Mechanical Engineering Commons^™

Accelerated Lattice Boltzmann Method For Colloidal Suspensions Rheology And Interface Morphology, Hassan Farhat

Wayne State University Dissertations

ABSTRACT

ACCELERATED LATTICE BOLTZMANN MODEL FOR COLLOIDAL SUSPENSIONS RHEOLOGY AND INTERFACE MORPHOLOGY

by

HASSAN FARHAT

July 2010

Advisor: Dr. Singh Trilochan

Co-Advisor: Dr. Joon Sang Lee

Major: Mechanical Engineering

Degree: Doctor of Philosophy

Colloids are ubiquitous in the food, medical, cosmetic, polymer, water purification and pharmaceutical industries. Colloids thermal, mechanical and storage properties are highly dependent on their interface morphology and their rheological behavior.

Numerical methods provide a cheap and reliable virtual laboratory for the study of colloids. However efficiency is a major concern to address when using numerical methods for practical applications.

This work introduces the main building-blocks for …

Study Of Microstructure Effect On The Thermal Properties Of Yttria-Stabilized-Zirconia Thermal Barrier Coatings Made By Atmospheric Plasma Spray And Pressing Machine, Monica Bohorquez De Silva

LSU Doctoral Dissertations

Thermal barrier coatings (TBCs) are used in gas turbine engines to achieve a higher working temperature and thus lead to better efficiency. Yttria-Stabilized-Zirconia (YSZ), a material with low thermal conductivity, is commonly used as the top coat layer to provide the thermal barrier effect. In this dissertation the thermo-physical properties of a variety of TBCs samples made out of different fabrication techniques were investigated and compared. The first set of samples was fabricated using a pressing machine device to fabricate 0.5 inch diameter disk shaped YSZ-Al2O3 samples. The YSZ-Al2O3 powder mixture was made of 0, 1, 2, 3, 4 and …

Structural Health Monitoring With Piezoelectric Wafer Active Sensors—Predictive Modeling And Simulation, Victor Giurgiutiu

Faculty Publications

This paper starts a review of the state of the art in structural health monitoring with piezoelectric wafer active sensors and follows with highlighting the limitations of the current approaches which are predominantly experimental. Subsequently, the paper examines the needs for developing a predictive modeling methodology that would allow to perform extensive parameter studies to determine the sensing method’s sensitivity to damage and insensitivity to confounding factors such as environmental changes, vibrations, and structural manufacturing variability. The thesis is made that such a predictive methodology should be multi-scale and multi-domain, thus encompassing the modeling of structure, sensors, electronics, and power …

Structural Health Monitoring With Piezoelectric Wafer Active Sensors--Predictive Modeling And Simulation, Victor Giurgiutiu

Faculty Publications

This paper starts a review of the state of the art in structural health monitoring with piezoelectric wafer active sensors and follows with highlighting the limitations of the current approaches which are predominantly experimental. Subsequently, the paper examines the needs for developing a predictive modeling methodology that would allow to perform extensive parameter studies to determine the sensing method’s sensitivity to damage and insensitivity to confounding factors such as environmental changes, vibrations, and structural manufacturing variability. The thesis is made that such a predictive methodology should be multi-scale and multi-domain, thus encompassing the modeling of structure, sensors, electronics, and power …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Evaluation Of Biological Cell Properties Using Dynamic Indentation Measurement, Guoxin Cao, Namas Chandra

Department of Engineering Mechanics: Faculty Publications

Viscoelastic mechanical properties of biological cells are commonly measured using atomic force microscope (AFM) dynamic indentation with spherical tips. A semiempirical analysis based on numerical simulation is built to determine the cell mechanical properties. It is shown that the existing analysis cannot reflect the accurate values of cell elastic/dynamic modulus due to the effects of substrate, indenter tip size, and cell size. Among these factors, substrate not only increases the true contact radius but also interferes the indentation stress field, which can cause the overestimation of cell moduli. Typically, the substrate effect is much stronger than the other two influences …

Dynamics Of Fibrillar Precursors Of Shishes As A Function Of Stress, Luigi Balzano, Dario Cavallo, Tim B. Van Erp, Zhe Ma, Jan-Willem Housmans, Lucia Fernandez-Ballester, Gerrit W. M. Peters

Department of Engineering Mechanics: Faculty Publications

Shishes are fibrillar crystallites that can be created by deforming a polymer melt. The formation of shishes takes place when flow is strong enough to stretch molecules. In the early stages, bundles of stretched molecules with pre-crystalline order form metastable precursors whose stability depends on their size and, hence, on the stress level. We find that for a specific isotactic polypropylene, close to the nominal melting point, a stress larger than 0.10 MPa leads to stable fibrillar precursors that are partially crystalline immediately after flow. On the other hand, below 0.10 MPa, the aspect ratio of precursors tends to unity …

Feasibility Study Of Solar Driven Underground Cooling System, Michel E. Shafik

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

In the United States the peak electrical use occurs during the summer. In addition, the building sector consumes a major portion of the annual electrical energy consumption. One of the main energy consuming components in the building sector is the Heating, Ventilation, and Air-Conditioning (HVAC) systems. This research studies the feasibility of implementing a solar driven underground cooling system that could contribute to reducing building cooling loads. The developed system consists of an Earth-to-Air Heat Exchanger (EAHE) coupled with a solar chimney that provides a natural cool draft to the test facility building at the Solar Energy Research Test Facility …

Numerical And Analytical Verification Of A Multiscale Computational Model For Impact Problems In Heterogeneous Viscoelastic Materials With Evolving Damage, Bruno Bachiega Araujo

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Composites are engineered materials that take advantage of the particular properties of each of its two or more constituents. They are designed to be stronger, lighter and to last longer which can lead to the creation of safer protection gear, more fuel efficient transportation methods and more affordable materials, among other examples.

This thesis proposes a numerical and analytical verification of an in-house developed multiscale model for predicting the mechanical behavior of composite materials with various configurations subjected to impact loading. This verification is done by comparing the results obtained with analytical and numerical solutions with the results found when …

Finite Element Analysis Of Cracks In Aging Aircraft Structures With Bonded Composite-Patch Repairs, Linxia Gu, Ananth Ram Mahanth Kasavajhala, Shijia Zhao

Department of Mechanical and Materials Engineering: Faculty Publications

Bonded composite-patch repair has been used to transfer load from cracked structures to the reinforcement such that subsequent crack propagation is reduced. In this study,the mechanical behavior of a single edge v-notch A17075-T6 plate repaired with 1-ply and 4-ply composite patches was investigated through the finite element method. Contour integral method was used to define and evaluate the stress intensity factors at the crack tip. The effect of the adhesive epoxy film, patch material, thickness and ply orientations on the evolution of the stress intensity factor (SIF) of the repaired structure was examined. The results indicated that the SIF of …

Thermal Models Of Railroad Wheels And Bearings, Kevin D. Cole, Constantine M. Tarawneh, Arturo A. Fuentes, B. M. Wilson, L. Navarro

Department of Mechanical and Materials Engineering: Faculty Publications

The rolling surface for railroad wheels can be a heat source that may have an impact on the performance of the wheel bearing. In this study, experimental data from an electrically-heated railroad wheel set is analyzed by constructing thermal models of the wheel set. A steady finite-element model, a steady-analytical model, and a transient lumped-parameter model are discussed. Model parameters are determined from careful comparisons with the experimental data. The lumped-parameter model given here is intended as a simple predictive tool for determining when wheel heating caused by rail operations will have an impact on bearing temperature. The model parameters …

Characterization Of Ni-Rich Nitihf Based High Temperature Shape Memory Alloys, Gurdish S. Ded

University of Kentucky Master's Theses

Among the potential high temperature shape memory alloys, due to its low cost, medium ductility and high work output NiTiHf seems to be the most promising HTSMA for a wide range of applications in the 100-250ºC. A detailed investigation into the shape memory properties and transformation behavior for the Ni-rich HTSMA with the compositions of Ni_45.3Cu₅Ti_29.7Hf₂₀, Ni_50.3Ti_29.7Hf₂₀ and Ni_45.3Pd₅Ti_29.7Hf₂₀ was carried out. It is possible to form Ni-rich precipitates in Ni-rich NiTiHf alloys and tailor the TTs by heat treatments …

Engineering Sport Safety: A Study Of Equestrian Cross Country Eventing, Katherine M. Kahmann

University of Kentucky Master's Theses

The sport of equestrian cross country eventing has seen many serious and even fatal injuries due to rotational horse falls in recent years. The sport originally consisted of horse and rider teams jumping stationary, wood fences. However, in a move towards increasing safety for horses and riders, frangible and deformable safety devices have been emerging in the field. This thesis provides an overview of safety designs that are currently available and those that are on the horizon. Also, a path-finder method of evaluating and developing safety fence designs was outlined and applied to two distinct designs, a hinged gate and …

Uv-Lithographic Patterning Of Micro-Features On A Conical Mold Insert, Justin P. Huber

University of Kentucky Master's Theses

In past studies, several techniques have been employed to create microscopic features on relatively simple surfaces. Of these, lithography-based techniques have proven effective at manufacturing large fields of deterministic microasperities and microcavities on planar and cylindrical substrates. The present study focuses on adapting UV-lithography to a more complex substrate. Machined from stainless steel, a conical mold insert introduces an interesting geometry designed for the injection molding of radial lip seal elastomer. The distinct shape of this mold insert poises unique challenges to a conventional lithography procedure. Spray application is investigated as a feasible means to deposit layers of photoresist on …

Interfacial Thermal Conductivity Using Multiwall Carbon Nanotubes, Carissa Don Russell

University of Kentucky Master's Theses

Shrinking volume, coupled with higher performance, microprocessors and integrated circuits have led to serious heat dissipation issues. In an effort to mitigate the excessive amounts of waste heat and ensure electronic survivability, heat sinks and spreaders are incorporated into heat generating device structures. This inevitability creates a thermal pathway through an interface. Thermal interfaces can possess serious thermal resistances for heat conduction. The introduction of a thermal interface material (TIM) can drastically increase the thermal performance of the component. Exceptional thermal properties of multiwall carbon nanotubes (MWCNTs) have spurred interest in their use as TIMs. MWCNTs inherently grow in vertically-oriented, …

Characterization Of Defects In Metal Sheets Via Infrared Thermography, Marc Anthony Harik

University of Kentucky Master's Theses

Defects in Aluminum, Stainless steel and galvanized steel sheets are studied in reflection mode infrared thermography. The effect of material properties, surface finish, heating intensity, heater emission spectra, pixel size and defect size are studied. Contrast is governed by heat quality, emissivity and defect geometry—which follows a logarithmic trend. The diameter detected via infrared thermography is found to be at least 30% larger than the measured diameter and sub-pixel defects can be detected. The use of gradient and Laplacian of temperature is introduced as a means of increasing defect contrast and mitigating heater variation.

Sustainable Resource Utilization In Manufacturing Of Printed Circuit Board Assembly: Exergy Analysis Of The Process, Subramaniam Saiganesh

University of Kentucky Master's Theses

Engineering for sustainable development requires prudent utilization of resources under economic, environmental and societal constraints. Resource utilization must follow a holistic approach. This brings in a need for comprehensive metrics which are simple, standard and universal. Thermodynamics may offer a metric that focuses on both quality and quantity of energy resources which may carry information to be combined with other metrics. This metric may be a thermodynamic property called exergy or available energy, which provides a better insight into resource use in both energy and non-energy producing systems. This thesis is devoted to a study of the exergy concept in …

Transitional Flow Prediction Of A Compressor Airfoil, Vivek Hariharan

University of Kentucky Master's Theses

The steady flow aerodynamics of a cascade of compressor airfoils is computed using a two-dimensional thin layer Navier-Stokes flow solver. The Dhawan and Narasimha transition model and Mayle‟s transition length model were implemented in this flow solver so that transition from laminar to turbulent flow could be included in the computations. A method to speed up the convergence of the fully turbulent calculations has been introduced. In addition, the effect of turbulence production formulations and including streamline curvature correction in the Spalart-Allmaras turbulence model on the transition calculations is studied. These transitional calculations are correlated with the low and high …

Numerical Modeling Of The Dynamic Response Of A Multi-Bilinear-Spring Support System, Trey D. Gilliam

University of Kentucky Master's Theses

The Alpha Magnetic Spectrometer is an International Space Station Experiment that features a unique nonlinear support system with no previous flight heritage. The experiment consists of multiple straps with piecewise-linear stiffness curves that support a cryogenic magnet in three-dimensional space inside of a vacuum chamber. The stiffness curves for each strap are essentially bilinear and switch between two distinct slopes at a specified displacement. This highly nonlinear support system poses many questions in regards to feasible computational methods of analysis and possible response behavior. This thesis develops a numerical model for a multi-bilinear-spring support system motivated by the Alpha Magnetic …

Investigation And Modeling Of Ice Fracture In Cold Ocean Engineering Applications, Rocky S. Taylor

Link Foundation Ocean Engineering and Instrumentation Fellowship Reports

Ice conditions present a significant challenge in the design of ships and structures for the development of offshore energy resources in cold ocean environments. Many regions throughout the world including Alaska, Canada, Russia, Norway, Kazakhstan and China are developing offshore energy resources in ice-prone environments. The growth and stability of the global economy is closely linked to that of our energy supply, and offshore industrial activity in Northern regions has increased significantly in recent years. One of the most significant engineering challenges when designing structures for ice environments is the estimation of design ice loads. The design load scenario for …