Electro-Mechanical Systems Commons^™

Development Of A Low-Cost, Photovoltaic-Powered, Automated Water Recovery System, David E. Daley

Master's Theses

An existing water filtration system at the Channel Islands Marine & Wildlife Institute (CIMWI) wastes approximately 25 gallons of water per day rinsing out solid waste under light load. To reduce CIMWI’s water and energy consumption, an automated system was designed and built to recover the rinse water and return it to the existing filtration loop. Models for fluid system requirements, basic energy needs, and photo- voltaic energy generation were created to aid in component selection. Basic sensors and electronics were programmed in Python for use with a Raspberry Pi single board computer to collect and process water recovery data …

Performance Of Calcium Chloride- Ammonia Adsorption Refrigeration System, Michael John

Tanzania Journal of Engineering and Technology (TJET)

An experimental study on the performance of calcium chloride-ammonia adsorption system is described. A single bed water cooled condenser adsorption refrigerator prototype, which utilises calcium chloride-ammonia pair has been developed and tested in the laboratory. Experiments have been conducted for desorption temperatures of 100 °C with desorption time varying from 1 to 4 hours. An electric tape heater and a timer were used to perform the experiments. The adsorption temperature profile, adsorption rate and prototype performance have been analysed and discussed. The tested heating and desorption temperature of 100 °C and heating and desorption time of 1 to 4 hours …

Assessment Of The Impacts Of Climate Variability On Hydropower Generation: A Case Study Of The New Pangani Falls, Tanzania, Dativa Byarufu

Tanzania Journal of Engineering and Technology (TJET)

Climate change poses potential impacts on hydropower generation either positively by increasing or negatively by decreasing river flow. This study assessed the impacts of climate variability on hydropower with a focus on the New Pangani Falls in Tanzania. Rainfall and temperature time series data from 1980-2014 were analyzed in relation to river discharge and associated impacts to hydropower generation. The Man-Kendall test was used to detect trend in both annual and seasonal time series. The results showed a negative trend in annual rainfall with Z= -2.41 at α = 0.05 and the slope Q = -0.964. Seasonal trend analysis showed …

Socio-Technical Perspective For Electronic Tax Information System In Tanzania, Lucas Ngowi, Ellen Kalinga

Tanzania Journal of Engineering and Technology (TJET)

Socio-technical systems theory has rarely been used by system architects in setting up computing systems. However, the role of socio-technical concepts in computing, which is becoming social in nature, has made the concepts more relevant and commercial. Tax information systems are examples of such systems because they are influenced by external variables such as the political environment, technological trends, and social environment, introducing complexity in their deployment and determining the type of e-services and their delivery to a diverse group of people. It was observed that in Tanzania there is resistance, reluctance and minimal use of electronic tax system because …

An Economical Method For Securely Disintegrating Solid-State Drives Using Blenders, Brandon J. Hopkins Phd, Kevin A. Riggle

Journal of Digital Forensics, Security and Law

Pulverizing solid-state drives (SSDs) down to particles no larger than 2 mm is required by the United States National Security Agency (NSA) to ensure the highest level of data security, but commercial disintegrators that achieve this standard are large, heavy, costly, and often difficult to access globally. Here, we present a portable, inexpensive, and accessible method of pulverizing SSDs using a household blender and other readily available materials. We verify this approach by pulverizing SSDs with a variety of household blenders for fixed periods of time and sieve the resulting powder to ensure appropriate particle size. Among the 6 household …

Development Of Novel Battery Materials For Lithium-Ion Batteries And Beyond, Jiyu Cai

Graduate Theses and Dissertations

As fossil fuels are depleting and causing environmental issues, it becomes imperative to widely implement renewable energies (e.g., solar and wind power). In this context, electrical energy storage (EES) systems are essential to accommodate the intermittent supply and uneven distribution of renewable energies. To this end, high-energy-density EES devices are highly demanded, such as rechargeable batteries. This dissertation presents my efforts in developing novel battery materials for lithium-ion batteries (LIBs), sodium-ion batteries (SIBs), and solidstate lithium batteries (SSLBs). These efforts include electrochemical evaluations of battery materials, surface modifications of electrodes via atomic layer deposition (ALD), and advanced characterizations of batteries …

High Temperature Degradation In Gan-Based Hall Effect Sensors, Alexis Anne Krone

Graduate Theses and Dissertations

This research focuses on understanding the effects of accelerated aging through temperature and environment on novel gallium nitride-based Hall effect magnetic field sensors and determining device reliability under electric vehicle operating conditions. The device reliability was modeled using accelerated aging for the temperatures of 200 °C, 350 °C, 450 °C, and 600 °C under various time steps unique to each temperature and either air, which is identical to operating circumstances, or argon, which would model the hermetic packaging environment. Using a high temperature furnace and oven, devices underwent high temperature storage tests at a chosen temperature and time step. Afterwards, …

Problem Solving Methods For Synthesis Of Physical Principles Of Mechatronic Module Operations In Intelligent Robotic Systems, Nazarov Khayriddin Nuritdinovich

Chemical Technology, Control and Management

The scientific paper investigates the methods for solving problems of synthesis of physical principles of operation of mechatronic modules of intelligent robotic systems are considered.

In addition, it deals with the specifics of the process of synthesis of the physical principles of the operation of mechatronic modules using predicate models, list models and information matrices of physical and technical effects.

It shows the interpretation of the components of the model of the system for the synthesis of the physical principles of operation of mechatronic modules of intelligent robotic systems and automatic control and the features of the synthesis algorithm for …

Autonomous Navigation Of The Surface Autonomous Vehicle For Emergency Rescue (Saver), Andrew Skow

ENGS 88 Honors Thesis (AB Students)

Once dropped into the ocean, SAVER will autonomously navigate towards the Advanced Next-Generation Emergency Locator beacon, worn by every NASA astronaut, that emits a 121.5 MHz distress signal. Using a rotating directional loop antenna SAVER is able to detect and identify the direction of the distress beacon and navigate itself towards the signal source. The autonomous navigation system is dependent on several electrical, and mechanical systems to function properly and presents a novel systems engineering problem. Given testing limitations, NASA requires that SAVER is designed to operate indoors and with an umbilical power supply. The radio direction finding (RDF) system …

Cnc Feed Drive Control, Ryan J. Funchess, Caleb P. O'Gorman, Nick J. Desimone, Juan M. Majano, Samuel K. Wong

Mechanical Engineering

This document serves as the Final Design Report (FDR) for a senior project developed by our team: four senior Mechanical Engineering students and one computer engineering student at California Polytechnic State University, San Luis Obispo (Cal Poly). While the project was completed for, and sponsored by, Professor Simon Xing of Cal Poly, the remainder of the university’s controls professors will be indirectly benefited from this project. Our goal was to design and implement a functional CNC Feed Drive to be used for educational demonstrations and data collection. This document discusses our early product research and benchmark goals, which established constraints …

Bull Outdoor Products - Electric Grill, Sofie M. Groberman, Makai J. Baker, James T. Andrews

Mechanical Engineering

Our senior design project team designed, assembled, and tested an outdoor electric grill. The sponsor for our project is Bull Outdoor Products, a high-end outdoor kitchen set, pizza oven, and grill company. We met with our sponsor to discuss project expectations and important product characteristics. We also researched the barbecue market and its customers to determine what grill characteristics are the most important. We learned which engineering specifications needed to be tested and outlined what our goals and overall objectives for this project are. With our background research and overall objectives in mind, we came up with different solutions through …

Modeling And Control Of A Vertical Hopping Robot, Bradley Y. Kwan

Master's Theses

Single degree-of-freedom hopping robots are typically modeled as spring loaded inverted pendulums (SLIPs). This simplified model, however, does not consider the overall leg geometry, consequently making it difficult to investigate the optimized inertial distribution of the leg for agile locomotion. To address this issue, the first part of this thesis establishes an accurate mathematical model of a DC-motor-driven, two-link hopping robot where the motors are modeled as torque sources. The equations of motion for the two distinct phases of locomotion (stance and flight) are derived using the Lagrangian approach for holonomic systems. A Simulink/Stateflow model is developed to numerically simulate …

Adjustable Height Pedestal Grinder Stand, Josef Zagorski, Zachary Wedel, Michael Sitar, Daniel Zevenbergen

Mechanical Engineering

Pedestal grinders are one of the most common machines found in machine shops today. The current industry standard for mounting a grinder is on a fixed single pillar, cast iron pedestal. A fixed pedestal allows for no vertical adjustment for shop users of different sizes and is a safety hazard. This report further defines this problem and proposes an iterative design process to meet the needs and wants of the customer. The adjustable-height pedestal grinder stand Senior Project team used this problem and design process to successfully complete the project within the allotted time. The first major deliverable and milestone …

Tensile Testing Environmental Chamber – Structural, Michael Ingel, Erik Soldenwagner, Austin Marshall, Lauren Schirle

Mechanical Engineering

Environmental chambers for tensile testing machines are used to study how a multitude of materials behave in extreme temperatures. These chambers provide the necessary information to innovate cutting edge technology for materials in fields such as aerospace. These chambers are often heavy and expensive requiring a significant amount of time and money just in the installation process alone. This report will serve to outline and define the design and fabrication of an environmental chamber, conducted by a team of four senior mechanical engineering students at California Polytechnic State University, San Luis Obispo. The goals of the project include a low-weight …

Saver (Surface Autonomous Vehicle For Emergency Rescue), Tyler Jorgensen, Ethan Miller, Josephine Isaacson, Joshua Hoye

Mechanical Engineering

This document serves to introduce the design team and their competition challenge, as well as to detail the results of the project. The original design challenge was the NASA Micro-g NExT’s SAVER (Surface Autonomous Vehicle for Emergency Rescue) competition; we were tasked with developing a self-driving water vehicle capable of delivering supplies to Orion astronauts separated from the rest of their crew in the case of a maritime emergency. However, we were not selected to go forward in this competition and thus we decided to scale down the size of the SAVER device to shift the focus of the project …

Inverted Fluorescence Microscope, Matthew B. Pfeiffer, Spencer George Hann, Thomas James Eggenberger, Trevor Lee Blythe

Mechanical Engineering

Team F13 is composed of Trevor Blythe, Spencer Hann, Matthew Pfeiffer, and Thomas Eggenberger. We are all majoring in mechanical engineering and in our final year of study here at Cal Poly San Luis Obispo. This project is a continuation of a 2019-2020 senior project. The previous team designed and built a functioning inverted fluorescence microscope (IFM) from scratch. This device was created as a lab tool for undergraduate students to be able to perform experiments on microfluidic devices constructed in Cal Poly’s Microfabrication Laboratory. Although substantially functional, several design constraints had not yet been met. Our team has improved …

3-D Positioning System For Trackable Adjustments Of Papillary Muscles, Ryan Michael Winters, Micaela Andrea Bataclan, Christine Do, Giselle Morales

Biomedical Engineering

Redacted.

Consumer-Ready Insulated Solar Electric Cooker, Simon Ford, Sachin Gokhale, Brendan Lynn, Richard Nguyen

Mechanical Engineering

An insulated solar electric cooker, or ISEC, converts solar energy into electricity to cook food, boil water, provide heat or even help charge batteries. In this project, the focus is an ISEC with a phase change material (PCM) that helps store heat when the solar energy input is minimal, such as after the sun has set. Although a successful ISEC already exists that utilizes PCM, this product can be improved in many ways. The specific revisions investigated in this report are the improvement of the thermal efficiency with the implementation of a vacuum-sealed outer pot, the reduction of the overall …

Feasibility Study Of Radio Frequency Microelectromechanical Filters For Space Operation, Karanvir Singh

Theses and Dissertations

Piezoelectric contour mode resonator technology has the unique advantage of combining low motional resistance with the ability to define multiple frequencies on the same substrate. Contour mode resonators can be mechanically coupled together to form robust band-pass filters for the next generation of GPS satellites with extreme size reduction compared to electrically coupled filters. Piezoelectric zinc oxide (ZnO) contour mode resonators have the potential for monolithic integration with current ZnO transistor further reducing size, power consumption, and cost of filter modules. Barium strontium titanate (BST) contour mode resonators have incredible frequency tunability due to the fundamental nature of the thin …

Magnetic Gradient-Based Magnetic Tweezer System For 3d And Swarm Control Of Microswimmer, Xiao Zhang

Mechanical Engineering Research Theses and Dissertations

Microscale manipulation has very promising potential in medical applications such as drug delivery, minimal and invasion surgery. Contactless control is preferable as remote manipulation is necessary for in vivo applications. Among different control methods, magnetic power source is more suitable and robust for the applications mentioned above. Presented here is a magnetic tweezer system, which manipulates microscale magnetic particles using magnetic forces created by magnetic field gradient. The proposed system has three advantages: First, force applied by the magnetic tweezer system does not contact with the target object and can be generated in different directions. Second, the magnetic tweezer system …