Materials Science and Engineering Commons^™

Research Progress In Carbon Coating On Lifepo4 Cathode Materials For Lithium Ion Batteries, Ning Zhang, Yong-Chang Liu, Cheng-Cheng Chen, Zhi-Qiang Zhu, Zhan-Liang Tao, Jun Chen

Journal of Electrochemistry

Olivine-structured LiFePO₄ has been received much attention because of its flat voltage profile, low cost, abundant material supply and better environmental compatibility. However, the poor electronic and ionic conductivities have limited its application in industry. One of the best methods to improve the electrochemical performance is carbon coating. In this review, we summarize the recent developments of LiFePO₄/C cathode. Moreover, the different effects caused by coating methods and carbon sources, as well as the mechanism of carbon coating on the properties of LiFePO₄/C are reviewed.

Enhancing Stability Of Pem Fuel Cell Catalysts Via Support Changing, Xiao-Hong Xie, Zi-Dong Wei

Journal of Electrochemistry

The Pt/C catalyst with highly dispersed Pt nanoparticles supported on carbon has been widely used as the state-of the-art catalyst in proton exchange membrane fuel cells (PEMFCs), while the durability of Pt/C is one of the major barriers for large-scale applications of PEMFCs. Thus, enhancing the stability of Pt/C has been a hot issue in this field. In this review, we summarize the recent progress in enhancing the catalyst stability in the view of support material. The future prospects of the PEMFCs catalyst should focus on adopting more stable supports or strengthening the interactions between Pt and supports.

Pt/C Modified Proton Exchange Membrane For Improved Fuel Cell Performance, Zhi Cui, Chao Wang, Shui-Yun Shen, Feng-Jing Jiang, Jun-Liang Zhang

Journal of Electrochemistry

The property of proton exchange membrane greatly affects the performance of proton exchange membrane fuel cells (PEMFC). During the operation of a PEMFC, the water produced at the cathode, the water vapor from the humidified feed gas and the water migrated by electro-dragging will reach a balance in the membrane and determine the resistance of PEMFC, and thus affect the performance of PEMFC. Normally, the PEMFC performance strongly depends on the relative humidity of the feed gas, and the performance decreases at lower humidity as a result of lower proton conductivity of the membrane. In this paper, we proposed to …

Lithium Air Batteries: Non-Aqueous And Hybrid Systems, Sheng-Fu Tong, Ping He, Xue-Ping Zhang, Shi-Yong Zhao, Hao-Shen Zhou

Journal of Electrochemistry

Developing energy storage devices and new materials, which match the requirements in electric vehicles (EVs) and hybrid electric vehicles (HEVs), is an effective way to balance the contradiction between the social development and the shortage of fossil energy and environment pollution. Rechargeable lithium-air (Li-air) batteries consisting of Li and oxygen as the anodic and cathodic reactants, respectively, have attracted much attention during the past decade due to their high theoretical specific energy. According to work conditions, the most studied types of Li-air batteries are non-aqueous, hybrid, and solid state electrolyte Li-air batteries. Challenges still exist in cathodes, anodes, electrolytes and …

Preparation Of Zro2-Doped Nb/Pbo2 Electrode And Electrocatalytic Performance Of Methyl Orange Degradation, Li Zhang, Wen-Yan Dong, Tai-Lai Yang, Zhen-Hai Liang

Journal of Electrochemistry

The zirconium oxide (ZrO₂)-doped niobium based lead oxide (Nb/PbO₂) electrode was prepared by electrodeposition. The microstructures and electrochemical properties of Nb/ZrO₂+PbO₂ electrode were investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD), linear sweep voltammetry, electrochemical impedance spectroscopy and cyclic voltammotry. In addition, the Nb/PbO₂ electrode was used as an anode for the electrochemical degradation of methyl orange (MO). Results revealed that the ZrO₂ doping made the Nb/PbO2 electrode surface denser and rougher with smaller sized crystal particles, which increased the specific surface area and enhanced the electrocatalytic activity of the …

Electrolytes For Lithium And Lithium-Ion Batteries, Zong-Rang Zhang

Journal of Electrochemistry

This is an up-to-date book published by Springer last year and focuses on the field of the electrolytes for lithium and lithium-ion batteries. A brief introduction and review of this book are given in this paper. The main contents of this book are introduced briefly in the order of ten different chapters along with a short review of recent progress in those fields.

Analysis Of Particle Transport And Deposition Of Micron-Sized Particles In A 90° Bend Using A Two-Fluid Eulerian–Eulerian Approach, Erick S. Vasquez, Keisha B. Walters, D. Keith Walters

Chemical and Materials Engineering Faculty Publications

Two-phase flows involving dispersed particle and droplet phases are common in a variety of natural and industrial processes, such as aerosols, blood flow, emulsions, and gas-catalyst systems. For sufficiently dilute particle/aerosol phases, a simplified one-way coupling is often assumed, in which the continuous primary phase is unaffected by the presence of the dispersed secondary phase and standard CFD methods can be applied. To predict the transport and deposition of the particle phase, typically a Lagrangian particle-tracking or Eulerian one-fluid/two-phase drift-flux approach is used. Here, a full two-fluid Eulerian modeling approach is presented for coarse particles (>1 μm), in which …

Low-Cost Open-Source Voltage And Current Monitor For Gas Metal Arc Weld 3d Printing, Anthony Pinar, Bas Wijnen, Gerald C. Anzalone, Timothy C. Havens, Paul G. Sanders, Joshua M. Pearce

Department of Materials Science and Engineering Publications

Arduino open-source microcontrollers are well known in sensor applications for scientific equipment and for controlling RepRap 3D printers. Recently low-cost open-source gas metal arc weld (GMAW) RepRap 3D printers have been developed. The entry-level welders used have minimal controls and therefore lack any real-time measurement of welder voltage or current. The preliminary work on process optimization of GMAW 3D printers requires a low-cost sensor and data logger system to measure welder current and voltage. This paper reports on the development of a low-cost open-source power measurement sensor system based on Arduino architecture. The sensor system was designed, built, and tested …

Diffusion Of A Janus Nanoparticle In An Explicit Solvent: A Molecular Dynamics Simulation Study, Ali Kharazmi, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

Molecular dynamics simulations are carried out to study the translational and rotational diffusion of a single Janus particle immersed in a dense Lennard-Jones fluid. We consider a spherical particle with two hemispheres of different wettabilities. The analysis of the particle dynamics is based on the time-dependent orientation tensor, particle displacement, as well as the translational and angular velocity autocorrelation functions. It was found that both translational and rotational diffusion coefficients increase with decreasing surface energy at the nonwetting hemisphere, provided that the wettability of the other hemisphere remains unchanged. We also observed that in contrast to homogeneous particles, the nonwetting …

Consumer Perceptions Towards Package Designs: A Cross Cultural Study, Romica Chandra Lal, Fritz Yambrach, Lucy Mcproud

Journal of Applied Packaging Research

The choice of one package or the other can be an economic decision or can be influenced by cultural acceptance or perception of individual convenience. Product package systems can be designed for one-time use or multiple-use purposes. Package perceptions in different countries typically develop from a variety of factors, including climate, lifestyle, and cultural acceptance with regard to particular products. In an increasingly global economy with multinational firms marketing products worldwide, it is important to understand the differences between consumer needs and consumer responses to product-package systems.

The objective of this research was to examine consumer perceptions of different product …

Burner, Emitter, And Recuperator Development For Lightweight Thermophotovoltaic Power Supply, Lewis Fraas, Leonid Minkin, J. Avery, Hui She, L. Ferguson, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Like batteries, thermophotovoltaic generators produce DC electricity quietly. TPV uses infrared photovoltaic cells to convert infrared radiation from a combustion heated ceramic IR emitter. However, because the specific energy in a hydrocarbon fuel like propane or butane is 12,900 Wh/kg, much larger than the specific energy of 145 Wh/kg for a Li-ion battery, TPV is very promising as a lightweight DC power supply. A portable cylindrical thermophotovoltaic (TPV) battery replacement concept has been previously described. It consists of a cylindrical TPV receiver assembly using simple diffused junction GaSb IR cells along with a novel omega recuperator and a novel doped …

Spectrally-Resolved Imaging Of The Transverse Modes In Multimode Vcsels, Stephan A. Misak, Dan G. Dugmore, Kirsten A. Middleton, Evan R. Hale, Kelly R. Farner, Kent D. Choquette, Paul O. Leisher

Rose-Hulman Undergraduate Research Publications

Vertical-cavity surface-emitting lasers (VCSELs) enable a range of applications such as data transmission, trace sensing, atomic clocks, and optical mice. For many of these applications, the output power and beam quality are both critical (i.e. high output power with good beam quality is desired). Multi-mode VCSELs offer much higher power than single-mode devices, but this comes at the expense of lower beam quality. Directly observing the resolved mode structure of multi-mode VCSELs would enable engineers to better understand the underlying physics and help them to develop multi-mode devices with improved beam quality. In this work, a low-cost, high-resolution (<3 >pm) …

Temperature Dependent Surface Reconstruction Of Freely Suspended Films Of 4-N-Heptyloxybenzylidene-4-N-Heptylaniline, Daniel E. Martinez Zambrano

Lawrence University Honors Projects

Surfaces of freely suspended thick films of 4-n-heptyloxybenzylidene-4-n-heptylaniline (7O.7) in the crystalline-B phase have been imaged using non-contact mode atomic force microscopy. Steps are observed on the surface of the film with a height of 3.0 +/- 0.1 nm corresponding to the upright molecular length of 7O.7. In addition, we find that the step width varies with temperature between 56 and 59 degrees C. The steps are many times wider than the molecular length, suggesting that the steps are not on the surface but instead originate from edge dislocations in the interior. Using a strain model for liquid crystalline layers …

Characterization Of Pressure-Driven And Electro-Kinetically Driven Flow In A Micro-Fluidic Chip Using Particle Imaging Velocimetry, Alexis Weckel

Master's Theses

The flow profiles of pressure-driven and electro-kinetic driven flows were compared for a microfluidic chip. It was found that the pressure-driven flow had a parabolic profile while the electro-kinetic flow had a plug shaped flow profile. The measured velocities were similar to those determined by the Poiseuille flow model and the Helmholtz-Smoltchowski equation. Flow uniformity is very important for control in microfluidic mixers. Parabolic flow profiles lead to inconsistent reactions while the more uniform plug shape flow allow for a more steady reaction across the channel. Previous work had been performed to measure the flow of a solution of fluorescent …

An Investigation Of Incipient Melting During Solution Heat Treatment Of 7050 Aluminum Forgings And Its Effect On Corrosion Properties, Thomas Kilkenny

Materials Engineering

7050 alloy (6.2Zn-2.3Mg-2.3Cu-0.12Zr) is a structural aluminum alloy commonly used in the aerospace industry. Its rich chemistry makes it susceptible to incipient melting. Incipient melting is a phenomenon where areas with high local alloy content melt before the rest of the material. This can cause a degradation of mechanical and corrosion properties. A six by four factor solution heat treatment trial was conducted. Six solution heat treatment temperatures, 890- 940°F in 10°F increments, and four times, 1, 2, 4, and 6 hours, were used. Incipient melting was observed in the 910°F, 6 hour solution heat treatment and all 920-940°F solution …

Analysis Of Shear Strength Variance Of Ph 15-7 Mo Blind Rivet Stems For Aerospace Applications, Miles Macarthur, Kent C. Majewski

Materials Engineering

This project attempts to reduce manufacturing costs incurred to Cherry Aerospace by variance in material properties. To track and predict the shear strength of PH 15-7 Mo stainless steel rivet stems throughout the heat treatment process, samples were taken from several steps in the manufacturing process and experimental heat treatments were performed across a range of temperatures. The supplied rivet stems were heat treated for four hours at temperatures from 520°C to 560°C, in increments of 10°C. Double shear testing in accordance with ASTM 1312-13A revealed that there is no apparent correlation between the strength of the supplied wire and …

Effect Of Heat Treatment On The Mechanical Properties In Natural Bamboo, Austin Levy, Mackenzie Kirkpatrick

Materials Engineering

Previous studies have shown that heat treatments have the ability to improve mechanical strength and stiffness in hardwood species. Compared to structural hardwoods, bamboo is a more sustainable and globally viable renewable resource. Therefore, Bambusoides vivax (timber bamboo) culms were fabricated into flat, rectangular cross-section samples with varying cellulose content to be heat treated and tested for mechanical properties. All samples were heat treated (HT) twice. The first HT was a normalization of all samples at 103 +/- 3 °C. The second HT was performed at various times and temperatures ranging from 130°C to 170°C for 0.5 to 3 hours. …

Tensile Test Design To Measure Interlayer Adhesion In Investment Casting Shells For Spalling Mitigation, Shelby Boyd, Alex Miller, Jameson Senger

Materials Engineering

We designed a tensile test fixture for a 112 lbf capacity Instron load frame that imparts a normal force on the face of a button epoxied to an investment casting shell sample, delaminating the shell area attached to the button. Using a green standard shell (Group 1), a partially fired standard shell (Group 2), and a green shell with a different third coat (Group 3), we verified that the fixture can measure differences in strength between sample groups. We attached steel buttons to leveled samples with 0.05 mL of Hysol-Loctite 9340 epoxy, let it cure for 48 hours, and tested …

Effect Of Time Delay Between Etching And Adhesive Bonding (“Outlife” Time) On Lap-Shear Strength Of Aluminum Alloys Using Environmentally-Friendly P2 Etch, Josh Barkhimer, Matthew Erich, Gokul Nair

Materials Engineering

Raytheon Company currently uses a Forest Products Laboratory (FPL) paste etchant for preparing aluminum surfaces for adhesive bonding, and FPL is a source of hazardous hexavalent chromium. The goal of this study was to evaluate a less-toxic P2 paste etchant as a possible replacement. Coupons of 2024-T3, 6061-T6, and 7075-T6 grades of aluminum alloy were solvent-degreased, abrasively cleaned, and etched at room temperature using P2 paste following a strict protocol adopted from Raytheon. Coupons were then left exposed to air for assigned time intervals (or “outlife” times) of 0, 1, 4, 8, 16, and 63 or 72 hours. The aluminum …

Effects Of Composition And Solid Solution Strengthening On The Compression Strength Of Iron-Based Hardfacing Alloys, Tyler Wiggins, Samuel Garrison-Terry

Materials Engineering

Three iron-based hardfacing alloys were fabricated to have a tungsten strengthened matrix with varying compositions of 10-15, 20, and 30 wt% tungsten/chrome boride content. The fourth sample was fabricated to have a molybdenum solid solution strengthened matrix with 10-15 wt% W/Cr Boride content. This project focuses on the compressive strength of iron-based hardfacing alloys. Preliminary compression tests with Scoperta iron-based hardfacing alloys showed a need for sample dimension reduction due to compressive loads that could not be met by a 50 kN maximum capacity mechanical testing system. The preliminary tests showed compressive strengths exceeding 2340 MPa. Samples of the current …