time varying intensity profile and through communication theory. In addition, …

A Study Of Radiofrequency Effects On Gene Expression, Elizabeth A. Coln

Electrical & Computer Engineering Theses & Dissertations

Numerous studies have been completed over the past several years to look at the non-thermal effects of low-level radiofrequency exposure on biological systems. These studies were done to determine if exposure to radiofrequency fields are safe, or if they may lead to health problems or changes to any of the biological processes continually occurring within the human body. Responses measured include stress responses (I), gene expression (2), cell proliferation (3), cell morphology (4), and changes in DNA (5).

Dispersion is the most common model for explaining the electric behavior of biomaterials. It refers to the corresponding frequency domain concept of …

A Formal Object Model For Layered Networks To Support Verification And Simulation, Rasha M. B. E. Morsi

Electrical & Computer Engineering Theses & Dissertations

This work presents an abstract formal model of the interconnection structure of the Open Systems Interconnection Reference Model (OSI-RM) developed using Object-Oriented modeling principles permitting it to serve as a re-usable platform in supporting the development of simulations and formal methods applied to layered network protocols. A simulation of the object model using MODSIM III was developed and Prototype Verification System (PVS) was used to show the applicability of the object model to formal methods by formally specifying and verifying a Global Systems for Mobile communications (GSM) protocol. This application has proved to be successful in two aspects. The first …

Robust Face Representation And Recognition Under Low Resolution And Difficult Lighting Conditions, Mohammad Moinul Islam

Electrical & Computer Engineering Theses & Dissertations

This dissertation focuses on different aspects of face image analysis for accurate face recognition under low resolution and poor lighting conditions. A novel resolution enhancement technique is proposed for enhancing a low resolution face image into a high resolution image for better visualization and improved feature extraction, especially in a video surveillance environment. This method performs kernel regression and component feature learning in local neighborhood of the face images. It uses directional Fourier phase feature component to adaptively lean the regression kernel based on local covariance to estimate the high resolution image. For each patch in the neighborhood, four directional …

Fabrication Techniques For Iii-V Micro-Opto-Electro-Mechanical Systems, Jeremy A. Raley

Theses and Dissertations

This thesis studies selective etching techniques for the development of Al_xGa_1-xAs micro-opto-electro-mechanical systems (MOEMS). New MEMS technology based on materials such as Al_xGa_1-xAs enables the development of micro-systems with embedded active micro-optical devices. Tunable micro-lasers and optical switching based on MOEMS technology will improve future wavelength division multiplexing (WDM) systems. WDM vastly increases the speed of military communications and sensor data processing. From my designs, structures are prepared by molecular beam epitaxy. I design a mask set for studies of crystal plane selectivity. I perform a series of experiments on the selective …

Thin Film Interference Filters For 25ghz Channel Spacing, M. A. Scobey, R. M. Fortenberry, L. F. Stokes, W. P. Kastanis, Dennis J. Derickson

Electrical Engineering

No abstract provided.

Evaluation And Analysis Of Array Antennas For Passive Coherent Location (Pcl) Systems, Baris Calikoglu

Theses and Dissertations

Passive Coherent Location (PCL) systems use a special form of a radar receiver that exploits the ambient radiation in the environment to detect and track targets. Typical transmissions of opportunity that might be exploited include television and FM radiobroadcasts. PCL implies the use of a non-radar electromagnetic sources of illumination, such as commercial radio or television broadcasts also referred as transmitters of opportunity. The use of such illumination sources means that the receiver needs to process waveforms that are not designed for radar purposes. As a consequence, the receivers for PCL systems must be much more customized than traditional receivers, …

Genetic Routing Algorithms To Optimize Availability In Broadband Wireless Networks With Load Balancing, William S. Hortos

Electrical Engineering and Computer Science Faculty Publications

Packet-switched networks using the Internet Protocol (IP) provide multimedia services through broadband wireless access to mobile and fixed subscribers from an IP core network via bi-directional paths consisting of a hierarchy of high-speed routers, switches, and servers. Packets are aggregated at the nodes that form the ordered links of end-to-end paths between subscriber and gateway. Network resources are allocated at nodes to meet quality of service (QoS) requirements of new and existing calls. If sufficient resources are not available to satisfy a call's QoS, the call is blocked or dropped, reducing network "uptime" or availability. Packet flows are shared among …

Microelectronics Process Engineering At San Jose State University: A Manufacturing-Oriented Interdisciplinary Degree Program, Emily Allen, Stacy H. Gleixner, David W. Parent, Greg Young, Yasser Dessouky, Linda Vanasupa

Faculty Publications

San Jose State University's new interdisciplinary curriculum in Microelectronics Process Engineering is described. This baccalaureate program emphasizes hands-on thin-film fabrication experience, manufacturing methods such as statistical process control, and fundamentals of materials science and semiconductor device physics. Each course of the core laboratory sequence integrates fabrication knowledge with process engineering and manufacturing methods. The curriculum development process relies on clearly defined and detailed program and course learning objectives. We also briefly discuss our strategy of making process engineering experiences accessible for all engineering students through both Lab Module and Statistics Module series.

Efficient Modeling Of Discontinuities And Dispersive Media In Printed Transmission Lines, R. Araneo, Chen Wang, Xiaoxiong Gu, James L. Drewniak, S. Celozzi

Electrical and Computer Engineering Faculty Research & Creative Works

The finite-difference time-domain method is applied to the analysis of transmission lines on printed circuit boards. The lossy, dispersive behavior of the dielectric substrate is accurately accounted for by means of several algorithms whose accuracy is discussed and compared. Numerical results are validated by comparisons with measurements and an equivalent circuit of slot in the ground plane is proposed.

Space Time Adaptive Processing And Clutter Classification Integration And Evaluation, Nathan A. Jensen

Theses and Dissertations

Radar is a fundamental technology in today's military and civilian environment, and continuing development of this technology is of utmost importance to maintaining technological advantages this realm. Current radar technologies suffer from jamming and clutter limitations. STAP is a statistical method to remove this noise, however it is extremely computationally intensive, and presents several real time processing hurdles. Clutter Classification is another method to classify the radar returns that are found according to the best fit statistical distribution that the return follows. This research investigation attempts to use this clutter classification technology to aid in the detection of targets by …

Ambiguity Function Analysis And Direct-Path Signal Filtering Of The Digital Audio Broadcast (Dab) Waveform For Passive Coherent Location (Pcl), Abdulkadir Guner

Theses and Dissertations

This research presents an ambiguity function analysis of the digital audio broadcast (DAB) waveform and one signal detection approach based on signal space projection techniques that effectively filters the direct-path signal from the receiver target channel. Currently, most Passive Coherent Location (PCL) research efforts are focused and based on frequency modulated (FM) radio broadcasts and analog television (TV) waveforms. One active area of PCL research includes the search for new waveforms of opportunity that can be exploited for PCL applications. As considered for this research, one possible waveform of opportunity is the European digital radio standard DAB. For this research, …

Wavelet Domain Communication System (Wdcs): Packet-Based Wavelet Spectral Estimation And M-Ary Signaling, Marion Jay F. Lee

Theses and Dissertations

A recently proposed Wavelet Domain Communication System (WDCS) using transform domain processing demonstrated excellent interference avoidance capability under adverse environmental conditions. This work extends previous results by: 1) incorporating a wavelet packet decomposition technique, 2) demonstrating M-Ary signaling capability, and 3) providing increased adaptivity over a larger class of interference signals. The newly proposed packet-based WDCS is modeled and its performance characterized using MATLAB®. In addition, the WDCS response to two scenarios simulating Doppler effects and physical separation of transceivers are obtained. The fundamental metric for analysis and performance evaluation is bit error rate (P_b). Relative to …

Microdot - A Four-Bit Microcontroller Designed For Distributed Low-End Computing In Satellites, Anthony R. Woodcock

Theses and Dissertations

Many satellites are an integrated collection of sensors and actuators that require dedicated real-time control. For single processor systems, additional sensors require an increase in computing power and speed to provide the multi-tasking capability needed to service each sensor. Faster processors cost more and consume more power, which taxes a satellite's power resources and may lead to shorter satellite lifetimes. An alternative design approach is a distributed network of small and low power microcontrollers designed for space that handle the computing requirements of each individual sensor and actuator. The design of microdot, a four-bit microcontroller for distributed low-end computing, is …

Statistical Error Analysis Of A Doa Estimator For A Pcl System Using The Cramer-Rao Bound Theorem, Kerim Say

Theses and Dissertations

Direction of Arrival (DOA) estimation of signals has been a popular research area in Signal Processing. DOA estimation also has a significant role in the object location process of Passive Coherent Location (PCL) systems. PCL systems have been in open literature since 1986 and their applications are not as clearly understood as the DOA estimation problem. However, they are the focus of many current research efforts and show much promise. The purpose of this research is to analyze the DOA estimation errors in a PCL system. The performance of DOA estimators is studied using the Cramer-Rao Bound (CRB) Theorem. The …

Development And Characterization Of An Emergency Communications System Using Near Vertical Incident Skywave Antennas, Richard A. Allnutt

Theses and Dissertations

The NVIS system characterized in this work was designed to eliminate skip propagation by optimizing the design for contiguous coverage. The NVIS technique involves use of transmission and receiving antennas that create nearly vertical propagation and continuous coverage from the transmitter to a distance of 200 miles. Man portable, very low power transceivers (5 watts maximum) and horizontal dipole antennas five feet above the ground are used in an NVIS communication system for this work. The system is designed for the purpose of supporting communication with emergency workers in areas where other communication is difficult. Digital and analog effectiveness are …

Translation And Rotation Invariant Multiscale Image Registration, Jennifer L. Manfra

Theses and Dissertations

The most recent research involved registering images in the presence of translations and rotations using one iteration of the redundant discrete wavelet transform. We extend this work by creating a new multiscale transform to register two images with translation or rotation differences, independent of scale differences between the images. Our two-dimensional multiscale transform uses an innovative combination of lowpass filtering and the continuous wavelet transform to mimic the two-dimensional redundant discrete wavelet transform. This allows us to obtain multiple subbands at various scales while maintaining the desirable properties of the redundant discrete wavelet transform. Whereas the discrete wavelet transform produces …

Determination Of The Possible Locations Of The Receiver On A Passive Coherent Location System, Considering The Effects Of The Terrain And The Atmospheric Conditions, Carlos A. Meier

Theses and Dissertations

It has always been an issue for an armed force, or government, to obtain complete radar coverage over an area of interest. Generally, this objective remains unaccomplished due to geographical, technical, and/or operational reasons (meaning topographic obstacles, transmitted power, extreme isolation, hierarchy of objectives, etc.) The fact of having vast areas of territory beyond radar coverage can be decisive in an armed conflict. With the recent resurgence of bistatic radar theory and applications, now in the form of Passive Coherent Location (PCL) systems, using existing signal sources (TC and Radio Stations) it is possible to decrease the blind zones of …

The Analysis Of Sophisticated Direction Of Arrival Estimation Methods In Passive Coherent Locators, Ahmet Ozcetin

Theses and Dissertations

In passive coherent locators (PCL) systems, noise and the precision of direction of arrival (DOA) estimation are key issues. This thesis addresses the implementation of sophisticated DOA estimation methods, in particular the multiple signal classification (MUSIC) algorithm, the conventional beam forming (CBF) algorithm, and the algebraic constant modulus algorithm (ACMA). The goal is to compare the ACMA to the MUSIC, and CBF algorithms for application to PCL. The results and analysis presented here support the use of constant modulus information, where available, as an important addition to DOA estimation. The ACMA offers many simple solutions to noise and separation related …

A Stable Self-Tuning Fuzzy Logic Control System For Industrial Temperature Regulation, Zhiqiang Gao, Thomas A. Trautzsch, James G. Dawson

Electrical and Computer Engineering Faculty Publications

A closed-loop control system incorporating fuzzy logic has been developed for a class of industrial temperature control problems. A unique fuzzy logic controller (FLC) structure with an efficient realization and a small rule base that can be easily implemented in existing industrial controllers was proposed. The potential of FLC in both software simulation and hardware test in an industrial setting was demonstrated. This includes compensating for thermo mass changes in the system, dealing with unknown and variable delays, operating at very different temperature set points without retuning, etc. It is achieved by implementing, in the FLC, a classical control strategy …

Diagnostics Of Bar And End-Ring Connector Breakage Faults In Polyphase Induction Motors Through A Novel Dual Track Of Time-Series Data Mining And Time-Stepping Coupled Fe-State Space Modeling, Richard J. Povinelli, John F. Bangura, Nabeel Demerdash, Ronald H. Brown

Electrical and Computer Engineering Faculty Research and Publications

This paper develops the fundamental foundations of a technique for detection of faults in induction motors that is not based on the traditional Fourier transform frequency domain approach. The technique can extensively and economically characterize and predict faults from the induction machine adjustable speed drive design data. This is done through the development of dual-track proof-of-principle studies of fault simulation and identification. These studies are performed using our proven Time Stepping Coupled Finite Element-State Space method to generate fault case data. Then, the fault cases are classified by their inherent characteristics, so-called “signatures” or “fingerprints.” These fault signatures are extracted …

An Analysis Of Mutually Dispersive Brown Symbols For Non-Linear Ambiguity Suppression, Matthew J. Papaphotis

Theses and Dissertations

This thesis significantly advances research towards the implementation of optimal Non-linear Ambiguity Suppression (NLS) waveforms by analyzing the Brown theorem. The Brown theorem is reintroduced with the use of simplified linear algebraic notation. A methodology for Brown symbol design and digitization is provided, and the concept of dispersive gain is introduced. Numerical methods are utilized to design, synthesize, and analyze Brown symbol performance. The theoretical performance in compression and dispersion of Brown symbols is demonstrated and is shown to exhibit significant improvement compared to discrete codes. As a result of this research a process is derived for the design of …

Design And Fabrication Of Micro-Electro-Mechanical Structures For Tunable Micro-Optical Devices, Michael C. Harvey

Theses and Dissertations

Tunable micro-optical devices are expected to be vital for future military optical communication systems. In this research I seek to optimize the design of a microelectromechanical (MEM) structure integrated with a III-V semiconductor micro-optical device. The resonant frequency of an integrated optical device, consisting of a Fabry-Perot etalon or vertical cavity surface emitting laser (VCSEL), may be tuned by applying an actuation voltage to the MEM Flexure, thereby altering the device's optical cavity length. From my analysis I demonstrate tunable devices compatible with conventional silicon 5V integrated circuit technology. My design for a Fabry-Perot etalon has a theoretical tuning range …