Acoustics, Dynamics, and Controls Commons^™

Static Balancing Of The Cal Poly Wind Turbine Rotor, Derek Simon

Master's Theses

The balancing of a wind turbine rotor is a crucial step affecting the machine’s performance, reliability, and safety, as it directly impacts the dynamic loads on the entire structure.

A rotor can be balanced either statically or dynamically. A method of rotor balancing was developed that achieves both the simplicity of static balancing and the accuracy of dynamic balancing. This method is best suited, but not limited, to hollow composite blades of any size. The method starts by quantifying the mass and center of gravity of each blade. A dynamic calculation is performed to determine the theoretical shaking force on …

Effects Of Acoustic Environments On Speech Comprehension By Native-English-Speaking Listeners, Zhao Peng, Lily M. Wang, Siu Kit Lau

Durham School of Architectural Engineering and Construction: Faculty Publications

This study investigates the effects of acoustic conditions on speech comprehension, rather than speech intelligibility as often reported in existing literature. Sets of 15-minute-long listening comprehension tests were developed based on the format of the Test of English for International Communication (TOEIC). Each test set includes four types of tasks: matching aural phrases to photographs, selecting appropriate responses to aural questions, and answering questions after listening to conversations (between two talkers) and talks (single talker). Within the Nebraska acoustics test chamber, native-English-speaking participants are asked to perform these tests under 15 acoustic conditions, from combinations of three background noise levels …

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …

Vibration Health Monitoring Of Gears, Markus Josef Scherer

Master's Theses

Monitoring the health of vibrating gears is important to ensure proper operation especially in potentially life-threatening structures, such as helicopters, nuclear power plants, and uninterruptible power supply transitions in hospitals. The most common monitoring technique is casing mounted accelerometers to measure vibration. In contrast, during the last few years acoustic monitoring techniques have also provided a few diagnostic methods for gear failure. Current diagnostic methods to indicate improper gear behavior use either existing vibration data, recorded from defective gear systems, or modern dynamic models predicting gear failure behavior.

This thesis uses dynamic models to indicate, predict, and diagnose healthy and …

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Supermileage Chassis Dynamometer, Jose Garcia, Steve Janning, Timothy Lui, Kyla Purvis

Mechanical Engineering

This report describes the final design and analysis of a hydraulic chassis dynamometer as a testing tool for California Polytechnic State University, San Luis Obispo Supermileage Vehicle Team (CPSMV). Literature review was conducted to understand the various types of chassis dynamometers on the market as of the year 2011. After rigorous research, it was determined that a hydraulic system was the best system for a chassis dynamometer in terms of functionality, performance, and cost. Critical study of hydraulics, dynamometers, and data acquisition systems (DAQ) was followed by a complete design of a hydraulic system. The chassis dynamometer proposed in this …

California Olive Ranch Hedger, Tyler Enos, Seth Abbott, David Gamba

Mechanical Engineering

The purpose of this project is to evaluate the problems of the current KCI (Kingsburg Cultivator Incorporated) olive tree hedger in use at California Olive Ranch (COR) in Artois, CA, and then correct these problems which should yield a better performing, more efficient, and reliable machine. These problems include: the hydraulic oil temperature getting too high, the saw blades not having enough horsepower, and poor cutting performance due to operator error as well as terrain variations.

A Model Predictive Control Approach To Roll Stability Of A Scaled Crash Avoidance Vehicle, Nikola John Linn Noxon

Master's Theses

In this paper, a roll stability controller (RSC) is presented based on an eight degree of freedom dynamic vehicle model. The controller is designed for and tested on a scaled vehicle performing obstacle avoidance maneuvers on a populated test track. A rapidly-exploring random tree (RRT) algorithm is used for the vehicle to execute a trajectory around an obstacle, and examines the geographic, non-homonymic, and dynamic constraints to maneuver around the obstacle. A model predictive controller (MPC) uses information about the vehicle state and, based on a weighted performance measure, generates an optimal trajectory around the obstacle. The RSC uses the …

An Investigation Of Damage Arrestment Devices On Carbon Fiber Sandwich Specimens Under Dynamic Loading, Gabriel Sabino Sanchez

Master's Theses

This research studies the effects of a damage arrestment device embedded between a carbon fiber facesheet and foam core to find whether there is an increase in the structural integrity of the sandwich composites. Experimental and theoretical finite element analyses are implemented for two different composite sandwich geometries; plates and beams. Each structure consisted of the same loading criteria and was restricted to the same vibration fixture during the experiment. An accelerometer was placed on the composite plate to record the amplitude and the natural frequencies of the composite structure. Each composite specimen is then fixed to the surface of …

Resonance Frequencies Of A Spherical Aluminum Shell Subject To Static Internal Pressure, Andrew A. Piacsek, Sami Abdul-Wahid, Robert Taylor

All Faculty Scholarship for the College of the Sciences

Measurements of the vibrational response of a spherical aluminum shell subject to changes in the interior pressure clearly demonstrate that resonance frequencies shift higher as the pressure is increased. The frequency shift appears to be smaller for longitudinal modes than for bending wave modes. The magnitude of frequency shift is comparable to analytical predictions made for thin cylindrical shells. Changes in the amplitudes of resonance peaks are also observed. A possible application of this result is a method for noninvasively monitoring pressure changes inside sealed containers, including intracranial pressure in humans.

Acoustic Emission Detection Of Metals And Alloys During Machining Operations, Jameson K. Nelson

Purdue Polytechnic Masters Theses

Nelson, Jameson K. M.S., Purdue University, May 2012. Acoustic Emission Detection of Metals and Alloys During Machining Operations. Major Professor: Rodney G. Handy.

Practical correlation between material deformation attributes and theoretical concepts of machining has proven difficult to attain. The purpose of this study was to further explore trends and relationships using acoustic emission detection of materials undergoing single-point lathe turning machine processes. The majority of machining experiments that incorporate acoustic emissions focuses on tool degradation for the purposes of optimizing consumables required to manufacture mechanical devices. Experiments were implemented varying recording location, mechanical barrier condition, and machine parameters. The …

A Novel Ultrasonic Method To Quantify Bolt Tension, Jairo Andres Martinez Garcia

USF Tampa Graduate Theses and Dissertations

The threaded fasteners are one of the most versatile methods for assembly of structural components. For example, in bridges large bolts are used to fix base columns and small bolts are used to support access ladders. Naturally not all bolts are critical for the operation of the structure. Fasteners loaded with small forces and present in large quantities do not receive the same treatment as the critical bolts. Typical maintenance operations such tension measurements, internal stress checking or monitoring of crack development are not practical due to cost and time constrains. Although failure of a single non-critical fastener is not …

Acoustic Testing And Modeling: An Advanced Undergraduate Laboratory, Daniel A. Russell, Daniel O. Ludwigsen

Physics Publications

This paper describes an advanced laboratory course in acoustics, specifically targeted for students with an interest in engineering applications at a school with a strongly integrated industrial co-op program. The laboratory course is developed around a three-pronged approach to problem solving that combines and integrates theoretical models, computational models, and experimental data. The course is structured around modules that begin with fundamental concepts and build laboratory skills and expand the knowledge base toward a final project. Students keep a detailed laboratory notebook, write research papers in teams, and must pass laboratory certification exams. This paper describes the course layout and …

A Review Of Some Subtleties Of Practical Relevance, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper reviews some subtleties in time-delay systems of neutral type that are believed to be of particular relevance in practice. Both traditional formulation and the coupled differential-difference equation formulation are used. The discontinuity of the spectrum as a function of delays is discussed. Conditions to guarantee stability under small parameter variations are given. A number of subjects that have been discussed in the literature, often using different methods, are reviewed to illustrate some fundamental concepts. These include systems with small delays, the sensitivity of Smith predictor to small delay mismatch, and the discrete implementation of distributed-delay feedback control. The …

Hydraulic Test Bench Circuit Construction, Testing, And Analysis, Shane Michelson, Mitch Mueller, Brett Schurman

The Journal of Undergraduate Research

Hydraulic power control systems are a common and important part of mechanical and agricultural systems. In hydraulic power system design, power, pressure, flow rates, and mechanism of circuitry are all important factors when analyzing any hydraulic system. Pumps, electric motors, reservoirs, working fluid properties, hydraulic circuitry, and a large variety of valves make up a functional hydraulic system. Applications for hydraulic systems vary widely from automotive, agricultural, mechanical etc. It is the engineers’ job to design a hydraulic system that will be functional, efficient, and safe.

Simulation Of Whistle Noise Using Computational Fluid Dynamics And Acoustic Finite Element Simulation, Jiawei Liu

Theses and Dissertations--Mechanical and Aerospace Engineering

The prediction of sound generated from fluid flow has always been a difficult subject due to the nonlinearities in the governing equations. However, flow noise can now be simulated with the help of modern computation techniques and super computers. The research presented in this thesis uses the computational fluid dynamics (CFD) and the acoustic finite element method (FEM) in order to simulate the whistle noise caused by vortex shedding. The acoustic results were compared to both analytical solutions and experimental results to better understand the effects of turbulence models, fluid compressibility, and wall boundary meshes on the acoustic frequency response. …

Root Locus Techniques With Nonlinear Gain Parameterization, Brandon Wellman

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents rules that characterize the root locus for polynomials that are nonlinear in the root-locus parameter k. Classical root locus applies to polynomials that are affine in k. In contrast, this thesis considers polynomials that are quadratic or cubic in k. In particular, we focus on constructing the root locus for linear feedback control systems, where the closed-loop denominator polynomial is quadratic or cubic in k. First, we present quadratic root-locus rules for a controller class that yields a closed-loop denominator polynomial that is quadratic in k. Next, we develop cubic root-locus rules …

Aerodynamics And Control Of A Deployable Wing Uav For Autonomous Flight, Michael Thamann

Theses and Dissertations--Mechanical and Aerospace Engineering

UAV development and usage has increased dramatically in the last 15 years. In this time frame the potential has been realized for deployable UAVs to the extent that a new class of UAV was defined for these systems. Inflatable wing UAVs provide a unique solution for deployable UAVs because they are highly packable (some collapsing to 5-10% of their deployed volume) and have the potential for the incorporation of wing shaping. In this thesis, aerodynamic coefficients and aileron effectiveness were derived from the equations of motion of aircraft as necessary parameters for autonomous flight. A wind tunnel experiment was performed …

Dolphin Sound Production And Distribution On The West Florida Shelf, Peter Simard

USF Tampa Graduate Theses and Dissertations

This dissertation is an investigation of dolphin sound production and distribution off west central Florida. Although a wealth of information exists on the production of common sounds (whistles, echolocation) made by captive, trained dolphins, far less is known about free-ranging dolphin sound production and of unusual sounds. In addition, while inshore dolphin populations or communities are the subjects of research projects in many locations, dolphins in offshore waters are less commonly studied. The objectives of this dissertation were to contribute information on free-ranging dolphin sounds and continental shelf dolphin distribution.

While echolocation has been rigorously studied in captive, trained dolphins, …

Characterizing The Acoustic Properties Of The Jet Lab At The National Center For Physical Acoustics, Joshua Anderson Lieblong

Electronic Theses and Dissertations

Aerodynamic noise has been a problem since the first use of the jet engine for military aircraft in World War II. For further uses of the jet engine to be possible, problems due to jet noise must be researched and addressed. Anechoic chambers were proposed as a testing facility for research in aerodynamic noise because of their supposed free-field characteristics. The international standard ISO 3745-1977 was introduced to determine whether the facilities could be considered anechoic, semi-anechoic, or neither. An experiment was designed to determine at what frequencies the National Center for Physical Acoustics' Jet Lab Facility is non-anechoic, semi-anechoic, …