Mechanical Engineering Commons^™

Computational Flow Analysis Of A Flapping Micro-Flyer Wing For Cycle-Averaged Force Production, Nitesh Rajendra Rajput

Mechanical and Aerospace Engineering Theses - Archive

Human engineers have been trying long to mimic creations of nature for their own benefits. One such area of interest is the insect based micro flapping wing flyers for their wide employment in commercial as well as military applications. These micro air vehicles (MAVs) are capable of performing acts that can be too dangerous for humans to perform, such as tactical reconnaissance in a combat zone. The maneuverability required of these MAVs call for a careful design and thorough study of their aerodynamic performance. This research goal is to provide an estimation of the forces generated during the flapping motion …

Scaling Laws For Radial Foil Bearings, Srikanth Honavara Prasad

Mechanical and Aerospace Engineering Theses - Archive

The effects of fluid pressurization, structural deformation of the compliant members and heat generation in foil bearings make the design and analysis of foil bearings very complicated. The complex fluid-structural-thermal interactions in foil bearings also make modeling efforts challenging because these phenomena are governed by highly non-linear partial differential equations. Consequently, comparison of various bearing designs require detailed calculation of the flow fields (velocities, pressures), bump deflections (structural compliance) and heat transfer phenomena (viscous dissipation in the fluid, frictional heating, temperature profile etc.,) resulting in extensive computational effort(time/hardware). To obviate rigorous computations and aid in feasibility assessments of foil bearings …

Model Block Press, Jordan Brown, Michael Evans, Connor Morrow

Mechanical Engineering

The Center for Vocational Building Technology came to the Mechanical Engineering department at Cal Poly, San Luis Obispo with a project to create a new, less expensive model block press than their current BP9 design. This press would produce ¼ scale model compressed earth blocks to be sold as souvenirs and used in demonstrations for constructing buildings. After analyzing the design of the current block presses, JCM came up with the BP10 design. The BP10 operates similarly to the larger block presses, but will cost significantly less to produce and will have some of the design features enhanced to make …

Low Cost Flow Sensing For Field Sprayers, Yue Zhang

Theses and Dissertations--Biosystems and Agricultural Engineering

Precisely measuring the flow rate in sprayers is a key technology to precision agriculture. With the development of advanced technologies, the demand for the ability to measure flow rate of individual nozzle has become more important and urgent.

This paper investigates the possibility of developing a low-cost flow rate measurement technique. The technique is based on analyzing the acoustic signal from a microphone placed near the nozzle tip. A comparison between acoustic signal and vibration signal was made to study the relations between them. Then several possible locations of the microphone for measuring flow rate were tested and compared, and …

Computational Investigation Of Injectable Treatment Strategies For Myocardial Infarction, Hua Wang

Theses and Dissertations--Mechanical and Aerospace Engineering

Heart failure is an important medical disease and impacts millions of people throughout the world. In order to treat this problem, biomaterial injectable treatment injected into the myocardium of the failing LV are currently being developed. Through this treatment, the biomaterial material injections can reduce wall stresses during the cardiac remodeling process. By using computational techniques to analyze the effects of a treatment involving the injection of biomaterial material into the LV after MI, the material parameters of the hydrogel injections can be optimized. The results shows that the hydrogel injections could reduce the global average fiber stress and the …

An Analysis Of Energy Resources Utilization For Two Metal Joining Manufacturing Processes, Jonathan Gasser

Theses and Dissertations--Mechanical and Aerospace Engineering

Sustainable manufacturing involves utilizing energy resources efficiently. Currently, the state of sustainability for a given manufacturing process is described by most in a qualitative sense as opposed to using quantitative metrics. This thesis offers a segment of analysis needed to understand the state of sustainability in the context of energy resource utilization. This was accomplished by measuring the order of magnitude difference between the energy consumption of a manufacturing process vs. the theoretical minimum amount of energy required to complete the same task (aluminum T-joint bond). This analysis was completed for a TIG welding process and a controlled atmosphere brazing …

Axial Compressor Flow Behavior Near The Aerodynamic Stability Limit, Bradley D. Butler

Theses and Dissertations--Mechanical and Aerospace Engineering

In this investigation, casing mounted high frequency response pressure transducers are used to characterize the flow behavior near the aerodynamic stability limit of a low speed single stage axial flow compressor. Time variant pressure measurements are acquired at discrete operating points up to the stall inception point and during the transition to rotating stall, for a length of time no shorter than 900 rotor revolutions. The experimental data is analyzed using multiple techniques in the time and frequency domains.

Experimental results have shown an increase in the breakdown of flow periodicity as the flow coefficient is reduced. Below a flow …

Theoretical Study Of Thermal Analysis Kinetics, Yunqing Han

Theses and Dissertations--Mechanical and Aerospace Engineering

In the past decades, a great variety of model fitting and model free (isoconversional) methods have been developed for extracting kinetic parameters for solid state reactions from thermally stimulated experimental data (TGA, DSC, DTA etc.). However, these methods have met with significant controversies about their methodologies. Firstly, model-fitting methods have been strongly criticized because almost any reaction mechanism can be used to fit the experimental data satisfactorily with drastic variations of the kinetic parameters, and no good criterion exists to tell which mechanism is the best choice. Secondly, previous model free methods originated from the isoconversional principle, which is often …

Investigation Of Drilling Performance In Cryogenic Drilling On Cfrp Composite Laminates, Tian Xia

Theses and Dissertations--Mechanical and Aerospace Engineering

In recent years, there has been a substantial growth in the application of carbon fiber reinforced plastic (CFRP) composite materials in automobile and aerospace industries due to their superior properties such as lightweight, high strength, excellent corrosion resistance, and minimal fatigue concerns. The present study evaluates the drilling performance of woven carbon fiber reinforced plastics under both dry and cryogenic cooling conditions using uncoated solid carbide drill with a through-hole for coolant application.

The effects of the cooling conditions and the cutting parameters on drilling performance in drilling CFRP were evaluated in terms of generated thrust force, torque, cutting edge …

Shape Memory Behavior Of Single And Polycrystalline Nickel Rich Nickel Titanium Alloys, Irfan Kaya

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTi is the most commonly used shape memory alloy (SMA) and has been widely used for bio-medical, electrical and mechanical applications. Nickel rich NiTi shape memory alloys are coming into prominence due to their distinct superelasticity and shape memory properties as compared to near equi-atomic NiTi shape memory alloys. Besides, their lower density and higher work output than steels makes these alloys an excellent candidate for aerospace and automotive industry. Shape memory properties and phase transformation behavior of high Ni-rich Ni₅₄Ti₄₆ (at.%) polycrystals and Ni-rich Ni₅₁Ti₄₉ (at.%) single-crystals are determined. Their properties are sensitive …

Finite Element Modeling And Fabrication Of An Sma-Smp Shape Memory Composite Actuator, Mohammad Souri

Theses and Dissertations--Mechanical and Aerospace Engineering

Shape memory alloys and polymers have been extensively researched recently because of their unique ability to recover large deformations. Shape memory polymers (SMPs) are able to recover large deformations compared to shape memory alloys (SMAs), although SMAs have higher strength and are able to generate more stress during recovery.

This project focuses on procedure for fabrication and Finite Element Modeling (FEM) of a shape memory composite actuator. First, SMP was characterized to reveal its mechanical properties. Specifically, glass transition temperature, the effects of temperature and strain rate on compressive response and recovery properties of shape memory polymer were studied. Then, …

Estimating Passive Material Properties And Fiber Orientation In A Myocardial Infarction Through An Optimization Scheme Using Mri And Fe Simulation, Dimitri Mojsejenko

Theses and Dissertations--Mechanical and Aerospace Engineering

Myocardial infarctions induce a maladaptive ventricular remodeling process that independently contributes to heart failure. In order to develop effective treatments, it is necessary to understand the way and extent to which the heart undergoes remodeling over the course of healing. There have been few studies to produce any data on the in-vivo material properties of infarcts, and much less on the properties over the time course of healing. In this paper, the in-vivo passive material properties of an infarcted porcine model were estimated through a combined use of magnetic resonance imaging, catheterization, finite element modeling, and a genetic algorithm optimization …

Precipitation, Orientation And Composition Effects On The Shape Memory Properties Of High Strength Nitihfpd Alloys, Emre Acar

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf high temperature shape memory alloys are attractive due to their high operating temperatures (>100 ^oC) and acceptable transformation strain compared to NiTi. However, NiTiHf has limitations due to their lack of ductility and low strength, resulting in poor shape memory properties. In this study, Pd has been added to NiTiHf alloys in an attempt to improve their shape memory behavior. A combined approach of quaternary alloying and precipitation strengthening was used.

The characterization of a Ni_45.3Ti_29.7Hf₂₀Pd₅ (at. %) polycrystalline alloy was performed in compression after selected aging treatments. Transmission electron …

A Design Pathfinder With Material Correlation Points For Inflatable Systems, Jared T. Fulcher

Theses and Dissertations--Mechanical and Aerospace Engineering

The incorporation of inflatable structures into aerospace systems can produce significant advantages in stowed volume to mechanical effectiveness and overall weight. Many applications of these ultra-lightweight systems are designed to precisely control internal or external surfaces, or both, to achieve desired performance. The modeling of these structures becomes complex due to the material nonlinearities inherent to the majority of construction materials used in inflatable structures. Furthermore, accurately modeling the response and behavior of the interfacing boundaries that are common to many inflatable systems will lead to better understanding of the entire class of structures. The research presented involved using nonlinear …

Combining Sustainable Value Stream Mapping And Simulation To Assess Manufacturing Supply Chain Network Performance, Daniel T. Sparks

Theses and Dissertations--Mechanical and Aerospace Engineering

Sustainable Value Stream Mapping (Sus-VSM) builds upon traditional VSM to capture additional sustainability aspects of the product flow, such as environmental and societal aspects. This work presents research to expand the utility of Sus-VSM to supply chain networks, develop a general approach towards improving supply chain sustainability, and examine the benefits of implementing simulation and a design of experiments (DOE) style analysis. Metrics are identified to assess economic, environmental, and societal sustainability for supply chain networks and visual symbols are developed for the Supply Chain Sus-VSM (SC Sus-VSM) to allow users to easily identify locations where sustainability can be improved. …

Numerical Analysis Of Droplet Formation And Transport Of A Highly Viscous Liquid, Peiding Wang

Theses and Dissertations--Mechanical and Aerospace Engineering

Drop-on-demand (DOD) inkjet print-head has a major share of the market due to simplicity and feasibility of miniature system. The efficiency of droplet generation from DOD print-head is a result of several factors, include viscosity, surface tension, nozzle size, density, driving waveform (wave shape, frequency, and amplitude), etc. Key roles in the formation and behavior of liquid jets and drops combine three dimensionless groups: Reynolds number, Weber number and Ohnesorge number. These dimensionless groups provide some bounds to the “printability” of the liquid. Adequate understanding of these parameters is essential to improve the quality of droplets and provide guidelines for …

Sustainable Lifetime Value Creation Through Innovative Product Design: A Product Assurance Model, K. Daniel Seevers

Theses and Dissertations--Mechanical and Aerospace Engineering

In the field of product development, many organizations struggle to create a value proposition that can overcome the headwinds of technology change, regulatory requirements, and intense competition, in an effort to satisfy the long-term goals of sustainability. Today, organizations are realizing that they have lost portfolio value due to poor reliability, early product retirement, and abandoned design platforms. Beyond Lean and Green Manufacturing, shareholder value can be enhanced by taking a broader perspective, and integrating sustainability innovation elements into product designs in order to improve the delivery process and extend the life of product platforms.

This research is divided into …

Filtered-Dynamic-Inversion Control For Fixed-Wing Unmanned Aerial Systems, Jon Mullen

Theses and Dissertations--Mechanical and Aerospace Engineering

Instrumented umanned aerial vehicles represent a new way of measuring turbulence in the atmospheric boundary layer. However, autonomous measurements require control methods with disturbance-rejection and altitude command-following capabilities. Filtered dynamic inversion is a control method with desirable disturbance-rejection and command-following properties, and this controller requires limited model information. We implement filtered dynamic inversion as the pitch controller in an altitude-hold autopilot. We design and numerically simulate the continuous-time and discrete-time filtered-dynamic-inversion controllers with anti-windup on a nonlinear aircraft model. Finally, we present results from a flight experiment comparing the filtered-dynamic-inversion controller to a classical proportional-integral controller. The experimental results show …

Investigation Of Filtering Methods For Large-Eddy Simulation, Weiyun Liu

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis focuses on the phenomenon of aliasing and its mitigation with two explicit filters, i.e., Shuman and Padé filters. The Shuman filter is applied to velocity components of the Navier--Stokes equations. A derivation of this filter is presented as an approximation of a 1-D “pure math” mollifier and extend this to 2D and 3D. Analysis of the truncation error and wavenumber response is conducted with a range of grid spacings, Reynolds numbers and the filter parameter, β. Plots of the relationship between optimal filter parameter β and grid spacing, L²-norm error and Reynolds number to suggest …

A Metrics-Based Sustainability Assessment Of Cryogenic Machining Using Modeling And Optimization Of Process Performance, Tao Lu

Theses and Dissertations--Mechanical and Aerospace Engineering

The development of a sustainable manufacturing process requires a comprehensive evaluation method and fundamental understanding of the processes. Coolant application is a critical sustainability concern in the widely used machining process. Cryogenic machining is considered a candidate for sustainable coolant application. However, the lack of comprehensive evaluation methods leaves significant uncertainties about the overall sustainability performance of cryogenic machining. Also, the lack of practical application guidelines based on scientific understanding of the heat transfer mechanism in cryogenic machining limits the process optimization from achieving the most sustainable performance.

In this dissertation, based on a proposed Process Sustainability Index (ProcSI …