Structural Materials Commons^™

Microstructural Characterization Of Shear Transformation Zones And Modeling Indentation Size Effect In Amorphous Polymers, Leila Malekmotiei

LSU Doctoral Dissertations

The first aim of this work is developing a procedure for experimental and analytical characterization of nano-scale microstructures which mediate large scale deformation in amorphous polymers. Glassy polymers are extensively used as high impact resistant, low density, and clear materials in industries. Nevertheless, their response under severe loading conditions is yet to be appropriately unraveled. Due to the lack of long-range order in the microstructures of glassy solids, their plastic deformation is different from that in crystalline solids. Shear Transformation Zones (STZs) are believed to be the main plasticity carriers in amorphous solids and defined as the localized atomic or …

Modeling And Simulation Of Mass Flow Of Steel Plate/Slab During Hot Rolling, X. Wang, S. Ganguly, K. Chandrashekhara, Mario F. Buchely, Semen Naumovich Lekakh, David C. Van Aken, Ronald J. O'Malley, D. Bai, Y. Wang, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The ability to predict mass flow behavior during hot rolling is essential to product quality. In this study, viscoplastic models of the steels from SSAB and U.S. Steel were developed based on experimental stress-strain curves. A three-dimensional nonlinear finite element model was built to simulate a reverse plate hot rolling and a hot strip rolling process. For plate rolling, a seven pass schedule was simulated. The plastic strain distributions during rolling were investigated. The results show that the surface of the plate has larger plastic strain than the center. In the case of hot strip rolling, the simulation predicts that …

Anomalous 304 Stainless Steel Mechanical Properties In Medical Guide Wires, Andrew Joseph Freeman

Materials Engineering

Stainless steel medical guide wire cores, processed by Abbott Vascular, are returning anomalous mechanical properties upon strain hardening and heat treatment. As theory dictates, mechanical strength properties increase with strain hardening, and decrease with an annealing treatment. The opposite response is being observed. This is counter intuitive to fundamental materials knowledge, and a perfect materials engineering paradox. This project was designed to characterize these behaviors, and attempt to determine causation. To accomplish this, tensile testing of all processing steps mapped the mechanical property evolution of the wire. Published literature research revealed the potential of nitrogen and chromium solid state diffusion …

Mechanical Characterization Of Selectively Laser Melted 316l Stainless Steel Body Centered Cubic Unit Cells And Lattice Of Varying Node Radii And Strut Angle, Christopher James Hornbeak

Master's Theses

An experimental study of several variants of radius and strut angle of the body centered cubic unit cell was performed to determine the mechanical properties and failure mechanisms of the mesostructure. Quasi static compression tests were performed on an Instron® universal testing machine with a 50kN load cell at 0.2mm/min. The test samples were built using a SLM Solutions 125 selective laser melting machine with 316L stainless steel. Test specimens were based on 5mm cubic unit cells, with a strut diameter 10% of the unit cell size, with skins on top and bottom to provide a cantilever boundary constraint. Specimens …

Development Of Low Cost, Environmentally Friendly And High Strength Carbon Foams From Bread And Cake, Laura Mountain-Tuller

Materials Engineering

Carbon foam is a high niche material that consists of a highly porous, three-dimensional cellular network that is characterized by extremely high strength-to-weight ratios and low thermal conductivity. Due to these properties, carbon foams excel in structural and thermal applications, especially in the aerospace industry. Typically, carbon foams are formed through a heating process called pyrolysis of polymer precursors with high carbon content. This process is done at high temperatures in an oxygen free environment. These precursors are expensive to make and use toxic chemicals to produce, therefore, there is a push to find an environmentally friendly and cost-effective method …

Composite Suspension For A Mass Market Vehicle, Sarah M. Chapiama, Brian Auyeung, Jose Guerrero, Ethan Lau

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

The Effects Of Varying Composition And Build Direction On Direct Metal Deposition Fabricated Inconel 718, Abigail P. Nilan, Jessica M. Fordham

Materials Engineering

Inconel 718 (IN718) is a popular wrought superalloy, and is currently being investigated for additive manufacturing (AM) applications in the aerospace industry. However, overaging and the presence of microcracks have caused a significant reduction in properties. The purpose of this study is to meet or exceed the mechanical properties of wrought IN718 by varying the composition and build direction of the AM alloy. Alternative compositions were selected with Oerlilon Metco’s Rapid Alloy Development (RAD) software, and differ in niobium content, which increases the fraction of the primary strengthening phase (γʺ). Direct metal deposition (DMD) was used to fabricate the samples, …

Development Of Test Methods For Measuring Fiber Misalignment And Warping In Honeycomb-Core Composite Panels, Wyatt Taylor, Haripriya Nilakantan

Materials Engineering

Zodiac Aerospace manufactures honeycomb-core composite panels to be used in aircraft cabin interior components. During the manufacturing process, some panels become warped such that they cannot be used for their designated aircraft cabin components. As a result, these panels are scrapped because they cannot be recycled. About 44 to 90% of panels become warped during manufacturing. Warping is caused by many factors, including layer misalignment, processing parameters such as temperature and pressure gradients, and fiber misalignment in the prepregs. Currently, Zodiac does not have any data on the effect of fiber misalignment on panel warpage, so a testing protocol was …

Investigation Of Nanomaterial Based Photovoltaic Panel Packaging Materials, Xingeng Yang

Graduate Theses and Dissertations

In this research, nanomaterial-based packaging materials for photovoltaic (PV) panels are investigated. A hydrophobic/anti-reflective surface coating which not only repels water from the top glass of a PV panel but at the same time reduces its light reflectance is investigated. COMSOL simulation results indicate that taller ellipsoid rod (aspect ratio = 5) reflects less light than shorter rod (aspect ratio = 0.5) in the desired spectrum for solar energy harvest from 400nm-700nm. The addition of a polymer layer on these ellipsoid rods broadens the light incident angle from 23° to 34°, from which light can be efficiently absorbed. Based on …

Understanding The Evolution Of Surface Texture Under Boundary Lubrication, Salil T. Bapat

Graduate Theses and Dissertations

The objective of this research was to understand the evolution of surface texture under boundary/mixed lubrication (BL). Significant material/energy losses occur during BL because of direct contact between the two surfaces. Traditionally, tribofilms have been studied extensively for BL while textures have been used as a static engineering design parameter to enhance lubricant film properties. However, texture is dynamic at the tribological mating interface, where both physical and chemical interactions are continuously modulated. The evolution and the interplay between the tribofilm and texture is least studied in the literature, which is the focus of this research.

MoS2-based lubricants, known for …

Hawai'i Wildlife Fund V. County Of Maui, Lowell J. Chandler

Public Land & Resources Law Review

In Hawai’i Wildlife Fund v. County of Maui, the Ninth Circuit held that the plain language of the Clean Water Act provides jurisdiction over indirect discharges of pollutants from a point source into groundwater that is shown to be connected to navigable waters. The court found that studies confirmed pollutants entering the Pacific Ocean were fairly traceable to the County of Maui’s sewage disposal wells. In affirming the district court’s ruling, the Ninth Circuit held that Maui County violated the Clean Water Act by discharging pollutants into a navigable water without the required permit. The court also concluded the …

A Laboratory Kit For Multimeter Design, Seth Percy, Joshua Perry

Thinking Matters Symposium Archive

The multimeter is an important electrical tool and is a combination of many individual instruments. In practice, common multimeter designs are digital and measure voltage, current, resistance, capacitance, etc., using a single set of probes. Before the digital age, the world relied on analog displays. Some argue that analog displays are outdated technology. However, this overlooks one of the most important characteristics provided by the analog display, which is its ability to provide an instantaneous visual perception. Analog displays are currently used for many applications in aviation and automobiles, demonstrating their continuing usefulness in the field. In the multimeter, the …

Manufacturing Process Simulation – On Its Way To Industrial Application, Dennis Otten, Tobias A. Weber, Jan-Christoph Arent

International Journal of Aviation, Aeronautics, and Aerospace

Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview …

Propeller Design Requirements For Quadcopters Utilizing Variable Pitch Propellers, Ian R. Mcandrew, Elena Navarro, Ken Witcher

Publications

Unmanned aerial vehicles, UAV, has increases in the drastically in these past several years since their costs reduced. This research is based and built upon previous research presented in a conference. With the advent of commercial Quadcopters, four propeller systems, are used, being designed and used to operate the advantages of both flight and hovering. The basic design of their propeller blades has not evolved from the early days of manned flight when wooden fixed blades were used. In this paper that expands upon previous findings and discussions it explores the historical developments. Furthermore, how the expansion and reduction in …

Evaluation Of The Effect Of Tack Coat Type, Application Rate, And Surface Type On Interlayer Shear Strength, Chamika Prashan Dharmarathna

Electronic Theses and Dissertations

Tack coat is an asphaltic material applied between asphalt pavement layers. Since pavement is a multilayered structure, it is highly important to make proper bond between the layers to achieve a monolithic behavior. Hence, inadequate bond due to application of inadequate amount of tack coat may lead to poor structural behavior and premature failure. Also, applying excessive amount of tack coat may lead to layer slippage and binder migration. Therefore, it is highly important to apply an optimum amount of tack coat between layers. Over the past decades several studies have been conducted to determine the optimum tack coat application …

Direct Strength Approach To Predict The Flexural Strength Of Cold-Formed Z-Section Purlins On Sloped Roofs, Ali Parva, Michael W. Seek

Engineering Technology Faculty Publications

In this study, the strength of cold-formed Z-section purlins is predicted considering the effects of roof slope in real roof systems. The study applies to simple span purlins with torsion restraints at support locations and at paired locations along the length of the member. A previously developed method has shown through comparisons to base tests that when the biaxial bending and torsion stresses are incorporated into the analysis, the Direct Strength Method can accurately predict the strength of a purlin. These stress distributions can deviate substantially from the constrained bending approximation typically assumed in analysis and therefore impacts the local …

Assisted Development Of Mesophase Pitch With Dispersed Graphene And Its Resulting Carbon Fibers, Aaron Owen

Theses and Dissertations--Mechanical and Aerospace Engineering

The efficacy of dispersed reduced graphene oxide (rGO) as a nucleation site for the growth of mesophase in an isotropic pitch was investigated and quantified in this study. Concentrations of rGO were systematically tested in an isotropic petroleum and coal-tar pitch during thermal treatments and compared to pitch without rGO. The mesophase content of each thermally treated pitch was quantified by polarized light point counting. Further characterization of softening temperature and insolubles were quantified. Additionally, the pitches with and without rGO were melt spun, graphitized, and tensile tested to determine the effects of rGO on graphitized fiber mechanical properties and …

Nondestructive Evaluation Of Salvage White Spruce, Tyler Hovde

Dissertations, Master's Theses and Master's Reports

Knowledge of wood quality in dead standing trees is an important topic with recent increases in defoliation across North America. Obtaining wood quality information for defoliated trees would help stakeholders in the timber products industry sort and sell salvaged material for the highest possible value. This research investigates the ability to measure wood quality of white spruce (Picea glauca) after spruce budworm (Choristoneura fumiferana) attack using acoustic nondestructive evaluation. We compared stress wave velocities measured on standing trees to trees’ visual appearance. After harvest and processing of selected trees into bolts, standing-tree stress wave velocities were compared to bolt acoustic …

A Microstructure-Based Model Validated Experimentally For Quantification Of Short Fatigue Crack Growth In Three-Dimensions, Pei Cai

Theses and Dissertations--Chemical and Materials Engineering

Built on the recent successes in understanding the crystallographic mechanism for short fatigue crack (SFC) growth across a grain boundary (GB) and developing an experimental method to quantify the GB resistance against short crack growth, a microstructure-based model was developed in this study to simulate the growth behaviors of SFCs in 3-D, by taking into account both the driving force and resistance along at each point along the crack front in an alloy. It was found that the GB resistance was a Weibull function of the minimum twist angle of crack deflection at the boundary in AA2024-T3 Al alloys. In …

The Formation Mechanism Of Α-Phase Dispersoids And Quantification Of Fatigue Crack Initiation By Experiments And Theoretical Modeling In Modified Aa6061 (Al-Mg-Si-Cu) Alloys, Gongwang Zhang

Theses and Dissertations--Chemical and Materials Engineering

AA6061 Al alloys modified with addition of Mn, Cr and Cu were homogenized at temperatures between 350 ^ºC and 550 ^ºC after casting. STEM experiments revealed that the formation of α-Al(MnFeCr)Si dispersoids during homogenization were strongly affected by various factors such as heating rate, concentration of Mn, low temperature pre-nucleation treatment and homogenization temperature. Through analysis of the STEM results using an image software Image-Pro, the size distributions and number densities of the dispersoids formed during different annealing treatments were quantitatively measured. It was revealed that increasing the heating rate or homogenization temperature led to a reduction of …