Mechanical Engineering Commons^™

Electromagnetic Field Calculations For Microlens Optical Systems, Jian Wang

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Microlenses are becoming more widely used in modern optical equipment. When the microlens diameter is comparable with the incident electromagnetic illumination wavelength, diffraction effects through the microlens aperture dominate and significantly affect the microlens optical properties leading to differences from that predicted by ordinary geometrical optics theory. In this work, the continuous-profile symmetrical biconvex microlens is selected for investigation. Its optical properties, with both monochromatic plane wave and TEM00 mode Gaussian beam illumination, are studied using the full-field Separation-of-Variables method (SVM) in the oblate spheroidal coordinate system by calculating the electromagnetic field distributions inside of and adjacent to the microlens. …

Engineering Design And Development, David Kennedy

Conference Papers

Combining Industrial and Functional Design methodologies for the development of new products and systems requires a broad understanding of human behaviour and industrial activities. The requirements of international standards, protection of the environment and the ability to make a profit on sales requires a sound attitude and approach to succeed, especially in current economic conditions. This highlights the importance of good business and management strategy that must be dynamic to meet the changing needs of the market. Competitiveness depends largely upon advances in the fields of design and Innovation, cutting edge research and new advances over a broad range of …

A Novel Piezoelectric Device With Dual Functions Of Studying Biological Soft Tissues, Avin A. Jamadagni

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents the design of a novel piezoelectric device with dual functions of studying soft biological tissues. The device consists of a central circular plate and a set of flexural beams. The flexural beams are partially covered with piezoelectric film for integrated transduction. It can function as a force sensor for measuring the mechanical behavior of a tissue sample and a load applier for mimicking physiological loads experienced by the tissue sample in vivo, while the mechanical behavior can be visually observed under a microscope simultaneously. By combining the classic theories in solid mechanics and piezoelectricity, the performance of …

Turbulence Measurement With Coherent Doppler Sonar, Jeremy Dillon

Link Foundation Ocean Engineering and Instrumentation Fellowship Reports

The ocean has been described as Earth's "fi nal frontier" in a vision statement on ocean exploration (National Oceanic and Atmospheric Administration, 2000). The search for new insight is motivated by the fact that our environmental and economic security depends critically on the ocean and the freshwater bodies that drain into it. As the vast majority of the ocean is unknown and unexplored, there is great potential for scientifi c discovery beneath the sea surface (McNutt, 2002). The development of remote and in situ sensors forms a cornerstone of this vision for exploring ocean dynamics at new scales.

Opportunities For Energy Conservation And Improved Comfort From Wind Washing Retrofits In Two-Story Homes - Part Ii, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

Wind washing is a general term referring to diminished thermal control caused by air movement partially or completely bypassing the thermal barrier. The primary focus of this paper relates to a specific type of wind washing where wind can push attic air into the floor cavity between first and second stories of the home through ineffective (or missing) air barriers separating attic space from the floor cavity. A second type of wind washing studied in this project involves insulation batts on knee walls where space between the batts and the wall board allow air movement against the gypsum wall board. …

Opportunities For Energy Conservation And Improved Comfort From Wind Washing Retrofits In Two-Story Homes - Part I, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

Wind washing is a general term referring to diminished thermal control caused by air movement over or through a thermal barrier. The primary focus of this paper is towards a specific type of wind washing where wind can push attic air into the floor cavity between first and second stories of the home through ineffective (or missing) air barriers separating attic space from the floor cavity. A second type of wind washing studied in this project involved insulation batts on knee walls where space between the batts and the wall board allowed air movement against the gypsum wall board. During …

Affiliate Steps Toward Building Energy Star Homes, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

To certify a home as an Energy Star, a builder works with a RESNET certified home energy rater to evaluate the home with respect to criteria required by the Energy Star program. The following steps will help Habitat affiliates navigate the path toward building Energy Star homes.

Cutting Tool Insert Having Internal Microduct For Coolant, William J. Endres

Michigan Tech Patents

A cutting tool insert includes: a body defining a rake face, a flank face, and a cutting edge at an intersection of the rake and flank faces; and a cooling microduct within the body. A portion of the microduct extends along the cutting edge not more than 0.5 millimeter from the rake face, and not more than 0.5 millimeter from the flank face. The microduct has a cross-sectional area of not more than 1.0 square millimeter. The microduct is adapted to permit the flow of a coolant therethrough to transfer heat away from the cutting edge and extend the useful …

System Identification And State Estimation For Intake Manifold Charge Flow Temperature Of A Compression Ignition Diesel Engine, Ryle D. Maxson

Master's Theses - Daytona Beach

Intake manifold charge temperature is a factor used in mean value engine models (MVEMs) for the calculation of intake mass air charge and oxygen flow. More stringent emission requirements have led to increased deployment of more advanced engine combustion models onto production engine controllers. Measurement of the temperature via physical thermocouple sensors mounted to the engine intake manifold is both slow, in comparison to the changing conditions of an engine, and undesirable due to the cost and increased complexity of extra sensors. A state estimation model has been evaluated that imitates the function of the intake manifold temperature sensor reading, …

Pilot Evaluation Of Energy Savings And Persistence From Residential Energy Demand Feedback Devices In A Hot Climate, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

According to past studies, providing instantaneous feedback on household electrical demand has shown the promise to typically reduce energy consumption by 5-10%. This paper briefly reviews past research and describes a two year pilot evaluation of a low cost residential energy feedback system installed in twenty case study homes in Florida. Although not a statistical sample (the participants were self-selected and interested in reducing energy use), the study showed an average 7% reduction in energy use from feedback homes in the second year of monitoring after controlling for weather-related influences. However, a follow-up evaluation done three years later found little …

Developing Intelligent Engineering Collaboration Tools Through The Use Of Design Rationale, Jordan David Ryskamp

Theses and Dissertations

This thesis presents a new method that improves upon the existing approaches to developing collaborative tools. The new method uses automatically inferred and manually recorded design rationale to intelligently filter the information that is shared by a collaborative tool. This represents an improvement upon the existing state of the art in collaborative engineering tools. To demonstrate the viability of the method three collaborative tools were created. The first is a multi-user collaborative design environment tool named SimulPart and built upon the NX CAD package. SimulPart uses the new method to limit the amount of communication required to keep every user …

2010 Fall Engr333 Project Assignment, Matthew K. Heun

ENGR 333

The Fall 2010 ENGR333 project focused on heating and air-conditioning in campus dormitories, which are notoriously leaky and inefficient.

I asked the students “What would it take to retrofit the Bolt-Heyns-Timmer (BHT) dormitory heating and air-conditioning systems in a manner that achieves LEED certification?”

Customer

The customer for this project was Calvin’s VP for finance Henry DeVries.

Exploring Cost-Effective, High Performance Residential Retrofits For Affordable Housing In The Hot Humid Climate, Florida Solar Energy Center, Janet Mcilvaine

FSEC Energy Research Center®

In 2009, a Department of Energy Building America team led by the Florida Solar Energy Center began working with partners to find cost-effective paths for improving the energy performance of existing homes in the hot humid climate. A test-in energy audit and energy use modeling of the partner's proposed renovation package was performed for 41 affordable and middle income foreclosed homes in Florida and Alabama. HERS1 Indices ranged from 92 to 184 with modeled energy savings ranging from 3% to 50% (average of 26%). Analyses and recommendations were discussed with partners to encourage more efficient retrofits, highlight health and safety …

Defect Detection Microscopy, Stuart Craig Rogers

Theses and Dissertations

The automotive industry's search for stronger lighter materials has been hampered in its desire to make greater use of Magnesium alloys by their poor formability below 150°C. One current challenge is to identify the complex structure and deformation mechanisms at work and determine which of these are primary contributors to the nucleation of defects. Orientation Imaging Microscopy has been the most accessible tool for microstructural analysis over the past 15 years. However, using OIM to analyze defect nucleation sites requires prior knowledge of where the defects will occur because once the defects nucleate the majority of microstructural information is destroyed. …

Reducing Whole Body Vibration Levels In Off-Road, Heavy-Duty Vehicles: A Case Study With Computer Modelling, Shaun Mcfadden, Matthieu Morhan, Brian Hurley

Conference Papers

This paper describes a case study involving the dynamic ride performance of a 30-ton, articulated dumper vehicle. The vehicle in question was originally fitted with a front-end, solid axle with leading arm mechanism. After an engineering design program, the vehicle was custom-fitted with a Timoney Independent suspension system. Extensive testing and modelling activities using LMS Virtual.lab Motion® were undertaken to determine the productivity levels of each vehicle. It was demonstrated that the vehicle fitted with a Timoney suspension could achieve a productivity increase of up to 50%. A health analysis is also presented which shows the Timoney Independent suspension system …

Earth Systems Lesson Plan: Size And Forces Of The Solar System, Getaway Special Team 2010

Education and Outreach

No abstract provided.

Physics Lesson Plan: How Far And Fast Does It Travel?, Getaway Special Team 2010

Education and Outreach

No abstract provided.

Elementary And Middle School Science Lesson Plan: Solid, Liquid, Gas, What Is It?, Getaway Special Team 2010

Education and Outreach

No abstract provided.

Evaluation Of Bias Issues Within Regression-Based Inverse Modeling Methods Against Climate And Building Characteristics Using Synthetic Data, Florida Solar Energy Center, Jamie Cummings

FSEC Energy Research Center®

Typically, a model of the energy use of a building is created using the building's characteristics and climate information for its location. However, models of existing homes can be created using monitored energy and climactic data in a process called inverse modeling. Such a technique has potential for those seeking to evaluate the savings a home before and after a retrofit (Meier, Busch, & Conner, 1988).Several programs use an inverse modeling technique to model a home's energy use based on total home energy use, heating and cooling energy use, and indoor/outdoor temperature data from a home (Kissock, Haberl, & Claridge, …

State Space Model Of A Light Weight Flexible Telescope, Chi-Yeh Hsu

Master's Theses

The accuracy of optical telescope in the past was dominated by the construction of the telescope body and the precision of optical surface. This thesis fits into a larger project with a goal of controlling a flexible telescope in order to help a cheaper telescope achieve higher accuracy. In order to understand the internal motion of telescope, the goal of this thesis is to build a state space model of a two-degree-of-freedom telescope using a known star location as feedback. The model presented in this thesis may be used for the telescope simulation and the control design in the future. …