Mechanical Engineering Commons^™

Multipacting Optimization Of A 750 Mhz Rf Dipole, A. Castilla, J. R. Delayen

Physics Faculty Publications

Crab crossing schemes have been proposed to re-instate luminosity degradation due to crossing angles at the interaction points in next generation colliders to avoid the use of sharp bending magnets and their resulting large synchrotron radiation generation, highly undesirable in the detector region. The rf dipole has been considered for a different set of applications in several machines, both rings and linear colliders. We present in this paper a study of the effects on the multipacting levels and location depending on geometrical variations on the design for a crabbing/deflecting application in a high current (3/0.5 A), high repetition (750 MHz) …

Impact Of Fracture Spacing And Mechanical Parameter Anisotropy On Fracture Width In Horizontal Wells In Shales, Deepak Gokaraju

Masters Theses

"The success of economically viable production of oil and gas from ultra-low permeability shale reservoirs depends on the creation of an extensive fracture network through hydraulic fracture stimulation. Multiple hydraulic fractures are created simultaneously in each stage to increase the surface area of contact between the wellbore and reservoir. The spacing between fractures is an important component to consider when developing an optimum stimulation design. An important aspect of shale rock properties is that shales are inherently anisotropic with a horizontal plane of isotropy (transversely isotropic) due to their finely layered structure. This study aims to provide an insight into …

Educational Programmes For Spatial Information Sciences In The Technological University Of Dublin, William Prendergast, Eamonn Murphy, Audrey Martin, Avril Behan

Conference papers

The ever increasing spatial information needs of society, the rapid development of new surveying technologies, and the global demand for appropriately qualified surveyors, have triggered a radical re-evaluation of geomatics education worldwide. Significant enhancements have been made to the educational programmes in the spatial information science discipline in the Technological University of Dublin’s (DIT) during the last decade including the provision of a BSc in Geomatics and various masters’ programmes to cater for the increasingly specialised needs of the Geographic Information sector in Ireland.

Bio-Inspired Flow Sensing For Underwater Guidance And Navigation, Levi Devries

Link Foundation Ocean Engineering and Instrumentation Fellowship Reports

Stream-dwelling fish and aquatic mammals have an innate ability to navigate often-tumultuous environments with impressive precision, a highly desirable trait for underwater vehicle applications. For example, trout use their lateral line to sense vortices shed by an upstream obstacle and slalom between the vortices to reduce energy expenditure compared to free-stream swimming [3]. Moreover, harbor seals can use their whiskers to follow the trail of flow disturbances created in the wake of an object that has passed minutes before [4]. Recent developments in materials science have produced sensors that can measure local flow velocity similar to seal whiskers, and integration …

Biomechanical Strain As A Trigger For Pore Formation In Schlemm’S Canal Endothelial Cells, Sietse T. Braakman, Ryan M. Pedrigi, A. Thomas Read, James A. E. Smith, W. Daniel Stamer, C. Ross Ethier, Darryl R. Overby

Department of Mechanical and Materials Engineering: Faculty Publications

The bulk of aqueous humor passing through the conventional outflow pathway must cross the inner wall endothelium of Schlemm’s canal (SC), likely through micron-sized transendothelial pores. SC pore density is reduced in glaucoma, possibly contributing to obstructed aqueous humor outflow and elevated intraocular pressure (IOP). Little is known about the mechanisms of pore formation; however, pores are often observed near dome-like cellular outpouchings known as giant vacuoles (GVs) where significant biomechanical strain acts on SC cells. We hypothesize that biomechanical strain triggers pore formation in SC cells. To test this hypothesis, primary human SC cells were isolated from three non-glaucomatous …

Altered Mechanobiology Of Schlemm’S Canal Endothelial Cells In Glaucoma, Darryl R. Overby, Enhua H. Zhou, Rocio Vargas-Pinto, Ryan M. Pedrigi, Rudolf Fuchshofer, Sietse T. Braakman, Ritika Gupta, Kristin M. Perkumas, Joesph M. Sherwood, Amir Vahabikashi, Quynh Dang, Jae Hun Kim, C. Ross Ethier, W. Daniel Stamer, Jeffrey J. Fredberg, Mark Johnson

Department of Mechanical and Materials Engineering: Faculty Publications

Increased flow resistance is responsible for the elevated intraocular pressure characteristic of glaucoma, but the cause of this resistance increase is not known. We tested the hypothesis that altered biomechanical behavior of Schlemm’s canal (SC) cells contributes to this dysfunction. We used atomic force microscopy, optical magnetic twisting cytometry, and a unique cell perfusion apparatus to examine cultured endothelial cells isolated from the inner wall of SC of healthy and glaucomatous human eyes. Here we establish the existence of a reduced tendency for pore formation in the glaucomatous SC cell—likely accounting for increased outflow resistance—that positively correlates with elevated subcortical …

Extracting Continuum-Like Deformation And Stress From Molecular Dynamics Simulations, Lili Zhang, John Jasa, George Gazonas, Antoine Jerusalem, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

We present methods that use results from molecular dynamics (MD) simulations to construct continuum parameters, such as deformation gradient and Cauchy stress, from all or any part of an MD system. These parameters are based on the idea of minimizing the difference between MD measures for deformation and traction and their continuum counterparts. The procedures should be applicable to non-equilibrium and inhomogeneous systems, and to any part of a system, such as a polymer chain. The resulting procedures provide methods to obtain first and higher order deformation gradients associated with any subset of the MD system, and associated expressions for …

Polymer Aggregation Correlated Transition From Schottky-Junction To Bulk Heterojunction Organic Solar Cells, Bin Yang, Zhengguo Xiao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

The fullerene-based organic Schottky-junction solar cells have recently attracted intensive research interest because of their unique electrical performance, such as significant photocurrent generation from excitons created in fullerenes and large open-circuit voltage (V_OC) output induced by high Schottky-barrier height between the anode and the fullerene acceptor. This manuscript reports another remarkably appealing advantage that the fullerene-based Schottky-junction solar cells are more stable than the bulk heterojunction counterparts. The better stability is likely due to mitigative polymer photo-oxidation and/or little morphological change of active film in the aged Schottky-junction devices. The transition from Schottky-junction to bulk heterojunction appears at …

Numerical Simulations Of Dynamic Behavior Of Polyurea Toughened Steel Plates Under Impact Loading, Chien-Chung Chen, Daniel G. Linzell

Department of Civil and Environmental Engineering: Faculty Publications

The objective of the work discussed herein is to develop a nonlinear 3D finite element model to simulate dynamic behavior of polyurea toughened steel plates under impact loading. Experimental and numerical work related to model development are presented. Material properties are incorporated into numerical models to account for strain-rate effects on the dynamic behavior of polyurea and steel. One bare steel plate and four polyurea toughened steel plates were tested under impact loading using a pendulum impact device. Displacement time-history data from experimental work was used to validate the numerical models. Details on material model construction, finite element model development, …

Comparison Of Magnetic Probe Calibration At Nano And Millitesla Magnitudes, Ryan A. Pahl, Joshua L. Rovey, David Pommerenke

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Magnetic field probes are invaluable diagnostics for pulsed inductive plasma devices where field magnitudes on the order of tenths of tesla or larger are common. Typical methods of providing a broadband calibration of Ḃ probes involve either a Helmholtz coil driven by a function generator or a network analyzer. Both calibration methods typically produce field magnitudes of tens of microtesla or less, at least three and as many as six orders of magnitude lower than their intended use. This calibration factor is then assumed constant regardless of magnetic field magnitude and the effects of experimental setup are ignored. This work …

Adaptive Control Of Uncertain Systems With Gain Scheduled Reference Models And Constrained Control Inputs, Mehrdad Pakmehr, Tansel Yucelen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper develops a new state feedback model reference adaptive control approach for uncertain systems with gain scheduled reference models in a multi-input multi-output (MIMO) setting with constrained control inputs. A single Lyapunov matrix is computed for multiple linearization of the nonlinear closed loop gain scheduled reference system, using convex optimization tools. This approach guarantees stability of the closed loop gain scheduled reference model. Adaptive state feedback control architecture is then developed, and its stability is proven for the case with constrained control inputs. The resulting closed-loop system is shown to have bounded solutions with bounded tracking error, with the …

Thermal-Electromagnetic Analysis Of Infrared Antennas, Edward C. Kinzel, Brian Slovick, James Ginn, Brian Lail, Glenn Boreman

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Antenna-coupled Metal-Oxide-Metal (MOM) diodes have been demonstrated for sensing and proposed for energy harvesting at THz, infrared, and even visible frequencies. The design of the antenna allows engineering of the response of the device with respect to polarization, wavelength and angle of incidence. The classic understanding of the antenna coupled MOM diode is that the electric field generated by the antenna causes electrons to tunnel through the barrier oxide. This is supported by the fact that when the oxide separates metals with different work functions, a properly polarized field can produce an asymmetric tunnel current under zero bias. Losses in …

Verifiable Frequency-Limited Adaptive Control Performance Based On Linear Matrix Inequalities, Mario Luca Fravolini, Tansel Yucelen, Daniel Wagner, Ali Albattat, Paolo Valigi

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Adaptive controllers are often criticized for the lack of clear and easy verification procedures that relate design parameters to time domain performance especially during transients. For this reason, it is a challenge to rigorously certify existing adaptive control algorithms. To that end, we propose a validation framework where stability and performance requirements are formulated in terms of Linear Matrix Inequalities. This brings the advantage that adaptive controller design and verification can be analyzed and optimized via the solution of a convex optimization whose objective is to guarantee the evolution of the error components within an a-priori specified domain. This approach …

The Effect Of Different Rollover Conditions Of The Vibrator On Human Injury, Qin Li, Hang Liu, Zhiqiang Huang, Yaping Ding, Xiaoping Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Vibrator, as a crucial vehicle of oil and gas exploration, is challenged by the complex terrains. The probability of rollover accident is therefore high in bumpy terrain in which the drivers' life is seriously threatened. Finite element numerical analysis was used to study the injury of the driver's head, neck and chest in the rollover accidents of domestic KZ-28 type vibrator on different conditions. The injuries of three parts were evaluated based on the human injury criteria. Driver's safety on different rollover conditions was comparatively analyzed. The results indicated that the injury degree of human head caused by vibrator rollover …

Decomposition Of Ionic Liquid Ferrofluids For Multi-Mode Spacecraft Propulsion, Steven P. Berg, Brynne Coleman, Joshua L. Rovey

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Ionic liquid ferrofluids based on mixtures of [Emim][EtSO4] and [Bmim][NO3] fuels and hydroxylammonium nitrate oxidizer were synthesized by adding iron oxide nanoparticles. The resulting propellants were then tested for decomposition capability. Spot plate testing indicated that the temperature required to initiate rapid decomposition dropped from 115 °C to 75 °C with a 30% by weight addition of iron oxide for the [Bmim][NO3] propellant. Adding more iron oxide resulted in an increase in onset temperature. The [Emim][EtSO4] propellant had a much lower decrease in onset temperature, bottoming out at 90 °C. Batch reactor tests under vacuum showed that 10% addition of …

Predicting Pressure Distribution Between Transfemoral Prosthetic Socket And Residual Limb Using Finite Element Analysis, Rajesh Surapureddy

UNF Graduate Theses and Dissertations

In this study, a non-linear Finite Element (FE) model was created and analyzed to determine the pressure distribution between the residual limb and the prosthetic socket of a transfemoral amputee. This analysis was performed in an attempt to develop a process allowing healthcare providers and engineers to simulate the fit and comfort of transfemoral prosthetics to reduce the number of re-fittings needed for the amputees. The analysis considered the effects of interference due to insertion of the limb into the prosthesis, referred to as donning, and also the effects due to the body weight of the amputee. A non-linear finite …

Probabilistic Engineering Analysis And Design Under Time-Dependent Uncertainty, Zhen Hu

Doctoral Dissertations

"Time-dependent uncertainties, such as time-variant stochastic loadings and random deterioration of material properties, are inherent in engineering applications. Not considering these uncertainties in the design process may result in catastrophic failures after the designed products are put into operation. Although significant progress has been made in probabilistic engineering design, quantifying and mitigating the effects of time-dependent uncertainty is still challenging. This dissertation aims to help build high reliability into products under time-dependent uncertainty by addressing two research issues. The first one is to efficiently and accurately predict the time-dependent reliability while the second one is to effectively design the time-dependent …

A Study Of Walkway Safety And Evaluation Of Tribological Test Equipment, Henry Thomas Baker

UNF Graduate Theses and Dissertations

A walkway tribometer measures the coefficient of friction between flooring material and a test foot. The value of the coefficient of friction is an indicator as to whether the flooring surface is slippery and has a propensity to cause slip and falls. This study determined that one style of tribometer, an XL Tribometer, mimics the heel-to-floor interaction of the human heel strike. High speed video footage revealed that the test foot strikes the surface and rotates so that full engagement occurs before sliding thus mimicking the affect of a human ankle. The test foot accelerates forward as would be expected …

Role Of Surface Chemistry In Nanoscale Electrokinetic Transport, Secuk Atalay

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation work presents the efforts to study the electrofluidics phenomena, with a focus on surface charge properties in nanoscale systems with the potential applications in imaging, energy conversion, ultrafiltration, DNA analysis/sequencing, DNA and protein transport, drug delivery, biological/chemical agent detection and micro/nano chip sensors.

Since the ion or molecular or particle transport and also liquid confinement in nano-structures are strongly dominated by the surface charge properties, in regards of the fundamental understanding of electrofluidics at nanoscale, we have used surface charge chemistry properties based on 2-pK charging mechanism. Using this mechanism, we theoretically and analytically showed the surface charge …

Mechanistic Identification Of Specific Force Coefficients In Endmilling Inconel 718 Under Four Cooling Strategies, Mahmood Shaman Ameen

Masters Theses

“This thesis presents the results of experimental investigations of the mechanistic identification of specific force coefficients for uncoated bull-nose and uncoated wavy-edge/bull-nose helical endmilling of Inconel 718 under emulsion, minimum quantity lubrication (MQL), cryogenic (LN₂), and combined (MQL + LN₂) cooling. Several slot milling tests were conducted on Inconel 718 workpiece block with depth of cut 1.25 mm. The cutting parameters were varied as: spindle speed, n = 250 and 750 rev/min, feedrate, f = 25–75 mm/min by using uncoated carbide bull-nose helical endmill. Also 24 peripheral milling tests were conducted on Inconel 718 workpiece block …