Acoustics, Dynamics, and Controls Commons^™

Assessing And Mitigating Airborne Noise From Power Generation Equipment, Limin Zhou

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation examines the assessment and mitigation of airborne noise from power generation equipment.

The first half of the dissertation investigates the diagnosis and treatment of combustion oscillations in boilers. Sound is produced by the flame and is reflected downstream from the combustion chamber. The reflected sound waves perturb the mixture flow or equivalence ratio increasing the heat release pulsations and the accompanying sound produced by the flame. A feedback loop model for determining the likelihood of and diagnosing combustion oscillations was reviewed, enhanced, and then validated. The current work applies the feedback loop stability model to two boilers, which …

Decentralized Adaptive Control For Uncertain Linear Systems: Techniques With Local Full-State Feedback Or Local Relative-Degree-One Output Feedback, James D. Polston

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents decentralized model reference adaptive control techniques for systems with full-state feedback and systems with output feedback. The controllers are strictly decentralized, that is, each local controller uses feedback from only local subsystems and no information is shared between local controllers.

The full-state feedback decentralized controller is effective for multi-input systems, where the dynamics matrix and control-input matrix are unknown. The decentralized controller achieves asymptotic stabilization and command following in the presence of sinusoidal disturbances with known spectrum. We present a construction technique of the reference-model dynamics such that the decentralized controller is effective for systems with arbitrarily …

Advanced Studies On Transfer Impedance With Application To After-Treatment Devices And Micro-Perforated Panel Absorbers, Xin Hua

Theses and Dissertations--Mechanical and Aerospace Engineering

This work is primarily comprised of five self-contained papers. Three papers are applications oriented. A common element in the first three papers is that micro-perforated panels (MPP), the permeable membranes in diesel particulate filters, and a source impedance are all modeled as a transfer impedance. The first paper deals with enhancing the performance of micro-perforated panels by partitioning the backing cavity. Several different backing schemes are considered which enhance the performance without increasing the total volume of the MPP and backing. In the second paper, a finite element modeling approach is used to model diesel particulate filters below and above …

Experimental Investigation To Inform Optimal Configurations For Dynamic Near-Field Passive Uhf Rfid Systems, Donnie E. Proffitt Ii

Theses and Dissertations--Mechanical and Aerospace Engineering

RFID has been characterized as a “disruptive technology” that has the potential to revolutionize numerous key sectors. A key advantage of passive RFID applications is the ability to wirelessly transmit automatic identification and related information using very little power. This paper presents an experimental investigation to inform the optimal configuration for programming passive ultra-high frequency (UHF) RFID media in dynamic applications. Dynamic programming solutions must be designed around the tag’s functionality, the physical programming configuration and environment. In this investigation, we present a methodology to determine an optimal configuration to maximize the systems programming efficiency for dynamic applications.

Binaural Room Impulse Response Database Acquired From A Variable Acoustics Classroom, Zhao Peng, Siu Kit Lau, Lily M. Wang, Sean Browne, Kenneth P. Roy

Durham School of Architectural Engineering and Construction: Faculty Publications

Room measurements were conducted in a variable acoustics classroom mockup space (epod) at Armstrong World Industries in Lancaster, Pennsylvania, USA. Binaural room impulse responses were measured in the epod using a head and torso simulator. Five reverberation time (RT) scenarios were achieved with various combinations of absorptive wall panels and acoustical ceiling tile. These provided a range of mid-frequency RTs from 0.4 to 1.1 seconds. Three of the five RT scenarios were achieved using two different material configurations to also consider material location effects. For each of the eight material configurations, two student-teacher orientations were tested. One orientation had all …

Structure Borne Noise Analysis Using Helmholtz Equation Least Squares Based Forced Vibro Acoustic Components, Logesh Kumar Natarajan

Wayne State University Dissertations

This dissertation presents a structure-borne noise analysis technology that is focused on providing a cost-effective noise reduction strategy. Structure-borne sound is generated or transmitted through structural vibration; however, only a small portion of the vibration can effectively produce sound and radiate it to the far-field. Therefore, cost-effective noise reduction is reliant on identifying and suppressing the critical vibration components that are directly responsible for an undesired sound. However, current technologies cannot successfully identify these critical vibration components from the point of view of direct contribution to sound radiation and hence cannot guarantee the best cost-effective noise reduction.

The technology developed …

Automated Extraction And Classification Of Time-Frequency Contours In Humpback Vocalizations, Hui Ou, Whitlow W.L. Au, Lisa M. Zurk, Marc O. Lammers

Electrical and Computer Engineering Faculty Publications and Presentations

A time-frequency contour extraction and classification algorithm was created to analyze humpback whale vocalizations. The algorithm automatically extracted contours of whale vocalization units by searching for gray-level discontinuities in the spectrogram images. The unit-to-unit similarity was quantified by cross-correlating the contour lines. A library of distinctive humpback units was then generated by applying an unsupervised, cluster-based learning algorithm. The purpose of this study was to provide a fast and automated feature selection tool to describe the vocal signatures of animal groups. This approach could benefit a variety of applications such as species description, identification, and evolution of song structures. The …

Project Haiti 2012: Providing An Experiential Learning Experience Through The Design And Delivery Of A Water Purifier In Haiti, Yung Wong, Johnathon Camp, Shavin Pinto, Kyle Fennesy, Marc Compere, Yan Tang

Publications

In this paper, we share our experiences and lessons learned from Project Haiti 2012, a project to design and install a water purification system serving 20,000 people per day in the largest tent city in Haiti. Project Haiti 2012 was the third and largest system we have built for Haitians and represents a huge success for all participants and stakeholders. This paper discusses the unique experiential learning opportunity involved in the design and delivery of the water purifier in a foreign developing country. Multiple positive educational, social, and economic outcomes were achieved including students applying knowledge gained from coursework towards …

Implementation Of Magnetic Resonance Elastography For The Investigation Of Traumatic Brain Injuries, Thomas Boulet

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Magnetic resonance elastography (MRE) is a potentially transformative imaging modality allowing local and non-invasive measurement of biological tissue mechanical properties. It uses a specific phase contrast MR pulse sequence to measure induced vibratory motion in soft material, from which material properties can be estimated. Compared to other imaging techniques, MRE is able to detect tissue pathology at early stages by quantifying the changes in tissue stiffness associated with diseases. In an effort to develop the technique and improve its capabilities, two inversion algorithms were written to evaluate viscoelastic properties from the measured displacements fields. The first one was based on …

Hepa Filter Evaluation Furnace Control Unit, Matt Gainer, Marc Goupil, Andrew Woolrich

Mechanical Engineering

No abstract provided.

Optimal Reduction Of Electrical Energy Consumption By Supply Air Ac Motors, Keyhan Rafiee

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Nebraska Center for Energy Sciences Research (NCER) at the University of Nebraska-Lincoln (UNL) strives to be energy efficient through Green Energy. Of course, in meeting some of the requirements for different types of Leadership in Energy and Environmental Design (LEED) certification, certain minimum levels of energy efficiency practices must be met. One such level of energy efficiency, in particular, is reduction in the consumption of electrical energy in buildings. This thesis is a study of methods of reducing the consumption of electrical energy (measured in kW of electrical power) in the UNL Jorgensen Hall (JH) air handling unit 2 …

Efficient Characterization Of Structural Dynamic Responses Under Uncertainties: From Order-Reduced Simulation To Data-Driven Emulation, Zeping Xia

Master's Theses

The efficiency of sampling remains as one of the major challenges for uncertainty analysis in structural dynamics. In the context of numerical experiments, this difficulty primarily lies in the fact that every single run of a numerical model, which usually is of large scale in modern engineering practice, would be expensive in terms of CPU times and memories. Nonetheless, understanding and predicting dynamic characteristics of structural systems with uncertainties is important for structural design, assessment and control. In order to develop fast and economical sampling techniques for characterizing structural dynamics, we explored two categories of methods from two opposite direction: …

Static Balancing Of The Cal Poly Wind Turbine Rotor, Derek Simon

Master's Theses

The balancing of a wind turbine rotor is a crucial step affecting the machine’s performance, reliability, and safety, as it directly impacts the dynamic loads on the entire structure.

A rotor can be balanced either statically or dynamically. A method of rotor balancing was developed that achieves both the simplicity of static balancing and the accuracy of dynamic balancing. This method is best suited, but not limited, to hollow composite blades of any size. The method starts by quantifying the mass and center of gravity of each blade. A dynamic calculation is performed to determine the theoretical shaking force on …

Effects Of Acoustic Environments On Speech Comprehension By Native-English-Speaking Listeners, Zhao Peng, Lily M. Wang, Siu Kit Lau

Durham School of Architectural Engineering and Construction: Faculty Publications

This study investigates the effects of acoustic conditions on speech comprehension, rather than speech intelligibility as often reported in existing literature. Sets of 15-minute-long listening comprehension tests were developed based on the format of the Test of English for International Communication (TOEIC). Each test set includes four types of tasks: matching aural phrases to photographs, selecting appropriate responses to aural questions, and answering questions after listening to conversations (between two talkers) and talks (single talker). Within the Nebraska acoustics test chamber, native-English-speaking participants are asked to perform these tests under 15 acoustic conditions, from combinations of three background noise levels …

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …

Vibration Health Monitoring Of Gears, Markus Josef Scherer

Master's Theses

Monitoring the health of vibrating gears is important to ensure proper operation especially in potentially life-threatening structures, such as helicopters, nuclear power plants, and uninterruptible power supply transitions in hospitals. The most common monitoring technique is casing mounted accelerometers to measure vibration. In contrast, during the last few years acoustic monitoring techniques have also provided a few diagnostic methods for gear failure. Current diagnostic methods to indicate improper gear behavior use either existing vibration data, recorded from defective gear systems, or modern dynamic models predicting gear failure behavior.

This thesis uses dynamic models to indicate, predict, and diagnose healthy and …

Human Powered Helicopter: Rotor Structure, Joseph Ram, Juan Carlos Olvera

Mechanical Engineering

The following report encompasses the Human Powered Helicopter Rotor Team’s conceptual models and ideas based on research and modeling analysis. The following gives an overview of material researched, concept generation, analyzation, manufacturing, and testing for a rotor structure to be installed in a Human Powered Helicopter.

Supermileage Chassis Dynamometer, Jose Garcia, Steve Janning, Timothy Lui, Kyla Purvis

Mechanical Engineering

This report describes the final design and analysis of a hydraulic chassis dynamometer as a testing tool for California Polytechnic State University, San Luis Obispo Supermileage Vehicle Team (CPSMV). Literature review was conducted to understand the various types of chassis dynamometers on the market as of the year 2011. After rigorous research, it was determined that a hydraulic system was the best system for a chassis dynamometer in terms of functionality, performance, and cost. Critical study of hydraulics, dynamometers, and data acquisition systems (DAQ) was followed by a complete design of a hydraulic system. The chassis dynamometer proposed in this …

California Olive Ranch Hedger, Tyler Enos, Seth Abbott, David Gamba

Mechanical Engineering

The purpose of this project is to evaluate the problems of the current KCI (Kingsburg Cultivator Incorporated) olive tree hedger in use at California Olive Ranch (COR) in Artois, CA, and then correct these problems which should yield a better performing, more efficient, and reliable machine. These problems include: the hydraulic oil temperature getting too high, the saw blades not having enough horsepower, and poor cutting performance due to operator error as well as terrain variations.

A Model Predictive Control Approach To Roll Stability Of A Scaled Crash Avoidance Vehicle, Nikola John Linn Noxon

Master's Theses

In this paper, a roll stability controller (RSC) is presented based on an eight degree of freedom dynamic vehicle model. The controller is designed for and tested on a scaled vehicle performing obstacle avoidance maneuvers on a populated test track. A rapidly-exploring random tree (RRT) algorithm is used for the vehicle to execute a trajectory around an obstacle, and examines the geographic, non-homonymic, and dynamic constraints to maneuver around the obstacle. A model predictive controller (MPC) uses information about the vehicle state and, based on a weighted performance measure, generates an optimal trajectory around the obstacle. The RSC uses the …