Other Mechanical Engineering Commons^™

Experiment And Simulation Of The Acoustic Signature Of Fatigued-Cracked Gears In A Two-Stage Gearbox, Matthew James Ostiguy

Master's Theses

This thesis focuses on the development of a health monitoring system for gearbox transmissions. This was accomplished by developing and understanding a two-stage gearbox computer model that emulates an actual gearbox test rig. The computer model contains actual gearbox geometry, flexible shafts, bearings, gear contact forces, input motor torque, output brake torque, and realistic gearbox imbalance. The gear contact force of each gear stage and the input bearing translational acceleration were the main outputs compared between a healthy gearbox and damaged gearbox computer model. The damage of focus was a fatigue crack on the input pinion gear. A sideband energy …

Two-Dimensional Scalar Differential Equations For Transversely Varying Thickness Modes In Piezoelectric Plates And Applications In Acoustic Wave Resonator Sensors, Huijing He

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Generalizations are made for three types of well-known and widely used twodimensional scalar differential equations in the literature describing transversely varying thickness modes in piezoelectric plate resonators. They are for singly-rotated quartz plates, doubly-rotated quartz plates, and plates of crystals of class 6mm with the c-axis along the plate thickness, respectively. The purpose of the generalizations is to include the effects of surface mechanical loads such as mass layers or fluids for resonator -based acoustic wave sensor applications. Surface acoustic impedance is introduced to take into account various surface loads in a general manner for time-harmonic motions. Both unelectroded and …

Modular And Cooperative Medical Devices And Related Systems And Methods, Shane M. Farritor, Mark Rentschler, Amy Lehman

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments disclosed herein relate to modular medical devices, including various devices with detachable modular components and various devices with pivotally attached modular components. Additional embodiments relate to procedures in which various of the devices are used cooperatively. Certain embodiments of the medical devices are robotic in vivo devices.

Workspace Analysis Of A Linear Delta Robot: Calculating The Inscribed Radius, Michael Louis Pauly

Graduate Theses - Mechanical Engineering

One of the most important traits of a robotic manipulator is its work envelope, the space in which the robot can position its end effector. Parallel manipulators, while generally faster, are restricted by smaller work envelopes [1]. As such, understanding the parameters defining a physical robot’s work envelope is essential to the optimal design, selection, and use of robotic parallel manipulators. A Linear Delta Robot (LDR) is a type of parallel manipulator in which three prismatic joints move separate arms which connect to a single triangular end plate [2]. In this study, general inverse kinematics were derived for a linear …

Host-Guest Interaction Dictated Selective Adsorption And Fluorescence Quenching Of A Luminescent Lightweight Metal-Organic Framework Toward Liquid Explosives, Dan Liu, Xiaojuan Liu, Yongxin Liu, Yang Yu, Fanglin Chen, Cheng Wang

Faculty Publications

In this article, we report the successful preparation of a Mg-based luminescent MIL-53 metal–organic framework (MOF), namely [Mg2(BDC)2(BPNO)]·2DMF (1) (BDC = 1,4-benzene dicarboxylate, BPNO = 4,4’- dipyridyl-N,N’-dioxide, DMF = N,N-dimethylformamide) in a mixed solvent containing a 2 : 3 volume ratio of DMF and ethanol (EtOH) under solvothermal conditions. Desolvated compound 1a can be used as an absorbent for selective adsorption and separation of liquid explosives, including nitroaromatic (nitrobenzene (NB)) and nitroaliphatic (nitromethane (NM) and nitroethane (NE)) compounds, through single crystal-to-single crystal (SC–SC) transformations. As one of the weakly luminescent MOFs, the luminescence of compound 1a could be quenched by …

Team Nathan Suspension, Frankie J. Wiggins, Alex D. Seitz, Justin P. Bautista

Mechanical Engineering

Nathan Cooper is an 8-year old boy with Spinal Muscular Atrophy (SMA). SMA has affected Nathan’s muscle development and requires him to use the Standing Dani™ mobility device. The Standing Dani is a motorized standing wheelchair, or Wheelstand. Nathan controls and uses it to get around. Though the Standing Dani performs well for most functions, it has some distinct issues. The primary issue that this project addresses is its lack of suspension and the discomfort that Nathan feels as a result. After talking with our client, we developed several specifications generally related to geometry, safety, vehicle dynamics, and reliability. Many …

A Study Of Shock Analysis Using The Finite Element Method Verified With Euler-Bernoulli Beam Theory; Mechanical Effects Due To Pulse Width Variation Of Shock Inputs; And Evaluation Of Shock Response Of A Mixed Flow Fan, David Jonathan Gonzalez Campos

Master's Theses

A Study Of Shock Analysis Using The Finite Element Method Verified With Euler-Bernoulli Beam Theory; Mechanical Effects Due To Pulse Width Variation Of Shock Inputs; And Evaluation Of Shock Response Of A Mixed Flow Fan

David Jonathan González Campos

For many engineers that use finite element analysis or FEA, it is very important to know how to properly model and obtain accurate solutions for complicated loading conditions such as shock loading. Transient acceleration loads, such as shocks, are not as common as static loads. Analyzing these types of problems is less understood, which is the basis for this study. FEA …

Agricultural Industry Advanced Vehicle Technology: Benchmark Study For Reduction In Petroleum Use, Roger M. Hoy, Rodney Rohrer, Adam Liska, Joe D. Luck, Loren Isom, Deepak R. Keshwani

Adam Liska Papers

Diesel use on farms in the United States has remained relatively constant since 1985, decreasing slightly in 2009, which may be attributed to price increases and the economic recession. During this time, the United States’ harvested area also has remained relatively constant at roughly 300 million acres. In 2010, farm diesel use was 5.4% of the total United States diesel use. Crops accounting for an estimated 65% of United States farm diesel use include corn, soybean, wheat, hay, and alfalfa, respectively, based on harvested crop area and a recent analysis of estimated fuel use by crop. Diesel use in these …

Porphyrin Interaction With Dna-Based Carbon Nanotubes And Regeneration For Light Harvesting, Sawyer E. Morgan, Hanyu Zhang, Jong Hyun Choi

The Summer Undergraduate Research Fellowship (SURF) Symposium

Limitations to current solar cells include the high cost of pure silicon and poor current transfer within cells. An emerging alternative is single-walled carbon nanotubes (SWCNTs), which when combined with DNA and porphyrin chromophores can generate a current when absorbing light. We sought to find a chromophore and conditions that would promote bonding to the SWCNTs and improve light harvesting, while being able to regenerate on the film after being damaged. This was experimentally tested by first making SWCNT films on conducting glass slides. These were then functionalized in solutions of chromophore and spectra were measured to determine the bonding …

Development Of Combined Dual-Pump Vibrational And Pure-Rotational Coherent Anti-Stokes Raman Scattering (Dpvcars And Prcars) System, Shenli Yuan, Aman Satija, Robert Lucht

The Summer Undergraduate Research Fellowship (SURF) Symposium

Coherent anti-Stokes Raman scattering (CARS) [1,2] is a spatially-resolved, time-resolved spectroscopic technique for quantitative measurements in reacting flows [3 – 6]. This work demonstrates a combination of N₂/O₂/CO₂ dual-pump vibrational coherent anti-Stokes Raman scattering (DPVCARS) system and two-beam pure-rotational coherent anti-Stokes Raman scattering (PRCARS) system. It is based on the previous development of combined VCARS and PRCARS system which was used to obtain temperature measurements in non-premixed H₂-air flames. The new combined system will be used to measure the temperature profiles and major species concentrations such as N₂/O₂/CO_{2 …}

Increased Span Length For The Mgs Long-Span Guardrail System, Nicholas A. Weiland

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Long-span guardrail systems have been recognized as an effective means of shielding low-fill culverts while minimizing construction efforts and limiting culvert damage and repair. The current MGS long-span design provided the capability to span unsupported lengths up to 25 ft (7.6 m) without the use of nested guardrail. The excellent performance of the MGS long-span system in full-scale crash tests suggested that longer span lengths may be possible with the current design.

A detailed analysis of the MGS long-span guardrail system was performed using the finite element software program LS-DYNA^®. It was shown that the MGS long-span design …

Adaptive Kayak Seating: The Tide Rider 360, Irvin Camacho, Grant Petersen, Audrey Riddle, Andrea Voigt

Mechanical Engineering

The Adaptive Paddling Program at California Polytechnic State University has sponsored the construction of an adaptive kayak seat, the Tide Rider 360, to provide paddlers with disabilities sufficient trunk support while out on the water. In particular, this design focused on providing the least restrictive environment for all users while still providing sufficient lateral, neck, back, and hip support. This seat is intended for use in the quarterly Adaptive Paddling Program to allow people with disabilities to experience the joys of kayaking in the most comfortable and supportive environment possible.

The following report details the background research, design development, manufacturing, …

Adapted Pool Cue, Cole Clark, Daniel Patterson, Michelle Cheung, Dylan Sauer

Mechanical Engineering

Our primary goal was to develop an adaptive device to allow a user with limited upper body mobility to more effectively play a game of pool. Within this goal it was important to design around the concept of a least restrictive environment, in order to provide the user with as close to a standard pool playing experience as possible. The device was designed to specifically meet the needs of John Lee, an Assistive Technology Specialist at Cal Poly's Disability Resource Center. Mr. Lee has muscular dystrophy, which limits his upper and lower body mobility and currently requires his use of …

Science Of Water Table, Tim Haigh, Kris Francis, Nick Schlemmer

Mechanical Engineering

No abstract provided.

Friction Test Machine, Kyle Raymon Schless, Lynda Beatriz Tesillo, Mustapha Nadri

Mechanical Engineering

No abstract provided.

Lightweight Uav Launcher, Ben Miller, Christian Valoria, Corinne Warnock, Jake Coutlee

Mechanical Engineering

This report discusses the design, construction, and testing of a lightweight, portable UAV launcher. There is a current need for a small team of soldiers to launch a US Marine Tier II UAV in a remote location without transport. Research was conducted into existing UAV launcher designs and the pros and cons of each were recorded. This research served as a basis for concept generation during the initial design development stage. It was required that the design weigh less than 110 lbs, occupy a smaller volume than 48" x 24" 18" in its collapsed state, be portable by a single …

Final Design Report Bull Outdoor Products Tailgating/Backyard Barbecue, Kyle Van Allen, David Mei, Nicholas James Marquez

Mechanical Engineering

Bull Outdoor Products, Inc. is a specialty company whose main products are high end barbecues for use in outdoor kitchens. They desire a more portable barbecue stand(s) that can be used for tailgating. This is to be achieved by creating a dual-purpose stand/frame that allows for the barbecue head to be used on a trailer hitch or as rolling stand that can be used without a trailer hitch.

St. Jude Medical - R&D Robot For Sensor Testing, Andrew Chanul Kim, Stanley Logan Laszczyk, Edgar Nava, Nathan Gall

Electrical Engineering

No abstract provided.

Low-Cost Strider For Guatemala, Nicole Catherine Cooper, Gonzalo Hernandez, Jared W. Tower

Mechanical Engineering

The purpose of this project was to create a strider, a type of standing rehabilitation device, for children in developing countries who have trouble walking and supporting their full body weight. The project was initially brought to us by Cal Poly professor Brian Self, who had visited a clinic in San Marcos and determined that there were children there who had difficulties with walking and were a need for a rehabilitation device. The team discussed the problem with Dr. Self, Matt Robinson (a local San Luis Obispo prosthetist), and Cal Poly physics professor Pete Schwartz, all of whom had visited …

Mobile Solar Pv Trainer, Matthew Myers, Matthew Clause, Lawrence Smith

Mechanical Engineering

The aim of the Mobile Solar PV Trainer Project was to design, construct and test a versatile and robust laboratory training rig for the Cal Poly Electrical Engineering department. This project was inspired by the desire of one or more California Polytechnic State University electrical engineering professors to add laboratory components to two established upper division electrical engineering courses in photovoltaic panels and solar power. This report contains a detailed description of the trainer’s desired specifications, our ideation process, a thorough description of the selected trainer design including part drawings, assembly documentation and a bill of materials as well as …