Materials Science and Engineering Commons^™

Synergetic Adsorptive Mechanisms, Reusability And Cost Evaluations Of Green Fabricated Hybrid Barium Cobalt Nanocomposites For Methylene Blue And Lead Removal From Wastewater, Titus Chinedu Egbosiuba, Chibuike Christogonus Njoku, Ijeoma Jacinta Ani, Godwin Ifeanyi Ogbuehi, Abdulkareem Omeiza Yusuf, Abiodun Azeez Saka, Ugochukwu Ewuzie, Ebuka Emmanuel Ezennajiego, Blessing Onyinye Okafor, Walter Chibuike Anene, Cecilia Chika Unegbu, Florence Acha, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Barium nanoparticles (BaNPs), cobalt nanoparticles (CoNPs), and hybrid barium-cobalt nanocomposites (BaCoNCs) were synthesized using an eco-friendly green technique with Anacardium occidentale leaf extract for sequestration of methylene blue (MB) dye and lead (Pb (II)) ions from industrial wastewater. The nanoparticles and nanocomposites were characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM), and Brunauer-Emmett-Teller (BET) analysis to assess their functional groups, crystalline structure, morphology, and surface properties, confirming successful synthesis. Batch adsorption studies showed that optimal pollutant removal occurred at pH values of 8 for MB and 5 for Pb(II), with a contact time …

Tensile Creep Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Waleed S. Alshehri

Theses and Dissertations

Advanced aerospace systems require structural materials that can perform reliably in high-temperature environments for long durations. The performance of standard polymer matrix composites (PMCs) in these conditions is often limited by their susceptibility to time-dependent deformation, such as creep. The objective of this research is to characterize the high-temperature creep behavior of a novel unitized material system comprising a polymer matrix composite (PMC) and a ceramic matrix composite (CMC) co-cured together. The PMC part consists of the polyimide matrix reinforced with laminated carbon fibers woven in an eight harness satin weave (8HSW). The CMC part consists of a zirconia-based ceramic …

Enabling Carbon Dioxide Mineralization And Active Set Control In Portlandite-Based Cementitious Suspensions, Xiaodi Dai, Sharu Bhagavathi Kandy, Rui Xiao, Manas Sarkar, Shubham Wani, Thiyagarajan Ranganathan, Narayanan Neithalath, Aditya Kumar, Mathieu Bauchy, Edward Garboczi, Torben Gädt, Samanvaya Srivastava, Gaurav Sant

Materials Science and Engineering Faculty Research & Creative Works

The real-time control of concrete's stiffening allows users to better control pumping and extrusion during 3D-printing processes. Here, a portlandite-based cementitious formulation (i.e., slurry or suspension) that features the potential for rapid CO₂ uptake is adapted for 3D-printing applications. In particular, we showcase a portlandite-fly ash binder system combined with a thermo responsive polymer, wherein precise control via thermal activation allows set control and rapid solidification. Through the thermally induced polymerization of polyacrylamide, the hybrid binder system rapidly undergoes stiffening at trigger onset temperatures ranging from 60 °C to 80 °C, exhibiting average stiffening rates of up to 2600 …

In Situ High-Temperature Raman Spectroscopy For Online Eaf Slag Analysis, Bohong Zhang, Hanok Tekle, Ronald J. O'Malley, Jeffrey D. Smith, Farhan Mumtaz, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

Real-time monitoring of slag chemistry is critical for optimizing Electric Arc Furnace (EAF) steelmaking operations, where dynamic variations in slag composition directly influence slag foaming, refractory degradation, and thermal efficiency. Conventional techniques such as X-ray fluorescence (XRF), Fourier-transform infrared (FTIR), and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS) are commonly used to analyze slag composition, but their offline nature and equipment constraints limit their applicability for online monitoring in harsh industrial environments. To address this challenge, we present an in situ, high-temperature analytical approach that integrates Raman spectroscopy with a custom-designed fiber-optic probe for real-time slag characterization at …

A Green Concrete Mixture Using Rice Husk As Partially Cement Replacement, Khloud Khalid Eldamshiry, Zeina Salama, Amany Micheal, Rania Rushdy Moussa, Ayatallah Raafat

Architectural Engineering

Egypt's agricultural waste production has increased significantly in recent decades, leading to improper disposal methods and environmental pollution. Rice husks are the most common agricultural solid waste in Egypt, contributing to "black clouds" and causing health issues. On the other hand, Cement, a crucial component of construction materials, generates unsound residues and greenhouse gas emissions. Green concrete with rice husks could be a profitable solution for environmentally sound construction, reducing cement consumption and increasing the durability and integrity of new materials. This study investigates the use untreated rice husk fibres with a concrete mixture, avoiding burning and contributing to environmental …

Effect Of Contact Time And Concentration On Adsorption Of Pb2+Metal Ion Utilizing Crab Shell Chitosan And Activated Bentonite Clay Composite, Nia Sasria, Adi Wisaka, Ade Wahyu Yusariarta Putra Parmita, Gusti Umindya Nur Tajalla

Makara Journal of Technology

Indonesia produced 1,508 tons of nonliving crabs in the January–March 2020 period. The number of shells generated can account for 40%–60% of the overall weight. Therefore, using crab shells made into chitosan is expected to increase the economic value and reduce waste from crab shells. Chitosan can be modified with clay previously activated with an acid solution to form a chitosan–clay composite to improve the adsorption capacity. This study aims to analyze the differences in characteristics between chitosan and clay before and after the immobilization process. A comparison of chitosan and clay (1:2) is conducted on the basis of variations …

Piezoelectric Dc Generator Through Sequential In-Phase Polarization Variation, Hyun Soo Kim, Sunghoon Hur, In Woo Oh, Chulwan Lim, Huimin Qiao, Hyung Jin Choi, Min Seok Kim, Dae Sol Kong, Jong Hoon Jung, Joonchul Shin, Seung Hyub Baek, Jun Chen, Chong Yun Kang, Jeong Min Baik, Yu U. Wang, Shashank Priya, Seong H. Kim, Yunseok Kim, Hyung Suk Oh, Kyung Hoon Cho, Jungho Ryu, Hyun Cheol Song

Michigan Tech Publications

Energy harvesting has drawn growing interest as a reliable power source for IoT applications, with piezoelectric materials notable for their high sensitivity and straightforward integration. Their robust mechanical-electrical coupling also makes them ideal for harnessing environmental vibrations or mechanical motions. Still, standard piezoelectric harvesters inherently produce alternating current (AC), necessitating complex rectification steps and leading to substantial energy loss. This work introduces a direct current (DC) harvesting method that employs a novel in-phase polarization strategy, enabling a stable, continuous DC output. This approach surpasses prior attempts that offered only low or pulsed DC signals, achieving an open-circuit voltage of 33.44 …

Effect Of Saccharin On Crystallization Behavior Of Electroless Cobalt Plating, Yu-Xin Luo, Jing-Jing Wang, Lu Wang, Zi-Yi Yan, Yi Ma, Xin Bo, Jing-Shuang Dang, Zeng-Lin Wang

Journal of Electrochemistry

In the process of electroless cobalt plating, the saccharin additive can significantly change the surface morphology, texture orientation, and conductivity of the cobalt coating layer. When the amount of saccharin was 3 mg·L^–1, the cobalt coating transformed from disordered large grains to a honeycomb structure, with a preferred orientation of (002) facet on hexagonal close-packed (HCP) cobalt crystals. The resistivity of the cobalt film decreased to 14.4 μΩ·cm, and further decreased to 10.7 μΩ·cm after the annealing treatment. When the concentration of saccharin was increased, the grain size was gradually refined and a “stone forest” structure was observed, …

Superhydrophilic Porous Coooh Nano-Architecture With Abundant Oxygen Vacancies For Enhanced Urea Electrooxidation At Ampere-Level Current Densities, Wen-Jing Lv, Xiao-Man Tang, Xue-Tong Wang, Wen-Cai Liu, Jian-Wen Zhu, Guo-Jing Wang, Yuan-Zhi Zhu

Journal of Electrochemistry

The conversion of urea-containing wastewater into clean hydrogen energy has gained increasing attention. However, challenges remain, particularly with sluggish catalytic kinetics and limited long-term stability of urea oxidation reaction (UOR). Herein, we report the loosely porous CoOOH nano-architecture (CoOOH LPNAs) with hydrophilic surface and abundant oxygen vacancies (O_v) on carbon fiber paper (CFP) by electrochemical reconstruction of the CoP nanoneedles precursor. The resulting three-dimensional electrode exhibited an impressively low potential of 1.38 V at 1000 mA·cm⁻² and excellent durability for UOR. Furthermore, when tested in an anion exchange membrane (AEM) electrolyzer, it required only 1.53 V at …

Structure Regulation Engineering For Biomass-Derived Carbon Anodes Enabling High-Rate Dual-Ion Batteries, Rui Zhou, Rui Liu, Yun-Nuo Li, Si-Jie Jiang, Tian-Tian Jing, Yan-Song Xu, Fei-Fei Cao

Journal of Electrochemistry

Dual-ion batteries (DIBs) usually use carbon-based materials as electrodes, showing advantages in high operating voltage, potential low cost, and environmental friendliness. Different from conventional “rocking chair” type secondary batteries, DIBs perform a unique working mechanism, which employ both cation and anion taking part in capacity contribution at an anode and a cathode, respectively, during electrochemical reactions. Graphite has been identified as a suitable cathode material for anion intercalation at high voltages (> 4.8 V) with fast reaction kinetics. However, the development of DIBs is being hindered by dynamic mismatch between a cathode and an anode due to sluggish Li^{+ …}

First Principles Materials Discovery And Design For Photovoltaic And Solar Thermal Alloys Using High Throughput Methods, Andrew Pike

Dartmouth College Ph.D Dissertations

Materials selection has been a challenge since the dawn of time. With the advent of computational methods and high throughput databases, materials can be discovered and assessed before they are even synthesized. In this thesis I will discuss my work towards designing new materials for clean energy uses, especially alloys which have been underexplored from computational methods. To begin, I present a case study explaining the synthesis of the Yb₁₄ZnSb₁₁ thermoelectric material. Next, I explore the class of AM₂Pn₂ Zintl materials. From the previously identified BaCd₂P₂, it is suspected that …

Design And Optimization Of Anode Catalysts For Direct Ethanol Fuel Cells: Advances And Challenges In C-C Bond Activation And Selective Modulation Of The C1 Pathway, Kai-Chi Qin, Meng-Tian Huo, Yu Liang, Si-Yuan Zhu, Zi-Hao Xing, Jin-Fa Chang

Journal of Electrochemistry

Direct ethanol fuel cells (DEFCs) are a promising alternative to conventional energy sources, offering high energy density, environmental sustainability, and operational safety. Compared to methanol fuel cells, DEFCs exhibit lower toxicity and a more mature preparation process. Unlike hydrogen fuel cells, DEFCs provide superior storage and transport feasibility, as well as cost-effectiveness, significantly enhancing their commercial viability. However, the stable C–C bond in ethanol creates a high activation energy barrier, often resulting in incomplete electrooxidation. Current commercial platinum (Pt)- and palladium (Pd)-based catalysts demonstrate low C–C bond cleavage efficiency (

3d-Printable Hydrogel With Rapid Ambient Self-Healing, Anna M. Petre

Research from the Berry Summer Thesis Institute, 2025

Inspired by nature, soft robots composed of compliant (“soft”) materials are well-suited for uncertain, dynamic tasks requiring safe interaction between a robot and its environment. Soft robots with the ability mend minor damage (e.g. perforations, tears) have been enabled by the rapid development of self-healing soft materials. Recently, one of these hydrogel materials (internally dubbed “BeckOHflex”) – made entirely from commercially available precursors – was developed with several appealing characteristics including rapid ambient self-healing, 3D printability on commercial machines, and competitive mechanical properties. However, the self-healing performance of BeckOHflex falls short of competitors that leverage custom-synthesized precursors. This project aims …

Recent Progress And Scientific Challenges In Wire-Arc Additive Manufacturing Of Metallic Multi-Material Structures, Sainand M. Jadhav, Sambhaji Kusekar, Akash Belure, Satyavan Digole, Abhijeet Mali, Muralimohan Cheepu, Manoj Mugale, Suhas Alkunte, Duckbong Kim

Faculty Articles

Metallic multi-material structures are heterogeneous structures characterized by changing composition, microstructures, and site-specific characteristics, advantageous for numerous applications where multifunctionality is desired. Metallic multi-material structures are known as bimetallic structures (BSs), which are functionally graded materials (FGMs). In recent years, wire-arc additive manufacturing (WAAM) advanced as a promising additive manufacturing process to realize the fabrication of these structures due to its high deposition rate, cost-effectiveness, and material utilization efficiency. This review presents a comprehensive overview of the recent progress, processing strategies, and scientific challenges in WAAM of multi-material structures. The paper begins with an introduction to multi-material structures, followed by …

Recent Progress And Scientific Challenges In Wire-Arc Additive Manufacturing Of Metallic Multi-Material Structures, Sainand Jadhav, Sambhaji Kusekar, Akash Belure, Satyavan Digole, Abhijeet Mali, Muralimohan Cheepu, Manoj Mugale, Suhas Alkunte, Duckbong Kim

EKU Faculty and Staff Scholarship

Metallic multi-material structures are heterogeneous structures characterized by changing composition, microstructures, and site-specific characteristics, advantageous for numerous applications where multifunctionality is desired. Metallic multi-material structures are known as bimetallic structures (BSs), which are functionally graded materials (FGMs). In recent years, wire-arc additive manufacturing (WAAM) advanced as a promising additive manufacturing process to realize the fabrication of these structures due to its high deposition rate, cost-effectiveness, and material utilization efficiency. This review presents a comprehensive overview of the recent progress, processing strategies, and scientific challenges in WAAM of multi-material structures. The paper begins with an introduction to multi-material structures, followed by …

Performance Properties Of Treated Jute Fabric Laminated By Electrospun Recycled Pet Nanofibers, Md Abdus Shahid, Md Golam Mortuza Limon, Imam Hossain, Md Tanvir Hossain, Tarikul Islam, Md Moslem Uddin

Michigan Tech Publications

Transforming from plastic to environmentally friendly materials is essential for both human health and the protection of the environment. In this work, a modified jute fabric (MJF) laminated with electrospun recycled polyethylene terephthalate (rPET) nanofibers with silver nitrate (AgNO3) is presented. The purpose to apply the silver nitrate and rPET nanofiber mat is to enhance the performance properties of packaging materials like mechanical strength, thermal insulation, moisture resistance, and antibacterial properties. The jute fabric was pretreated with alkali to make it compatible with rPET electrospun nanofibers, which improved breathability with a diameter of 24.70 ± 7.79 nm and an average …

Polymeric Nanocarriers Functionalized With Peptides For Improved Glioblastoma Targeting And Blood–Brain Barrier Permeability, Cristian Antonio Wieczorek Villas Boas, Aaron Priester, Buck E. Rogers, Anthony J. Convertine

Materials Science and Engineering Faculty Research & Creative Works

We report the synthesis of polymeric conjugates designed to penetrate the blood–brain barrier (BBB) and selectively bind glioblastoma (GBM) cells through reversible addition–fragmentation chain transfer (RAFT) polymerization. The resulting materials were engineered to contain peptide macromonomers for cell-specific targeting and integrated DOTA units to facilitate radiolabeling with copper-64 (⁶⁴Cu), yielding radiolabeled conjugates with greater than 95% radiochemical purity. In biodistribution assessments conducted in mice, C1C2 peptide-conjugated polymers showed significantly improved accumulation in brain tissue, supported by brain perfusion analyses confirming efficient BBB penetration. Additionally, flow cytometry evaluations demonstrated specific affinity of GBM-targeted polymer formulations toward U87 glioblastoma cells. …

Ceramic Waste As Sustainable Material In Self-Compacting Concrete: Experimental Study And Ann Predictive Modeling, Abderrezak Bouziane, Houssam Slimanou, Mohamed Amin Bouzidi, Nedjima Bouzidi

Journal of Sustainable Construction Materials and Technologies

Recycling of ceramic waste in the construction sector is a promising option for reducing the environmental impacts of the concrete industry. The main objective of this study is the elaboration of a solid predictive model for ceramic waste based self-compacting (SCC) concrete properties, using artificial neural networks (ANN). This further, reduces its environmental impact without compromising satisfactory performance. An experimental approach was adopted with different substitution ratios: 0 to 30 wt% and particle sizes ranging from 3-8 mm and 8-15 mm. Tested properties of modified SCC as compressive strength at 7 and 28 days (fc7, fc28), spread (L), sieve stability …

Comparative Study On The Performance Of Ggbs, Uggbs, And Rha-Incorporated Cement Mortar Mixes, Devansh Goel, Sudarshan D. Kore

Journal of Sustainable Construction Materials and Technologies

The environmental footprint of cement production has accelerated the pursuit of sustainable alternatives in the construction industry. Supplementary cementitious materials (SCMs), particularly those derived from industrial and agricultural waste, offer a promising approach to reducing cement consumption while maintaining performance. This study evaluates the fresh and mechanical behavior of binary, ternary, and quaternary cementitious mortar blends incorporating ground granulated blast-furnace slag (GGBS), ultrafine GGBS (UGGBS), and rice husk ash (RHA) as partial replacements for cement. A total of 32 mortar mixes were designed with water-to-binder (w/b) ratios ranging from 0.3 to 0.5 and varied replacement levels of RHA (0-20%), GGBS …

Magnetic Molecularly Imprinted Polymers For Quercetin Adsorption: Fabrication, Characterization, And Application, Vinitha Ug

Theses and Dissertations

A highly selective Magnetic Molecularly Imprinted Polymer (MMIP) was developed for the detection and purification of Quercetin. The Density Functional Theory was utilized for the selection of suitable monomers based on binding energy interaction between quercetin and monomers (Acrylamide, Acrylonitrile, Methacrylic Acid). From computational studies, Acrylamide was selected as a suitable monomer for the synthesis of MMIP. Under ultrasound irradiation both quercetin and naringin imprinted materials MMIP-Q and MMIP-N were fabricated.

Compared to ultrasound-assisted synthesis, Microwave Synthesis provides uniform heat transfer throughout the reaction solution, which enables uniformity in the size of synthesised material, increases the yield of material and …